Professional Documents
Culture Documents
IBwave Design Release Notes 8.1.2
IBwave Design Release Notes 8.1.2
2
iBwave Solutions Inc.
The information contained herein is the property of iBwave Solutions and is strictly confidential. Except as
expressly authorized in writing by iBwave Solutions, the holder shall keep all information confidential,
shall disclose it only to its employees with a need to know, and shall protect it, in whole or in part, from
disclosure and dissemination to third parties with the same degree of care protect its own confidential
information, but with no less than reasonable care. Except as expressly authorized in writing by iBwave
Solutions, the holder is granted no rights to use the information herein. Information is subject to change
without notice. iBwave Solutions reserves the right to make changes in design or components as
progress in engineering and manufacturing may warrant.
Other Enhancements................................................................................................................................ 7
NEXT STEPS.............................................................................................................................................. 18
Support for simultaneous Wi-Fi Active and Passive survey collection during a walk
Other improvements
1
Enhanced Capacity Analysis and Calculations
Subscriber service
Market share
Default capacity definitions sets the values for market share usage profile and subscriber service.
2
WHATS NEW IN VERSION 8.0?
Set the capacity expected peak traffic in zones on the floor plan.
3
Enhanced Capacity Analysis and Calculations
Cell load
Equipment limits
others
A pass/fail result shows the compliance results with the set requirements.
4
WHATS NEW IN VERSION 8.0?
5
Collect Parallel Active and Passive Surveys
This offers a quick and alternative method of sharing projects across applications without uploading via
the iBwave Cloud, in case wireless connections are slow or where company policy prevents cloud
uploads.
6
WHATS NEW IN VERSION 8.0?
OTHER ENHANCEMENTS
11) New automatic floor plan for new project
A standard floor plan is automatically created with a new design project.
7
NEW FEATURES BY PRODUCT
Improved Capacity
8
SERVICE RELEASES
SERVICE RELEASES
VERSION 8.0.1
The following issues have been resolved in iBwave Design Version 8.0.1.
DSGN-7882 Floor plan appears smaller than original size when opening IBWM file with A3 page
layout.
DSGN-8471 Imported wall image is rendered small and not centered on plan.
DSGN-8669 Allow import and export to ,IBWM option for all products except Viewer licenses.
DSGN-8670 An image on a duplicated plan reverts back to the original after changes are made
and when switching between plans.
DSGN-8678 The Duplicate button is disabled in the DB Editor when a public component is
selected.
DSGN-8690 Setting the prediction area can cause the application to stop working.
DSGN-8694 Changes in SNIR MIMO maps due to TDD calculations impact existing designs.
9
SERVICE RELEASES
VERSION 8.0.2
The following issues have been resolved in iBwave Design Version 8.0.2.
DSGN-8777 Missing file format types when exporting to IBWC collection data.
10
SERVICE RELEASES
VERSION 8.0.3
The following issues have been resolved in iBwave Design Version 8.0.3.
DSGN-8704 Power should not flow out of the OIM card when a Design project file created in a
previous Design version 7.0, is opened in Design version 8.0.
DSGN-8812 The debug message A single system cannot be used by multiple sources that
applies to regular DAS setup for example BTS that has same
operator/technology/band/sector should not be displayed for Clustered Small Cell
setup.
DSGN-8854 The Maximum Achievable Data Rate MIMO output map does not output the
expected values with respect to MIMO Gain properties.
DSGN-8866 An attempt to import iBwave projects to Mentum Planet a second time after a first
failed attempt is prevented by an error that detects items already found in dictionary.
11
SERVICE RELEASES
VERSION 8.0.4
The following issues have been resolved in iBwave Design Version 8.0.4.
DSGN-4296 Negative heights for inclined planes cause problems in calibration and prediction vs
measured data report.
12
SERVICE RELEASES
VERSION 8.0.5
The following issues have been resolved in iBwave Design Version 8.0.5.
DSGN-8855 Missing interpolation on survey points whose survey data was previously imported
from iBwave Mobile.
DSGN-8919 Access to iBwave Drive folders is inconsistent with set folder privileges.
DSGN-8983 The Max Average Power warning message appears on a splitter whose composite
power does not exceed the value set in Part properties.
DSGN-9055 Cable connected to antenna on MIMO Path 2 is not displayed on Horizontal Link
Budget report nor on Custom XML export.
13
SERVICE RELEASES
VERSION 8.0.6
The following issues have been resolved in iBwave Design Version 8.0.6.
DSGN-9063 Deleting all output maps in a project causes the application to stop working.
DSGN-9083 Adding a zone on the default layer of a layout plan in single mode causes the
application to stop working.
DSGN-9159 Missing option to add remote modules on same optical interface module for a power
sharing service group.
DSGN-9160 The application stops working when in a manual survey a combination of scrolling
and zooming is done while collecting data points.
DSGN-9207 The reference signal power is not updated when LTE bandwidth is changed for
multiple sectors.
DSGN-9221 An empty Horizontal Link Budget report is generated due to mismatched strands in
optical connectors.
DSGN-9222 Missing legend color scheme localization for Map Subtraction map.
DSGN-9223 Due to changes to capacity settings in version 8.0 a project saved in 7.0 format does
not work when opened in iBwave Design version 7.0.
14
SERVICE RELEASES
VERSION 8.1
The following issues have been resolved in iBwave Design Version 8.1.
DSGN-4998 Filenames of imported image files must be displayed without their paths.
DSGN-9275 Walls are not imported properly with AutoCAD file import.
15
SERVICE RELEASES
VERSION 8.1.1
The following issues have been resolved in iBwave Design Version 8.1.1.
DSGN-9232 Ability to install iBwave Design from command line without installing Error Report,
Zendesk or Team Viewer.
DSGN-9337 VPLE results of different environments are shifted to wrong floors when ground floor
is not at ground level.
DSGN-9398 Vex files created in version 6.6 cannot be opened in the current version.
16
SERVICE RELEASES
VERSION 8.1.2
The following issues have been resolved in iBwave Design Version 8.1.2.
DSGN-9385 Cannot import a .DWG file due to index out of range error.
DSGN-9446 Printing a project to PDF displays the color pixels slightly off the plan.
DSGN-9491 Walls are incorrectly selected when moving around the walls.
DSGN-9555 Aligning a line flush with the top of a plan causes the application to stop working.
17
NEXT STEPS
NEXT STEPS
Register to Attend a Live iBwave Product Suite Demo
Email: support@ibwave.com
Phone:
Log into the iBwave Customer Portal, and create a request in the My Cases section:
http://my.ibwave.com
Check if your questions are answered in the Knowledge Base section of the iBwave Customer
Portal
18
Other Enhancements