Professional Documents
Culture Documents
Industrialmecanic Noa2013 Eng
Industrialmecanic Noa2013 Eng
Industrial
Mechanic
(Millwright)
2013
Occupational
Analyses Series
Industrial Mechanic
(Millwright)
2013
This document is available on demand in alternative formats (Large Print, Braille, Audio
Cassette, Audio CD, e-Text Diskette, e-Text CD, or DAISY), by contacting 1 800 O-Canada
(1 800 622-6232). If you have a hearing or speech impairment and use a teletypewriter (TTY),
call 1 800 926-9105.
PDF
Cat. No.:
HS42-1/8-2013E-PDF
ISBN:
978-1-100-22967-6
FOREWORD
Background
The first National Conference on Apprenticeship in Trades and Industries, held in Ottawa in
1952, recommended that the federal government be requested to cooperate with provincial and
territorial apprenticeship committees and officials in preparing analyses of a number of skilled
occupations. To this end, Employment and Social Development Canada (ESDC) sponsors a
program, under the guidance of the CCDA, to develop a series of NOAs.
-I-
ACKNOWLEDGEMENTS
The CCDA and ESDC wish to express sincere appreciation for the contribution of the many
tradespersons, industrial establishments, professional associations, labour organizations,
provincial and territorial government departments and agencies, and all others who contributed
to this publication.
Special acknowledgement is extended by ESDC and the CCDA to the following representatives
from the trade.
This analysis was prepared by the Labour Market Integration Directorate of ESDC. The
coordinating, facilitating and processing of this analysis were undertaken by employees of the
NOA development team of the Trades and Apprenticeship Division. The host jurisdiction of
Manitoba also participated in the development of this NOA.
- II -
TABLE OF CONTENTS
FOREWORD I
ACKNOWLEDGEMENTS II
STRUCTURE OF ANALYSIS V
ANALYSIS
SAFETY 3
OCCUPATIONAL OBSERVATIONS 6
- III -
Task 11 Services chain and belt drive systems. 43
APPENDICES
APPENDIX B GLOSSARY 93
APPENDIX C ACRONYMS 95
- IV -
STRUCTURE OF ANALYSIS
Trends changes identified that impact or will impact the trade including
work practices, technological advances, and new materials and
equipment
Related Components a list of products, items, materials and other elements relevant to
the block
Tools and Equipment categories of tools and equipment used to perform all tasks in the
block; these tools and equipment are listed in Appendix A
-V-
The appendices located at the end of the analysis are described as follows:
Appendix C a list of acronyms used in the analysis with their full name
Acronyms
Appendix F a chart which outlines graphically the blocks, tasks and sub-tasks
Task Profile Chart of this analysis
- VI -
DEVELOPMENT AND VALIDATION OF ANALYSIS
Development of Analysis
A draft analysis is developed by a committee of industry experts in the field led by a team of
facilitators from ESDC. This draft analysis breaks down all the tasks performed in the
occupation and describes the knowledge and abilities required for a tradesperson to
demonstrate competence in the trade.
Draft Review
The NOA development team then forwards a copy of the analysis and its translation to
provincial and territorial authorities for a review of its content and structure. Their
recommendations are assessed and incorporated into the analysis.
The analysis is sent to all provinces and territories for validation and weighting. Participating
jurisdictions consult with industry to validate and weight the document, examining the blocks,
tasks and sub-tasks of the analysis as follows:
TASKS Each jurisdiction assigns a percentage of exam questions to each task within a
block.
SUB-TASKS Each jurisdiction indicates, with a YES or NO, whether or not each sub-task is
performed by skilled workers within the occupation in its jurisdiction.
The results of this exercise are submitted to the NOA development team who then analyzes the
data and incorporates it into the document. The NOA provides the individual jurisdictional
validation results as well as the national averages of all responses. The national averages for
block and task weighting guide the Interprovincial Red Seal Examination plan for the trade.
This method for the validation of the NOA also identifies common core sub-tasks across
Canada for the occupation. If at least 70% of the responding jurisdictions perform a sub-task, it
shall be considered common core. Interprovincial Red Seal Examinations are based on the
common core sub-tasks identified through this validation process.
- VII -
Definitions for Validation and Weighting
Provincial/Territorial Abbreviations
- VIII -
ANALYSIS
SAFETY
Safe working procedures and conditions, accident prevention, and the preservation of health
are of primary importance to industry in Canada. These responsibilities are shared and require
the joint efforts of government, employers and employees. It is imperative that all parties
become aware of circumstances that may lead to injury or harm. Safe learning experiences and
work environments can be created by controlling the variables and behaviours that may
contribute to accidents or injury.
It is imperative to apply and be familiar with the Occupational Health and Safety (OH&S) Acts
and Workplace Hazardous Materials Information System (WHMIS) regulations. As well, it is
essential to determine workplace hazards and take measures to protect oneself, co-workers, the
public and the environment.
Safety education is an integral part of training in all jurisdictions. As safety is an imperative part
of all trades, it is assumed and therefore it is not included as a qualifier of any activities.
However, the technical safety tasks and sub-tasks specific to the trade are included in this
analysis.
-3-
SCOPE OF THE INDUSTRIAL MECHANIC
(MILLWRIGHT) TRADE
Industrial Mechanic (Millwright) is this trades official Red Seal occupational title approved
by the CCDA. This analysis covers tasks performed by industrial mechanics (millwrights)
whose occupational title has been identified by some provinces and territories of Canada under
the following names:
NL NS PE NB QC ON MB SK AB BC NT YT NU
Industrial
Mechanic
(Millwright)
Millwright
Other tasks that may be performed in this trade include welding, cutting, rigging and
machining as required. Industrial mechanics (millwrights) may prepare bases for equipment.
Prints, diagrams, schematic drawings and manuals assist industrial mechanics (millwrights) in
determining work procedures.
Industrial mechanics (millwrights) work with a wide variety of tools. They may use hand and
power tools in installation and repair work. Larger machine tools such as lathes, drill presses
and grinders may be used in fabrication of machine parts. Hoisting and lifting equipment such
as cranes, jacks and forklifts is commonly used to position large machines or machine parts.
Industrial mechanics (millwrights) are employed in all sectors of industry that involve
mechanical moving equipment including mining, petrochemical, power generation, service and
food processing among others. Millwrights are involved with the installation, maintenance and
repair of machinery, equipment and components.
-4-
The work environment for industrial mechanics (millwrights) is varied and may involve
working in extreme or adverse conditions. They often work shift work. They may work in
confined spaces, at heights, with heavy equipment and around moving machinery. The work
often requires considerable standing, kneeling and lifting of materials.
Key skills for people in this trade are mechanical aptitude, problem-solving, communication,
job planning and organizing and the ability to use trade-related calculations. They have the
ability to detect malfunctions through sensory tests which are often confirmed by technical
tests. Other important attributes include good coordination, manual dexterity and the ability to
visualize a layout in three dimensions.
Industrial mechanics (millwrights) often possess overlapping skills with other tradespeople
such as steamfitter/pipefitter, industrial instrument mechanic, power engineer, welder,
machinist or industrial electrician. They may be certified in these other trades as well. Industrial
mechanics (millwrights) may work in specialized areas of the trade such as fluid analysis,
vibration analysis and laser alignment. With experience, they may advance to other positions
such as mentor, supervisor, planner, superintendent or trainer.
-5-
OCCUPATIONAL OBSERVATIONS
There is a progression from analog to digital equipment that provides computer generated
readouts and can be programmed to give accurate readings in less time. This technology allows
for improved self-diagnosis and predictive maintenance and has reduced the length of
mechanical outages and manpower required to complete outages. For example, the technology
has reduced equipment down time for tasks such as alignment, troubleshooting, assembly and
repair. Industrial mechanics (millwrights) need to keep pace with changes in technology.
Advances in predictive maintenance have led to more advanced diagnostic equipment such as
alignment equipment and vibration monitoring equipment. Acoustic monitoring technology is
advancing rapidly. Borescopes are increasingly used to view and troubleshoot internal
components. There is advanced diagnostic equipment for fluid power inspection such as
handheld analyzers and clamp-on flowmeters.
Hydraulic tools are continuously evolving in ease of use and size. They are becoming safer and
more efficient to use. Hydraulic technology is being used for broader applications.
The evolution of technology and the complexity of systems such as hydraulics, robotics, green
power panels and mechatronics are expanding the scope of work for industrial mechanics
(millwrights).
There is a wider variety of materials available for use in the construction of machinery and
components, such as new composite alloys and advanced plastics. More types of sealant and
epoxy materials are available to the industrial mechanic (millwright).
Preventive and predictive maintenance planning is seen as more important and scheduled
shutdowns are more prevalent. Reliability Centered Maintenance (RCM) methodology is
becoming more common because of its cost effectiveness.
Some hand and power tools are ergonomically designed to prevent repetitive strain injuries.
Many power tools are now cordless with improved battery life and light weight in design,
making them more ergonomically friendly, resulting in fewer injuries. There is an increased use
of mobile equipment such as forklifts, scissor lifts, aerial lifts and lift trucks in the trade. This
equipment is incorporating more safety features. Certification of the equipment and employees
is becoming mandatory.
-6-
Personal protective equipment (PPE) is becoming more user-friendly and protective, resulting
in increased usage among tradespersons. Improved identification of hazardous materials
through increased use of Material Safety Data Sheets (MSDS) contributes to a safer work
environment.
Quality assurance, reliability, maintainability and safety are critical elements of the standards
for industrial mechanic (millwrights). Continuous changes in technology, environmental
regulations and worker safety concerns have led to improved safety practices.
-7-
ESSENTIAL SKILLS SUMMARY
Essential skills are needed for work, learning and life. They provide the foundation for learning
all other skills and enable people to evolve with their jobs and adapt to workplace change.
Through extensive research, the Government of Canada and other national and international
agencies have identified and validated nine essential skills. These skills are used in nearly every
occupation and throughout daily life in different ways.
A series of CCDA-endorsed tools have been developed to support apprentices in their training
and to be better prepared for a career in the trades. The tools can be used independently or with
the assistance of a tradesperson, trainer, employer, teacher or mentor to:
The essential skills profile for the industrial mechanic (millwright) trade indicates that the most
important essential skills are document use, numeracy and critical thinking.
The application of these skills may be described throughout this document within the
competency statements which support each subtask of the trade. The following are summaries
of the requirements in each of the essential skills, taken from the essential skills profile. A link to
the complete essential skills profile can be found at www.red-seal.ca.
Reading
Industrial mechanics (millwrights) read texts such as short descriptions and directions on labels
for products. They read bulletins, manuals and procedures when installing, operating,
troubleshooting and repairing equipment. They also read emails and memos from supervisors,
co-workers and suppliers about ongoing work.
Document Use
Industrial mechanics (millwrights) scan and locate data on labels, lists, tables and schedules.
They may interpret graphs when monitoring equipment operation. They interpret or review
schematic drawings of systems (pneumatic, mechanical, structural and hydraulic) to identify
malfunction. Industrial mechanics (millwrights) may also retrieve and study data from scale
drawings to identify location of machinery to be installed and verify location of machinery.
They also complete forms such as purchase orders, maintenance forms, logbooks and work
orders.
-8-
Writing
Industrial mechanics (millwrights) write brief text entries in logbooks and in forms. They may
write maintenance and repair procedures. Industrial mechanics (millwrights) write emails to
supervisors, co-workers about ongoing works, and suppliers about equipment specifications.
They may also write incident reports.
Numeracy
Oral Communication
Thinking Skills
Industrial mechanics (millwrights) may problem solve by fabricating or adapting parts from
other machines when parts needed are not available for maintenance and repairs. They may
choose among refurbish, repair and replacement options for worn and defective parts such as
hoses, motors, valves and bushings. They take into consideration factors such as maintenance
guidelines, performance and test results, safety, efficiency and durability of replacement parts.
Industrial mechanics (millwrights) evaluate conditions of parts and equipment, and the safety
of their work environment. They assess feasibility of designs for small modifications to
equipment and machinery, ensuring that designs meet technical specifications, performance
requirements and regulations.
Industrial mechanics (millwrights) perform many of their tasks independently. They work with
others when necessary to install and overhaul larger pieces of equipment and complete
industrial systems.
-9-
Computer Use
Continuous Learning
Industrial mechanics (millwrights) may read manuals and bulletins to stay abreast of
developments in their trade. They also learn informally by exchanging information with co-
workers and suppliers. They may also attend training sessions on new technologies, equipment,
machinery and safety procedures.
