Download as docx, pdf, or txt
Download as docx, pdf, or txt
You are on page 1of 21

1

Section A
[60 marks]
[60 markah]
Answer all questions in this section.
Jawab semua soalan dalam bahagian ini.

1 Diagram 1 shows a voltmeter which has two scales on it.


Rajah 1 menunjukkan sebuah voltmeter yang mempunyai dua skala di atasnya.

Diagram 1
Rajah 1
(a). State the physical quantity that can be measured by the voltmeter.
Nyatakan kuantiti fizik yang dapat disukat oleh sebuah voltmeter.

.
[1 mark]
(b) (i) What is the reading of the voltmeter when the terminal P and R is
connected?
Berapakah bacaan voltmeter bila terminal P dan R disambung ?


[1 mark]
(ii) What has to be done to the reading obtained in (b) (i) if the voltmeter has positive zero error?
Apakah yang perlu dibuat kepada bacaan yang didapati dalam (b) (i) jika voltmeter mempunyai
ralat sifar positif?


[1 mark]
(c) State the accuracy of the reading when the upper scale is used to make measurement.
Nyatakan kejituan bacaan apabila skala atas digunakan untuk membuat bacaan.


[1 mark]

2
2 Diagram 2shows a simple hydraulic system.
Rajah 2 menunjukkan satu sistem hidraulik ringkas

The area for the smaller piston is 0.1 m and the area for the bigger piston is 0.5 m The force acting on the
smaller piston is 20 N.
Luas permukaan bagi omboh kecil adalah 0.1 m luas permukaan bagi omboh yang besar adalah 0.5 m. Daya
yang dikenakan ke atas omboh kecil ialah 20N

(a) Name the principle used in the system above


Namakan prinsip yang digunakan didalam sistem diatas

..
[ 1 mark]
(b) Calculate the pressure applied to the oil
Hitung tekanan bertindak ke atas minyak

[ 1 mark]

(c) Calculate the output force exerted on the bigger piston


Hitung daya output yang bertindak keatas piston besar

[ 2 mark]
(d) What happens to the output force if the diameter of the output cylinder is greater?
Apakah yang akan berlaku kepada daya output jika diameter selinder output yang lebih besar
digunakan?

..

..
[ 1 mark]

3
3. Diagram 3.1 shows the car moving along a road PQRS. Diagram 3.2 shows how the speed of the car varies
with time as the car moves from P to S
Rajah 3.1 menunjukkan sebuah kereta bergerak sepanjang jalan PQRS. Rajah 3.2 menunjukkan bagaimana
laju kereta dengan masa semasa kereta bergerak dari P ke S

(a) Based on the graph in Diagram 3.2 describe the motion of the car from
Berdasarkan graf dalam Rajah 3.2 terangkan pergerakkan kereta dari
(i) P to Q

..

[ 1 mark]
(ii) Q to R

..

[ 1 mark]
(b) Calculate the acceleration of the car from R to S
Hitung pecutan kereta dari R ke S

[ 2 mark]

4
(c) Calculate the distance travelled by the car from R to S
Hitung jarak yang dilalui oleh kereta dari R ke S

[ 2 mark]
4 Diagram 4 shows a 12 V battery connected to a number of resistors.
Rajah 4 menunjukkan bateri 12V yang di sambungkan ke beberapa perintang

Diagram 4

(a) State the type of circuit connection for combined resistance of


Nyatakan jenis sambungan litar untuk gabungan perintang di
(i) the two 4 resistors
kedua-kedua perintang 4
..

(ii) the two 6 resistors


kedua-kedua perintang 6

[ 2 marks ]

(b) Calculate the current in the 5 resistor.


Hitung jumlah arus pada perintang 5

[ 2 marks ]

(c) The total current in the two 6 resistors is 4 A. Calculate the total power dissipated in the
resistors.
Jumlah arus pada perintang 6 ialah 4A. Hitungkan jumlah kuasa yang hilang pada perintang
tersebut

[ 2 marks ]

5
(d) The 5 resistor is made from a length of resistance wire of uniform cross-sectional area. State the
effect on the resistance of the wire if the same length of the same material with a smaller cross-
sectional area is used?
Perintang 5 diperbuat daripada perintang yang mempunyai rintangan keratin rentas yang sama.
Nyatakan kesan terhadap rintangan wayar sekiranya pangjang wayar yang sama daripada bahan
yang sama tetapi mempunyai keratan rentas yang lebih kecil digunakan

......................................................................................................................................................
[ 1 mark ]

5 Diagram 5.1 shows a concrete water tank filled with water.


Rajah 5.1 menunjukkan sebuah tangki konkrit yang diisi dengan air.

