Professional Documents
Culture Documents
Summary of Structural Calculation of 2-Barrel Box Culvert
Summary of Structural Calculation of 2-Barrel Box Culvert
2 Design Parameters
1 / 60 362149023.xls/Summary
Coefficient of static earth pressure Ka= 0.33
2 / 60 362149023.xls/Summary
STRUCTURAL CALCULATION OF BOX CULVERT Type: B1.75m x H2.00m x 2 Class III Road
Soil Cover Depth: 0.6 m
1 Dimensions and Parameters
Basic Parameters Basic Conditions
Ka: Coefficient of static earth pressure 0.3333 Classification of Live load by truck Class 3
gw: Unit weight of water (t/m3) 1.00 t/m3 PTM: Truck load of Middle Tire 5.00 t
gd: Unit weight of soil (dry) (t/m3) 1.80 t/m3 Ii: Impact coefficient (D4.0m:0, D<4.0m:0.3) 0.3
gs: Unit weight of soil (saturated) (t/m3) 2.00 t/m3 am: Ground contact length of Middle Tire 0.10 m
gc: Unit weight of reinforced concrete (t/m3) 2.40 t/m3 bm: Ground contact width of Middle Tire 0.25 m
sck: Concrete Design Strength 175 kgf/cm2 PTR: Truck load of Rear Tire 5.00 t
sca Allowable Stress of Concrete 60 kgf/cm2 ar: Ground contact length of Rear Tire 0.10 m
ssa: Allowable Stress of Reinforcement Bar 1400 kgf/cm2 br: Ground contact width of Rear Tire 0.25 m
tma: Allowable Stress of Shearing (Concrete) 5.5 kgf/cm2 PTF: Truck load of Front wheel 1.25 t
ssy: Yielding Point of Reinforcement Bar 3000 kgf/cm2 af: Ground contact length of Front Tire 0.10 m
n: Young's Modulus Ratio 24 bf: Ground contact width of Front Tire 0.25 m
Fa: Safety factor against uplift 1.2 qp: Pedestrian load 0.00 t/m2
Basic Dimensions
H: Internal Height of Box Culvert 2.00 m
B: Internal Width of Each Box Culvert 1.75 m
Hf: Fillet Height 0.15 m
t1: Thickness of Side Wall 0.25 m (> 0.25m)
t2: Thickness of Top Slab 0.25 m (> 0.25m)
t3: Thickness of Invert (Bottom Slab) 0.25 m (> 0.25m)
t4: Thickness of Partition wall 0.25 m (> 0.25m)
BT: Gross Width of Box Culvert 4.25 m
HT: Gross Height of Box Culvert 2.50 m
D: Covering Depth 0.60 m (> 0.5m)
Gwd: Underground Water Depth for Case 1, 2 0.00 m (= D)
hiw: Internal Water Depth for Case 1, 2 0.00 m
for Case 3, 4 1.75 m
Gwd
D
Hf
t3
t1 B t4 B t1
B
T
Dimensions of frame
BT
t1 B t4 B t1 D1
t2
H H0
t3
B0 B0
BT0
3/ 60 (1)362149023.xls, Load
H0: Height of frame t2/2 + H + t3/2 2.250 m
BT0: Width of whole frame 2B + t1 + t4 4.000 m
D1: Cavering depth at middle of top slab D + t2/2 0.725 m
B0: Width of each conduit B+t1/2+t4/2 2.000 m
4/ 60 (1)362149023.xls, Load
Load distribution load by truck tire
(1) Middle tire's acting point: center of the top slab
a) distributed load of middle tire
Pvtm: distributed load of middle tire 2PTM(1+Ii)(2BT0-bm')/(am'BT0^2) 1.7012 tf/m2, B= 4.000 m
am': length of distirbuted load 2D+1.75+bm = 3.200 m
bm': width of distributed load 2D+am = 1.300 m
b) distributed load of rear tire
Pvtr: distributed load of rear tire not reach to top slab 0.0000 tf/m2, B= 0.000 m
ar': length of distirbuted load 2D+1.75+br = 3.200 m
br': width of distributed load 2D+ar = 1.300 m
c) distributed load of front tire
Pvtf: distributed load of front tire not reach to top slab 0.0000 tf/m2, B= 0.000 m
af': length of distirbuted load 2D+1.75+bf = 3.200 m
bf': width of distributed load 2D+af = 1.300 m
Case.L1: Pvt1 = 1.7012 tf/m2, B= 4.000 m Combination for Case.L2 (2) (2) (3) (3)
Pvt2 = 0.0000 tf/m2, B= 0.000 m a) + b) a) + c) a) + b) a) + c)
Case.L2: Pvt1 = 3.9063 tf/m2, B= 4.000 m Distributed load total 3.1250 3.9063 3.1250 3.1250
Pvt2 = 0.0000 tf/m2, B= 0.000 m Select the combination case of 3.9063 tf/m2,
for Case.L2, which is the largest load to the top slab.
In case of covering depth (D) is over 3.0m, uniform load of 1.0 tf/m2 is applied on the top slab of culvert insetead of live load calculated above.
