Professional Documents
Culture Documents
General Specfications
General Specfications
General Specfications
JOW CRUSHER
Working Principle
The belt and belt pulley are driven by a motor, and the movable jaw moves up and down via
eccentric shaft. The angle between fixed jaw and movable jaw becomes smaller when the
moving jaw runs down, then the materials are crushed into pieces. It becomes bigger when
the movable jaw runs up. The movable jaw plate leaves the fixed jaw plate under the action of
tension rod and spring, then the end products come out from the crushing cavity.
Features
1. Simple structure, convenient maintenance;
2. High crushing ratio, even output granularity;
3. High reliability, low investment;
4. Low noise, less dust.
Main Specifications
Grinding Wet Pan Mill /Gold grinding machine is the best equipment to replace ball mill.
because it have small investment, high output, low production cost, good efficiency and easy
installation. And the machine is the ideal beneficiation equipment for small and medium -sized
enterprise. Gold grinding machine is mainly used to process the gold, silver, lead, zinc, iron,
molybdenum, copper, antimony.The wet pan mill is named by the diameter of roller. 1300,
1350, 1400, 1500, 1600 is suitable for selection of iron ore, molybdenum ore ,lead ore ,zinc
ore, antimony ore and so on. 850, 900, 1000, 1100, 1200 is suitable for selection of gold
ore. Above all, 1200a type is the most popular and widely use .
Working Principle
The machine repeatedly squeeze and mill gold ore through the weight of the wheels until the gold
ore has been crushed completely. And then add 1 kg mercury into the water . Meantime, every 5-10
minutes, add gold ore to the machine. After 24 hours, recycle mercury. Then pack mercury with big
density of cloth. Twist the cloth and let the mercury come out. The gold will be left in the cloth.
SPECIFATIONS
ALL THE WHEELS ARE MADE FROM IRON MANGANIZE . ALL MOTORS AND GYRO BOXES
MADE IN GERMANY .
Ceramic grinder, Ceramic grinder mill, ceramic ball grinder
Ceramic grinder is mainly applied to the powder processing of mineral products in the
industries of metallurgy, construction materials, chemical, and mining, etc. Ceramic grinder
can produce powder from various non-flammable and non-explosive mineral materials with
Mohs hardness below 9.3 and humidity below 6%, such as barite, limestone, kaolnite, ceram
and slags, etc. The Product size is adjustable in the range of 80-425 mesh. Ceramic grinder is
possible to produce 30-80 mesh coarse powder through special device in the machine if
necessary.
FEATURE
1. High capacity.
2. Wide size range of final product (30 mesh-1000 mesh)
3. National dust-dump standard.
4. Easy to adjust separator.
5. Multi-class seals
Working Principle
ple
Materials spirally and evenly go into the first cabin of the grinding machine through the
feeding hollow shaft from the feeding device, and inside the first cabin, there are ladder lining
boards or ripple lining board in which there are many steel balls with different specificat ions.
The cylinder rotates and produces eccentric force to bring the steel balls to a certain height,
and then the steel balls will fall down to impact and grind the materials. After being coarsely
ground in the first cabin, the materials will go through t he single-layer partition board and into
the secondary cabin in which there are flat lining board, and in the lining board there are steel
balls to further grind the materials. Finally the powdery materials will be discharged from the
discharging grating bar to complete the powder grinding process.
TECHNICAL PARAMETERS
Max.
Power Weight
Model Rotate Speed (r/min) ball No Feed size(m) Output size(mm) Capacity(t/h)
(kw) (t)
(t)
MA600*900 40 0.2 0-15 0.075-0.3 0.1-0.5 3 0.5
MAQ7501800 39 1.0 0-15 0.075-0.3 0.3-0.8 11 3.5
MAQ9002100 37.8 1.5 0-15 0.075-0.3 0.8-2.1 15 5.2
DOUBLE JACKET , GERMAN MOTOR , BUILD FROM SPECIAL IRON
Knelson Gold Centrifugal Concentrator
SPECIFICATIONS
Gold mining equipment
1. High concentrating ratio and high recovery
2. Total process automation
3. steady recovery performan
FEATURE
1).High recovery rate
2).Easy to install
3).Easy to adjust
4).Easy to operat
5).No pollution
APPLICATION
It can be used not only for placer gold mining, but also for hard rock mining to recover the
natural gold, replacing amalgamation. It is also used to recover gold from the
oldtailings.. Structure & Working principle of Knelson Gold Centrifugal
ConcentratorFluidization water is introduced into the concentrate cone through a s eries of
fluidization holes.
Shaking table also named shaker table, gold mining table, gold mining concentration table,
gold mining separator equipment and concentrator table.
Shaking table is applicable for separations of fine-grained and micro-grained rare metal,
ferrous and non-ferrous metal, precious metal, coal and other minerals. It can carry out ore
concentration operation independently and also can operate in conjunction with jig, screw
separator, centrifugal separator and other equipment. The product is made by the only
manufacturer designated by the former Ministry of Geology and Mineral Resources, in
compliance with the Industrial standards.
Shaking Table is to make separations based on the difference of specific gravity of feed
materials, reciprocating asymmetrical movement and the stratification performance of the
inclined table surface in the lateral water flow with obvious zone of the minerals with different
specific gravities on the table, high quality of concentrates produced, convenient operation
and adjustment and other features.
The table surface is constructed of ore sand or slime and is made up of glass fibre reinforced
plastic or aluminum alloy.
glass steel shaking tables are effective gravity separation equipment which can be used for
different operation such as rough selection, elaborate selection and scavenging for large,
medium and small-sized factories and applies to the sorting of nonferrous metal, ferrous
metal, rare and precious metal, gold and nonmetallic ores of fine grains. Such shaking tables
are divided into ore sand tables and ore slime tables. Ore sand tables apply to the sorting of
coarse ores and ore slime tables apply to the sorting of fine ores.
Fine sand
Name Unit Course ore Deck Slime Deck
Deck
Length mm 4450 4450 4450
Deck Size transmission end width mm 1855 1855 1855
Concentrate end width mm 1546 1546 1546
Maximum Feeding Size mm 2 0.5 0.15
Feeding Amount t/d 30-60 10-20 15-25
Feeding Density % 25-30 20-25 15-25
Stroke mm 16-22 11-16 8-16
Frequency f 45-48 18-53 50-57
Water added t/d 80-150 30-60 10-17
Transverse slope of Deck 2 30-4 30 1 30-3 30 1 -2
Longitudinal slope of Deck 1.4 0.92 ------
Beneficiation Area m2 7.6 7.6 7.6
Cross-section Shape of Deck rectangular saw tooth triangle
Motor Power KW 1.1 1.1 1.1
Transmission Mechanism Eccentric linkage