Professional Documents
Culture Documents
2012 GENERAL INFORMATION Specifications - TL PDF
2012 GENERAL INFORMATION Specifications - TL PDF
2012 GENERAL INFORMATION Specifications - TL PDF
Specifications - TL
Standard or
Item Measurement Qualification Service Limit
New
930 kPa (9.48
Minimum -
Pressure (checked with engine starter kgf/cm2 , 134.8 psi)
Compression
cranking at wide-open throttle) Maximum 200 kPa (2.04
-
variation kgf/cm2 , 29.0 psi)
manual
Tuesday, February 16, 2016 2:28:45 PM Page 2 2005 Mitchell Repair Information Company, LLC.
2
2012 Acura TL
2012 GENERAL INFORMATION Specifications - TL
71.976- 72.000 mm
Main journal diameter (2.83370- 2.83464 -
in)
54.976- 55.000 mm
Rod journal diameter (2.16441- 2.16535 -
in)
0.005 mm (0.00020 0.010 mm
Crankshaft Rod/main journal taper
in) max. (0.00039 in)
Rod/main journal out-of- 0.005 mm (0.00020 0.010 mm
round in) max. (0.00039 in)
0.10- 0.35 mm 0.45 mm
End play
(0.0039- 0.0138 in) (0.0177 in)
0.025 mm (0.00098 0.030 mm
Total runout
in) max. (0.00118 in)
0.019- 0.045 mm
Main bearing-to-journal oil 0.050 mm
(0.00075- 0.00177
clearance (0.00197 in)
Crankshaft in)
bearing 0.020- 0.044 mm
Connecting rod bearing-to- 0.050 mm
(0.00079- 0.00173
journal oil clearance (0.00197 in)
in)
Service
Item Measurement Qualification Standard or New
Limit
Engine overhaul 5.0 L (5.3 US qt) -
Engine Oil change
Capacity 4.3 L (4.5 US qt) -
oil including filter
manual
Tuesday, February 16, 2016 2:28:45 PM Page 7 2005 Mitchell Repair Information Company, LLC.
7
2012 Acura TL
2012 GENERAL INFORMATION Specifications - TL
Service
Item Measurement Qualification Standard or New
Limit
Engine
8.3 L (2.19 US gal) -
Coolant capacities (including overhaul
engine, heater, hoses, and reservoir) Coolant
Radiator 6.3 L (1.66 US gal) -
change
Acura Long Life Antifreeze/Coolant
Coolant type
Type 2
Coolant
Coolant capacity 0.69 L (0.182 US gal) -
reservoir
93- 123 kPa (0.95- 1.25
Radiator cap Opening pressure -
kgf/cm2 , 13.5 - 17.8 psi)
Begins to open 169- 176F (76- 80C) -
Opening temperature
Thermostat Fully open 194F (90C) -
Valve lift at fully open 10.0 mm (0.394 in) min. -
Service
Item Measurement Qualification Standard or New
Limit
390- 440 kPa
Fuel (4.0- 4.5
pressure Pressure with fuel pressure gauge connected -
regulator kgf/cm2 , 57- 64
psi)
70.0 L (18.49 US
Fuel tank Capacity -
gal)
Idle speed without load In N or P 680 50 RPM
Idle speed with high electrical load (A/C switch
manual
Tuesday, February 16, 2016 2:28:45 PM Page 8 2005 Mitchell Repair Information Company, LLC.
8
2012 Acura TL
2012 GENERAL INFORMATION Specifications - TL
Standard or Service
Item Measurement Qualification
New Limit
390- 440 kPa
Fuel (4.0- 4.5
pressure Pressure with fuel pressure gauge connected -
regulator kgf/cm2 , 57- 64
psi)
70.0 L (18.49 US
Fuel tank Capacity -
gal)
M/T in
750 50 RPM
Idle speed without load neutral
A/T in N or P 700 50 RPM
Engine idle Idle speed with high electrical load (A/C switch M/T in
on, temperature set to max cool, blower fan on neutral 750 50 RPM
high, rear window defogger on, and headlights
on high beam) A/T in N or P 700 50 RPM
CLUTCH
Service
Item Measurement Qualification Standard or New
Limit
manual
Tuesday, February 16, 2016 2:28:45 PM Page 9 2005 Mitchell Repair Information Company, LLC.