5/ 60 (1)362149023.xls, Load
3 Load calculation
Case 1: Box Culvert Inside is Empty, Underground Water up to Top slab, Track load Case. L1
5) ground reaction
Acting Load (tf/m2)
Wbot=(t3*BT+2*Hf^2)*gc/BT0 Wbot= 0.6645
Wtop Wtop= 0.6645
Ws=(Wsw*2+Wpw)/BT0 Ws= 0.9000
Pvd Pvd= 1.2000
Pvt1 Pvt1= 1.7012
Pvt2 Pvt2= 0.0000
Wiw=2*(hiw*B-2Hf^2)*gw/BT0 Wiw= 0.0000 hiw: internal water depth 0.00 m
Up=-U/BT0 U= -2.6563
Q= 2.4739
6/ 60 (1)362149023.xls, Load
Case 2: Box Culvert Inside is Empty, Underground Water up to Top slab, Track load Case. L2
5) ground reaction
Acting Load (tf/m2)
Wbot=(t3*BT+2*Hf^2)*gc/BT0 Wbot= 0.6645
Wtop Wtop= 0.6645
Ws=(Wsw*2+Wpw)/BT0 Ws= 0.9000
Pvd Pvd= 1.2000
Pvt1 Pvt1= 3.9063
Pvt2 Pvt2= 0.0000
Wiw=2*(hiw*B-2Hf^2)*gw/BT0 Wiw= 0.0000 hiw: internal water depth 0.00 m
Up=-U/B0 U= -2.6563
Q= 4.6790
7/ 60 (1)362149023.xls, Load
Case 3: Box Culvert Inside is Full, Underground Water up to invert, Track load Case. L1
5) ground reaction
Acting Load (tf/m2)
Wbot=(t3*BT+2*Hf^2)*gc/BT0 Wbot= 0.6645
Wtop Wtop= 0.6645
Ws=(Wsw*2+Wpw)/BT0 Ws= 0.9000
Pvd Pvd= 1.0800
Pvt1 Pvt1= 1.7012
Pvt2 Pvt2= 0.0000
Wiw=2*(hiw*B-2Hf^2)*gw/BT0 Wiw= 1.5200 hiw: internal water depth 1.75 m
Up=0 U= 0.0000
Q= 6.5302
8/ 60 (1)362149023.xls, Load
Case 4: Box Culvert Inside is Full, Underground Water up to invert, Track load Case. L2
5) ground reaction
Acting Load (tf/m2)
Wbot=(t3*BT+2*Hf^2)*gc/BT0 Wbot= 0.6645
Wtop Wtop= 0.6645
Ws=(Wsw*2+Wpw)/BT0 Ws= 0.9000
Pvd Pvd= 1.0800
Pvt1 Pvt1= 3.9063
Pvt2 Pvt2= 0.0000
Wiw=(hiw*B-2Hf^2)*gw/BT0 Wiw= 1.5200 hiw: internal water depth 1.75 m
Up=0 U= 0.0000
Q= 8.7353
9/ 60 (1)362149023.xls, Load
Item Pv1 Ph1 Ph2 Pq Wsw Wpw q1
Case (tf/m2) (tf/m2) (tf/m2) (tf/m2) (tf/m) (tf/m) (tf/m2)
Case.1 3.5657 1.2083 4.9581 4.4657 1.2000 1.2000 2.4739
Case.2 5.7708 2.5102 6.2601 6.6708 1.2000 1.2000 4.6790
Case.3 3.4457 0.4350 -0.2152 4.3457 1.2000 1.2000 6.5302
Case.4 5.6508 1.7369 1.0868 6.5508 1.2000 1.2000 8.7353
Case 1: Box Culvert Inside is Empty, Underground Water up to Top slab, Track load Case. L1
Pv1=3.57 tf/m2
B t2=0.25m C t2=0.25m E Ph1=1.21 tf/m2 Ph3=1.21 tf/m2
B C E
H0=2.25m t1=0.25m t4=0.25m t1=0.25m
A A D F
F
t3=0.25m D t3=0.25m Ph2=4.96 tf/m2 Ph4=4.96 tf/m2
Q1=4.47 tf/m2
B0 =2.00m B0 =2.00m
k1 = 1.0
k2 = H0t23/(B0t13) = 1.12500
k3 = H0t3 /(B0t )
3
1
3
= 1.12500
k4 = H0t4 /(H0t )
3
1
3
= 1.00000
qA = -qF qB = -qE qC = qD = 0 R =0
qA = -0.05144 R = -0.064347
qB = -0.02817
The maximum bending moment occurs at the point of that shearing force equal to zero.
Sx = 0 = SAB - w1x - (w2 - w1)x2/(2L)
= 4.4185 -4.9581 x + 0.8333 x^2 , x = 4.8587
1.0913
Bending moment at x = 1.0913 m is;
Mmax = SABx - w1x /2 - (w2-w1)x /(6L) + MAB
2 3
= 0.6405 tfm
c) Bending Moment
MB = MBC = -1.0348 tfm
MC = -MCB = -1.3740 tfm
Sx = SBC - w1x = 3.39603 - 3.566 x = 0 , x = 0.9524
Bending moment at x = 0.9524 m is;
Mmax = SBCx - w1x2/2 + MBC = 0.58247 tfm
c) Bending Moment
MD = MDA = -1.3293 tfm
MA = -MAD = -1.5900 tfm
Sx = SDA - w1x = 4.33531 - 4.466 x = 0 , x = 0.9708
Bending moment at x = 0.9708 m is;
Mmax = SDAx - w1x2/2 + MDA = 0.7751 tfm
c) Bending Moment
MC = MCD = 0.0000 tfm
MD = -MDC = 0.0000 tfm
Sx = SCD - w1x = 0.000 - 0.000 x = 0 , x = -
Bending moment at x = 1.1250 m is;
Mmax = SCDx - w1x2/2 + MCD = 0.000 tfm
Pv1=5.77 tf/m2
B t2=0.25m C t2=0.25m E Ph1=2.51 tf/m2 Ph3 =2.51 tf/m2
B C E
H0=2.25m t1=0.25m t4=0.25m t1=0.25m
A A D F
F
t3=0.25m D t3=0.25m Ph2 =6.26 tf/m2 Ph4 =6.26 tf/m2
Q1=6.67 tf/m2
B0 =2.00m B0 =2.00m
k1 = 1.0
k2 = H0t23/(B0t13) = 1.12500
k3 = H0t33/(B0t13) = 1.12500
k4 = H0t4 /(H0t )
3
1
3
= 1.00000
qA = -qF qB = -qE qC = qD = 0 R =0
qA = -0.1086 R = -0.0643
qB = 0.0290
c) Bending Moment
MB = MBC = -1.6412 tfm
MC = -MCB = -2.1734 tfm
Sx = SBC - w1x = 5.50465 - 5.771 x = 0 , x = 0.9539
Bending moment at x = 0.9539 m is;
Mmax = SBCx - w1x2/2 + MBC = 0.9842 tfm
c) Bending Moment
MD = MDA = -2.1286 tfm
MA = -MAD = -2.1964 tfm
Sx = SDA - w1x = 6.6368 - 6.671 x = 0 , x = 0.9949
Bending moment at x = 0.9949 m is;
Mmax = SDAx - w1x2/2 + MDA = 1.1730 tfm
c) Bending Moment
MC = MCD = 0.00000 tfm
MD = -MDC = 0.00000 tfm
Sx = SCD - w1x = 0 - 0.000 x = 0 , x = -
Bending moment at x = 1.1250 m is;
Mmax = SCDx - w1x2/2 + MCD = 0.000 tfm
Pv1=3.45 tf/m2
B t2=0.25m C t2=0.25m E Ph1=0.43 tf/m2 Ph3 =0.43 tf/m2
B C E
H0=2.25m t1=0.25m t4=0.25m t1=0.25m
A A D F
F
t3=0.25m D t3=0.25m Ph2 =-0.22 tf/m2 Ph4 =-0.22 tf/m2
Q1=4.35 tf/m2
B0 =2.00m B0 =2.00m
k1 = 1.0
k2 = H0t23/(B0t13) = 1.12500
k3 = H0t33/(B0t13) = 1.12500
k4 = H0t4 /(H0t )
3
1
3
= 1.00000
qA = -qF qB = -qE qC = qD = 0 R =0
qA = -0.47720 R = -0.09040
qB = 0.29338
The maximum bending moment occurs at the point of that shearing force equal to zero.