- 10 -
BLOCK A COMMON OCCUPATIONAL SKILLS
Required Knowledge
K1 types of PPE such as safety glasses, gloves, face shields, hearing protection,
respiratory equipment, safety footwear and hard hats
K2 types of safety equipment such as fall arrest devices, first aid kits and eye
wash stations
K3 limitations of use of PPE and safety equipment
K4 PPE and safety equipment operations
K5 company safety policies and standard operating procedures (SOP)
K6 disposal and recycling procedures
K7 emergency procedures and location of on-site first aid stations and
equipment
- 11 -
K8 jurisdictional health and safety acts and regulations
K9 training requirements such as fall protection and confined space entry
K 10 clear path for access and egress into and out of confined spaces
K 11 workers rights and responsibilities
K 12 fire safety and hot work permit procedures
K 13 housekeeping practices
K 14 WHMIS
K 15 locations of WHMIS manuals and MSDS
K 16 lock-out, tag-out and zero energy procedures (individual or group)
K 17 environmental protection procedures
K 18 spill kits
K 19 due diligence
K 20 stored energy potential (thermal, electric, kinetic, radiation)
K 21 job safety analysis
K 22 hazards associated with performing condition-based monitoring using tools
with attached cables and straps while performing the activity on operating
equipment
Sub-task
A-1.01 Uses personal protective equipment (PPE) and safety equipment.
NL NS PE NB QC ON MB SK AB BC NT YT NU
yes yes yes yes NV yes yes yes yes yes NV NV NV
Key Competencies
A-1.01.01 organize PPE and safety equipment according to company policies and
OH&S regulations
A-1.01.02 select PPE and safety equipment specific to job task
A-1.01.03 recognize worn, damaged or defective PPE and safety equipment, and
remove from service
A-1.01.04 ensure proper fit of PPE and safety equipment
A-1.01.05 clean and store PPE and safety equipment according to manufacturers
recommendations
- 12 -
Sub-task
A-1.02 Maintains safe work environment.
NL NS PE NB QC ON MB SK AB BC NT YT NU
yes yes yes yes NV yes yes yes yes yes NV NV NV
Key Competencies
A-1.02.01 recognize and address hazards such as poor housekeeping that could cause
personal injury, or equipment or environmental damage
A-1.02.02 handle and store hazardous materials according to WHMIS
A-1.02.03 install safety protection such as signage, barrier tape and barricades
A-1.02.04 identify and implement adequate ventilation in workspace
A-1.02.05 ensure clear path of access to and egress from confined spaces
A-1.02.06 test air quality of confined spaces on a continuous basis using hand held
devices
A-1.02.07 follow confined space procedures and regulations
A-1.02.08 ensure cables and straps do not get caught in rotating equipment when
performing condition-based monitoring
Sub-task
A-1.03 Protects the environment.
NL NS PE NB QC ON MB SK AB BC NT YT NU
yes yes yes yes NV yes yes yes yes yes NV NV NV
Key Competencies
A-1.03.01 recognize hazards that could cause personal injury and harm the
environment, and report potential hazards
A-1.03.02 follow due diligence procedures to avoid contamination of water, air and soil
based on jurisdictional regulations and company policies
A-1.03.03 follow disposal procedures of hazardous material
- 13 -
Sub-task
A-1.04 Performs lock-out/tag-out and zero energy procedures.
NL NS PE NB QC ON MB SK AB BC NT YT NU
yes yes yes yes NV yes yes yes yes yes NV NV NV
Key Competencies
A-1.04.01 recognize and de-energize stored energy potential in machines, process
systems and components such as accumulators, suspended loads, and
pneumatic and hydraulic cylinders
A-1.04.02 follow recognized SOP for shutdown, lock-out and tag-out
Required Knowledge
- 14 -
K 10 operation, application and limitations of tools and equipment
K 11 hazards associated with shop machines
K 12 regulations and procedures governing the use of rigging, hoisting/lifting and
moving equipment
K 13 safety policies and procedures
K 14 shop machine components
K 15 speeds and feeds
K 16 welding techniques such as gas metal arc welding (GMAW [MIG]), gas
tungsten arc welding (GTAW [TIG]), shielded metal arc welding (SMAW),
metal-cored arc welding (MCAW), flux-cored arc welding (FCAW), plasma
and plastic
K 17 manufacturers recommendations
K 18 jurisdictional and employer safety regulations
K 19 methods and recommended environmental conditions for storing tools and
equipment
K 20 cleaning and handling of tools and equipment
Sub-task
A-2.01 Maintains hand and portable power tools.
NL NS PE NB QC ON MB SK AB BC NT YT NU
yes yes yes yes NV yes yes yes yes yes NV NV NV
Key Competencies
A-2.01.01 clean and lubricate hand and portable power tools according to
manufacturers recommendations
A-2.01.02 recognize worn, damaged or defective hand and portable power tools, and
remove from service
A-2.01.03 store hand and portable power tools according to manufacturers
recommendations
- 15 -
Sub-task
A-2.02 Maintains precision measuring and layout tools.
NL NS PE NB QC ON MB SK AB BC NT YT NU
yes yes yes yes NV yes yes yes yes yes NV NV NV
Key Competencies
A-2.02.01 clean and lubricate precision measuring and layout tools according to
manufacturers recommendations
A-2.02.02 verify and set calibration of precision measuring tools before every use
A-2.02.03 recognize worn, damaged or defective precision measuring tools, and remove
from service for recalibration, repair or disposal
A-2.02.04 store precision measuring and layout tools according to manufacturers
recommendations
Sub-task
A-2.03 Maintains rigging, hoisting/lifting and moving equipment.
NL NS PE NB QC ON MB SK AB BC NT YT NU
yes yes yes yes NV yes yes yes yes yes NV NV NV
Key Competencies
A-2.03.01 perform scheduled maintenance on equipment such as lubricating and
cleaning
A-2.03.02 perform visual inspection of rigging, hoisting/lifting and moving equipment
A-2.03.03 identify and replace damaged hardware such as eye-bolts, slings, shackles
and hooks, and remove from service
A-2.03.04 identify non-destructive testing (NDT) techniques used on hoisting/lifting
equipment to detect underlying defects such as cracks
A-2.03.05 store rigging, hoisting/lifting and moving equipment according to
manufacturers recommendations and/or OH&S regulations
- 16 -
Sub-task
A-2.04 Maintains welding equipment.
NL NS PE NB QC ON MB SK AB BC NT YT NU
yes yes yes yes NV yes yes yes yes yes NV NV NV
Key Competencies
A-2.04.01 perform scheduled maintenance on oxy-acetylene units such as inspecting
and replacing hoses, gauges, valves and mixing chamber
A-2.04.02 perform scheduled maintenance on electrically powered units such as
inspecting and replacing plugs, cables, clamps, bottles, gauges and hoses
A-2.04.03 perform scheduled maintenance on mobile welding units such as inspecting
plugs, cables, clamps, bottles, gauges, hoses and vehicle/trailer
A-2.04.04 store equipment according to manufacturers recommendations, OH&S and
WHMIS regulations
Sub-task
A-2.05 Uses shop machines.
NL NS PE NB QC ON MB SK AB BC NT YT NU
yes yes yes yes NV yes yes yes yes yes NV NV NV
Key Competencies
A-2.05.01 set up shop machines according to task at hand
A-2.05.02 identify fit and assembly requirements
A-2.05.03 apply coolants and cutting fluids
A-2.05.04 clean and lubricate shop machines
A-2.05.05 cut, drill, machine and grind workpiece as required
- 17 -
Sub-task
A-2.06 Uses access equipment.
NL NS PE NB QC ON MB SK AB BC NT YT NU
yes yes yes yes NV yes yes yes yes yes NV NV NV
Key Competencies
A-2.06.01 select access equipment according to task at hand and taking into
consideration unstable conditions such as soft ground and ramps
A-2.06.02 set-up and use access equipment according to OH&S regulations and
company recommendations
A-2.06.03 identify unsafe, worn, damaged or defective access equipment, and remove
from service for repair or disposal
A-2.06.04 clean and lubricate access equipment according to manufacturers
recommendations
A-2.06.05 store access equipment according to manufacturers recommendations
Required Knowledge
K1 basic metallurgy
K2 properties and characteristics of common types of metals and materials used
in the trade
K3 compatibility of metals and of other materials
K4 torque values, tensile strength and metal capability
K5 established job requirements such as personnel and schedule of operations
K6 fabricating techniques
K7 heat treatment procedures such as annealing, hardening, tempering and
normalizing of metals
K8 personal and environment hazards of lubricants
K9 lubricant qualities such as viscosity and drop points
K 10 lubricating systems and components
K 11 metric and imperial systems
- 18 -
K 12 alignment and leveling practices
K 13 safe practices for handling hot metals
K 14 safe practices for isolating equipment and achieving a zero energy state
K 15 symbols and conventions used in drawings and schematics
K 16 types of fastening devices such as nuts, bolts, rivets, screws and adhesives,
and their characteristics and specifications
K 17 types of retaining devices such as keys, retaining rings, springs, dowels and
pins
Sub-task
A-3.01 Plans work.
NL NS PE NB QC ON MB SK AB BC NT YT NU
yes yes yes yes NV yes yes yes yes yes NV NV NV
Key Competencies
A-3.01.01 determine scope of job
A-3.01.02 develop safety plan according to job requirements
A-3.01.03 determine the types of tools and equipment needed
A-3.01.04 identify required materials
A-3.01.05 schedule work with other tradespersons and personnel
A-3.01.06 estimate time to complete job
Sub-task
A-3.02 Fabricates workpiece.
NL NS PE NB QC ON MB SK AB BC NT YT NU
yes yes yes yes NV yes yes yes yes yes NV NV NV
Key Competencies
A-3.02.01 select and use shop tools such as milling machines, surface grinders and
lathes
A-3.02.02 identify fabrication requirements such as size, strength and materials
required according to specifications
A-3.02.03 identify fit and assembly requirements according to specifications
A-3.02.04 select fabrication materials such as ferrous and non-ferrous metal
- 19 -
A-3.02.05 lay out workpiece
A-3.02.06 cut, drill, grind and weld workpiece as required
A-3.02.07 inspect fabricated workpiece is in accordance with specifications
Sub-task
A-3.03 Lubricates systems and components.
NL NS PE NB QC ON MB SK AB BC NT YT NU
yes yes yes yes NV yes yes yes yes yes NV NV NV
Key Competencies
A-3.03.01 select and use tools and equipment such as hand tools, PPE, grease guns and
oil cans
A-3.03.02 determine lubricants/fluid requirements according to site and manufacturers
specifications and technical manuals
A-3.03.03 identify points requiring lubricants according to manufacturers
specifications
A-3.03.04 maintain lubricant levels
A-3.03.05 remove and replace lubricants
A-3.03.06 clean systems and components
Sub-task
A-3.04 Performs leveling of components and systems.
NL NS PE NB QC ON MB SK AB BC NT YT NU
yes yes yes yes NV yes yes yes yes yes NV NV NV
Key Competencies
A-3.04.01 select and use levelling tools such as optical, laser and spirit levels
A-3.04.02 level and shim machinery and components according to site and
manufacturers specifications
A-3.04.03 record leveling data to demonstrate compliance
A-3.04.04 perform site evaluation
- 20 -
Sub-task
A-3.05 Uses fastening and retaining devices.
NL NS PE NB QC ON MB SK AB BC NT YT NU
yes yes yes yes NV yes yes yes yes yes NV NV NV
Key Competencies
A-3.05.01 select and use tools and equipment such as torque wrenches, impact
wrenches and hydraulic tensioning devices, to install or remove fastening
and retaining devices
A-3.05.02 select fastening and retaining devices according to application
A-3.05.03 select and apply chemical fasteners for anchoring purposes
A-3.05.04 achieve predetermined torque or tensioning by stretching fasteners using
heat or hydraulics
A-3.05.05 select and verify thread pitch (imperial or metric) on fastener using thread
pitch gauges
A-3.05.06 select fluids and compounds associated with threaded fasteners such as
lubrication and thread lockers
A-3.05.07 clean, chase, plug, drill and tap threads
A-3.05.08 restore threads using a thread restoration kit
Sub-task
A-3.06 Tests metal and other materials using standardized procedures.
NL NS PE NB QC ON MB SK AB BC NT YT NU
yes yes yes yes NV yes yes yes yes yes NV NV NV
Key Competencies
A-3.06.01 select and use tools and equipment such as hammers, chisels, grinders and
magnets
A-3.06.02 select ferrous and non-ferrous metals and materials according to
manufacturers specifications
A-3.06.03 identify common types of metals by filing, chiselling and examining the chips
(chisel test)
A-3.06.04 identify common types of metal by grinding and examining the colour, shape
and length of the sparks (spark test)
A-3.06.05 identify common types of metals using the magnet test
- 21 -
Sub-task
A-3.07 Performs heat treatment of metal.
NL NS PE NB QC ON MB SK AB BC NT YT NU
yes yes yes yes NV yes yes yes yes yes NV NV NV
Key Competencies
A-3.07.01 select and use tools and equipment such as ovens, forges and oxy-fuel torches
A-3.07.02 clean component for heat treatment to remove contaminants
A-3.07.03 heat metal to reach predetermined colour according to heat treatment colour
charts
Sub-task
A-3.08 Uses mechanical drawings and schematics.