9
2012 Acura TL
2012 GENERAL INFORMATION Specifications - TL
in)
2nd-3rd 0.04- 0.17
0.28 mm
Countershaft 2nd Clearance mm (0.002- 0.006
(0.011 in)
gear in)
22.91 - 22.99 mm 22.86 mm
Thickness
(0.9020- 0.9051 in) (0.9000 in)
45.970- 45.988 mm
46.04 mm
I.D. (1.80984- 1.81055
(1.8126 in)
in)
Countershaft 53.987- 54.000 mm
53.93 mm
reverse gear O.D. (2.12547- 2.12598
(2.1232 in)
in)
23.03- 23.08 mm
Length -
(0.9067- 0.9087 in)
42.990- 43.000 mm
43.05 mm
I.D. (1.69252- 1.69291
(1.6949 in)
in)
Countershaft 2nd
51.989- 52.000 mm
gear distance 51.94 mm
O.D. (2.04681- 2.04724
collar (2.0449 in)
in)
23.03- 23.08 mm
Length -
(0.9067- 0.9087 in)
19.989- 20.000 mm
19.93 mm
Reverse idler gear O.D. (0.78697- 0.78740
(0.7846 in)
in)
30.007- 30.020 mm
Reverse 25.07 mm
I.D. (1.18138- 1.18189
drive/driven gear (0.9870 in)
in)
Ring-to-gear clearance (ring 0.70- 1.49 mm 0.4 mm
5th synchro ring
pushed against gear) (0.028- 0.058 in) (0.016 in)
Ring-to-gear clearance (ring 0.73- 1.44 mm 0.4 mm
6th synchro ring
pushed against gear) (0.029- 0.056 in) (0.016 in)
Outer synchro ring-to-synchro
0.68- 1.19 mm 0.3 mm
cone clearance (ring pushed
(0.027- 0.046 in) (0.012 in)
against gear)
3rd double cone Synchro cone-to-gear clearance 0.48- 1.04 mm 0.3 mm
synchro (ring pushed against gear) (0.019- 0.040 in) (0.012 in)
Outer synchro ring-to-gear
0.95- 1.68 mm 0.6 mm
clearance (ring pushed against
(0.037- 0.066 in) (0.024 in)
gear)
Outer synchro ring-to-synchro
0.70- 1.19 mm 0.3 mm
cone clearance (ring pushed
(0.028- 0.046 in) (0.012 in)
against gear)
synchro (ring pushed against gear) (0.020- 0.044 in) (0.012 in)
Outer synchro ring-to-gear
0.95- 1.68 mm 0.6 mm
clearance (ring pushed against
(0.037- 0.066 in) (0.024 in)
gear)
Outer synchro ring-to-synchro
0.70- 1.19 mm 0.3 mm
cone clearance (ring pushed
(0.028- 0.046 in) (0.012 in)
against gear)
1st triple cone Synchro cone-to-gear clearance 0.70- 1.88 mm 0.3 mm
synchro (ring pushed against gear) (0.028- 0.074 in) (0.012 in)
Outer synchro ring-to-gear
1.12- 1.68 mm 0.6 mm
clearance (ring pushed against
(0.044- 0.066 in) (0.024 in)
gear)
Outer synchro ring-to-synchro
0.70- 1.19 mm 0.3 mm
cone clearance (ring pushed
(0.028- 0.046 in) (0.012 in)
against gear)
2nd triple cone Synchro cone-to-gear clearance 0.70- 1.88 mm 0.3 mm
synchro (ring pushed against gear) (0.028- 0.074 in) (0.012 in)
Outer synchro ring-to-gear
1.12- 1.68 mm 0.6 mm
clearance (ring pushed against
(0.044- 0.066 in) (0.024 in)
gear)
1st/2nd, 3rd/4th, 7.4- 7.6 mm (0.291 -
-
5th/6th 0.299 in)
Finger thickness
6.2- 6.4 mm (0.244-
