Professional Documents
Culture Documents
1363 Bolts and Nut Standard PDF
1363 Bolts and Nut Standard PDF
March 2004
2. TEST RECORDS - All records of tests, inspection and calibration shall be kept in suitable
forms approved by the Bureau.
2.1 All testing apparatus/measuring instruments shall be periodically checked and calibrated and
records of such checks/calibration shall be maintained.
2.2 Copies of any records and other connected papers that may be required by the Bureau shall be
made available at any time on request.
3.1 In addition, effort should be made to gradually introduce a Quality Management System in
accordance with IS/ISO 9000 series as appropriate to the activities of the organization.
4.1 MARKING - In addition the following information should be given on the package/gunny
bags;
5.0 All bolts, screws and nuts conforming to specification shall be applied with the identification
mark as given in IS 1367(Pt.18):1996.
6.0 LEVELS OFF CONTROL - The tests, as indicated in Table 1, 2 & 3 attached and at
the levels of control specified therein, shall be carried out on the whole production of the factory
which is covered by this scheme and appropriate records and charts maintained in accordance
with paragraph 2.0 above. All the production which conforms to the Indian Standards and
covered by the licence shall be marked with certification mark of the Bureau.
6.1 CONTROL UNIT : All the bolts, screws and nuts of same property class and
designation manufactured during a day shall constitute a control unit.
DOC:STI/1363/4
March 2004
6.2.1 HEAT TREATMENT BATCH : All the bolts, screws and nuts of same property class
and designation heat treated together at the same time shall constitute a heat treatment batch.
7.0 In respect of all other clauses of the specification the factory will maintain appropriate
control and checks to ensure that their product conforms to the various requirements of this
specification.
9.0 SAMPLES The licensee shall supply, free of charge, the samples required in
accordance with the Bureau of Indian Standards (Certification) Regulations, 1988, as
subsequently amended, from the factory or godowns. The Bureau shall pay for the samples
taken by it from the open market.
10.0 REPLACEMENT Whenever a complaint is received soon after the goods with
Standard Marks have been purchased and used, and if there is adequate evidence that the goods
have not been misused, defective goods or their components are replaced or repaired free of cost
by the licensee in case the complaint is proved to be genuine and the warranty period (where
applicable) has not expired. The final authority to judge the conformity of the product to the
Indian Standard shall be with the Bureau.
10.1 In the event of any damages caused by the goods bearing the Standard Mark, or claim
being filed by the consumers against BIS Standard Mark and not conforming to the relevant
Indian Standard, entire liability arising out of such non conforming product shall be of licensee
and BIS shall not in any way be responsible in such cases.
11.0 STOP MARKING The marking of the product shall be stopped under intimation to the
Bureau if, at any time, there is some difficulty in maintaining the conformity of their product to
the specification, or the testing equipment goes out of order. The marking may be resumed as
soon as the defects are removed under intimation to Bureau.
11.1 The marking of the product shall be stopped immediately if directed to do so by Bureau
for any reason. The marking may then be resumed only after permission by the Bureau. The
information regarding resumption of markings shall also be sent to the Bureau.
12.0 PRODUCTION DATA The licensee shall send to BIS as per the enclosed
proforma-1 to be authenticated by a Chartered Accountant or by the manufacturer by giving an
affidavit/undertaking, a statement of quantity produced, marked and exported by him and the
trade value thereof at the end of each operative year of the licence.
Table 1
DOC:STI/1363/4
March 2004
IS 1363 (Pt.1):2002
HEXAGON HEAD BOLTS (SIZE RANGE M5 TO M64)
TABLE 1 LEVELS OF CONTROL
(Para 6 of the Scheme of Testing and Inspection)
IS 1363(Pt.2):2002
HEXAGON HEAD SCREWS (SIZE RANGE M5 TO M64)
TABLE 2 LEVELS OF CONTROL
(Para 6 of the Scheme of Testing and Inspection)
TEST DETAILS LEVELS OF CONTROL
Te Cl. Requirement Test Methods No. Lot Fre- Remarks
st of Size quency
Gr Clause Reference samples
ou
p
4. Material 4 IS 1367(Pt.3) One Each This test is required only
& Table 2 consig for those fasteners which
nment are not subjected to
tensile test. If the
material is supported by
suitable test certificate
regarding conformity of
material. No further
testing is required in the
factory.
3. Dimensions & Table 1 or IS 1363(Pt.2) As per The existing frequency of
tolerances Table 2 :2002 sampli dimensional verification
(as applicable) ng plan would be applicable only
given if firm is having adequate
in IS system of checking the
1367 dimensions and
(Pt.17) inspection at a frequency
of 15 minutes/30 minutes
for each operation.
4. a) Threads IS 4218 (Pt.3) -do- In case of failure, the
(Ta requirement IS 14962(Pt.1) production should be
ble stopped and setting of the
3) machine should be
rectified so as to produce
subsequent product
within the tolerance.
b) Mechanical (Ref:Table IS 1367(Pt.3)
properties 3 & 5)
Test Gr.
Properties
DOC:STI/1363/4
March 2004
IS 1363(Pt.2):2002
HEXAGON HEAD SCREWS (SIZE RANGE M5 TO M64)
TABLE 2 LEVELS OF CONTROL
(Para 6 of the Scheme of Testing and Inspection)
Note 1 The above tests are as per test programme which is recommended for in-process control.
Note 2. For applicability of test to a property class, reference may be made to Table 5 of IS 1367 (Pt.3)
Note 3 Sampling plan for electroplating test :