Professional Documents
Culture Documents
LM393N PDF
LM393N PDF
LM2903V, NCV2903
Output Voltage Compatible with DTL, ECL, TTL, MOS, and CMOS
Logic Levels
PIN CONNECTIONS
ESD Clamps on the Inputs Increase the Ruggedness of the Device
without Affecting Performance Output A 1 8 VCC
NCV Prefix for Automotive and Other Applications Requiring Site 2
7 Output B
Inputs A +
and Control Changes 3
6
Inputs B
+ 5
PbFree Packages are Available GND 4
(Top View)
VCC + Input Input Output
F1
Q10
Q1 Q9 Q16
Q8 Q12
Q2 Q15
Q11
R1
4.6 k
MAXIMUM RATINGS
Rating Symbol Value Unit
Power Supply Voltage VCC +36 or 18 Vdc
Input Differential Voltage Range VIDR 36 Vdc
Input Common Mode Voltage Range VICR 0.3 to +36 Vdc
Output Short CircuittoGround ISC Continuous mA
Output Sink Current (Note 1) ISink 20
Power Dissipation @ TA = 25C PD 570 mW
Derate above 25C 1/RJA 5.7 mW/C
Operating Ambient Temperature Range TA C
LM293 25 to +85
LM393 0 to +70
LM2903 40 to +105
LM2903V, NCV2903 (Note 2) 40 to +125
Maximum ratings are those values beyond which device damage can occur. Maximum ratings applied to the device are individual stress limit
values (not normal operating conditions) and are not valid simultaneously. If these limits are exceeded, device functional operation is not implied,
damage may occur and reliability may be affected.
1. The maximum output current may be as high as 20 mA, independent of the magnitude of VCC, output short circuits to VCC can cause
excessive heating and eventual destruction.
2. NCV2903 is qualified for automotive use.
http://onsemi.com
2
LM393, LM293, LM2903, LM2903V, NCV2903
ELECTRICAL CHARACTERISTICS (VCC = 5.0 Vdc, Tlow TA Thigh, unless otherwise noted.)
LM2903, LM2903V,
LM293, LM393 NCV2903
http://onsemi.com
3
LM393, LM293, LM2903, LM2903V, NCV2903
LM293/393 LM2903
80 80
TA = 40 C
IIB , INPUT BIAS CURRENT (nA)
70
0 0
0 5.0 10 15 20 25 30 35 40 0 5.0 10 15 20 25 30 35 40
VCC, SUPPLY VOLTAGE (Vdc) VCC, SUPPLY VOLTAGE (Vdc)
Figure 2. Input Bias Current versus Figure 3. Input Bias Current versus
Power Supply Voltage Power Supply Voltage
10 10
Out of Out of
VOL , SATURATION VOLTAGE (Vdc)
1.0 1.0
TA = +125C
TA = +85 C
0.1 0.1
TA = +25 C TA = 55 C TA = +25 C
0.01 0.01
TA = 0 C
TA = 40 C
0.001 0.001
0.01 0.1 1.0 10 100 0.01 0.1 1.0 10 100
ISink, OUTPUT SINK CURRENT (mA) ISink, OUTPUT SINK CURRENT (mA)
1.0
TA = 55 C TA = 40 C
ICC , SUPPLY CURRENT (mA)
1.2
ICC , SUPPLY CURRENT (mA)
0.8 TA = 0 C
TA = +25 C TA = 0 C
1.0
TA = +25 C
0.6
TA = +70 C 0.8
0.4 TA = +125C
TA = +85 C
0.6
0.2
RL = RL =
0.4
0
5.0 10 15 20 25 30 35 40 0 5.0 10 15 20 25 30 35 40
VCC, SUPPLY VOLTAGE (Vdc) VCC, SUPPLY VOLTAGE (Vdc)
Figure 6. Power Supply Current versus Figure 7. Power Supply Current versus
Power Supply Voltage Power Supply Voltage
http://onsemi.com
4
LM393, LM293, LM2903, LM2903V, NCV2903
APPLICATIONS INFORMATION
These dual comparators feature high gain, wide The addition of positive feedback (< 10 mV) is also
bandwidth characteristics. This gives the device oscillation recommended. It is good design practice to ground all
tendencies if the outputs are capacitively coupled to the unused pins.