Sx = 0 = SAB - w1x - (w2 - w1)x2/(2L)
= 0.2224 0.2152 x + -0.14447 x^2 , x = -0.702
2.192
Bending moment at x = 2.1918 m is;
Mmax = SABx - w1x /2 - (w2-w1)x /(6L) + MAB
2 3
= -0.1826 tfm
c) Bending Moment
MB = MBC = -0.1834 tfm
MC = -MCB = -1.7837 tfm
Sx = SBC - w1x = 2.6455 - 3.446 x = 0 , x = 0.7678
Bending moment at x = 0.7678 m is;
Mmax = SBCx - w1x2/2 + MBC = 0.8322 tfm
c) Bending Moment
MD = MDA = -1.6803 tfm
MA = -MAD = -0.6800 tfm
Sx = SDA - w1x = 4.84585 - 4.346 x = 0 , x = 1.1151
Bending moment at x = 1.1151 m is;
Mmax = SDAx - w1x2/2 + MDA = 1.0215 tfm
c) Bending Moment
MC = MCD = 0.00000 tfm
MD = -MDC = 0.00000 tfm
Sx = SCD - w1x = 0 - 0.000 x = 0 , x = -
Bending moment at x = 1.1250 m is;
Mmax = SCDx - w1x2/2 + MCD = 0 tfm
Pv1=5.65 tf/m2
B t2=0.25m C t2=0.25m E Ph1=1.74 tf/m2 Ph3 =1.74 tf/m2
B C E
H0=2.25m t1=0.25m t4=0.25m t1=0.25m
A A D F
F
t3=0.25m D t3=0.25m Ph2 =1.09 tf/m2 Ph4 =1.09 tf/m2
Q1=6.55 tf/m2
B0 =2.00m B0 =2.00m
k1 = 1.0
k2 = H0t23/(B0t13) = 1.12500
k3 = H0t33/(B0t13) = 1.12500
k4 = H0t4 /(H0t )
3
1
3
= 1.00000
qA = -qF qB = -qE qC = qD = 0 R =0
qA = -0.53436 R = -0.09040
qB = 0.35054
c) Bending Moment
MA = MAB = -1.28637 tfm
c) Bending Moment
MB = MBC = -0.7898 tfm
MC = -MCB = -2.5830 tfm
Sx = SBC - w1x = 4.7541 - 5.651 x = 0 , x = 0.8413
Bending moment at x = 0.8413 m is;
Mmax = SBCx - w1x2/2 + MBC = 1.2101 tfm
c) Bending Moment
MD = MDA = -2.4796 tfm
MA = -MAD = -1.2864 tfm
Sx = SDA - w1x = 7.14738 - 6.551 x = 0 , x = 1.0911
Bending moment at x = 1.0911 m is;
Mmax = SDAx - w1x2/2 + MDA = 1.41954 tfm
c) Bending Moment
MC = MCD = 0.00000 tfm
MD = -MDC = 0.00000 tfm
Sx = SCD - w1x = 0 - 0.000 x = 0 , x = -
Bending moment at x = 1.1250 m is;
Mmax = SCDx - w1x2/2 + MCD = 0 tfm
Check M N S (tf)
Member Case
Point (tfm) (tf) at joint at 2d
Side wall A -1.590 4.596 4.418 2.569
(left) Case.1 Middle 0.640 4.014 0.000 -
B -1.035 3.396 -2.519 -1.902
A -2.196 6.705 5.883 3.512
Case.2 Middle 0.857 6.117 0.000 -
B -1.641 5.505 -3.983 -2.846
A -0.680 3.845 0.222 0.285
Case.3 Middle -0.183 2.677 0.000 -
B -0.183 2.645 -0.025 0.126
A -1.286 5.954 1.687 1.229
Case.4 Middle -0.117 5.250 0.000 -
B -0.790 4.754 -1.490 -0.818
Top slab B -1.035 2.519 3.396 1.970
(left) Case.1 Middle 0.582 2.519 0.000 -
C -1.374 2.519 -3.735 -2.309
B -1.641 3.983 5.505 3.196
Case.2 Middle 0.984 3.983 0.000 -
C -2.173 3.983 -6.037 -3.729
B -0.183 0.025 2.645 1.267
Case.3 Middle 0.832 0.025 0.000 -
C -1.784 0.025 -4.246 -2.868
B -0.790 0.025 4.754 2.494
Case.4 Middle 1.210 0.025 0.000 -
C -2.583 0.025 -6.547 -4.287
Partition C 0.000 7.471 0.000 0.000
wall Case.1 Middle 0.000 8.071 0.000 -
D 0.000 8.671 0.000 0.000
C 0.000 12.074 0.000 0.000
Case.2 Middle 0.000 12.674 0.000 -
D 0.000 13.274 0.000 0.000
C 0.000 8.492 0.000 0.000
Case.3 Middle 0.000 9.092 0.000 -
D 0.000 9.692 0.000 0.000
C 0.000 13.095 0.000 0.000
Case.4 Middle 0.000 13.695 0.000 -
D 0.000 14.295 0.000 0.000
Invert D -1.329 4.418 4.335 2.549
(left) Case.1 Middle 0.775 4.418 0.000 -
A -1.590 4.418 -4.596 -2.810
D -2.129 5.883 6.637 3.969
Case.2 Middle 1.173 5.883 0.000 -
A -2.196 5.883 -6.705 -4.036
D -1.680 0.222 4.846 3.108
Case.3 Middle 1.021 0.222 0.000 -
A -0.680 0.222 -3.845 -2.107
D -2.480 1.687 7.147 4.527
Case.4 Middle 1.420 1.687 0.000 -
A -1.286 1.687 -5.954 -3.334
Case.2
M= 2.1964 tfm sca = 60 kgf/m2 h= 25 cm (height of member)
N= 6.7047 tf ssa = 1400 kgf/m2 d= 20 cm (effective height of member)
S0= 5.8832 tf n= 24 d' = 5 cm (protective covering depth)
S2d= 3.5125 tf c= 7.50 cm (distance from neutral axis)
b= 100 cm
e = M/N = 32.7593 cm
Solving the fomula shown below, sc = 38.9162 kgf/cm2 ( 4.5E-05 kgf/cm2) o.k.