Diagram 5.1
Rajah 5.1

(a) State a factor that affects the water pressure in the tank.
Nyatakan satu faktor yang mempengaruhi tekanan air di dalam tangki.

...................................................................................................................................................
[1 mark]
(b) (i) Compare the water pressure at P and Q
Bandingkan tekanan air pada P dan Q

...........................................................................................................................................
[1 mark]
(ii) Calculate the water pressure at Q.
(Density of water = 1000 kg m-3 )
Hitungkan tekanan air pada Q
(Ketumpatan air = 1000 kg m-3)

[2 marks]

6
(c) Diagram 5.2 shows water flows from the concrete tank to the house water tank.
Rajah 5.2 menunjukkan air mengalir dari tangki konkrit ke tangki air di rumah.

Diagram 5.2
Rajah 5.2
(i) What is the factor that causes the water to flow from the concrete tank to the
water tank in the house?
Apakah faktor yang menyebabkan air boleh mengalir dari tangki konkrit ke tangki air di
rumah?

.............................................................................................................................................
[1 mark]
(ii) The flow of water from the concrete tank to the house will stop at level P.
Explain why the supply stops?
Pengaliran air dari tangki konkrit ke tangki air di rumah akan terhenti pada paras P.
Terangkan mengapa pengalirannya berhenti?
..........................................................................................................................................

...........................................................................................................................................
[2 mark]

(d) Draw a water tank that can withstand high water pressure .
Lukiskan tangki air yang boleh menampung tekanan yang tinggi.

[1 mark]
6 (a) Diagram 6.1 shows an ideal transformer.

240 12
V V

Primary coil Secondary coil

Gegelung Gegelung

7
(i) Name the type of transformer.
Namakan jenis transformer

..
[1 mark]

(ii) Explain how current is induced in the secondary coil?


Huraikan bagaimana arus teraruh didalam gelung sekunder

..................................................................................................................................

..................................................................................................................................

[3 marks]
(b) Rajah 6.2. shows a circuit consisting of a transformer, an ammeter and two light bulbs. The
ammeter reading is 0.5 A and both bulbs light up with normal brightness.
Rajah 6.2 menunjukkan litar yang mengandungi transformer, ammeter dan dua mentol. Bacaan
ammeter ialah 0.5A, kedua-dua mentol menyala dengan kecerahanyang normal

DIAGRAM 6.2

(i) What is the output voltage of the transformer?


Apakah voltan output bagi transformer?

[2 marks]

(ii) Calculate the efficiency of the transformer.


Hitung kecekapan transformer

[2 marks]

8
7 Diagram 7.1 shows the arrangement of the apparatus to determine the specific heat capacity of an aluminium
block mass 1.0 kg. The thermometer reading is recorded when it reached thermal equilibirium with the
aluminium block .
Rajah 7.1 menunjukkan susunan radas untuk menentukan muatan haba tentu bagi satu bongkah aluminium
berjisim 1.0kg. bacaan termometer direkod apabila ia mencapai keseimbangan termal dengan bonhkah
aluminium

(a) (i) What is the meaning of thermal equilibirium ?


Apakah maksud kesimbangan terma?

..
[1 mark]
(b) Explain how a thermal equilibirium is achieved between the aluminium block and the thermometer.
Terangkan bagaimana keseimbangan terma dicapai antara blok aluminium dan termometer

..

..

..
[3 mark]
(c) The immersion heater supplied 27kJ of energy to the aluminium block. The temperature rise is 25
Pemanas rendam membekalkan 27kJ tenaga kepada bongkah aluminium. Kenaikan suhu ialah 25

Calculate the specific heat capacity of the aluminium block


Hitungkan muatan haba tentu blok aluminium

[2 mark]

9
The value of specific heay capacity obtained in (c) is higher than the actual value.
Some modifications need to be done to the material of the wrapper and the wall of the glass bulb to increase the
accuracy of the temperature reading.
State the suitable modification and give one reason for the modificatioan
Nilai muatan haba tentu yang dipero;ehi dalam (c) lebih besar daripada nilai sebenar. Beberapa
pengubahsuaian peerlu dilakukan kepada bahan pembalut dan dinding bebuli kaca untuk menambah kejituan
bacaan suhu.
Nyatakan pengubahsuaian yang sesuai dan berikan satu sebab untuk pengubahsuaian itu

(i) Type of insulation material x


Jenis bahan bagi bahan penebat X

..