NL NS PE NB QC ON MB SK AB BC NT YT NU
yes yes yes yes NV yes yes yes yes yes NV NV NV
Key Competencies
A-3.08.01 determine and recognize locations of equipment, components and parts from
mechanical drawings
A-3.08.02 interpret and cross-reference engineering assembly and installation
drawings, process and instrumentation (P & ID) drawings, schematics and
sketches, specifications and technical manuals to visualize the outcome
A-3.08.03 perform trade-related calculations
A-3.08.04 produce field drawings and freehand schematic drawings
A-3.08.05 identify symbols such as hydraulic, welding and pneumatic
A-3.08.06 update mechanical drawings to reflect the as-built (red line) drawings
- 22 -
Task 4 Performs measuring and layout.
Required Knowledge
Sub-task
A-4.01 Prepares work area, tools and materials.
NL NS PE NB QC ON MB SK AB BC NT YT NU
yes yes yes yes NV yes yes yes yes yes NV NV NV
Key Competencies
A-4.01.01 acclimatize optical precision, measuring, layout and leveling tools according
to environmental conditions
A-4.01.02 verify optical precision, measuring, layout and leveling tools for calibration
A-4.01.03 prepare material to be measured by cleaning or filing
A-4.01.04 clean and prepare work area such as table, floor and wall by removing
obstructions
- 23 -
Sub-task
A-4.02 Measures material and components.
NL NS PE NB QC ON MB SK AB BC NT YT NU
yes yes yes yes NV yes yes yes yes yes NV NV NV
Key Competencies
A-4.02.01 select and use measuring tools and equipment such as tape measures, vernier
calipers, micrometers and total station (jig and transit) according to accuracy
required
A-4.02.02 read and interpret measurements according to tolerances
A-4.02.03 transfer measurements to components, work area and material, according to
tolerances
A-4.02.04 take inside and outside dimensions such as diameters, bores, lengths and
thicknesses
A-4.02.05 level and align components such as sole plates and bases according to
drawings and specifications
Sub-task
A-4.03 Lays out components.
NL NS PE NB QC ON MB SK AB BC NT YT NU
yes yes yes yes NV yes yes yes yes yes NV NV NV
Key Competencies
A-4.03.01 select and use layout tools and equipment such as plumb bobs, optical levels
and transits, protractors, lasers, straightedges, combination set and total
station (jig and transit) according to task and accuracy required
A-4.03.02 transfer measurements from benchmark and datum points to work area
A-4.03.03 transfer measurements from drawings to work material
- 24 -
Task 5 Performs cutting and welding operations.
Required Knowledge
Sub-task
A-5.01 Cuts material with gas and plasma arc cutting equipment.
NL NS PE NB QC ON MB SK AB BC NT YT NU
yes yes yes yes NV yes yes yes yes yes NV NV NV
Key Competencies
A-5.01.01 identify and prepare material to be cut according to job requirements
A-5.01.02 select and use tools and equipment such as oxy-acetylene torches, plasma arc
and gougers
A-5.02.03 select gas for cutting
- 25 -
A-5.01.04 perform cutting procedures according to tools and equipment used and
materials to be cut
A-5.01.05 perform plasma arc cutting procedures according to materials to be cut
Sub-task
A-5.02 Joins material using gas welding equipment.
NL NS PE NB QC ON MB SK AB BC NT YT NU
yes yes yes yes NV yes yes yes no yes NV NV NV
Key Competencies
A-5.02.01 select and prepare material to be welded/brazed and soldered according to
job requirements and material compatibility
A-5.02.02 select and use tools such as tips according to job requirements
A-5.02.03 match filler rods and flux to materials to be welded, brazed or soldered
A-5.02.04 perform welding, brazing and soldering procedures according to materials
being welded/brazed and soldered
A-5.02.05 prepare the workpiece according to procedural requirements such as
cleaning, pre-heating and post-heating
Sub-task
A-5.03 Welds material using shielded arc welding equipment (SMAW).
NL NS PE NB QC ON MB SK AB BC NT YT NU
yes yes yes yes NV yes yes yes no yes NV NV NV
Key Competencies
A-5.03.01 select and prepare material to be welded according to job requirements and
material compatibility
A-5.03.02 select and use electrodes according to site and job requirements
A-5.03.03 perform welding procedures according to materials being welded
A-5.03.04 adjust amperage and polarity to achieve proper fusion and penetration
A-5.03.05 visually inspect welds to ensure proper fusion and penetration
A-5.03.06 prepare the workpiece according to procedural requirements such as
cleaning, pre-heating and post-heating
- 26 -
Sub-task
A-5.04 Welds material with gas metal arc welding (GMAW [MIG])
equipment.
NL NS PE NB QC ON MB SK AB BC NT YT NU
yes yes yes yes NV yes yes yes no yes NV NV NV
Key Competencies
A-5.04.01 select and prepare material to be welded according to job requirements and
material compatibility
A-5.04.02 select types of gas used for welding
A-5.04.03 select and use wire according to site and job requirements
A-5.04.04 perform welding procedures according to materials being welded
A-5.04.05 adjust amperage, shielding gas flow and feed rate to achieve proper fusion
and penetration
A-5.04.06 visually inspect welds to ensure proper fusion and penetration
A-5.04.07 prepare the workpiece according to procedural requirements such as
cleaning, pre-heating and post-heating
Sub-task
A-5.05 Welds material with gas tungsten arc welding (GTAW [TIG])
equipment.
NL NS PE NB QC ON MB SK AB BC NT YT NU
yes yes yes yes NV yes yes yes no yes NV NV NV
Key Competencies
A-5.05.01 select and prepare material to be welded according to job requirements and
material compatibility
A-5.05.02 select types of gas used for welding
A-5.05.03 select and use filler rods and tungsten according to site and job requirements
A-5.05.04 perform welding procedures according to materials being welded
A-5.05.05 adjust amperage, shielding gas flow, frequency, polarity and tungsten to
achieve proper fusion and penetration
A-5.05.06 visually inspect welds to ensure proper fusion and penetration
A-5.05.07 prepare the workpiece according to procedural requirements such as
cleaning, pre-heating and post-heating
- 27 -
BLOCK B RIGGING, HOISTING/LIFTING AND MOVING
Related Chain falls, tirfors, block and tackles, shackles, slings, come-alongs,
Components chains, rope (nylon, fibre, wire), spreader bars, lifting beams, eye-bolts,
(including, but not hoist rings, hooks, overhead crane, mobile crane, forklift truck,
limited to) hydraulic hoist, hydraulic jacks, gantries, jacks, snatch blocks, tuggers,
hand winches
Required Knowledge
K1 rigging equipment such as block and tackles, chains, wire ropes, nylon slings,
eye-bolts, hoist rings, hooks, softeners, turnbuckles, tag lines, dunnage,
spreaders bars, lifting beams and shackles
K2 hoisting/lifting and moving equipment such as overhead crane, mobile crane,
forklift truck, hydraulic hoist, gantries, jacks, tuggers, engineered
bases/rolling devices, hand winches, come-alongs, chain falls and snatch
blocks
K3 fibre ropes, knots and hitches
K4 applications and limitations of equipment
K5 requirements for engineered lifts
K6 safe rigging, hoisting/lifting and moving practices
K7 safety factors and working load limits (WLL)
K8 safety regulations when rigging, hoisting/lifting and moving
- 28 -
K9 weight, size/dimensions of working load and centre of gravity principles
K 10 ground and environmental conditions, and possible changes
K 11 load charts
K 12 characteristics (size, shape, wet/dry) of load being lifted
K 13 shipping information
K 14 nameplate (ID plate) and manuals
Sub-task
B-6.01 Determines load.
NL NS PE NB QC ON MB SK AB BC NT YT NU
yes yes yes yes NV yes yes yes yes yes NV NV NV
Key Competencies
B-6.01.01 scale the load using weighing devices such as hanging scales and
dynamometers
B-6.01.02 calculate load weight taking into consideration size, wet/dry, centre of
gravity, added components and weight of rigging
B-6.01.03 refer to nameplates, shipping information and manufacturers manuals
Sub-task
B-6.02 Selects rigging equipment.
NL NS PE NB QC ON MB SK AB BC NT YT NU
yes yes yes yes NV yes yes yes yes yes NV NV NV
Key Competencies
B-6.02.01 determine rigging equipment needed based on the characteristics of the lift,
process (for example, lifting, dragging and pulling sideways), the number of
items being lifted at one time and determined weight of load
B-6.02.02 refer to load ratings for sling arrangements such as basket vs. choker
B-6.02.03 confirm rigging capacity is appropriate for the lift taking into consideration
WLL, design factor and actual weight of load being lifted
B-6.02.04 confirm certification of rigging equipment by referring to the equipments tag
or documentation
- 29 -
B-6.02.05 assess, inspect and document rigging equipment condition to ensure they
meet companys safety policies, jurisdictional regulations and/or
manufacturers tolerances and specifications
B-6.02.06 remove and tag faulty or damaged rigging equipment from service to be
repaired or discarded, and report to supervisor
Sub-task
B-6.03 Selects hoisting/lifting and moving equipment.
NL NS PE NB QC ON MB SK AB BC NT YT NU
yes yes yes yes NV yes yes yes yes yes NV NV NV
Key Competencies:
B-6.03.01 determine hoisting/lifting and moving equipment needed based on the job
scope (for example, headroom, environment, ground conditions,
obstructions, weather and distance), process (for example, lifting, dragging
and pulling sideways) and determined weight of load
B-6.03.02 assess, inspect and document condition of hoisting/lifting and moving
equipment
B-6.03.03 confirm certification of hoisting/lifting and moving equipment by referring to
operators manuals, and the equipments document of certification
B-6.03.04 refer to load ratings for boom angles and distance
B-6.03.05 remove and tag faulty or damaged hoisting/lifting and moving equipment
from service to be repaired or discarded, and report to supervisor
- 30 -
Task 7 Rigs, hoists/lifts and moves load.
Context Rigging, hoisting/lifting and moving loads are hazardous activities and
care must be taken to ensure the safety of all personnel and prevent
damage to equipment. Industrial mechanics (millwrights) must be
skilled in the proper procedures for rigging, hoisting, lifting, drifting,
dragging and rolling loads.
Required Knowledge
Sub-task
B-7.01 Secures area.
NL NS PE NB QC ON MB SK AB BC NT YT NU
yes yes yes yes NV yes yes yes yes yes NV NV NV
Key Competencies
B-7.01.01 assess site, ground, environmental conditions and plan route
B-7.01.02 determine and secure lift radius using barricades and tape
B-7.01.03 confirm location of personnel
- 31 -
Sub-task
B-7.02 Sets up rigging, hoisting/lifting and moving equipment.
NL NS PE NB QC ON MB SK AB BC NT YT NU
yes yes yes yes NV yes yes yes yes yes NV NV NV
Key Competencies:
B-7.02.01 prepare for lift by using methods such as putting floats under outriggers, and
providing cribbing and dunnage
B-7.02.02 install and/or set-up all rigging, hoisting/lifting and moving components in
preparation for use
B-7.02.03 perform pre-use inspection of equipment to verify conditions such as fuel
levels, tire pressure and absence of leaks
B-7.02.04 read and interpret load charts
B-7.02.05 adjust schedule to address environmental conditions such as wind, shifting
ground, lightning, fog, rain and snow
Sub-task
B-7.03 Performs hoist/lift and move.
NL NS PE NB QC ON MB SK AB BC NT YT NU
yes yes yes yes NV yes yes yes yes yes NV NV NV
Key Competencies:
B-7.03.01 ensure direct line of sight between the operator and signal person
B-7.03.02 use hand signals according to OH&S regulations
B-7.03.03 use two-way radio communication when there is no direct line of sight
B-7.03.04 assess and make adjustments to stabilize load as required
B-7.03.05 adjust schedule to address environmental conditions such as wind, changing
ground conditions, lightning, fog, rain and snow
B-7.03.06 perform post-lift inspection of rigging, hoisting/lifting and moving
equipment
- 32 -
BLOCK C MECHANICAL COMPONENTS AND SYSTEMS
Related Prime movers: internal combustion engines (gas and diesel), turbines
Components (wind, steam, gas, hydraulic), electric motors (DC, AC).
(including, but not Power transmission assemblies: belt drives, gear drives, chain drives,
limited to) clutches, brakes, couplings.