sc^3+{3ssa/(2n) - 3N(e+c)/(bd^2)}sc^2 - 6N(e+c)ssasc/(nbd^2) - 3N(e+c)ssa^2/(n^2bd^2) = 0
0 = sc^3 +67.26 sc^2 -2361.8 sc -68887.05
s = nsc/(nsc+ssa) = 0.4002
Asreq = (sc*s/2 - N/(bd))bd/ssa = 6.3346 cm2
Case.3
M= 0.6800 tfm sca = 60 kgf/m2 h= 25 cm (height of member)
N= 3.8455 tf ssa = 1400 kgf/m2 d= 20 cm (effective height of member)
S0= 0.2224 tf n= 24 d' = 5 cm (protective covering depth)
S2d= 0.2854 tf c= 7.50 cm (distance from neutral axis)
b= 100 cm
e = M/N = 17.6818 cm
Solving the fomula shown below, sc = 20.4316 kgf/cm2 ( 2.3E-07 kgf/cm2) o.k.
sc^3+{3ssa/(2n) - 3N(e+c)/(bd^2)}sc^2 - 6N(e+c)ssasc/(nbd^2) - 3N(e+c)ssa^2/(n^2bd^2) = 0
0 = sc^3 +80.24 sc^2 -847.32 sc -24713.45
s = nsc/(nsc+ssa) = 0.2594
Asreq = (sc*s/2 - N/(bd))bd/ssa = 1.0389 cm2
Case.4
M= 1.2864 tfm sca = 60 kgf/m2 h= 25 cm (height of member)
N= 5.9541 tf ssa = 1400 kgf/m2 d= 20 cm (effective height of member)
S0= 1.6871 tf n= 24 d' = 5 cm (protective covering depth)
S2d= 1.2293 tf c= 7.50 cm (distance from neutral axis)
b= 100 cm
e = M/N = 21.6047 cm
Solving the fomula shown below, sc = 29.2154 kgf/cm2 ( 2.6E-06 kgf/cm2) o.k.
sc^3+{3ssa/(2n) - 3N(e+c)/(bd^2)}sc^2 - 6N(e+c)ssasc/(nbd^2) - 3N(e+c)ssa^2/(n^2bd^2) = 0
0 = sc^3 +74.5 sc^2 -1516.3 sc -44225.83
s = nsc/(nsc+ssa) = 0.3337
Asreq = (sc*s/2 - N/(bd))bd/ssa = 2.7109 cm2
The maximum requirement of reinforcement bar is 6.3346 cm2 in Case2 from above calculation.
Case. 1 2 3 4
Requirement 4.5376 6.3346 1.0389 2.7109 (cm2)
Case.2
M= 1.6412 tfm sca = 60 kgf/m2 h= 25 cm (height of member)
N= 5.5047 tf ssa = 1400 kgf/m2 d= 20 cm (effective height of member)
Case.4
M= 0.7898 tfm sca = 60 kgf/m2 h= 25 cm (height of member)
N= 4.7541 tf ssa = 1400 kgf/m2 d= 20 cm (effective height of member)
S0= 1.4895 tf n= 24 d' = 5 cm (protective covering depth)
S2d= 0.8179 tf c= 7.50 cm (distance from neutral axis)
b= 100 cm
e = M/N = 16.6123 cm
Solving the fomula shown below, sc = 22.6200 kgf/cm2 ( 1.1E-08 kgf/cm2) o.k.
sc^3+{3ssa/(2n) - 3N(e+c)/(bd^2)}sc^2 - 6N(e+c)ssasc/(nbd^2) - 3N(e+c)ssa^2/(n^2bd^2) = 0
0 = sc^3 +78.9 sc^2 -1003 sc -29255.26
s = nsc/(nsc+ssa) = 0.2794
Asreq = (sc*s/2 - N/(bd))bd/ssa = 1.1188 cm2
The maximum requirement of reinforcement bar is 4.3989 cm2 in Case2 from above calculation.
