Professional Documents
Culture Documents
BI3101A
BI3101A
BI3101A
Data Sheet
BI3101A
Version : 1.4
Notice
No part of this document may be copied or reproduced in any form or by any means without
the prior written consent of Beyond Innovation Technology Co., Ltd.
VDD + Latch
- - ON/OFF
+ +
+
Is s /10 Is s 1.5V 50K ohm
- -
PWM Comparator 2
SST Comparator
Error Amplifier 2 -
+ 2.25V
SST +
325mV
- 0.75V
SST
2.5V 2.25V
Band Gap Ramp Wave UVLO
+ 1.5V Reference 0.75V Generator 4.0V
SEL VDD
- 3.8V
Error Amplifier 1
RT
1.5V
- - PWM Comparator1
+
+ +
50K ohm -
VDD -
Latch
+
Csst Rsst
BI3101A when VSST > 2.5V to REFADJ: The reference voltage of error amplifier can
RT
prevent transformer be decided as a fixed level or variable levels. If the
working at extremely REFADJ pin is connected to a 0.47uF capacitor then
Rt
high voltage for a long 1.5FFixed Ref. to the ground
time. (means DC
-
1.5V + Error Amplifier 1(2)
+
DC/AC Characteristics:
Ramp wave
VSST
Vout (SST CMP)
Bi3101A provides two configurations to start the CCFL by SEL pin. One is a grounded SEL pin that makes Bi3101A
works just as the same as Bi3101. "Soft start" can be achieved by slowly increasing the reference voltage with the
embedded R-C circuit. But for some applications, it may need a long period and programmable of "soft start" to prevent the
inrush current during "Power On" sequence. Then a floating SEL pin enables the SST comparator of Bi3101A. With the
two inputs of the SST voltage and the internal ramp-wave, the output is a AND logic of the output of SST comparator and
the PWM comparator output. If a large capacitor of Csst is properly selected, a long and programmable "soft start period "
is obtained. Please refer to the Function Block Diagram. Fig.1 is the timing diagram of floating SEL .
Application Information:
Bi3101A provides engineer more possibilities while facing diversity of electronic system design. Four examples are here.
CN2
LV
HV
CN1 Example 1 :
1
VDD
BRIGHTNESS
2
3
This is a typical design for 2 to 4 lamps
ON/OFF
GND
4
system. ON/OFF control can turn off the
lamps without shout the VDD down.
CN3
HV
LV
16
15
14
13
12
11
10
9
SST
OLP2
ADJ2
VIN2
CMP2
SEL
OUT2
VDD
BI3101A
ON/OFF
CMP1
OUT1
OLP1
ADJ1
VIN1
GND
RT
1
2
3
4
5
6
7
8
VDD=12V +/-10%
BRIGHTNESS=DC 0~3.3V, 0V brightest dimming
ON/OFFGHigh active
Both of CN2 and CN3 may connect 1~2 CCFLs
CN3
HV
LV
16
15
14
13
12
11
10
9
SST
OLP2
ADJ2
VIN2
CMP2
SEL
OUT2
VDD
BI3101A
ON/OFF
CMP1
OUT1
OLP1
ADJ1
VIN1
GND
RT
1
2
3
4
5
6
7
8
VDD=12V +/-10%
BRIGHTNESS=DC 0~3.3V, 3.3V brightest dimming
ON/OFFGHigh active
Both of CN2 and CN3 may connect 1~2 CCFLs
CN2
LV
HV
Example 3 :
The independent design of open lamp
CN1 protection makes Bi3101A can used as a
VDD
1
2
single PWM controller without consuming
BRIGHTNESS
ON/OFF
3
4
the extra power. A force-to-GND
GND
connection of OLP pin will shut down the
circuit of PWM. This is an example of
Bi3101A operates as a single PWM
modulator.
16
15
14
13
12
11
10
9
SST
OLP2
ADJ2
VIN2
CMP2
SEL
OUT2
VDD
BI3101A
ON/OFF
CMP1
OUT1
OLP1
ADJ1
VIN1
GND
RT
1
2
3
4
5
6
7
8
VDD=12V +/-10%
BRIGHTNESS=DC 0~3.3V, 3.3V brightest dimming
ON/OFFGHigh active
CN2 may connect 1~2 CCFLs
CN2
LV
HV
Example 4 :
CN1
VDD 1
When a negative voltage is required in
BRIGHTNESS
ON/OFF
2
3 LCD display systems, this example is
GND 4
used for both CCFL control and
generating LCD negative bias.
16
15
14
13
12
11
10
9
SST
OLP2
ADJ2
VIN2
CMP2
SEL
OUT2
VDD
BI3101A
ON/OFF
CMP1
OUT1
OLP1
ADJ1
VIN1
GND
RT
1
2
3
4
5
6
7
8
1V
Negative Vout
VR
VDD=12V +/-10%
BRIGHTNESS=DC 0~3.3V, 3.3V brightest dimming
ON/OFFGHigh active
CN2 may connect 1~2 CCFLs
Negative Vout could be used as LCD contrast bias
Order Information:
Bi3101A-SO
SOP type packing
Part number
Beyond Innovation Technology Co., Ltd.
Bi3101A-DP
DIP type packing
Part number
Beyond Innovation Technology Co., Ltd.