inputs via stray capacitance. This oscillation manifests itself Differential input voltages may be larger than supply
during output transitions (VOL to VOH). To alleviate this voltage without damaging the comparators inputs. Voltages
situation, input resistors < 10 k should be used. more negative than 0.3 V should not be used.
+15 V
R1 R4 R5 Vin(min)
220 k 220 k 10 k Vin
8.2 k
Vin
R1 6.8 k LM393
+VCC
D1 R2
10 k
15 k 10 M LM393
Vin VCC
R3
VO
D1 prevents input from going negative by more than 0.6 V. VEE
R1 + R2 = R3
VEE
R5
R3 for small error in zero crossing.
10 Vin(min) 0.4 V peak for 1% phase distortion ().
VCC VCC
1.0 M t R RL
VCC
RL LM393 LM393
10 k + VC C + VO
VCC 0.001 F LM393
VO
+ + Vref
51 k
ON for t tO + t
where: Vin Vref
51 k VCC Vref 0
51 k t = RC n ( ) VO
VCC
VO 0
VC Vref
0 0
t tO t
Figure 10. FreeRunning SquareWave Oscillator Figure 11. Time Delay Generator
VCC
RS = R1 | | R2
RS RL
(VCC Vref) R1
Vth1 = Vref +
LM393 R1 + R2 + RL
+
(Vref VO Low) R1
Vth2 = Vref
R1 R1 + R2
Vref
R2
http://onsemi.com
5
LM393, LM293, LM2903, LM2903V, NCV2903
MARKING DIAGRAMS
PDIP8 Micro8
N SUFFIX DM SUFFIX
CASE 626 CASE 846A
8 8
8 8
LM393N LM2903N x93 2903
AWL AWL
YYWW YYWW AYW AYW
1 1
1 1
SOIC8
D SUFFIX
CASE 751
8 8 8
LMx93 2903 2903V
ALYW ALYW ALYW
*
1 1 1
x = 2 or 3
A = Assembly Location
WL, L = Wafer Lot
YY, Y = Year
WW, W = Work Week
*This marking diagram also applies to NCV2903DR2.
http://onsemi.com
6
LM393, LM293, LM2903, LM2903V, NCV2903
ORDERING INFORMATION
Device Package Shipping
LM293D SOIC8 98 Units / Rail
LM293DR2 SOIC8 2500 Units / Reel
LM293DR2G SOIC8
(PbFree)
http://onsemi.com
7
LM393, LM293, LM2903, LM2903V, NCV2903
PACKAGE DIMENSIONS
PDIP8
N SUFFIX
CASE 62605
ISSUE L
NOTES:
1. DIMENSION L TO CENTER OF LEAD WHEN
FORMED PARALLEL.
8 5 2. PACKAGE CONTOUR OPTIONAL (ROUND OR
SQUARE CORNERS).
3. DIMENSIONING AND TOLERANCING PER ANSI
B Y14.5M, 1982.
1 4 MILLIMETERS INCHES
DIM MIN MAX MIN MAX
A 9.40 10.16 0.370 0.400
B 6.10 6.60 0.240 0.260
F C 3.94 4.45 0.155 0.175
D 0.38 0.51 0.015 0.020
NOTE 2 A F 1.02 1.78 0.040 0.070
L G 2.54 BSC 0.100 BSC
H 0.76 1.27 0.030 0.050
J 0.20 0.30 0.008 0.012
K 2.92 3.43 0.115 0.135
C L 7.62 BSC 0.300 BSC
M 10 10
J N 0.76 1.01 0.030 0.040
T
SEATING N
PLANE
M
D K
H G
0.13 (0.005) M T A M B M
http://onsemi.com
8
LM393, LM293, LM2903, LM2903V, NCV2903
SOIC8
D SUFFIX
CASE 75107
ISSUE AC
NOTES:
X 1. DIMENSIONING AND TOLERANCING PER
A ANSI Y14.5M, 1982.