Case. 1 2 3 4
Requirement 2.6800 4.3989 0.0000 1.1188 (cm2)
Case.2
M= 1.6412 tfm sca = 60 kgf/m2 h= 25 cm (height of member)
N= 3.9834 tf ssa = 1400 kgf/m2 d= 20 cm (effective height of member)
S0= 5.5047 tf n= 24 d' = 5 cm (protective covering depth)
S2d= 3.1964 tf c= 7.50 cm (distance from neutral axis)
b= 100 cm
e = M/N = 41.2000 cm
Solving the fomula shown below, sc = 31.3869 kgf/cm2 ( 2.9E-07 kgf/cm2) o.k.
sc^3+{3ssa/(2n) - 3N(e+c)/(bd^2)}sc^2 - 6N(e+c)ssasc/(nbd^2) - 3N(e+c)ssa^2/(n^2bd^2) = 0
0 = sc^3 +72.95 sc^2 -1697.4 sc -49508.81
s = nsc/(nsc+ssa) = 0.3498
Asreq = (sc*s/2 - N/(bd))bd/ssa = 4.9976 cm2
Case.3
M= 0.1834 tfm sca = 60 kgf/m2 h= 25 cm (height of member)
N= 0.0248 tf ssa = 1400 kgf/m2 d= 20 cm (effective height of member)
S0= 2.6455 tf n= 24 d' = 5 cm (protective covering depth)
S2d= 1.2672 tf c= 7.50 cm (distance from neutral axis)
b= 100 cm
e = M/N = 738.91 cm
Solving the fomula shown below, sc = 8.0001 kgf/cm2 ( 0.00095 kgf/cm2) o.k.
sc^3+{3ssa/(2n) - 3N(e+c)/(bd^2)}sc^2 - 6N(e+c)ssasc/(nbd^2) - 3N(e+c)ssa^2/(n^2bd^2) = 0
0 = sc^3 +86.11 sc^2 -162.06 sc -4726.74
s = nsc/(nsc+ssa) = 0.1206
Asreq = (sc*s/2 - N/(bd))bd/ssa = 0.6715 cm2
Case.4
M= 0.7898 tfm sca = 60 kgf/m2 h= 25 cm (height of member)
N= 0.0248 tf ssa = 1400 kgf/m2 d= 20 cm (effective height of member)
S0= 4.7541 tf n= 24 d' = 5 cm (protective covering depth)
S2d= 2.4938 tf c= 7.50 cm (distance from neutral axis)
b= 100 cm
e = M/N = 3182.82 cm
The maximum requirement of reinforcement bar is 4.9976 cm2 in Case2 from above calculation.
Case. 1 2 3 4
Requirement 3.0344 4.9976 0.6715 3.0522 (cm2)
Case.2
M= 2.1964 tfm sca = 60 kgf/m2 h= 25 cm (height of member)
N= 5.8832 tf ssa = 1400 kgf/m2 d= 20 cm (effective height of member)
S0= 6.7047 tf n= 24 d' = 5 cm (protective covering depth)
S2d= 4.0364 tf c= 7.50 cm (distance from neutral axis)
b= 100 cm
e = M/N = 37.3336 cm
Solving the fomula shown below, sc = 38.3259 kgf/cm2 ( 7.3E-05 kgf/cm2) o.k.
sc^3+{3ssa/(2n) - 3N(e+c)/(bd^2)}sc^2 - 6N(e+c)ssasc/(nbd^2) - 3N(e+c)ssa^2/(n^2bd^2) = 0
0 = sc^3 +67.72 sc^2 -2307.9 sc -67314.67
s = nsc/(nsc+ssa) = 0.3965
Asreq = (sc*s/2 - N/(bd))bd/ssa = 6.6523 cm2
Case.3
M= 0.6800 tfm sca = 60 kgf/m2 h= 25 cm (height of member)
N= 0.2224 tf ssa = 1400 kgf/m2 d= 20 cm (effective height of member)
S0= 3.8455 tf n= 24 d' = 5 cm (protective covering depth)
S2d= 2.1072 tf c= 7.50 cm (distance from neutral axis)
b= 100 cm
e = M/N = ### cm
Solving the fomula shown below, sc = 16.8183 kgf/cm2 ( 2.4E-05 kgf/cm2) o.k.
sc^3+{3ssa/(2n) - 3N(e+c)/(bd^2)}sc^2 - 6N(e+c)ssasc/(nbd^2) - 3N(e+c)ssa^2/(n^2bd^2) = 0
0 = sc^3 +82.28 sc^2 -609.56 sc -17778.70
s = nsc/(nsc+ssa) = 0.2238
Asreq = (sc*s/2 - N/(bd))bd/ssa = 2.5295 cm2
Case.4
M= 1.2864 tfm sca = 60 kgf/m2 h= 25 cm (height of member)
N= 1.6871 tf ssa = 1400 kgf/m2 d= 20 cm (effective height of member)
S0= 5.9541 tf n= 24 d' = 5 cm (protective covering depth)
S2d= 3.3338 tf c= 7.50 cm (distance from neutral axis)
b= 100 cm
e = M/N = 76.2460 cm
Solving the fomula shown below, sc = 25.7138 kgf/cm2 ( 7.2E-05 kgf/cm2) o.k.
sc^3+{3ssa/(2n) - 3N(e+c)/(bd^2)}sc^2 - 6N(e+c)ssasc/(nbd^2) - 3N(e+c)ssa^2/(n^2bd^2) = 0
0 = sc^3 +76.9 sc^2 -1236.3 sc -36058.56
s = nsc/(nsc+ssa) = 0.3059
Asreq = (sc*s/2 - N/(bd))bd/ssa = 4.4142 cm2
The maximum requirement of reinforcement bar is 6.6523 cm2 in Case2 from above calculation.
Case. 1 2 3 4
Requirement 4.6077 6.6523 2.5295 4.4142 (cm2)
Case.2
M= 0.8574 tfm sca = 60 kgf/m2 h= 25 cm (height of member)
N= 6.1173 tf ssa = 1400 kgf/m2 d= 20 cm (effective height of member)
n= 24 d' = 5 cm (protective covering depth)
c= 7.50 cm (distance from neutral axis)
Case.4
M= 0.1169 tfm sca = 60 kgf/m2 h= 25 cm (height of member)
N= 5.2498 tf ssa = 1400 kgf/m2 d= 20 cm (effective height of member)
n= 24 d' = 5 cm (protective covering depth)
c= 7.50 cm (distance from neutral axis)
b= 100 cm
e = M/N = 2.2270 cm
Solving the fomula shown below, sc = 14.0580 kgf/cm2 ( 0.00068 kgf/cm2) o.k.
sc^3+{3ssa/(2n) - 3N(e+c)/(bd^2)}sc^2 - 6N(e+c)ssasc/(nbd^2) - 3N(e+c)ssa^2/(n^2bd^2) = 0
0 = sc^3 +83.67 sc^2 -446.82 sc -13032.22
s = nsc/(nsc+ssa) = 0.1942
Asreq = (sc*s/2 - N/(bd))bd/ssa = 0.0000 cm2 Tensile is on outside of member
The maximum requirement of reinforcement bar is 0.8473 cm2 in Case2 from above calculation.
