Professional Documents
Culture Documents
2010 Datasheet DMV 22.5
2010 Datasheet DMV 22.5
DMV 22.5
DMV 22.5
In chloride environments:
Modulus of Elasticity (Chloride Stress Cracking - CSC)
Temperature 103 MPa 103 ksi Acetic acid The table below gives the results of stress
C (F) corrosion cracking tests after 500 hours in three
Acetic acid 80% T = 140C (284F) different boiling chloride solutions and with
20 (68) 200 29.0
Corrosion rate (mm/y) three kinds of test pieces: U bent, 4 point
100 (212) 195 28.3 bent-beam and C ring:
10
200 (392) 187 27.1
3 316 L
300 (572) 179 25.9 Test DMV 316L
1 DMV 928
piece 22.5
0.3
MgCI2 U bent (1) F F
0.1
DMV 22.5 45% 4 points (2) 100% 50%
0.03
boiling C ring (3) 25% 5%
3.5 Corrosion Properties 0.01 155C (310F)
0.003
0 200 400 600 800 1000 1200 CaCI2 U bent (1) F F
3.5.1 General Corrosion
CI - concentration (ppm) 50% 4 points (2) 100% 50%
The chemical composition of DMV 22.5 makes it
boiling C ring (3) 100% 50%
more resistant to corrosion than AISI 316L stain- 150C (302F)
less steel in many corrosive environments like: Mixture of acetic and formic acids
NaCI2 U bent (1) NF F
25% 4 points (2) 100% 50%
Sulphuric acid boiling C ring (3) 100% 50%
110C (230F)
Isocorrosion chart in sulphric acid
for 0.1 mm/year (4 mpy)
1. F = failure NF = no failure
Temp. (C) 2. 4 points bent-beam test - stress before
120 rupture (percentage of Y.S.)
Boiling 3. C ring test - stress before rupture
100
90
(percentage of Y.S.)
80
70
60 In H2S - Cl environments:
50 (Sulphide Stress Cracking - SSC)
40 Hydrochloric acid DMV 22.5 is an austenitic-ferritic stainless steel
316 L 316 L
30 Organic acids approved by NACE MR0175 / ISO 15156-3 for
50 100%
H2 SO4 use in sour environment. DMV 22.5 shows good
3.5.2 Intergranular Corrosion resistance to sulphide stress cracking corrosion
In the annealed condition, without any sensitization test at 24C (75.2F) and 90C (194F) over
treatment, corrosion rates in boiling nitric acid to 720 hours period (NACE TM0177) in CO2- H2S - Cl
ASTM A 262-C, remain below 1.1 mm/y media as indicated in the table below:
(6.1 m / 48h) which is equal to 3.7 mils / month.
After sensitization, DMV 22.5 meets the require-
SALZGITTER MANNESMANN STAINLESS TUBES
D A T A S H E E T
DMV 22.5
DMV 22.5
QUALITY IN ROUND TERMS.
Contact
Headquarters
Sales Contacts
Salzgitter Mannesmann Stainless Tubes Italia S.r.l. Salzgitter Mannesmann Stainless Tubes France SAS
Via Pi 30 Route de Semur
24062 Costa Volpino (BG) 21500 Montbard
Italy France
Tel.: +39 035 975 744 Tel.: +33 3 80 89 52 00
Fax: +39 035 975 803 Fax: +33 3 80 89 52 26
Email: salesitaly@smst-tubes.com Email: salesfrance@smst-tubes.com
Salzgitter Mannesmann Stainless Tubes Deutschland GmbH Salzgitter Mannesmann Stainless Tubes USA, Inc.
Wiesenstrae 36 12050 West Little York
45473 Mlheim an der Ruhr Houston Texas 77041
Germany USA
Tel.: +49 208 458 2611 Tel.: +1 713 466 7278
Fax: +49 208 458 2641 Fax: +1 713 466 3769
Email: salesgermany@smst-tubes.com Email: salesusa@smst-tubes.com
Whilst every care has been taken in compiling the technical information in this brochure, due to the continuing development and complex nature of the various factors used,
03/2010
it is given for information only. Our company cannot be held responsible for the information contained herein and our customers should carefully check for themselves where
necessary in order to make the appropriate selection, bearing in mind the conditions governing the fabrication of our alloys as well as the conditions in service. Information
held in this datasheet can be changed without notice.