Reason:
Sebab:

..
[2 mark]

(ii) Thickness of the glass bulbs wall

..

Reason:
Sebab:

..
[2 mark]

8 Diagram 8 shows one bulb connected to one dry cell.


Rajah 8 menunjukkan satu mentol disambungkan kepada satu sel kering.

Diagram 8
Rajah 8
(a) What is meant by the label 9V, 20W on the bulb?
Apakah yang dimaksudkan dengan label 9 V, 20W pada mentol itu?

...............................................................................................................................
[ 1 mark ]

10
(b) Based on Diagram 8, calculate
Berdasarkan Rajah 8, hitungkan
(i) current flowing through the bulb.
arus mengalir melalui mentol.

[2 marks]
(ii) resistance of the filament of the bulb?
rintangan bagi filamen mentol tersebut?

[2 marks]
(c) Table 8.1 shows three different types of filament to be used in bulb in Diagram 8 above.
Jadual 8.1 menunjukkan tiga jenis filamen berbeza yang akan digunakan di dalam mentol pada
Rajah 8 diatas.

Table 8.1
Jadual 8.1
(i) State the effect of thickness of wire of the filament to the rate of energy loss in the filament.
Nyatakan kesan ketebalan dawai filamen terhadap kadar kehilangan tenaga pada filamen.

...........
[1 mark]
(ii) Calculate the efficiency of each filaments P,Q, and R.
Hitungkan kecekapan setiap filamen P,Q dan R.

[4 marks]

11
(iii) Suggest the most suitable filament to be used in the bulb. Justify your choice.
Cadangkan filamen yang paling sesuai digunakan di dalam mentol. Berikan alasan bagi pilihan anda
itu

...................
...................
[2 marks]
9 Diagram 9.9 and Diagram 9.2 shows two electrical circuits containing semiconductor diodes.
Rajah 9.9 dan 9.2 menunjukkan dua litar elektrik yang mengandungi diod semikonduktor.

Diagram 1.1 Diagram 1.2


Rajah 1.1 Rajah 1.2

a) What is meant by semiconductor?


Apakah yang dimasudkan dengan semikonduktor.

[ 1 mark]

b) Using Diagram 9.9 and Diagram 9.2 ,


Menggunakan Rajah 9.9 dan Rajah 9.2,

i) compare the lighting of the bulb.


bandingkan nyalaan mentol
[ 1 markah]

ii) compare the electric current flow.


bandingkan pengaliran arus elektrik.
[1 markah]

iii) compare the connection of the diodes to the terminal of the battery.
bandingkan sambungan diod ke terminal bateri
[ 1 mark/ 1 markah]

iv) relate the connection of the diodes to the terminal of the battery and the lighting of the bulb.

hubungkaitkan sambungan diod ke terminal bateri dengan nyalaan mentol .

[1 mark/ 1 markah]

v) deduce a relevant physics concept.


deduksikan satu konsep fizik yang relevant [1 mark/1 markah]

12
c) Diagram 9.3 shows a full wave rectifier circuit.
Rajah 9.3 menunjukkan litar rektifikasi gelombang penuh.

input

output

Diagram 9.3
Rajah 9.3

i) Draw the wave front form of a full wave rectification


Lukis bentuk gelombang bagi rektifikasi gelombang penuh.

[1 mark/ 1 markah]

ii) A capacitor is placed across the output to smooth the current.


Draw the wave front produced.
Explain how capacitor works to smooth the current.
Sebuah kapasitor diletakkan merentasi output untuk meratakan arus dalam litar itu.
Lukiskan bentuk gelombang yang dihasilkan.
Jelaskan bagaimana kapasitor berfungsi untuk meratakan arus.

[4 marks/ 4 markah]

d) Diagram 9.4 shows a circuit with a transistor that acts as an automatic switch.
Rajah 9.4 menunjukkan litar yang mengandungi transistor yang bertindak sebagai suiz automatik.

R1
6V R2

Diagram 9.4
Rajah 9.4

13
The transistor in the circuit causes the light emitting diod (LDR) to light up when it is dark. A
technician wants a fan labelled 240V,900W in a room to be automatically switched on when the
room is hot.

Transistor dalam litar menyebabkan diod pemancar cahaya menyala apabila keadaan gelap.
Seorang juruteknik ingin sebuah kipas berlabel 240V,900W di sebuah bilik dihidupkan apabila
bilik itu panas.