Case. 1 2 3 4
Requirement 0.8094 0.8473 - - (cm2)
Side inside inside outside outside
Case.2
M= 0.9842 tfm sca = 60 kgf/m2 h= 25 cm (height of member)
N= 3.9834 tf ssa = 1400 kgf/m2 d= 20 cm (effective height of member)
n= 24 d' = 5 cm (protective covering depth)
c= 7.50 cm (distance from neutral axis)
b= 100 cm
e = M/N = 24.7081 cm
Solving the fomula shown below, sc = 24.2291 kgf/cm2 ( 0.00027 kgf/cm2) o.k.
sc^3+{3ssa/(2n) - 3N(e+c)/(bd^2)}sc^2 - 6N(e+c)ssasc/(nbd^2) - 3N(e+c)ssa^2/(n^2bd^2) = 0
0 = sc^3 +77.88 sc^2 -1122.6 sc -32743.07
s = nsc/(nsc+ssa) = 0.2935
Asreq = (sc*s/2 - N/(bd))bd/ssa = 2.2335 cm2 Tensile is on inside of member
Case.3
M= 0.8322 tfm sca = 60 kgf/m2 h= 25 cm (height of member)
N= 0.0248 tf ssa = 1400 kgf/m2 d= 20 cm (effective height of member)
n= 24 d' = 5 cm (protective covering depth)
c= 7.50 cm (distance from neutral axis)
b= 100 cm
e = M/N = ### cm
Solving the fomula shown below, sc = 18.6958 kgf/cm2 ( 2.2E-06 kgf/cm2) o.k.
sc^3+{3ssa/(2n) - 3N(e+c)/(bd^2)}sc^2 - 6N(e+c)ssasc/(nbd^2) - 3N(e+c)ssa^2/(n^2bd^2) = 0
0 = sc^3 +81.24 sc^2 -729.82 sc -21286.39
s = nsc/(nsc+ssa) = 0.2427
Asreq = (sc*s/2 - N/(bd))bd/ssa = 3.2235 cm2 Tensile is on inside of member
Case.4
M= 1.2101 tfm sca = 60 kgf/m2 h= 25 cm (height of member)
N= 0.0248 tf ssa = 1400 kgf/m2 d= 20 cm (effective height of member)
n= 24 d' = 5 cm (protective covering depth)
c= 7.50 cm (distance from neutral axis)
b= 100 cm
e = M/N = ### cm
The maximum requirement of reinforcement bar is 4.7674 cm2 in Case4 from above calculation.
Case. 1 2 3 4
Requirement 1.1894 2.2335 3.2235 4.7674 (cm2)
Side inside inside inside inside
Case.2
M= 1.1730 tfm sca = 60 kgf/m2 h= 25 cm (height of member)
N= 5.8832 tf ssa = 1400 kgf/m2 d= 20 cm (effective height of member)
n= 24 d' = 5 cm (protective covering depth)
c= 7.50 cm (distance from neutral axis)
b= 100 cm
e = M/N = 19.9377 cm
Solving the fomula shown below, sc = 27.9391 kgf/cm2 ( 9.1E-06 kgf/cm2) o.k.
sc^3+{3ssa/(2n) - 3N(e+c)/(bd^2)}sc^2 - 6N(e+c)ssasc/(nbd^2) - 3N(e+c)ssa^2/(n^2bd^2) = 0
0 = sc^3 +75.39 sc^2 -1412.4 sc -41195.84
s = nsc/(nsc+ssa) = 0.3238
Asreq = (sc*s/2 - N/(bd))bd/ssa = 2.2606 cm2 Tensile is on inside of member
Case.3
M= 1.0215 tfm sca = 60 kgf/m2 h= 25 cm (height of member)
N= 0.2224 tf ssa = 1400 kgf/m2 d= 20 cm (effective height of member)
n= 24 d' = 5 cm (protective covering depth)
c= 7.50 cm (distance from neutral axis)
b= 100 cm
e = M/N = ### cm
Solving the fomula shown below, sc = 21.3043 kgf/cm2 ( 7E-08 kgf/cm2) o.k.
sc^3+{3ssa/(2n) - 3N(e+c)/(bd^2)}sc^2 - 6N(e+c)ssasc/(nbd^2) - 3N(e+c)ssa^2/(n^2bd^2) = 0
0 = sc^3 +79.71 sc^2 -908.4 sc -26495.01
s = nsc/(nsc+ssa) = 0.2675
Asreq = (sc*s/2 - N/(bd))bd/ssa = 3.9120 cm2 Tensile is on inside of member
Case.4
M= 1.4195 tfm sca = 60 kgf/m2 h= 25 cm (height of member)
N= 1.6871 tf ssa = 1400 kgf/m2 d= 20 cm (effective height of member)
n= 24 d' = 5 cm (protective covering depth)
c= 7.50 cm (distance from neutral axis)
b= 100 cm
e = M/N = 84.1391 cm
Solving the fomula shown below, sc = 27.1953 kgf/cm2 ( 1.8E-05 kgf/cm2) o.k.
sc^3+{3ssa/(2n) - 3N(e+c)/(bd^2)}sc^2 - 6N(e+c)ssasc/(nbd^2) - 3N(e+c)ssa^2/(n^2bd^2) = 0
0 = sc^3 +75.9 sc^2 -1352.8 sc -39457.10
s = nsc/(nsc+ssa) = 0.3180
Asreq = (sc*s/2 - N/(bd))bd/ssa = 4.9715 cm2 Tensile is on inside of member
The maximum requirement of reinforcement bar is 4.9715 cm2 in Case4 from above calculation.