Required Knowledge
- 33 -
K7 condition-based monitoring technologies such as vibration analysis,
ultrasonic technology (UT), fluid analysis, infrared thermography and motor
current analysis
K8 condition-based monitoring tools such as strobe lights, stethoscope, vibration
data collectors, infrared cameras and temperature guns
K9 diagnostic procedures using appropriate condition-based monitoring
technology(ies) and tools
K 10 equipment and their restrictions
K 11 hazards such as flammable liquids, steam and electrical shock
K 12 installation sequences and procedures
K 13 machinery specifications such as fluid levels, temperatures and pressures
K 14 manufacturers or job site specifications
K 15 operating principles
K 16 regulations and procedures governing the use of rigging, hoisting/lifting and
moving equipment
K 17 decommissioning procedures
Sub-task
C-8.01 Installs prime movers.
NL NS PE NB QC ON MB SK AB BC NT YT NU
yes yes yes yes NV yes yes yes yes yes NV NV NV
Key Competencies
C-8.01.01 select and use tools and equipment such as torque wrenches, dial indicators,
precision levels and optical or laser alignment equipment according to job
C-8.01.02 determine location and elevation for installation according to engineered
drawings
C-8.01.03 prepare foundation according to engineered drawings
C-8.01.04 clean and rough-up base for prime movers by methods such as filing,
sandblasting and buffing
C-8.01.05 position prime movers manually or with rigging, hoisting/lifting and moving
equipment
C-8.01.06 secure, level and align prime mover with driven equipment according to
manufacturers and site specifications, and engineered drawings
C-8.01.07 connect prime mover to driven equipment using components such as
couplings, sheaves, sprockets and gear boxes according to engineered
specifications and drawings
- 34 -
C-8.01.08 install auxiliary systems such as lube pumps, over-speed trip and governors
according to manufacturers specifications
C-8.01.09 bump test to check rotation prior to coupling up
C-8.01.10 install safety guards according to manufacturers specifications and OH&S
regulations
C-8.01.11 energize equipment and start-up/return to operation
Sub-task
C-8.02 Diagnoses prime movers.
NL NS PE NB QC ON MB SK AB BC NT YT NU
yes yes yes yes NV yes yes yes yes yes NV NV NV
Key Competencies
C-8.02.01 obtain a description of the problem and symptoms
C-8.02.02 perform sensory inspection of prime movers such as listening for excessive
noise, smelling burned components and feeling for excessive vibration
C-8.02.03 use test/evaluation procedures and specialized equipment according to
results of sensory inspection
C-8.02.04 perform condition-based monitoring routine procedures to detect underlying
defects not identified through sensory inspection
C-8.02.05 inspect prime mover components such as couplings, bearings and sheaves for
defects including excessive wear, corrosion and looseness
C-8.02.06 remove and replace safety guards according to manufacturers and site
specifications
C-8.02.07 assess and detect faulty or damaged equipment to determine next steps such
as repair or replace
C-8.02.08 tag and report faulty or damaged equipment
- 35 -
Sub-task
C-8.03 Repairs prime movers.
NL NS PE NB QC ON MB SK AB BC NT YT NU
yes yes yes yes NV yes yes yes yes yes NV NV NV
Key Competencies
C-8.03.01 rebuild and replace faulty components and auxiliary equipment according to
manufacturers specifications
C-8.03.02 use precision measuring tools such as laser alignment equipment,
micrometers, torque wrenches and vernier calipers
C-8.03.03 dismantle, remove and reassemble prime movers and components to
specifications using tools and procedures and match (witness) marks
C-8.03.04 align components according to manufacturers specifications
C-8.03.05 bump test to check rotation prior to coupling up
C-8.03.06 energize equipment and start-up/return to operations
Context Shafts transmit power and torque from the prime mover to the driven
equipment. Bearings maintain the shaft centerline and allow rotary or
linear shaft movement with minimal friction. Seals prevent
contamination of other components and ensure lubrication
containment. Servicing includes installing, diagnosing, repairing and
maintaining these components.
Required knowledge
- 36 -
K9 bearing fits and tolerances
K 10 bearing materials such as new alloys and advanced plastics
K 11 initial, installed and running bearing clearances according to manufacturers
specification charts
K 12 types of shafts such as drive, counter, jack and hollow
K 13 lubrication requirements
K 14 manufacturers specifications
K 15 seal faults such as leaking, deterioration and improper installation
K 16 seal materials compatibility with medium
K 17 types of seals such as static, dynamic, mechanical, contact and non-contact
K 18 shaft faults such as bent and worn shafts
K 19 shaft restoration applications such as shaft straightening, spray welding,
peening, knurling and using sleeves
K 20 condition-based monitoring technologies such as vibration analysis, UT, fluid
analysis, infrared thermography and motor current analysis
K 21 condition-based monitoring tools such as strobe lights, stethoscope, vibration
data collectors, infrared cameras and temperature guns
K 22 diagnostic procedures using appropriate condition-based monitoring
technology(ies) and tools
Sub-task
C-9.01 Installs shafts, bearings and seals.
NL NS PE NB QC ON MB SK AB BC NT YT NU
yes yes yes yes NV yes yes yes yes yes NV NV NV
Key Competencies
C-9.01.01 select and use tools and equipment such as torque wrenches, dial indicators,
feeler gauges, micrometers and calipers according to job
C-9.01.02 select shafts, bearings and seals according to specifications such as product,
operating environment, loads, temperatures, pressures and rpm
C-9.01.03 position shafts, bearings and seals manually or with rigging, hoisting/lifting
and moving equipment
C-9.01.04 mount and fit friction bearings using equipment such as plastigauge, lead
wires, mechanics blue and scrapers
C-9.01.05 mount anti-friction (rolling element-type) bearings using equipment such as
induction heaters, oil baths, arbor presses and bearing ovens
- 37 -
C-9.01.06 secure, level and align shafts, bearings and seals with driven equipment
according to manufacturers and site specifications, and engineered drawings
C-9.01.07 check, adjust and record clearances of bearings and seals according to
manufacturers specifications
C-9.01.08 apply lubricants according to manufacturers specifications
C-9.01.09 remove and reinstall safety guards according to manufacturers specifications
and OH&S regulations
Sub-task
C-9.02 Diagnoses shafts, bearings and seals.
NL NS PE NB QC ON MB SK AB BC NT YT NU
yes yes yes yes NV yes yes yes yes yes NV NV NV
Key Competencies
C-9.02.01 obtain a description of the problem and symptoms
C-9.02.02 perform sensory inspection of shafts, bearings and seals such as listening for
excessive noise, smelling burned components and feeling for excessive
vibration and heat
C-9.02.03 visually inspect for abnormalities such as leaks, missing and loose parts and
damaged components
C-9.02.04 use test/evaluation procedures and specialized equipment according to
results of sensory inspection
C-9.02.05 perform condition-based monitoring routine procedures to detect underlying
defects not identified through sensory inspection
C-9.02.06 verify lubrication level and condition
C-9.02.07 measure clearances in friction and anti-friction (rolling element-type)
bearings
C-9.02.08 assess and detect faulty or damaged equipment to determine next steps such
as repair or replace
C-9.02.09 tag and report faulty or damaged equipment
- 38 -
Sub-task
C-9.03 Repairs shafts, bearings and seals.
NL NS PE NB QC ON MB SK AB BC NT YT NU
yes yes yes yes NV yes yes yes yes yes NV NV NV
Key Competencies
C-9.03.01 rebuild and replace faulty shafts, bearings and seals according to
manufacturers specifications
C-9.03.02 select and use precision measuring tools such as micrometers, torque
wrenches, dial indicators and vernier calipers
C-9.03.03 dismantle, remove and reassemble shafts, bearings and seals to specifications
using tools, procedures match (witness) marks
C-9.03.04 prepare shaft using methods such as sleeving, welding, filing and machining
C-9.03.05 align components according to manufacturers specifications
C-9.03.06 access shafts, bearings and seals by removing components such as housings,
sleeves, snap rings, collars and covers
C-9.03.07 size and replace seals according manufacturers specifications
C-9.03.08 pour and scrape new friction bearings according manufacturers
specifications
C-9.03.09 machine keyway and key seats according manufacturers specifications
Sub-task
C-9.04 Maintains shafts, bearings and seals.
NL NS PE NB QC ON MB SK AB BC NT YT NU
yes yes yes yes NV yes yes yes yes yes NV NV NV
Key Competencies
C-9.04.01 inspect, modify and adjust shafts, bearings and seals according to
maintenance schedule using condition-based monitoring tools
C-9.04.02 check coolant and lubricants levels, packing and seals according to
manufacturers specifications and maintenance schedule
C-9.04.03 monitor temperature, vibration and pressure
C-9.04.04 check automatic bearing and seal lubrication systems
C-9.04.05 adjust flow and pressure controls for cooling and lubrication of sealing
systems according to manufacturers specifications
- 39 -
Task 10 Services couplings, clutches and brakes.
Context Couplings transfer rotary motion from one shaft to another. Clutches
allow engagement and disengagement of power and torque. Brakes
slow or stop the motion.
Required knowledge
K1 clutch and brake faults such as wear, overheating, excessive vibration and
slippage
K2 components of couplings, clutches and brakes
K3 coupling faults such as compromised transfer of movement, excessive
vibration and worn components
K4 indications of component failure such as clutch and brake slippage, excessive
heat and vibration
K5 required clearances and tolerances for couplings, clutches and brakes
K6 setup and operation of couplings, clutches and brakes
K7 types of brakes such as friction and electromagnetic
K8 types of clutches such as overrunning, friction, positive contact and fluid
K9 types of couplings such as rigid, flexible, fluid and electromagnetic
K 10 types of fasteners/retainers such as keys, taper locks, dowels and set screws
K 11 condition-based monitoring technologies such as vibration analysis, UT, fluid
analysis, infrared thermography and motor current analysis
K 12 condition-based monitoring tools such as ultrasonic, strobe lights,
stethoscope, vibration data collectors, infrared cameras and temperature guns
K 13 diagnostic procedures using appropriate condition-based monitoring
technology(ies) and tools
K 14 hazards of working around hazardous friction material
- 40 -
Sub-task
C-10.01 Installs couplings, clutches and brakes.
NL NS PE NB QC ON MB SK AB BC NT YT NU
yes yes yes yes NV yes yes yes yes yes NV NV NV
Key Competencies
C-10.01.01 select and use tools and equipment such as torque wrenches, dial indicators,
feeler gauges, straight edges, micrometers, laser alignment equipment and
calipers according to job
C-10.01.02 select couplings, clutches and brakes according to specifications such as
torque, horsepower, loads, temperatures and rpm
C-10.01.03 position couplings, clutches and brakes manually or with using rigging,
hoisting/lifting and moving equipment
C-10.01.04 assemble couplings, clutches and brakes using tools and equipment such as
presses and pullers, and by heating or cooling the components
C-10.01.05 assemble couplings, clutches and brakes with driven equipment according to
manufacturers and site specifications, and engineered drawings
C-10.01.06 check, adjust and record clearances of couplings, clutches and brakes
according to manufacturers specifications
C-10.01.07 align couplings, clutches and brakes according to manufacturers
specifications
C-10.01.08 lubricate couplings according to manufacturers specifications
C-10.01.09 remove and reinstall safety guards according to manufacturers specifications
and OH&S regulations
C-10.01.10 energize equipment and start-up/return to operations
- 41 -
Sub-task
C-10.02 Diagnoses couplings, clutches and brakes.
NL NS PE NB QC ON MB SK AB BC NT YT NU
yes yes yes yes NV yes yes yes yes yes NV NV NV
Key Competencies
C-10.02.01 obtain a description of the problem and symptoms
C-10.02.02 perform sensory inspection of couplings, clutches and brakes such as
listening for excessive noise, smelling burned components and feeling for
excessive vibration and heat
C-10.02.03 visually inspect for abnormalities such as missing and loose parts, worn and
damaged components
C-10.02.04 select and use tools and equipment such as vernier calipers and condition-
based monitoring tools
C-10.02.05 use test/evaluation procedures such as monitoring temperature and vibration
levels with specialized equipment according to results of sensory inspection
C-10.02.06 perform condition-based monitoring routine procedures to detect underlying
defects not identified through sensory inspection
C-10.02.07 verify lubrication level and condition
C-10.02.08 remove and replace safety guards according to manufacturers and site
specifications
C-10.02.09 measure clearances of brakes and couplings according to manufacturers
specifications
C-10.02.10 assess and detect faulty or damaged components to determine next steps
such as repair or replace
C-10.02.11 tag and report faulty or damaged components
- 42 -
Sub-task
C-10.03 Repairs couplings, clutches and brakes.