2. CONTROLLING DIMENSION: MILLIMETER.
3. DIMENSION A AND B DO NOT INCLUDE
MOLD PROTRUSION.
8 5 4. MAXIMUM MOLD PROTRUSION 0.15 (0.006)
PER SIDE.
B S 0.25 (0.010) M Y M 5. DIMENSION D DOES NOT INCLUDE DAMBAR
PROTRUSION. ALLOWABLE DAMBAR
1 PROTRUSION SHALL BE 0.127 (0.005) TOTAL
4 IN EXCESS OF THE D DIMENSION AT
Y K MAXIMUM MATERIAL CONDITION.
6. 75101 THRU 75106 ARE OBSOLETE. NEW
STANDARD IS 75107.
G
MILLIMETERS INCHES
C N X 45 DIM MIN MAX MIN MAX
A 4.80 5.00 0.189 0.197
SEATING B 3.80 4.00 0.150 0.157
PLANE
C 1.35 1.75 0.053 0.069
Z D 0.33 0.51 0.013 0.020
0.10 (0.004) G 1.27 BSC 0.050 BSC
M H 0.10 0.25 0.004 0.010
H D J J 0.19 0.25 0.007 0.010
K 0.40 1.27 0.016 0.050
M 0 8 0 8
0.25 (0.010) M Z Y S X S N 0.25 0.50 0.010 0.020
S 5.80 6.20 0.228 0.244
SOLDERING FOOTPRINT*
1.52
0.060
7.0 4.0
0.275 0.155
0.6 1.270
0.024 0.050
http://onsemi.com
9
LM393, LM293, LM2903, LM2903V, NCV2903
PACKAGE DIMENSIONS
Micro8
DM SUFFIX
CASE 846A02
ISSUE F
NOTES:
A 1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: MILLIMETER.
3. DIMENSION A DOES NOT INCLUDE MOLD FLASH,
PROTRUSIONS OR GATE BURRS. MOLD FLASH,
PROTRUSIONS OR GATE BURRS SHALL NOT
K B EXCEED 0.15 (0.006) PER SIDE.
4. DIMENSION B DOES NOT INCLUDE INTERLEAD
FLASH OR PROTRUSION. INTERLEAD FLASH OR
PROTRUSION SHALL NOT EXCEED 0.25 (0.010)
PER SIDE.
5. 846A01 OBSOLETE, NEW STANDARD 846A02.
PIN 1 ID
G
D 8 PL MILLIMETERS INCHES
DIM MIN MAX MIN MAX
0.08 (0.003) M T B S A S A 2.90 3.10 0.114 0.122
B 2.90 3.10 0.114 0.122
C 1.10 0.043
D 0.25 0.40 0.010 0.016
SEATING G 0.65 BSC 0.026 BSC
T PLANE H 0.05 0.15 0.002 0.006
C J 0.13 0.23 0.005 0.009
0.038 (0.0015) K 4.75 5.05 0.187 0.199
L 0.40 0.70 0.016 0.028
J L
H
SOLDERING FOOTPRINT*
1.04 0.38
8X 8X
0.041 0.015
0.65
6X
0.0256 SCALE 8:1 inches
mm
ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice
to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability
arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages.
Typical parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All
operating parameters, including Typicals must be validated for each customer application by customers technical experts. SCILLC does not convey any license under its patent rights
nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications
intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should
Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates,
and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death
associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal
Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
http://onsemi.com LM393/D
10