Shift fork Reverse -
0.252 in)
0.35- 0.65 mm 1.0 mm
Fork-to-synchro sleeve clearance
(0.014- 0.025 in) (0.039 in)
6.50- 6.75 mm
Finger width -
(0.2559- 0.2657 in)
Shift lever-to-reverse shift piece 0- 0.4 mm (0- 0.015 0.5 mm
clearance in) (0.019 in)
Reverse shift lever
Shift lever width at contact area 13.0- 13.2 mm
-
(reverse shift piece side) (0.512- 0.520 in)
Shift lever-to-reverse shift fork 0.15- 0.60 mm 0.7 mm
clearance (0.006- 0.023 in) (0.027 in)
When worn
1st/2nd 26.1 mm (1.028 in)
or damaged
Detent ball spring Free length
When worn
3rd/4th, 5th/6th 27.4 mm (1.079 in)
or damaged
When worn
Steel ball Ball size 7.94 mm (0.3126 in)
or damaged
15.973- 16.005 mm
I.D. (0.62886- 0.63012 -
Shift arm in)
Shift arm-to-shift piece clearance 0.26- 0.57 mm 0.75 mm
manual
Tuesday, February 16, 2016 2:28:45 PM Page 13 2005 Mitchell Repair Information Company, LLC.
13
2012 Acura TL
2012 GENERAL INFORMATION Specifications - TL
in)
40.002- 40.018 mm
At transfer gear 39.95 mm
(1.57488- 1.57551
Diameter of transfer output shaft side in)
(1.5728 in)
(hypoid gear) at tapered roller
bearing contact area 31.975- 31.988 mm
At companion 31.92 mm
(1.25886- 1.25937
Transfer assembly flange side (1.2567 in)
in)
0.06- 0.16 mm
Transfer gear backlash Adjust
(0.0024- 0.0063 in)
2.64- 4.23 N.m
Tapered roller bearing total
(26.9- 43.1 kgf.cm, Adjust
starting torque (preload)
23.3- 37.4 lbf.in)
Capacity: Hypoid gear oil SAE Fluid change 0.43 L (0.45 US qt) -
Transfer assembly
90 viscosity, API classified GL 4
fluid Overhaul 0.45 L (0.48 US qt) -
or GL 5 only
Standard or
Item Measurement Qualification Service Limit
New
3.1 L (3.3 US
Fluid change -
Capacity: use Acura ATF DW- qt)
Automatic 1 (with SH-AWD) 7.8 L (8.2 US
transmission Overhaul -
qt)
fluid
Capacity: use Acura ATF DW- Fluid change 3.1 L (3.3US qt)
-
1 (without SH-AWD) Overhaul 7.1 L (7.5US qt)
-
Lower limit: 618
kPa (6.30
Line pressure (Low) (APP ATF temperature 667- 716 kPa
kgf/cm2 , 89.6 psi)
Sensor opening less than 25 % between 122F and (6.80- 7.30
Upper limit: 765
in D with Line Pressure Sol 212F (50C and kgf/cm2 , 96.7 -
kPa (7.80
VLV. A ON) 100C) 103.8 psi)
kgf/cm2 , 111.0
psi)
1, 164- 1, 285
kPa (11.87- 1, 079 kPa (11.00
At 2, 000 RPM in
Line pressure (Normal)
N or P 13.10 kgf/cm , kgf/cm2 , 156.5
2
168.8- 186.3 psi)
psi)
1, 123- 1, 172
kPa (11.45- 1, 079 kPa (11.00
At 2, 000 RPM in
1st clutch pressure
1st gear 11.95 kgf/cm , kgf/cm2 , 156.5
2
162.9- 170.0 psi)
psi)
1, 123- 1, 172
manual
Tuesday, February 16, 2016 2:28:45 PM Page 15 2005 Mitchell Repair Information Company, LLC.