NL NS PE NB QC ON MB SK AB BC NT YT NU
yes yes yes yes NV yes yes yes yes yes NV NV NV
Key Competencies
C-10.03.01 rebuild and replace faulty couplings, clutches and brakes according to
manufacturers specifications
C-10.03.02 select and use tools and equipment such as micrometers, hydraulic presses,
pullers, torque wrenches, dial indicators and vernier calipers
C-10.03.03 dismantle, remove and reassemble couplings, clutches and brakes to
specifications using match (witness) marks, and according to procedures
C-10.03.04 recondition couplings and clutches, and broach keyway according
manufacturers specifications
C-10.03.05 access couplings, clutches and brakes by removing safety guards
C-10.03.06 replace coupling components such as springs, grids and elastomeric elements
according to manufacturers specifications
C-10.03.07 replace clutch and brake components such as friction pads, diaphragms and
springs according to manufacturers specifications
C-10.03.08 adjust clutches and brakes according to manufacturers specifications
C-10.03.09 align components according to manufacturers specifications
C-10.03.10 reinstall guards and safety devices according to manufacturers specifications
Context Chain and belt drive systems may be a component of a larger power
transmission system. They transmit power from one shaft to another
and may be used to increase or reduce speed. Proper installation,
alignment and maintenance are key to increasing the reliability of the
system.
Required knowledge
- 43 -
K5 belt faults such as slippage and excessive wear
K6 chain and chain drive components such as sprockets, idlers and links
K7 idler positioning to accommodate arc of contact, tension and slack
K8 indications of chain faults such as noise, vibration and excessive heat
K9 load capacities
K 10 manufacturers' specifications such as tension, rpm, capacity limitations and
operating conditions
K 11 types of belts such as v-belts, timing belts and flat belts
K 12 types of chains such as roller, silent, pintle and detachable
K 13 condition-based monitoring technologies such as vibration analysis, UT, fluid
analysis, infrared thermography and motor current analysis
K 14 condition-based monitoring tools such as belt tension frequency meter, strobe
lights, stethoscope, vibration data collectors, infrared cameras and
temperature guns
K 15 diagnostic procedures using appropriate condition-based monitoring
technology(ies) and tools
Sub-task
C-11.01 Installs chain and belt drive systems.
NL NS PE NB QC ON MB SK AB BC NT YT NU
yes yes yes yes NV yes yes yes yes yes NV NV NV
Key Competencies
C-11.01.01 select and use tools and equipment such as torque wrenches, straight edges
and alignment tools according to job
C-11.01.02 select chain and belt drive systems according to specifications such as torque,
horsepower, loads, temperatures and rpm, and equipment application
C-11.01.03 position chain and belt drive systems manually or with rigging,
hoisting/lifting and moving equipment
C-11.01.04 assemble chain and belt drive systems using tools and equipment such as
presses, tensioners, chain breaks, ropes and pullers
C-11.01.05 align chain and belt drive systems with driven equipment according to
manufacturers and site specifications, and engineered drawings
C-11.01.06 check and adjust tension of chain and belt drive systems according to
manufacturers specifications
C-11.01.07 lubricate chains according to manufacturers specifications
- 44 -
C-11.01.08 remove and reinstall safety guards according to manufacturers specifications
and OH&S regulations
C-11.01.09 energize equipment and start -up/return to operations
Sub-task
C-11.02 Diagnoses chain and belt drive systems.
NL NS PE NB QC ON MB SK AB BC NT YT NU
yes yes yes yes NV yes yes yes yes yes NV NV NV
Key Competencies
C-11.02.01 obtain a description of the problem and symptoms
C-11.02.02 perform sensory inspection of chain and belt drive systems such as listening
for excessive noise, smelling burned components and feeling for excessive
vibration and heat
C-11.02.03 visually inspect for abnormalities such as missing and loose parts, worn and
damaged components
C-11.02.04 use test/evaluation procedures such as monitoring temperature and vibration
levels with specialized equipment according to results of sensory inspection
C-11.02.05 perform condition-based monitoring routine procedures to detect underlying
defects not identified through sensory inspection
C-11.02.06 verify chain lubrication level and condition
C-11.02.07 measure tension of chain and belt drive systems according to manufacturers
specifications
C-11.02.08 assess and detect faulty or damaged components to determine next steps
such as repair or replace
C-11.02.09 tag and report faulty or damaged components
- 45 -
Sub-task
C-11.03 Repairs chain and belt drive systems.
NL NS PE NB QC ON MB SK AB BC NT YT NU
yes yes yes yes NV yes yes yes yes yes NV NV NV
Key Competencies
C-11.03.01 rebuild and replace faulty chains and belt drive systems according to
manufacturers specifications
C-11.03.02 select and use tools and equipment such as hydraulic presses, pullers, torque
wrenches and alignment tools
C-11.03.03 dismantle, remove and reassemble chains and belt drive systems to
manufacturers specifications
C-11.03.04 access chains and belt drive systems by removing safety guards and covers
C-11.03.05 align components such as sprockets and sheaves according to manufacturers
specifications
C-11.03.06 lubricate chain according to site and manufacturers specifications
C-11.03.07 reinstall guards and safety devices according to manufacturers specifications
C-11.03.08 energize equipment and start-up/return to operations
Sub-task
C-11.04 Maintains chain and belt drive systems.
NL NS PE NB QC ON MB SK AB BC NT YT NU
yes yes yes yes NV yes yes yes yes yes NV NV NV
Key Competencies
C-11.04.01 clean, inspect, modify and adjust chain and belt drive systems according to
maintenance schedule using condition-based monitoring tools, tension
gauges and alignment tools
C-11.04.02 check lubricants according to manufacturers specifications and maintenance
schedule
C-11.04.03 check condition of sprockets, sheaves, belts and chains
C-11.04.04 check alignment of sprockets and sheaves according to manufacturers
specifications
C-11.04.05 adjust chain and belt drive systems tension
- 46 -
Task 12 Services gear systems.
Context Gear systems transmit rotary and linear movement from one
component to another and may be used to increase or reduce speed.
Gear systems are used when there is a need for greater versatility such
as speed control, shaft orientation and timing requirements.
Required knowledge
K1 installation sequence
K2 gear faults such as overheating, vibration and excessive noise
K3 gear system components and their installation requirements such as fits,
thrust, clearances and tolerances
K4 gear system components such as shafts, bearings and casings
K5 gear terminology such as pitch diameter, diametral pitch, dedendum,
addendum and working depth
K6 installation methods such as pressed, keyed, sliding and pinned
K7 lubrication methods such as splash, forced and oil rings
K8 simple and compound gear trains
K9 monitoring equipment such as temperature probes and thermographic
equipment, oil analysis, vibration analysis and ultrasound devices
K 10 types of gear systems such as planetary, reduction, and rack and pinion
K 11 types of gears such as spur, herringbone, worm and hypoid
K 12 condition-based monitoring technologies such as vibration analysis, UT, fluid
analysis, infrared thermography and motor current analysis
K 13 condition-based monitoring tools such as strobe lights, stethoscope, vibration
data collectors, infrared cameras and temperature guns
K 14 diagnostic procedures using appropriate condition-based monitoring
technology(ies) and tools
- 47 -
Sub-task
C-12.01 Installs gear systems.
NL NS PE NB QC ON MB SK AB BC NT YT NU
yes yes yes yes NV yes yes yes yes yes NV NV NV
Key Competencies
C-12.01.01 select and use tools and equipment such as torque wrenches, jacks, alignment
tools, blueing and plastigauges according to job
C-12.01.02 select gear systems according to specifications such as torque, horsepower,
loads, temperatures and rpm, and equipment application
C-12.01.03 position gear systems manually or with rigging, hoisting/lifting and moving
equipment
C-12.01.04 assemble gear systems using tools and equipment such as presses and
hydraulic jacks, and by heating and cooling
C-12.01.05 align gear systems with driven and driver equipment according to
manufacturers and site specifications, and engineered drawings
C-12.01.06 check and adjust backlash and tooth contact according to manufacturers
specifications
C-12.01.07 lubricate gear systems according to site and manufacturers specifications
C-12.01.08 remove and reinstall safety guards according to manufacturers specifications
and OH&S regulations
C-12.01.09 energize equipment and start-up/return to operations
Sub-task
C-12.02 Diagnoses gear systems.
NL NS PE NB QC ON MB SK AB BC NT YT NU
yes yes yes yes NV yes yes yes yes yes NV NV NV
Key Competencies
C-12.02.01 obtain a description of the problem and symptoms
C-12.02.02 perform sensory inspection of gear systems such as listening for excessive
noise, smelling burned components and feeling for excessive vibration and
heat
C-12.02.03 visually inspect for abnormalities such as missing and loose parts, worn and
damaged components
- 48 -
C-12.02.04 select and use tools and equipment such as condition-based monitoring tools,
dial indicators and feeler gauges
C-12.02.05 use test/evaluation procedures such as monitoring temperature and vibration
levels with specialized equipment according to results of sensory inspection
C-12.02.06 perform condition-based monitoring routine procedures to detect underlying
defects not identified through sensory inspection
C-12.02.07 verify lubrication level and condition
C-12.02.08 remove and replace safety guards according to site and manufacturers
specifications
C-12.02.09 measure clearance, backlash and tooth contact of gear systems according to
manufacturers specifications
C-12.02.10 assess and detect faulty or damaged components to determine next steps
such as repair or replace
C-12.02.11 tag and report faulty or damaged components
Sub-task
C-12.03 Repairs gear systems.
NL NS PE NB QC ON MB SK AB BC NT YT NU
yes yes yes yes NV yes yes yes yes yes NV NV NV
Key Competencies
C-12.03.01 rebuild and replace faulty gear systems according to manufacturers
specifications
C-12.03.02 select and use tools and equipment such as torque wrenches, jacks, alignment
tools, feeler gauges, mechanics blue and plastigauge
C-12.03.03 access gear systems by removing safety guards and covers
C-12.03.04 dismantle, remove and reassemble gear systems to manufacturers
specifications
C-12.03.05 replace and align gears according to manufacturers specifications
C-12.03.06 adjust gears, backlash, clearance and tooth contact according to
manufacturers specifications
C-12.03.07 lubricate gears according to site and manufacturers specifications
C-12.03.08 reinstall guards and safety devices according to manufacturers specifications
C-12.03.09 energize equipment and start-up/return to operations
- 49 -
Sub-task
C-12.04 Maintains gear systems.
NL NS PE NB QC ON MB SK AB BC NT YT NU
yes yes yes yes NV yes yes yes yes yes NV NV NV
Key Competencies
C-12.04.01 clean, inspect, modify and adjust gear systems according to maintenance
schedule using condition-based monitoring tools and alignment tools
C-12.04.02 check lubricants and seals according to manufacturers specifications and
maintenance schedule
C-12.04.03 check condition of gear systems according to manufacturers specifications
C-12.04.04 check alignment, backlash, clearance and tooth contact of gear systems
according to manufacturers specifications
- 50 -
BLOCK D MATERIAL HANDLING / PROCESS SYSTEMS
Related Fans and Blowers: impellers, rotors, lobes, sheaves, bearings, shafts,
Components seals, bearing housings, fixing rings, gears, couplings, belts, louvers,
(including, but not safety guards.
limited to) Compressors: screws, check valves, pressure relief valves, pressure
regulators, air dryers, sheaves, bearings, shafts, seals, gears, couplings,
belts, safety guards.
Pumps: impellers, sheaves, bearings, shafts, seals, packings, shim packs,
lantern rings, mechanical seals, wear rings, couplings, belts, face plates,
safety guards.
Conveying Systems: couplings, pulleys, clutches, rollers, bearings,
sheaves, backstops, sprockets, chains, belts, buckets, screws, piping,
gear boxes, drive systems, trippers, ploughs, chutes, screens, skirt
boards, filters, safety guards.
Process Tanks and Containers: agitators, filters, mechanical seals,
packings, level and temperature indicators, pumps, valves, liners,
venting systems.
- 51 -
Task 13 Services fans and blowers.
Context Fans and blowers transfer product such as woodchips, waste, exhaust
gases and dust. The failure of fans and blowers can result in safety
issues and lost productivity when not installed, repaired and
maintained properly.
Required Knowledge
- 52 -
Sub-task
D-13.01 Installs fans and blowers.
NL NS PE NB QC ON MB SK AB BC NT YT NU
yes yes yes yes NV yes yes yes yes yes NV NV NV
Key Competencies
D-13.01.01 select and use tools and equipment such as combination wrenches, impact
wrenches, dial indicators, precision levels, and optical or laser alignment
equipment
D-13.01.02 determine location and elevation for installation according to engineered
drawings
D-13.01.03 clean and rough-up base for fan or blower by methods such as filing,
sandblasting and buffing
D-13.01.04 prepare foundation according to engineered drawings
D-13.01.05 position fan or blower in place using rigging, hoisting/lifting and moving
equipment
D-13.01.06 level, align and secure fans and blowers
D-13.01.07 grout to distribute load and minimize vibration
D-13.01.08 check direction of rotation, static and dynamic balance, and vibration
D-13.01.09 connect inlet/outlet
D-13.01.10 connect and align fans and blowers to driver through couplings, sheaves and
belts
D-13.01.11 install safety guards according to manufacturers specifications and OH&S
regulations
D-13.01.12 energize equipment and start-up/return to operations
- 53 -
Sub-task
D-13.02 Diagnoses fans and blowers.