Case. 1 2 3 4
Requirement 1.1948 2.2606 3.9120 4.9715 (cm2)
Side inside inside inside inside
Case.2
M= 2.1734 tfm sca = 60 kgf/m2 h= 25 cm (height of member)
N= 3.9834 tf ssa = 1400 kgf/m2 d= 20 cm (effective height of member)
S0= 6.0368 tf n= 24 d' = 5 cm (protective covering depth)
Case.4
M= 2.5830 tfm sca = 60 kgf/m2 h= 25 cm (height of member)
N= 0.0248 tf ssa = 1400 kgf/m2 d= 20 cm (effective height of member)
S0= 6.5474 tf n= 24 d' = 5 cm (protective covering depth)
S2d= 4.2871 tf c= 7.50 cm (distance from neutral axis)
b= 100 cm
e = M/N = 10410 cm
Solving the fomula shown below, sc = 37.8189 kgf/cm2 ( 0.00011 kgf/cm2) o.k.
sc^3+{3ssa/(2n) - 3N(e+c)/(bd^2)}sc^2 - 6N(e+c)ssasc/(nbd^2) - 3N(e+c)ssa^2/(n^2bd^2) = 0
0 = sc^3 +68.11 sc^2 -2261.8 sc -65968.79
s = nsc/(nsc+ssa) = 0.3933
Asreq = (sc*s/2 - N/(bd))bd/ssa = 10.6073 cm2
The maximum requirement of reinforcement bar is 10.6073 cm2 in Case4 from above calculation.
Case. 1 2 3 4
Requirement 4.4479 7.2887 7.1687 10.6073 (cm2)
Case.2
M= 2.1286 tfm sca = 60 kgf/m2 h= 25 cm (height of member)
N= 5.8832 tf ssa = 1400 kgf/m2 d= 20 cm (effective height of member)
S0= 6.6368 tf n= 24 d' = 5 cm (protective covering depth)
S2d= 3.9685 tf c= 7.50 cm (distance from neutral axis)
b= 100 cm
e = M/N = 36.1810 cm
Solving the fomula shown below, sc = 37.6719 kgf/cm2 ( 0.00012 kgf/cm2) o.k.
sc^3+{3ssa/(2n) - 3N(e+c)/(bd^2)}sc^2 - 6N(e+c)ssasc/(nbd^2) - 3N(e+c)ssa^2/(n^2bd^2) = 0
0 = sc^3 +68.23 sc^2 -2248.6 sc -65584.17
s = nsc/(nsc+ssa) = 0.3924
Asreq = (sc*s/2 - N/(bd))bd/ssa = 6.3565 cm2
Case.3
M= 1.6803 tfm sca = 60 kgf/m2 h= 25 cm (height of member)
N= 0.2224 tf ssa = 1400 kgf/m2 d= 20 cm (effective height of member)
S0= 4.8459 tf n= 24 d' = 5 cm (protective covering depth)
S2d= 3.1076 tf c= 7.50 cm (distance from neutral axis)
b= 100 cm
e = M/N = ### cm
Solving the fomula shown below, sc = 28.8316 kgf/cm2 ( 3.8E-06 kgf/cm2) o.k.
sc^3+{3ssa/(2n) - 3N(e+c)/(bd^2)}sc^2 - 6N(e+c)ssasc/(nbd^2) - 3N(e+c)ssa^2/(n^2bd^2) = 0
0 = sc^3 +74.77 sc^2 -1484.9 sc -43308.70
s = nsc/(nsc+ssa) = 0.3308
Asreq = (sc*s/2 - N/(bd))bd/ssa = 6.6530 cm2
Case.4
M= 2.4796 tfm sca = 60 kgf/m2 h= 25 cm (height of member)
N= 1.6871 tf ssa = 1400 kgf/m2 d= 20 cm (effective height of member)
S0= 7.1474 tf n= 24 d' = 5 cm (protective covering depth)
S2d= 4.5271 tf c= 7.50 cm (distance from neutral axis)
b= 100 cm
The maximum requirement of reinforcement bar is 9.5128 cm2 in Case4 from above calculation.
Case. 1 2 3 4
Requirement 3.5020 6.3565 6.6530 9.5128 (cm2)
Case.2
M= 0.0000 tfm sca = 60 kgf/m2 h= 25 cm (height of member)
N= 12.6737 tf ssa = 1400 kgf/m2 d= 20 cm (effective height of member)
S0= 0.0000 tf n= 24 d' = 5 cm (protective covering depth)
c= 7.50 cm (distance from neutral axis)
b= 100 cm
e = M/N = 0.0000 cm
Solving the fomula shown below, sc = 20.2061 kgf/cm2 ( 3.1E-07 kgf/cm2) o.k.
sc^3+{3ssa/(2n) - 3N(e+c)/(bd^2)}sc^2 - 6N(e+c)ssasc/(nbd^2) - 3N(e+c)ssa^2/(n^2bd^2) = 0
0 = sc^3 +80.37 sc^2 -831.71 sc -24258.24
s = nsc/(nsc+ssa) = 0.2573
Asreq = (sc*s/2 - N/(bd))bd/ssa = 0.0000 cm2
Case.3
M= 0.0000 tfm sca = 60 kgf/m2 h= 25 cm (height of member)
N= 9.0917 tf ssa = 1400 kgf/m2 d= 20 cm (effective height of member)
S0= 0.0000 tf n= 24 d' = 5 cm (protective covering depth)
c= 7.50 cm (distance from neutral axis)
b= 100 cm
e = M/N = 0.0000 cm
Solving the fomula shown below, sc = 16.6097 kgf/cm2 ( 3.1E-05 kgf/cm2) o.k.
sc^3+{3ssa/(2n) - 3N(e+c)/(bd^2)}sc^2 - 6N(e+c)ssasc/(nbd^2) - 3N(e+c)ssa^2/(n^2bd^2) = 0
0 = sc^3 +82.39 sc^2 -596.64 sc -17402.09
s = nsc/(nsc+ssa) = 0.2216
Asreq = (sc*s/2 - N/(bd))bd/ssa = 0.0000 cm2
Case.4
M= 0.0000 tfm sca = 60 kgf/m2 h= 25 cm (height of member)
N= 13.6948 tf ssa = 1400 kgf/m2 d= 20 cm (effective height of member)
S0= 0.0000 tf n= 24 d' = 5 cm (protective covering depth)
c= 7.50 cm (distance from neutral axis)
b= 100 cm
e = M/N = 0.0000 cm
Solving the fomula shown below, sc = 21.1666 kgf/cm2 ( 8.5E-08 kgf/cm2) o.k.
sc^3+{3ssa/(2n) - 3N(e+c)/(bd^2)}sc^2 - 6N(e+c)ssasc/(nbd^2) - 3N(e+c)ssa^2/(n^2bd^2) = 0
0 = sc^3 +79.8 sc^2 -898.72 sc -26212.64
s = nsc/(nsc+ssa) = 0.2662
Asreq = (sc*s/2 - N/(bd))bd/ssa = 0.0000 cm2
The maximum requirement of reinforcement bar is 0.0000 cm2 in Case1 from above calculation.