15
2012 Acura TL
2012 GENERAL INFORMATION Specifications - TL
kPa (11.45-
1, 079 kPa (11.00
At 2, 000 RPM in 11.95 kgf/cm2 ,
2nd clutch pressure
2nd gear kgf/cm2 , 156.5
162.9- 170.0
psi)
psi)
1, 123- 1, 172
kPa (11.45- 1, 079 kPa (11.00
At 2, 000 RPM in
3rd clutch pressure
3rd gear 11.95 kgf/cm , kgf/cm2 , 156.5
2
162.9- 170.0 psi)
psi)
1, 123- 1, 172
kPa (11.45- 1, 079 kPa (11.00
At 2, 000 RPM in
4th clutch pressure
4th gear 11.95 kgf/cm , kgf/cm2 , 156.5
2
162.9- 170.0 psi)
ATF pressure psi)
1, 123- 1, 172
kPa (11.45- 1, 079 kPa (11.00
At 2, 000 RPM in
5th clutch pressure
5th gear 11.95 kgf/cm , kgf/cm2 , 156.5
2
162.9- 170.0 psi)
psi)
1, 123- 1, 172
kPa (11.45- 1, 079 kPa (11.00
At 2, 000 RPM in
6th clutch pressure
6th gear 11.95 kgf/cm , kgf/cm2 , 156.5
2
162.9- 170.0 psi)
psi)
At 4, 000 RPM in 294 kPa (3.00 245 kPa (2.50
Torque converter clutch
2nd gear (Lock-up kgf/cm2 , 42.7
pressure
condition) kgf/cm2 , 35.6 psi)
psi) or more
2, 000 RPM -
Torque Stall speed Check with vehicle
converter on level ground 1, 800- 2, 100
Service limit -
RPM
1.50- 1.70 mm
1st (0.0591 - 0.0669 -
in)
1.25- 1.45 mm
2nd (0.0492- 0.0571 -
in)
Clearance between clutch end- 1.25- 1.45 mm
Clutch 3rd (0.0492- 0.0571 -
plate and top disc
in)
1.50- 1.70 mm
4th (0.0591 - 0.0669 -
in)
in)
1.25- 1.45 mm
6th (0.0492- 0.0571 -
in)
31.984- 32.000
Diameter of stator shaft needle When worn or
mm (1.25921-
bearing contact area damaged
1.25984 in)
49.000- 49.016
When worn or
3rd gear I.D. mm (1.92913-
damaged
1.92976 in)
0.10- 0.21 mm
3rd gear axial clearance (0.0039- 0.0083 -
in)
41.962- 41.978
3rd gear collar diameter of When worn or
Mainshaft mm (1.65204-
needle bearing contact area damaged
1.65267 in)
29.00- 29.05
3rd gear collar width mm (1.1417- -
1.1437 in)
1.91- 1.96 mm
Sealing ring thickness (41 mm) (0.0752- 0.0772 -
in)
2.025- 2.060
Sealing ring groove width mm (0.07972- -
0.08110 in)
Diameter of needle bearing 40.505- 40.515
When worn or
contact area at torque converter mm (1.59468-
damaged
housing 1.59508 in)
57.000- 57.019
Diameter of 1st gear at needle When worn or
mm (2.24409-
bearing contact area damaged
2.24484 in)
52.971 - 52.990
Diameter of park gear at needle When worn or
mm (2.08547-
bearing contact area damaged
2.08622 in)
0.07- 0.30 mm
1st gear (0.0028- 0.0118 -
in)
Axial clearance of gears
0.04- 0.10 mm
2nd and 5th gear
(0.002- 0.003 -
(total)
in)
1.82 mm When worn or
A
(0.0717 in) damaged
1.86 mm When worn or
B
(0.0732 in) damaged
1.90 mm When worn or
manual
Tuesday, February 16, 2016 2:28:45 PM Page 17 2005 Mitchell Repair Information Company, LLC.