NL NS PE NB QC ON MB SK AB BC NT YT NU
yes yes yes yes NV yes yes yes yes yes NV NV NV
Key Competencies
D-13.02.01 obtain a description of the problem and symptoms
D-13.02.02 perform sensory inspection of components such as sheaves, louvers,
bearings, belts and fan blades
D-13.02.03 use test/evaluation procedures and specialized equipment according to
results of sensory inspection
D-13.02.04 perform condition-based monitoring routine procedures to detect underlying
defects not identified through sensory inspection
D-13.02.05 determine type of repair required such as bearing and coupling replacement,
and re-balancing according to inspection and vibration analysis results
D-13.02.06 identify conditions that led to failure or breakdown of fans and blowers
Sub-task
D-13.03 Repairs fans and blowers.
NL NS PE NB QC ON MB SK AB BC NT YT NU
yes yes yes yes NV yes yes yes yes yes NV NV NV
Key Competencies
D-13.03.01 select and use tools and equipment such as welding machines, hand tools,
and rigging equipment
D-13.03.02 correct imbalances by methods such as cleaning, rebalancing and replacing
bearings
D-13.03.03 replace defective fan and blower components
D-13.03.04 lubricate bearings and couplings
D-13.03.05 energize equipment and start-up/return to operations
- 54 -
Sub-task
D-13.04 Maintains fans and blowers.
NL NS PE NB QC ON MB SK AB BC NT YT NU
yes yes yes yes NV yes yes yes yes yes NV NV NV
Key Competencies
D-13.04.01 perform sensory inspection of fan and blower components using tools such
as tachometers as well as condition-based monitoring tools to locate defects
such as wear, misalignment and debris build-up
D-13.04.02 verify maintenance requirements according to manufacturers specifications
D-13.04.03 clean fan blades
D-13.04.04 lubricate bearings and couplings
D-13.04.05 re-align, replace and adjust fan and blower components
Context Compressors are the source which supplies and controls pressurized air
systems. The failure of compressors can result in safety issues and lost
productivity when not installed, repaired and maintained properly.
Required Knowledge
- 55 -
K 12 condition-based monitoring tools such as strobe lights, stethoscope, vibration
data collectors, infrared cameras and temperature guns
K 13 diagnostic procedures using appropriate condition-based monitoring
technology(ies) and tools
K 14 pressurized air systems and process gas systems
Sub-task
D-14.01 Installs compressors.
NL NS PE NB QC ON MB SK AB BC NT YT NU
yes yes yes yes NV yes yes yes yes yes NV NV NV
Key Competencies
D-14.01.01 select and use tools and equipment such as combination wrenches, impact
wrenches, dial indicators, precision levels, and optical or laser alignment
equipment
D-14.01.02 confirm flow/pressure requirement acccording to engineered drawings and
plant demand
D-14.01.03 determine location and elevation for installation according to engineered
drawings
D-14.01.04 clean and rough-up base for compressor by methods such as filing,
sandblasting and buffing
D-14.01.05 prepare foundation according to engineered drawings
D-14.01.06 position compressor in place using rigging, hoisting/lifting and moving
equipment
D-14.01.07 level, align and secure compressor
D-14.01.08 grout to distribute load and minimize vibration
D-14.01.09 check direction of rotation
D-14.01.10 check for vibration
D-14.01.11 connect inlet/outlet
D-14.01.12 install accessories such as silencers, filters, air dryers, lubricators and
scrubbers
D-14.01.13 connect and align compressors to prime mover through couplings, sheaves
and belts
D-14.01.14 install safety guards according to manufacturers specifications and OH&S
regulations
D-14.01.15 energize equipment and start-up/return to operations
- 56 -
Sub-task
D-14.02 Diagnoses compressors.
NL NS PE NB QC ON MB SK AB BC NT YT NU
yes yes yes yes NV yes yes yes yes yes NV NV NV
Key Competencies
D-14.02.01 obtain a description of the problem and symptoms
D-14.02.02 perform sensory inspection of components such as temperature gauges,
sheaves, piping, valves, bearings and belts
D-14.02.03 use test/evaluation procedures and specialized equipment according to
results of sensory inspection
D-14.02.04 perform condition-based monitoring routine procedures to detect underlying
defects not identified through sensory inspection
D-14.02.05 determine type of repair required such as bearing and coupling replacement,
and refurbishing of valves, according to inspection and vibration analysis
results
D-14.02.06 identify conditions that led to failure or breakdown of compressors
Sub-task
D-14.03 Repairs compressors.
NL NS PE NB QC ON MB SK AB BC NT YT NU
yes yes yes yes NV yes yes yes yes yes NV NV NV
Key Competencies
D-14.03.01 select and use tools and equipment such as hand tools and rigging,
hoisting/lifting and moving equipment
D-14.03.02 refurbish or replace defective compressor components such as impellers,
heads, cross heads, pistons, filters, valves, rings, auto drains and temperature
gauges according to manufacturers specifications
D-14.03.03 lubricate bearings and couplings
D-14.03.04 align prime mover to compressor
D-14.03.05 energize equipment and start-up/return to operations
- 57 -
Sub-task
D-14.04 Maintains compressors.
NL NS PE NB QC ON MB SK AB BC NT YT NU
yes yes yes yes NV yes yes yes yes yes NV NV NV
Key Competencies
D-14.04.01 perform sensory inspection of compressor components using tools such as
tachometers as well as condition-based monitoring tools to locate defects
such as wear and misalignment
D-14.04.02 verify maintenance requirements according to manufacturers specifications
D-14.04.03 clean or replace oil filters and air filters
D-14.04.04 check fluid levels such as coolant, oil and grease
D-14.04.05 check temperatures and pressures
D-14.04.06 re-align drive coupling
D-14.04.07 adjust loading and unloading set points
D-14.04.08 drain moisture from compressors, coolers and receivers
D-14.04.09 verify operation of relief valves, check valves and auto drain valves
Context Pumps are used to move fluid and other media by positive or non-
positive displacement. Proper and safe servicing practices ensure
machine reliability and efficiency. This task includes installation,
diagnosis, repair and maintenance of pumps.
Required Knowledge
- 58 -
K8 manufacturers specifications
K9 product being pumped
K 10 piping and tubing sizing and schematics
K 11 pump terminology such as static head, suction head and suction lift
K 12 prime movers
K 13 condition-based monitoring technologies such as vibration analysis, UT, fluid
analysis, infrared thermography and motor current analysis
K 14 condition-based monitoring tools such as strobe lights, stethoscope, vibration
data collectors, infrared cameras and temperature guns
K 15 diagnostic procedures using appropriate condition-based monitoring
technology(ies) and tools
Sub-task
D-15.01 Installs pumps.
NL NS PE NB QC ON MB SK AB BC NT YT NU
yes yes yes yes NV yes yes yes yes yes NV NV NV
Key Competencies
D-15.01.01 select and use tools and equipment such as torque wrenches, and levelling
and alignment equipment
D-15.01.02 determine location and elevation for installation according to engineered
drawings
D-15.01.03 clean base for pump by methods such as filing, sandblasting and buffing
D-15.01.04 prepare and rough-up foundation according to engineered drawings
D-15.01.05 position pump in place using rigging, hoisting/lifting and moving equipment
D-15.01.06 level, align and secure pump
D-15.01.07 grout to distribute load and minimize vibration
D-15.01.08 set pump clearances according to manufacturers specifications
D-15.01.09 install seals and adjust components such as packings
D-15.01.10 connect inlet/outlet
D-15.01.11 eliminate stress on pump by relieving pipe strain
- 59 -
Sub-task
D-15.02 Diagnoses pumps.
NL NS PE NB QC ON MB SK AB BC NT YT NU
yes yes yes yes NV yes yes yes yes yes NV NV NV
Key Competencies
D-15.02.01 obtain a description of the problem and symptoms
D-15.02.02 perform sensory inspection of pump components such as seals, bearings and
filters for defects such as leaks and noise
D-15.02.03 use test/evaluation procedures such as monitoring temperature and vibration
levels with specialized equipment according to results of sensory inspection
D-15.02.04 perform condition-based monitoring routine procedures to detect underlying
defects not identified through sensory inspection
D-15.02.05 determine type of repair required such as bearing, impeller and coupling
replacement, and refurbishing of valves according to inspection
D-15.02.06 identify conditions that led to failure or breakdown of pumps
Sub-task
D-15.03 Repairs pumps.
NL NS PE NB QC ON MB SK AB BC NT YT NU
yes yes yes yes NV yes yes yes yes yes NV NV NV
Key Competencies
D-15.03.01 select and use tools and equipment such as wrenches, induction heaters and
pullers
D-15.03.02 refurbish or replace defective pump component such as impellers, pistons,
filters, valves, rings, mechanical seals, shafts, couplings, wear rings and
pressure gauges according to manufacturers specifications
D-15.03.03 lubricate bearings and couplings
D-15.03.04 measure component dimensions such as shaft run-out, fits, clearances and
tolerances
- 60 -
Sub-task
D-15.04 Maintains pumps.
NL NS PE NB QC ON MB SK AB BC NT YT NU
yes yes yes yes NV yes yes yes yes yes NV NV NV
Key Competencies
D-15.04.01 perform sensory inspection and use condition-based monitoring tools to
locate defects such as wear and misalignment
D-15.04.02 verify maintenance requirements according to manufacturers specifications
D-15.04.03 clean or replace oil filters and strainers
D-15.04.04 check fluid levels such as coolant, oil and grease
D-15.04.05 check temperatures, vacuum, pressure and flow rates
D-15.04.06 re-align drive coupling
D-15.04.07 verify operation of valves
D-15.04.08 adjust packings and monitor mechanical seals
D-15.04.09 check clearances against manufacturers specifications
Context Conveying systems are used to transfer products safely and efficiently.
This task includes installation, diagnosis, repair and maintenance of
conveying systems.
Required Knowledge
K1 types of mechanical conveying systems such as belt, chain, screw, roller and
bucket
K2 types of pneumatic and hydraulic conveying systems such as low pressure
and high pressure
K3 conveying system accessories such as trippers, ploughs, chutes, screens, skirt
boards and flights
K4 conveying system faults such as belt tracking, worn components and
improper tension
K5 conveying system specifications such as speed, distance travelled and load
weight
K6 conveyor components such as scrapers, bearings, sprockets, chains, belts and
counter-weight assemblies
- 61 -
K7 types of filters such as cyclones, bag shakers and precipitators
K8 types of pulleys and rollers such as crowned, tail, take-up, tracking, idler and
snub
K9 types of gear boxes
K 10 manufacturers specifications
K 11 material to be conveyed
K 12 condition-based monitoring technologies such as vibration analysis, UT, fluid
analysis, infrared thermography and motor current analysis
K 13 condition-based monitoring tools such as strobe lights, stethoscope, vibration
data collectors, infrared cameras and temperature guns
K 14 diagnostic procedures using appropriate condition-based monitoring
technology(ies) and tools
Sub-task
D-16.01 Installs conveying systems.
NL NS PE NB QC ON MB SK AB BC NT YT NU
yes yes yes yes NV yes yes yes yes yes NV NV NV
Key Competencies
D-16.01.01 select and use tools and equipment such as hand tools, and levelling and
alignment equipment
D-16.01.02 determine location and elevation for installation according to engineered
drawings
D-16.01.03 prepare base or mounting brackets according to design specifications and
type of installation
D-16.01.04 prepare foundation according to engineered drawings
D-16.01.05 assemble conveying system according to design specifications
D-16.01.06 install conveyor components such as bearings, pulleys, rollers, gear reduction
units and take-ups
D-16.01.07 position conveying system in place using rigging, hoisting/lifting and moving
equipment
D-16.01.08 align, level and secure conveying system according to type
D-16.01.09 grout to distribute load and minimize vibration
D-16.01.10 set clearances according to manufacturers specifications
D-16.01.11 check direction of rotation
D-16.01.12 connect in-feed and discharge
- 62 -
D-16.01.13 connect belts using splicing techniques such as vulcanizing, cold splicing and
applying mechanical fasteners
D-16.01.14 connect chains using components such as connecting links, rivets and locking
clips
D-16.01.15 connect and align prime mover through couplings, sheaves and belts
D-16.01.16 install sensory devices such as motion detectors and depth sensors
D-16.01.17 install safety guards according to manufacturers specifications and OH&S
regulations
D-16.01.18 energize equipment and start-up/return to operation
Sub-task
D-16.02 Diagnoses conveying systems.