Case. 1 2 3 4
Requirement 0.0000 0.0000 0.0000 0.0000 (cm2)
Required reinforcement for design is the maximum required reinforcment calculated above in 1) - 4).
Item Side wallSide wall Top slab Invert Side wall Top slab Invert Top slab Invert Par. Wall
Point botom top end end middle middle middle joint C joind D middle
Side outside outside outside outside inside inside inside outside outside both
Calculation 1) 2) 3) 4) 5) 6) 7) 8) 9) 10)
Requirment 6.3346 4.3989 4.9976 6.6523 0.8473 4.7674 4.9715 10.6073 9.5128 0.0000 (cm2)
Required R-bar Asreq cm2 6.335 0.847 4.399 4.998 4.767 10.607
Distribution bar (>As/6 and >Asmin) 12@250 12@250 12@250 12@250 12@250 12@250
Reinforcement As cm2 4.52 4.52 4.52 4.52 4.52 4.52
h1
h1
h2
Ha
h3
b1
b1 b2 b3
b3 b4
b4 b1
Bb
Bb
Section of Culvert
1. Design Data
b1 = 0.250 m b2 = 1.750 m b3 = 0.250 m b4 = 1.750 m
h1 = 0.250 m h2 = 2.000 m h3 = 0.250 m fillet = 0.150 m
Bb = 4.250 m Ha = 2.500 m d = 0.05 m
2. Data Pembesian
Bottom slab : Tumpuan Lapangan Tulangan bagi :
As1 (cm2) : O 12 @ 250 O 12 @ 250 O 12 @ 250
As2 (cm2) : O 12 @ 250 O 12 @ 250
As1 (cm2) : O 12 @ 125 (Tumpuan Tengah) O 12 @ 250 (Tumpuan Tepi)
Side wall : Tumpuan Lapangan Tulangan bagi :
As1 (cm2) : O 12 @ 250 O 12 @ 125 O 12 @ 250
As2 (cm2) : O 12 @ 125 O 12 @ 250
As1 (cm2) : O 12 @ 250 (Top wall)
Top slab : Tumpuan Lapangan Tulangan bagi :
As1 (cm2) : O 12 @ 250 O 12 @ 250 O 12 @ 250
As2 (cm2) : O 12 @ 250 O 12 @ 250
As1 (cm2) : O 12 @ 125 (Tumpuan Tengah)
3. Tulangan Miring (fillet) : Partition wall :
Bottom slab : O### @ ### O 12 @ 250
Top slab : O### @ ###
Ha
b1 b2 b3 b4
Bb
Section of Culvert
1. Design Data
b1 = 0.250 m b2 = 1.750 m b3 = 0.250 m b4 = 1.750
h1 = 0.250 m h2 = 2.000 m h3 = 0.250 m
Bb = 4.000 m Ha = 2.250 m
2. Result Calculation
Side wall (left) Ma Mmax Mb Sa Sb Na Nb
Case 1 -1.590 0.640 -1.035 4.418 -2.519 4.596 3.396
Case 3 -0.680 -0.183 -0.183 0.222 -0.025 3.845 2.645
Case 1
Mmax x x1 x2 x3 x4 x5 x6 x7
Mab = 1.091 -0.54 0.16 0.54 0.64 0.49 0.14 -0.38
Mef = 1.159 -0.54 0.16 0.54 0.64 0.49 0.14 -0.38
Mmax y1 y2 y3 y4 y5 y6 y7
Mbc = 0.952 -0.30 0.22 0.51 0.58 0.42 0.05 -0.55
Mad = 1.029 -0.58 0.15 0.60 0.77 0.67 0.28 -0.38
x x1 x2 x3 x4 x5 x6 x7
Sab 2.250 3.09 1.89 0.83 -0.10 -0.91 -1.58 -2.11
Case 2
Mmax x x1 x2 x3 x4 x5 x6 x7
Mab = 2.192 -0.61 -0.53 -0.44 -0.36 -0.29 -0.23 -0.19
Mef = 0.058 -0.61 -0.53 -0.44 -0.36 -0.29 -0.23 -0.19
Mmax y1 y2 y3 y4 y5 y6 y7
Mbc = 0.768 0.37 0.71 0.83 0.74 0.43 -0.09 -0.83
Mad = 0.885 0.15 0.70 0.98 0.99 0.73 0.20 -0.60
x x1 x2 x3 x4 x5 x6 x7
Sab 2.250 0.27 0.30 0.30 0.28 0.24 0.17 0.09
h1
h2
h3
b1
1.750 m
Nb MAB MBA
3.396 -1.590 -1.035
2.645 -0.680 -0.183
Nf MEF MFE
4.596 -1.035 -1.590
3.845 -0.183 -0.680
Nc MBC MCB
2.519 -1.035 -1.374
0.025 -0.183 -1.784
Nd MAD MDA
4.418 -1.590 -1.329
0.222 -0.680 -1.680
Nd MCD MDC
8.671 0.000 0.000
9.692 0.000 0.000
Ne MCE MEC
2.519 -1.374 -1.035
0.025 -1.784 -0.183
Nf MDF MFD
4.418 -1.329 -1.590
0.222 -1.680 -0.680
x7 q1 q2
-0.38 4.958 1.208
-0.38 1.208 4.958
y7 q1
-0.55 3.566
-0.38 4.466
1.969
1.750
x7
-2.11
x7 q1 q2
-0.19 -0.215 0.435
-0.19 0.435 -0.215
y7 q1
-0.83 3.446
-0.60 4.346
1.969
1.750
x7
0.09