17
2012 Acura TL
2012 GENERAL INFORMATION Specifications - TL
manual
Tuesday, February 16, 2016 2:28:45 PM Page 18 2005 Mitchell Repair Information Company, LLC.
18
2012 Acura TL
2012 GENERAL INFORMATION Specifications - TL
0.05- 0.12 mm
2nd and 5th gear (0.002- 0.004 -
in)
37.975- 37.991
When worn or
2nd gear collar mm (1.49508-
damaged
Diameter of gear collars at 1.49571 in)
needle bearing contact area 44.962- 44.978
When worn or
5th gear collar mm (1.77015-
damaged
1.77078 in)
0.85 mm When worn or
A
(0.0335 in) damaged
0.92 mm When worn or
B
(0.0362 in) damaged
0.99 mm When worn or
C
(0.0390 in) damaged
1.06 mm When worn or
D
(0.0417 in) damaged
1.13 mm When worn or
E
(0.0445 in) damaged
1.20 mm When worn or
F
(0.0472 in) damaged
Secondary 1.27 mm When worn or
G
shaft (0.0500 in) damaged
1.34 mm When worn or
H
(0.0528 in) damaged
1.41 mm When worn or
I
Thrust shim thickness (89 mm) (0.0555 in) damaged
1.48 mm When worn or
J
(0.0583 in) damaged
1.55 mm When worn or
K
(0.0610 in) damaged
1.62 mm When worn or
L
(0.0638 in) damaged
1.69 mm When worn or
M
(0.0665 in) damaged
1.76 mm When worn or
N
(0.0693 in) damaged
1.83 mm When worn or
O
(0.0720 in) damaged
1.90 mm When worn or
P
(0.0748 in) damaged
1.97 mm When worn or
Q
(0.0776 in) damaged
2.04 mm When worn or
manual
Tuesday, February 16, 2016 2:28:45 PM Page 19 2005 Mitchell Repair Information Company, LLC.
19
2012 Acura TL
2012 GENERAL INFORMATION Specifications - TL
1.96913 in)
42.000- 42.016
When worn or
6th gear mm (1.65354-
damaged
I.D. of gears 1.65417 in)
41.000- 41.016
When worn or
Reverse gear mm (1.61417-
damaged
1.61480 in)
34.975- 34.991
Diameter of reverse gear collar When worn or
mm (1.37697-
at needle bearing contact area damaged
1.37760 in)
0.115- 0.350
4th gear mm (0.00453- -
0.01378 in)
0.045- 0.420
Axial clearance 6th gear mm (0.002- -
0.016 in)
0.1 - 0.2 mm
Reverse gear (0.004- 0.008 -
in)
51.50- 51.55
Reverse gear collar width mm (2.0276- -
2.0295 in)
Third shaft 2.99- 3.02 mm
Cotter thickness (0.1177- 0.1189 -
in)
1.90- 1.97 mm
Sealing ring thickness (35 mm) (0.0748- 0.0776 -
in)
2.025- 2.060
Sealing ring groove width mm (0.07972- -
0.08110 in)
51.60- 51.75
When worn or
Reverse selector hub O.D. mm (2.0315-
damaged
2.0374 in)
8.515 mm When worn or
A
(0.33524 in) damaged
8.540 mm When worn or
B
(0.33622 in) damaged
8.565 mm When worn or
C
4th gear washer thickness (0.33720 in) damaged
8.590 mm When worn or
D
(0.33819 in) damaged
8.615 mm When worn or
E
(0.33917 in) damaged
manual
Tuesday, February 16, 2016 2:28:45 PM Page 21 2005 Mitchell Repair Information Company, LLC.