Suggest modification that can be made to the circuit in Diagram 9.4 so that the fan can be
switched on when the room is hot.
Draw the modification.

Cadangkan pengubahsuaian yang boleh dilakukan pada litar dalam Rajah 9.4 untuk
membolehkan kipas itu dihidupkan secara automatik apabila bilik itu panas.
Lukis litar yang diubahsuai itu.

State and explain the modifications based on the following aspects:


Nyatakan dan beri penerangan tentang pengubahsuaian itu berdasarkan aspek-aspek berikut:

i) the electrical components that are needed to replace the LED and LDR
komponen-komponen elektrik yang perlu untuk menggantikan LED dan LDR.

ii) the position of the electrical component


kedudukan komponen-komponen elektrik dalam litar itu.

[10 mark/ 10 markah]

10 (a) Diagram 10.1 and Diagram 10.2 shows two identical electromagnet, X and Y .
Rajah 10.1 dan Rajah 10.2 menunjukkan dua elektromagnet yang serupa, X dan Y.

Diagram 10.1 Diagram 10.2


Rajah 10.1 Rajah 10.2

(i) What is meant by electromagnet?


Apakah yang dimaksudkan dengan elektromagnet?
[ 1 mark ]

(ii) Using Diagram 10.1 and Diagram 10.2 compare the current flow, the amount of
iron filing and the magnetic field strength of the two electrodes. Relate the current

14
flow and amount of iron filing attracted by the electromagnet and the magnetic field
strength.
Menggunakan Rajah 10.1 dan Rajah 10.2 bandingkan pengaliran arus, kuantiti serbuk besi
dan kekuatan medan magnet kedua-dua elektrod. Hubungkait pengaliran arus dengan kuantiti
serbuk besi yang tertarik kepada elektromagnet dan kekuatan medan magnet.
[ 5 marks ]
(b) Diagram 10.3 shows a circuit breaker.
Rajah 10.3 menunjukkan sebuah pemutus litar.

Diagram 10.3
Rajah 10.3

Explain how the circuit breaker works.


Terangkan bagaimana pemutus litar berfungsi.
[ 4 marks]

(c) Diagram 10.4 shows an a.c generator


Rajah 10.4 menunjukkan sebuah penjana a.u

Diagram10.4
Rajah 10.4

15
(i) Explain how the generator works to produce alternating current.
Terangkan bagaimana penjana berfungsi untuk menghasilkan arus ulang alik.
[ 4 marks ]

(ii) Explain the modification that needs to be done on the generator and the external
circuit to enable the generator to be a d.c generator and produce more current.
Terangkan pengubahsuain yang perlu dibuat kepada penjana dan litar luar untuk membolehkan
penjana menjadi penjana a.t dan menghasilkan arus yang lebih tinggi.

[6 marks]

11 Diagram 11.1 shows spring X and spring Y that are used in a suspension system of a
motorcycle. Both springs are of the same material and length but have different spring
constant, k
Rajah 11.1 menunjukkan spring X dan spring Y yang digunakan dalam sistem suspensi
sebuah motosikal. Kedua-dua spring itu dibuat dari bahan dan panjang yang sama tetapi
mempunyai pemalar spring,k yang berbeza

Diagram 11.1 /Rajah 11.1


(a) What is the meaning of spring constant?
Apakah yang dimaksudkan dengan pemalar spring?
[1 mark/markah]
(b) Based on Diagram 11.1,
Berdasarkan Rajah 11.1,
(i) Which spring has the higher spring constant, k ?
Spring yang manakah mempunyai pemalar spring, k yang lebih tinggi?
[1 mark/markah]
(ii) Explain your answer in (b) (i).
Terangkan jawapan anda dalam (b) (i).
[4 marks]

16
(c) Table 11 shows the characteristics of four types of spring to be used in a suspension
system of a motorcycle.
Jadual 11 menunjukkan ciri-ciri bagi empat jenis spring yang akan digunakan dalam sistem
suspensi pada sebuah motorsikal.