NL NS PE NB QC ON MB SK AB BC NT YT NU
yes yes yes yes NV yes yes yes yes yes NV NV NV
Key Competencies
D-16.02.01 obtain a description of the problem and symptoms
D-16.02.02 perform sensory inspection of components such as limit switches, gear
reduction units, emergency stops, couplings, magnets, pulleys, rollers,
bearings, sheaves, sprockets, chains and belts
D-16.02.03 perform sensory inspection of filters such as cyclones, bag shakers, screens
and precipitators
D-16.02.04 select and use tools and equipment such as hand tools, and levelling and
alignment equipment to locate and troubleshoot defects
D-16.02.05 use test/evaluation procedures such as monitoring temperature and vibration
levels with specialized equipment according to results of sensory inspection
D-16.02.06 perform condition-based monitoring routine procedures to detect underlying
defects not identified through sensory inspection
D-16.02.07 determine type of repair required such as bearings, couplings, idlers,
conveyor belts, mechanical splices, and rotary valve replacement according to
inspection
D-16.02.08 identify conditions that led to failure or breakdown of conveying system
- 63 -
Sub-task
D-16.03 Repairs conveying systems.
NL NS PE NB QC ON MB SK AB BC NT YT NU
yes yes yes yes NV yes yes yes yes yes NV NV NV
Key Competencies
D-16.03.01 select and use tools and equipment such as hand tools, saws, and hoisting/
lifting and rigging equipment
D-16.03.02 refurbish or replace defective conveying system components such as gear
reduction units, couplings, pulleys, rollers, bearings, sheaves, sprockets,
screens, chains, skirting and belts according to manufacturers specifications
D-16.03.03 lubricate bearings and couplings
D-16.03.04 align prime mover to conveyor system
D-16.03.05 connect belts using splicing techniques such as vulcanizing, cold splicing and
applying mechanical fasteners
D-16.03.06 connect chains using components such as connecting links, rivets and locking
clips
D-16.03.07 correct tracking issues with belt
D-16.03.08 energize equipment and start-up/return to operation
Sub-task
D-16.04 Maintains conveying systems.
NL NS PE NB QC ON MB SK AB BC NT YT NU
yes yes yes yes NV yes yes yes yes yes NV NV NV
Key Competencies
D-16.04.01 perform sensory inspection and use tools and equipment such as wrenches
and tachometers as well as condition-based monitoring tools, to locate defects
such as wear and misalignment
D-16.04.02 verify maintenance requirements according to manufacturers specifications
D-16.04.03 check fluid levels such as oil and grease
D-16.04.04 check temperatures
D-16.04.05 re-align drive coupling
D-16.04.06 check clearances against manufacturers specifications
D-16.04.07 maintain components by methods such as cleaning, lubricating and adjusting
- 64 -
D-16.04.08 maintain drive components by methods such as checking fluid levels and
tensioning according to type of drive
D-16.04.09 adjust tracking of mechanical conveying systems
D-16.04.10 adjust conveying system accessories such as belt scraper, guides and training
idlers
D-16.04.11 replace filters
Context Process tanks and containers are usually used to store and mix
materials. Tanks and containers may be pressurized or open to
atmosphere. This task includes installation, diagnosis, repair and
maintenance of process tanks and containers such as bins and hoppers.
Required Knowledge
K1 types of process tanks and containers such as pressurized vessels and storage
tanks
K2 process tank and container components such as piping, agitators, vents,
pumps, compressors, blowers and level indicators
K3 process tank and container specifications such as capacity and compatibility
K4 material to be held and holding requirements such as corrosion resistance,
tank pressures and temperature
K5 piping schematics
K6 environmental containment systems
K7 hazards of and procedures for working in confined spaces
K8 process tank and container faults such as leaks, and loss of or excess pressure
K9 jurisdictional regulations governing steam and pressure vessels
K 10 cleaning requirements
K 11 diagnostic procedures and tools such as NDT
K 12 condition-based monitoring technologies such as vibration analysis, UT, fluid
analysis and infrared thermography
K 13 condition-based monitoring tools such as strobe lights, stethoscope, vibration
data collectors, infrared cameras and temperature guns
K 14 diagnostic procedures using appropriate condition-based monitoring
technology(ies) and tools
K 15 vessel integrity and thickness testing (tank access to top/lid)
- 65 -
Sub-task
D-17.01 Installs process tanks and containers.
NL NS PE NB QC ON MB SK AB BC NT YT NU
yes yes yes yes NV yes yes yes yes yes NV NV NV
Key Competencies
D-17.01.01 select and use tools and equipment such as layout and levelling tools
D-17.01.02 determine location and elevation for installation according to engineered
drawings
D-17.01.03 clean base for process tanks and containers by methods such as filing,
sandblasting and buffing
D-17.01.04 prepare and rough-up foundation according to engineered drawings
D-17.01.05 position process tanks and containers in place using rigging, hoisting/lifting
and moving equipment
D-17.01.06 level, align and secure process tanks and containers
D-17.01.07 check orientation of tank
D-17.01.08 grout to distribute load and minimize vibration
D-17.01.09 connect inlet/outlet
D-17.01.10 install components such as agitators, impellers, scrapers and mixers
D-17.01.11 install safety guards according to manufacturers specifications and OH&S
regulations
Sub-task
D-17.02 Diagnoses process tanks and containers.
NL NS PE NB QC ON MB SK AB BC NT YT NU
yes yes yes yes NV yes yes yes yes yes NV NV NV
Key Competencies
D-17.02.01 obtain a description of the problem and symptoms
D-17.02.02 perform sensory inspection of components such as filters, strainers, piping,
agitators, vents and level indicators
D-17.02.03 determine if NDT or condition-based monitoring is required according to the
results of sensory inspection
D-17.02.04 perform condition-based monitoring routine procedures to detect underlying
defects not identified through sensory inspection
- 66 -
D-17.02.05 determine type of repair required such as patching, overlay, re-coating and
piping according to inspection and analysis results
D-17.02.06 identify conditions that led to failure or breakdown of process tanks and
containers
Sub-task
D-17.03 Repairs process tanks and containers.
NL NS PE NB QC ON MB SK AB BC NT YT NU
yes yes yes yes NV yes yes yes yes yes NV NV NV
Key Competencies
D-17.03.01 select and use tools and equipment such as hand tools and welding
equipment
D-17.03.02 refurbish or replace defective components such as piping, agitators, vents,
liners, seals and level indicators
D-17.03.03 measure component dimensions such as piping and length of shaft
D-17.03.04 adjust components such as agitators and mixers
D-17.03.05 lubricate components such as agitators, pull chains and mixers
Sub-task
D-17.04 Maintains process tanks and containers.
NL NS PE NB QC ON MB SK AB BC NT YT NU
yes yes yes yes NV yes yes yes yes yes NV NV NV
Key Competencies
D-17.04.01 perform sensory inspection as well as use condition-based monitoring tools
and NDT to locate defects such as leaks and wear
D-17.04.02 verify maintenance requirements according to manufacturers specifications
D-17.04.03 clean or replace oil filters and strainers
D-17.04.04 check fluid levels such as coolant, oil and grease
D-17.04.05 check temperatures, pressures, vacuum and flow rates
D-17.04.06 verify operation of valves
D-17.04.07 adjust process tank and container components by setting pressure relief
valves and patching holes
- 67 -
D-17.04.08 check clearances of components such as agitators according to manufacturers
specifications
D-17.04.09 change liners
D-17.04.10 clear ventilation systems of blockages
- 68 -
BLOCK E HYDRAULIC, PNEUMATIC AND VACUUM
SYSTEMS
Context Hydraulic systems are versatile systems that use high pressure fluids to
transmit power in a variety of industries. Industrial mechanics
(millwrights) service these systems to ensure proper and efficient
operation.
Required Knowledge
- 69 -
K 10 hydraulic system faults such as loss of pressure, cavitations, contamination of
fluid, aeration, leaks, loss of movement and speed, and overheating
K 11 basic electrical principles
K 12 trade calculations and theories such as Bernoullis principle and Pascals law
K 13 hydraulic system components such as pumps, control valves and actuators
K 14 types of valves such as directional control, flow control and pressure control
K 15 hazards and isolating procedures associated with high pressure fluids, zero
energy and stored energy
K 16 operation of primary components such as actuators, pumps and valves
K 17 fluid conductors such as hoses, piping and tubing
K 18 types of fluids such as petroleum-based, fire resistant, food grade and
environmentally friendly and synthetic
K 19 system operating parameters such as temperature, pressure and flow
K 20 filters, strainers and related contamination control equipment
K 21 basic control functions
K 22 programmable logic controller (PLC) operating principles
K 23 condition-based monitoring technologies such as vibration analysis, UT, fluid
analysis, infrared thermography and motor current analysis
K 24 condition-based monitoring tools such as strobe lights, stethoscope, vibration
data collectors, infrared cameras and temperature guns
K 25 diagnostic procedures using appropriate condition-based monitoring
technology(ies) and tools
Sub-task
E-18.01 Installs hydraulic systems.
NL NS PE NB QC ON MB SK AB BC NT YT NU
yes yes yes yes NV yes yes yes yes yes NV NV NV
Key Competencies
E-18.01.01 select and use tools and equipment such as torque wrenches, pressure gauges
and hand tools
E-18.01.02 select system components such as pumps, valves, actuators, reservoirs, hoses,
seals, fittings, strainers and filters according to schematics and job
specifications
E-18.01.03 select hydraulic fluids to meet site and system requirements
E-18.01.04 position and secure reservoirs for hydraulic systems according to schematics,
manually or with rigging, hoisting/lifting and moving equipment
- 70 -
E-18.01.05 position, align and secure hydraulic pumps and motors according to
schematics, manually or with rigging, hoisting/lifting and moving equipment
E-18.01.06 install components such as filters, strainers, hydraulic valves, actuators and
motors according to schematics, manually or with rigging, hoisting/lifting
and moving equipment
E-18.01.07 measure, cut, bend and connect piping, hoses and tubing according to
schematics
E-18.01.08 test system by fine tuning pressure and fluid flow operation prior to start-up
Sub-task
E-18.02 Diagnoses hydraulic systems.
NL NS PE NB QC ON MB SK AB BC NT YT NU
yes yes yes yes NV yes yes yes yes yes NV NV NV
Key Competencies
E-18.02.01 obtain a description of the problem and symptoms
E-18.02.02 perform sensory inspection of hydraulic systems such as listening for
excessive noise, smelling burned components and feeling for excessive
vibration
E-18.02.03 visually inspect for leaks, abnormal movements and oil conditions, and fluid
levels
E-18.02.04 use test/evaluation procedures and specialized equipment according to
results of sensory inspection
E-18.02.05 perform condition-based monitoring routine procedures to detect underlying
defects not identified through sensory inspection
E-18.02.06 interpret specifications from technical manuals
E-18.02.07 inspect hydraulic systems to identify faults such as pressure and speed drop
or increase
E-18.02.08 identify components that require repair or replacement
E-18.02.09 record hydraulic data
- 71 -
Sub-task
E-18.03 Repairs hydraulic systems.
NL NS PE NB QC ON MB SK AB BC NT YT NU
yes yes yes yes NV yes yes yes yes yes NV NV NV
Key Competencies
E-18.03.01 release pressure to ensure system or system component is in a zero energy
state
E-18.03.02 mechanically lock the components in place.
E-18.03.03 prevent contamination during repairs by ensuring clean components
E-18.03.04 repair and replace components such as actuators, pumps, filters and valves
E-18.03.05 remove and replace component parts such as seals, pistons and valve spools
E-18.03.06 modify systems according to schematics
E-18.03.07 test system by fine tuning pressure and fluid flow operation prior to
returning to service
Sub-task
E-18.04 Maintains hydraulic systems.
NL NS PE NB QC ON MB SK AB BC NT YT NU
yes yes yes yes NV yes yes yes yes yes NV NV NV
Key Competencies
E-18.04.01 perform sensory inspection of hydraulic systems as well as use condition-
based monitoring tools to detect defects
E-18.04.02 verify and adjust fluid levels according to site and manufacturers
specifications
E-18.04.03 check and adjust system pressure, temperature and flow according to
manufacturers specifications
E-18.04.04 check and change filters according to manufacturers specifications
E-18.04.05 assess overall performance of hydraulic systems according to performance
specifications
E-18.04.06 clean hydraulic systems and components
E-18.04.07 record maintenance results
- 72 -
Task 19 Services pneumatic and vacuum systems.
Context Pneumatic and vacuum systems provide control and power for
mechanical and process systems. Industrial mechanics (millwrights) are
responsible for the installation, diagnosis, repair and maintenance of
these systems.
Required Knowledge
- 73 -
K 22 condition-based monitoring tools such as strobe lights, stethoscope, vibration
data collectors, infrared cameras and temperature guns
K 23 diagnostic procedures using appropriate condition-based monitoring
technology(ies) and tools
Sub-task
E-19.01 Installs pneumatic and vacuum systems.