21
2012 Acura TL
2012 GENERAL INFORMATION Specifications - TL
5.90- 6.00 mm
Reverse shift
Fork finger thickness (0.2323- 0.2362 5.4 mm (0.213 in)
fork
in)
Park gear and When worn or
- -
pawl damaged
14.000- 14.010
At shaft part mm (0.55118- -
Regulator I.D. of shift fork shaft contact 0.55157 in)
valve body area 37.000- 37.039
37.045 mm
At valve part mm (1.45669-
(1.45846 in)
1.45823 in)
35.000- 35.025
Main valve Third shaft sealing ring contact 35.05 mm (1.3799
mm (1.37795-
body I.D. in)
1.37893 in)
30.000- 30.021
ATF guide Secondary shaft sealing ring 30.05 mm (1.1831
mm (1.18110-
collar contact 1. D. in)
1.18193 in)
32.025- 32.055
Driveshaft/intermediate shaft
mm (1.26082- -
contact area I.D.
1.26201 in)
0.045- 0.096
Clearance between carrier and 0.13 mm (0.0051
mm (0.00177-
driveshaft in)
0.00378 in)
A/T 0.080- 0.126
Clearance between carrier and
differential mm (0.00315- -
intermediate shaft
carrier 0.00496 in)
3.9- 5.6 N.m
For new bearing (40- 57 kgf.cm, Adjust
Carrier bearing starting torque 35- 49 lbf.in)
(preload) 3.6- 5.3 N.m
For reused bearing (37- 54 kgf.cm, Adjust
32- 47 lbf.in)
0.05- 0.15 mm
Backlash (0.0020- 0.0059 -
in)
A/T 18.042- 18.066
differential I.D. mm (0.71031- -
pinion gear 0.71126 in)
0.055- 0.095
Clearance between pinion gear 0.12 mm (0.0047
mm (0.00217-
and pinion shaft in)
0.00374 in)
21.977- 21.990
At transmission 21.92 mm (0.8630
mm (0.86523-
Diameter of bearing contact area housing side 0.86575 in)
in)
40.002- 40.018
manual
Tuesday, February 16, 2016 2:28:46 PM Page 24 2005 Mitchell Repair Information Company, LLC.
24
2012 Acura TL
2012 GENERAL INFORMATION Specifications - TL
REAR DIFFERENTIAL
manual
Tuesday, February 16, 2016 2:28:46 PM Page 26 2005 Mitchell Repair Information Company, LLC.
26
2012 Acura TL
2012 GENERAL INFORMATION Specifications - TL
Standard or Service
Item Measurement Qualification
New Limit
2.53 L (2.67 US
Fluid change -
Rear differential Capacity: use Acura All-Wheel Drive qt)
fluid Fluid (DPSF) 2.77 L (2.93 US
Overhaul -
qt)
STEERING
Standard or Service
Item Measurement Qualification
New Limit
0- 10 mm (0-
Rotational play measured at outside edge -
Steering 0.39 in)
wheel Initial turning load measured at outside edge 29 N (3.0 kgf,
-
with engine running 6.6 lbf)
Angle of rack guide screw loosened from
Gearbox 10+5
locked position
SUSPENSION
BRAKES
AIR CONDITIONING
Service
Item Measurement Qualification Standard or New
Limit
Type HFC- 134a (R- 134a)
Refrigerant 505- 555 g (17.8- 19.6
Capacity of system -
oz)
DENSO ND- OIL 8 (P/N 38897-
Type
PR7- A01 AH)
Condenser (including dryer
35mL (1 1/5 fl.oz)
Refrigerant desiccant)
oil Evaporator 35mL (1 1/5 fl.oz)
Capacity of components
Each line and hose 10mL (1/3 fl.oz)
Dryer desiccant 10mL (1/3 fl.oz)
Compressor 70- 82 mL (2 3/8- 2 7/9 fl.oz)
Field coil resistance At 68F (20C) 3.9- 4.3 ohms
Compressor Pulley-to-pressure plate 0.35- 0.60 mm (0.014-
-
clearance 0.023 in)
TORQUE SUMMARY
manual
Tuesday, February 16, 2016 2:28:46 PM Page 28 2005 Mitchell Repair Information Company, LLC.
28
2012 Acura TL
2012 GENERAL INFORMATION Specifications - TL
TORQUE SPECIFICATIONS
NOTE: Refer to the appropriate Service information for the precautions and
complete procedures.