17
Study the characteristics of all the four spring based on the following aspects:
Kaji ciri-ciri keempat-empat spring tersebut berdasarkan aspek-aspek berikut:
(i) The diameter of the spring / Diameter spring
(ii) The elastic limit of the spring / Had kenyal spring
(iii) The spring constant / Pemalar spring
(iv) The natural frequency / Frekuensi asli
Explain the suitability of each aspects and then determine the most suitable spring to be used in the
suspension system of a motorcycle.
Give a reason for your choice.
Terangkan kesesuaian setiap aspek dan seterusnya tentukan spring yang paling sesuai untuk digunakan
dalam sistem suspensi sebuah motorsikal.
Beri sebab untuk pilihan anda.
[10 marks/markah]

(d) Diagram 11.2 shows the original length of a spring is 20 cm. Diagram 11.3 shows the
length of the spring is 26 cm when a load of mass 300g is attached to it .
Rajah 11.2 menunjukkan panjang asal bagi satu spring adalah 20 cm. Rajah 11.3
menunjukkan panjang spring menjadi 26 cm apabila satu beban 300 g digantung di
bawahnya.

Calculate / Hitungkan:
(i) the spring constant of the spring
pemalar spring bagi spring tersebut
[2 marks/markah]
(ii) the new length of the spring when a load of 500 g is attached to the spring.
panjang baru spring apabila beban 500 g di gantung kepada spring itu.
[2 marks/markah]

18
12 Diagram 12.1 shows a system used in a factory to ensure the volume of guava juice in a bottle
is uniform.
Rajah 12.1 menunjukkan satu sistem yang digunakan di sebuah kilang untuk memastikan
isipadu jus buah jambu yang diisi ke dalam botol adalah seragam.

Guava juice

Jus buah jambu

Diagram 12.1
Rajah 12.1

The radioactive source, radiation detector and counter are used to detect the volume of guava
juice. The radioactive source contains a radioisotope.
Sumber radioaktif, pengesan sinaran dan pembilang digunakan untuk mengesan isipadu jus
buah jambu. Sumber radioaktif itu mengandungi radioisotop.

(a) What is meant by a radioisotope?


Apakah yang dimaksudkan dengan radioisotop?
[1 mark]
(b) Table 12.2 shows the characteristics of five radioisotopes P, Q, R, S and T.
Jadual 12.2 menunjukkan ciri-ciri bagi lima radioisotop P, Q, R, S dan T.
Radioisotope
Half life Types of ray State of matter Ionising power
Radioisotop
Separuh hayat Jenis sinar Keadaan jirim Kuasa pengionan

P 7 hours alfa solid high


7 jam pepejal tinggi

Q 10 days beta liquid moderate


10 hari cecair sederhana

R 100 days gamma solid low


100 hari pepejal rendah

19
S 10 years gamma liquid high
10 tahun cecair tinggi

T 30 years beta solid low


30 tahun pepejal rendah

Table 12.2
Jadual 12.2

As a factory engineer, you are required to determine the most suitable radioisotope that
can be used by the system to ensure the volume of guava juice is uniform.
Study the characteristics of all 5 radioisotopes and explain the suitability of the aspects.
Determine the most suitable radioisotope and give the reason for your choice.

Sebagai jurutera kilang, anda dikehendaki menentukan radioisotop yang paling sesuai yang boleh
digunakan oleh sistem untuk memastikan isipadu jus buah jambu adalah seragam.
Kaji ciri-ciri kelima-lima radioisotop dan terangkan kesesuaian bagi setiap aspek. Tentukan
radioisotop yang paling sesuai dan beri sebab bagi pilihan anda.
[10 marks]

(c) Table 12.3 shows the reading of the rate meter for 6 bottles through detector and radioactive source .
Jadual 12.3 menunjukkan bacaan meter kadar bagi 6 botol yang melalui pengesan dan sumber
radioaktif.

Bottle/Botol
A B C D E F

Rate meter reading/Bacaan


meter kadar
464 468 467 462 568 470
(count per minute/Bilangan
per minit)

Table 12.3
Jadual 12.3

(i) State one detector that is suitable to be used for this purpose.
Nyatakan satu alat pengesan yang sesuai digunakan untuk tujuan ini.
[ 1 mark]

(ii) Based on table 12.3, which bottle shows the least volume of juice and state the reason for your
answer.
Berdasarkan jadual 12.3, botol yang manakah menunjukkan isipadu yang tidak cukup dan
nyatakan sebab bagi jawapan anda.
[3 marks]

(d) In a radioactive decay series, Uranium-238 decays to become Radium-226 by

20
emitting alfa and beta.
Dalam siri reputan radioaktif, Uranium-238 mereput menjadi Radium-226 dengan menghasilkan
alfa dan beta.

+ X + Y

Determine the values of X and Y?


Tentukan nilai X dan Y?
[5 marks]

END OF QUESTION PAPER


KERTAS SOALAN TAMAT

21

You might also like