Refer to the appropriate Service information for the bolts/nuts not
indicated here.
Engine Electrical
Engine Mechanical
(2) Follow the S/M procedures closely for torque, sequence, and special steps.
NOTE: Refer to the appropriate Service information for the precautions and
complete procedures.
Refer to the appropriate Service information for the bolts/nuts not
indicated here.
Engine Cooling
Clutch
Manual Transmission
Automatic Transmission
NOTE: Refer to the appropriate Service information for the precautions and
complete procedures.
manual
Tuesday, February 16, 2016 2:28:46 PM Page 33 2005 Mitchell Repair Information Company, LLC.
33
2012 Acura TL
2012 GENERAL INFORMATION Specifications - TL
Rear Differential
Driveline/Axle
Steering
manual
Tuesday, February 16, 2016 2:28:46 PM Page 34 2005 Mitchell Repair Information Company, LLC.
34
2012 Acura TL
2012 GENERAL INFORMATION Specifications - TL
Suspension
Damper self-locking nut Use new nut 29 N.m (3.0 kgf.m, 22 lbf.ft)
Brakes
NOTE: Refer to the appropriate Service information for the precautions and
complete procedures.
Refer to the appropriate Service information for the bolts/nuts not
manual
Tuesday, February 16, 2016 2:28:46 PM Page 36 2005 Mitchell Repair Information Company, LLC.
36
2012 Acura TL
2012 GENERAL INFORMATION Specifications - TL
indicated here.
BODY
BODY ELECTRICAL
manual
Tuesday, February 16, 2016 2:28:46 PM Page 37 2005 Mitchell Repair Information Company, LLC.
37
2012 Acura TL
2012 GENERAL INFORMATION Specifications - TL
DESIGN SPECIFICATIONS
manual
Tuesday, February 16, 2016 2:28:46 PM Page 39 2005 Mitchell Repair Information Company, LLC.
39
2012 Acura TL
2012 GENERAL INFORMATION Specifications - TL
consumption at 68F
35 W maximum at 12 V
(20C)
Type HFC-134a (R-134a)
Refrigerant
Capacity 505- 555 g (17.8- 19.6 oz)
12 V- 65 Ah/20 HR (12V- 55
Battery
Ah/5 HR)
Under-hood fuse/relay 120 A, 70 A, 60 A, 50 A, 40 A, 30
box A, 20 A, 15 A, 10 A, 7.5 A
Driver's under-dash
20 A, 15 A, 10 A, 7.5 A
fuse/relay box
Fuses
Passenger's under-dash
20 A, 15 A, 10 A, 7.5 A
fuse/relay box
Auxiliary under-dash
7.5 A
fuse/relay box
Headlight high beam 12V- 60W (HB3)
Headlight low beam
12V- 35W (D2S)
(HID)
Fog lights 12V- 55W (H11)
Front turn
12 V- 24/2.2CP (Amber)
signal/parking lights
Side turn signal lights LED
Front side marker lights 12V- 3CP
ELECTRICAL Rear turn signal lights 12V- 21 W (Amber)
RATINGS Brake lights/taillights LED
Rear side marker lights 12V- 3CP
High mount brake light LED
Back-up lights 12V- 16W
Light bulbs License plate lights 12V- 5W
Ambient light LED
Trunk light 12V- 5W
Front individual map
LED
lights
Rear individual map
LED
lights
Door courtesy lights 12V- 3.4W
Glove box light 12V- 1.4W
Vanity mirror lights 12V- 2W
Gauge lights LED
Indicator lights LED
Console box light 12V- 1.4W
Footwell lights LED
manual
Tuesday, February 16, 2016 2:28:46 PM Page 41 2005 Mitchell Repair Information Company, LLC.
41
2012 Acura TL
2012 GENERAL INFORMATION Specifications - TL
BODY SPECIFICATIONS
manual
Tuesday, February 16, 2016 2:28:46 PM Page 42 2005 Mitchell Repair Information Company, LLC.
42