NL NS PE NB QC ON MB SK AB BC NT YT NU
yes yes yes yes NV yes yes yes yes yes NV NV NV
Key Competencies
E-19.01.01 obtain a description of the problem and symptoms
E-19.01.02 select and use tools and equipment such as torque wrenches,
pressure/vacuum gauges and hand tools
E-19.01.03 select system components such as hoses, seals, fittings, strainers and filters
according to schematics and job specifications
E-19.01.04 position and secure components such as receivers, tanks and accumulators
for pneumatic and vacuum systems according to schematics, manually or
with rigging, hoisting/lifting and moving equipment
E-19.01.05 position, align and secure blowers, compressors, vacuum pumps and motors
according to schematics, manually or with rigging, hoisting/lifting and
moving equipment
E-19.01.06 measure, cut, bend and connect piping, hoses and tubing according to
schematics
E-19.01.07 test system by fine tuning pressure and vacuum prior to start-up
- 74 -
Sub-task
E-19.02 Diagnoses pneumatic and vacuum systems.
NL NS PE NB QC ON MB SK AB BC NT YT NU
yes yes yes yes NV yes yes yes yes yes NV NV NV
Key Competencies
E-19.02.01 perform sensory inspection of pneumatic and vacuum systems such as
listening for excessive noise, smelling burned components and feeling for
excessive vibration
E-19.02.02 visually inspect for leaks, abnormal movements and oil conditions, and fluid
levels
E-19.02.03 use test/evaluation procedures and specialized equipment according to
results of sensory inspection
E-19.02.04 perform condition-based monitoring routine procedures to detect underlying
defects not identified through sensory inspection
E-19.02.05 interpret specifications from technical manuals
E-19.02.06 inspect pneumatic and vacuum systems to identify faults such as pressure,
vacuum and speed variance
E-19.02.07 identify components that require repair or replacement
E-19.02.08 record pneumatic and vacuum data
Sub-task
E-19.03 Repairs pneumatic and vacuum systems.
NL NS PE NB QC ON MB SK AB BC NT YT NU
yes yes yes yes NV yes yes yes yes yes NV NV NV
Key Competencies
E-19.03.01 release pressure to ensure system or system component is in a zero energy
state
E-19.03.02 mechanically lock the components in place
E-19.03.03 prevent contamination during repairs by ensuring clean components
E-19.03.04 repair and replace components such as blowers, compressors, vacuum
pumps, motors, valves and actuators according to site and manufacturers
specifications
E-19.03.05 remove and replace component parts such as filters, seals, strainers, dryers,
lubricators and regulators
- 75 -
E-19.03.06 tighten components such as hoses, seals, fittings and flanges according to
manufacturers specifications
E-19.03.07 test system by fine tuning pressure and vacuum prior to returning to service
Sub-task
E-19.04 Maintains pneumatic and vacuum systems.
NL NS PE NB QC ON MB SK AB BC NT YT NU
yes yes yes yes NV yes yes yes yes yes NV NV NV
Key Competencies
E-19.04.01 perform sensory inspection of pneumatic and vacuum systems as well as use
condition-based monitoring tools to detect defects
E-19.04.02 verify and adjust fluid levels according to site and manufacturers
specifications
E-19.04.03 check and adjust system pressure, vacuum, lubricators, regulators,
temperature, cycling and flow according to manufacturers specifications
E-19.04.04 check and change gauges, filters and dryers according to manufacturers
specifications
E-19.04.05 assess overall performance of pneumatic and vacuum systems according to
performance specifications
E-19.04.06 clean pneumatic and vacuum systems and components
E-19.04.07 record maintenance results
E-19.04.08 modify system to accommodate a change in requirements according to
schematics
- 76 -
BLOCK F PREVENTIVE AND PREDICTIVE MAINTENANCE,
TESTING AND COMMISSIONING
Required Knowledge
- 77 -
K4 specialized predictive maintenance tools such as data collectors and
computerized maintenance management systems (CMMS)
K5 specialized tools and equipment such as ultrasound grease guns
K6 safe use and operation of specialized tools and equipment (awareness of
surrounding)
K7 maintenance history of equipment
K8 manufacturers specifications
K9 condition-based monitoring technologies such as vibration analysis, UT, fluid
analysis, infrared thermography and motor current analysis
K 10 condition-based monitoring tools such as strobe lights, stethoscope, vibration
data collectors, infrared cameras and temperature guns
Sub-task
F-20.01 Performs preventive maintenance activities.
NL NS PE NB QC ON MB SK AB BC NT YT NU
yes yes yes yes NV yes yes yes yes yes NV NV NV
Key Competencies
F-20.01.01 perform sensory inspections of machinery, equipment and components at
predetermined scheduled intervals to detect abnormalities such as change in
pitch, rattling, cracks, loose bolts and leaks
F-20.01.02 perform hands-on inspections like checking tolerances and clearances of
machinery, equipment and components using tools such as hand tools,
gauges and strobe lights
F-20.01.03 check for worn, defective, broken or otherwise unacceptable components
such as filters, sight glasses, packing, seals, bearings and gaskets
F-20.01.04 check condition, level and temperature of fluids according to manufacturers
recommendations
F-20.01.05 grease and lubricate components according to site, manufacturers or
engineers specifications
F-20.01.06 adjust tension on components such as belts, chains and tie rods
F-20.01.07 record information for future equipment evaluation and eventual repair
- 78 -
Sub-task
F-20.02 Performs predictive maintenance activities.
NL NS PE NB QC ON MB SK AB BC NT YT NU
yes yes yes yes NV yes yes yes yes yes NV NV NV
Key Competencies
F-20.02.01 select specialized tools and equipment to use based on their applications and
limitations, and the required accuracy of the result
F-20.02.02 select NDT to be used such as dye penetrant, infrared, ultrasound and
magnetic particle based on the characteristics of the machinery, equipment or
component being tested
F-20.02.03 detect faults, frequencies or defects in the machinery or the equipment by
reviewing spectrums, graphs, logbooks, lab reports and images
F-20.02.04 record information for future equipment evaluation and eventual repair
Sub-task
F-20.03 Schedules preventive and predictive maintenance.
NL NS PE NB QC ON MB SK AB BC NT YT NU
yes yes yes yes NV yes yes yes yes no NV NV NV
Key Competencies
F-20.03.01 determine equipments criticality and its failure history, or its life expectancy
if no history exists by referring to CMMS, similar technology, duplicate
equipment on or off-site, design drawings and manufacturers
recommendations
F-20.03.02 review collected data to determine suitable maintenance schedules
- 79 -
Task 21 Performs specialized testing and analysis.
Required Knowledge
K1 CMMS
K2 preventive and predictive maintenance programs and schedules
K3 rotating and non-rotating equipment faults
K4 vibration, ultrasound, infrared and tribology theory
K5 types of fluids to be tested such as oil, glycol and grease
K6 sample collection techniques
K7 types of analyzers and transducers and their applications
K8 types of internal components on which data is being collected
K9 data collection points
K 10 NDT techniques such as dye penetrant, magnetic particle, radiography and
ultrasonic
K 11 testing techniques such as particle count, filter patch, ferrography and
viscosity
K 12 types of imbalance such as static, dynamic and coupled
K 13 manufacturers and company-specific specifications for balancing
K 14 balancing machines and analyzing equipment
K 15 static and dynamic balancing procedures
K 16 single- and multi-plane balancing methods
K 17 alignment procedures
K 18 types of misalignment such as horizontal, vertical and angular
K 19 benefit of properly balanced and aligned equipment
K 20 ferrous and non-ferrous properties
- 80 -
Sub-task
F-21.01 Performs vibration analysis procedures.
NL NS PE NB QC ON MB SK AB BC NT YT NU
yes yes yes yes NV yes yes yes yes no NV NV NV
Key Competencies
F-21.01.01 select vibration analyzing equipment and software depending on application
such as overall vibration analysis, modal analysis and operational deflection
shape (ODS) analysis
F-21.01.02 install the necessary manufacturer components to achieve consistent readings
at predetermined access points
F-21.01.03 set parameters of software for desired data collection
F-21.01.04 collect readings at consistent points across rotating and non-rotating
equipment
F-21.01.05 identify vibration frequencies related to type of internal components on
which data is being collected
F-21.01.06 identify causes of vibration such as eccentricity, misalignment and shaft
faults based on interpretation of data collected
Sub-task
F-21.02 Performs balancing procedures.
NL NS PE NB QC ON MB SK AB BC NT YT NU
yes yes yes yes NV yes yes yes yes yes NV NV NV
Key Competencies
F-21.02.01 clean machinery/equipment to confirm if balancing is necessary
F-21.02.02 inspect machinery or equipment for defects such as missing buckets, broken
fins, bent shafts, missing weights and loose fit
F-21.02.03 use balancing equipment such as hand-held devices and shop balancing
machines to determine location of imbalance
F-21.02.04 identify type of imbalance in equipment and machinery to determine
corrective action needed
F-21.02.05 add and/or remove specific weights at identified locations to meet
specifications
- 81 -
Sub-task
F-21.03 Performs alignment procedures.
NL NS PE NB QC ON MB SK AB BC NT YT NU
yes yes yes yes NV yes yes yes yes yes NV NV NV
Key Competencies
F-21.03.01 clean machinery or equipment to avoid false readings
F-21.03.02 inspect machinery or equipment for defects such as loose bolts, cracked
foundations and pipe strain
F-21.03.03 select and use alignment tools such as feeler gauges, straightedges, dial
indicators and laser alignment devices to determine degree of misalignment
F-21.03.04 identify cause of misalignment in equipment and machinery to determine
corrective action needed
F-21.03.05 correct vertical, horizontal and angular misalignment, and soft foot of direct
drive equipment by adding and/or removing shims, and/or by adjusting the
angular position of the driver/driven equipment
F-21.03.06 correct misalignment of driver/driven sprockets or sheaves by adjusting their
position
F-21.03.07 record alignment data to demonstrate compliance
Sub-task
F-21.04 Performs non-destructive testing (NDT) procedures.
NL NS PE NB QC ON MB SK AB BC NT YT NU
yes yes yes yes NV yes yes yes yes no NV NV NV
Key Competencies
F-21.04.01 prepare the equipment for testing by cleaning, removing paint or rust to
avoid false readings
F-21.04.02 select NDT method based on equipment characteristics (ferrous/non-ferrous)
and results required to detect faults such as cracks, thin walls and inclusions
F-21.04.03 determine hardness of material to confirm it meets specifications for intended
purpose
F-21.04.04 follow dye penetrant procedures to expose cracks in ferrous and non-ferrous
materials caused by fatigue, improper welding or impurities
- 82 -
Sub-task
F-21.05 Performs fluid analysis procedures.
NL NS PE NB QC ON MB SK AB BC NT YT NU
yes yes yes yes NV yes yes yes yes yes NV NV NV
Key Competencies
F-21.05.01 perform sensory inspections of fluid condition to detect abnormalities such as
change in colour and odour, presence of sludge and impurities
F-21.05.02 determine location and frequency of sample collection using established best
procedures to ensure reliability of current and future results
F-21.05.03 interpret external test report information such as contamination, abnormal
viscosity and wear particles
F-21.05.04 direct information for corrective action
Required Knowledge
- 83 -
Sub-task
F-22.01 Commissions mechanical systems and components, and material
handling/process systems.
NL NS PE NB QC ON MB SK AB BC NT YT NU
yes yes yes yes NV yes yes yes yes yes NV NV NV
Key Competencies
F-22.01.01 review check list to ensure that rotational checks and all other procedures
have been completed according to engineering and manufacturers
specifications
F-22.01.02 check safety components such as guards, emergency stops and overrun
switches
F-22.01.03 start-up and run-in systems and equipment in predetermined order
according to type and design of system
F-22.01.04 perform monitoring activities such as packing adjustments and alignments
F-22.01.05 re-torque bolts such as anchor, base, flanges, bull gears and pinions after
manufacturers recommended run-in period
F-22.01.06 confirm alignment, such as hot alignment from steam turbines and hot/cold
fluids, of equipment after manufacturers recommended run-in period
F-22.01.07 perform baseline readings on preliminary tests such as vibration, fluids,
ultrasound and infrared
Sub-task
F-22.02 Commissions hydraulic, pneumatic and vacuum systems.
NL NS PE NB QC ON MB SK AB BC NT YT NU
yes yes yes yes NV yes yes yes yes yes NV NV NV
Key Competencies
F-22.02.01 review check list to ensure that rotational checks and all other procedures
have been completed according to engineering and manufacturers
specifications
F-22.02.02 check safety components such as guards, emergency stops and overrun
switches
F-22.02.03 start-up and run-in systems and equipment in predetermined order
according to type and design of system
F-22.02.04 perform monitoring activities such as packing adjustments and alignments
- 84 -
F-22.02.05 re-torque bolts such as anchor, base, flanges and cylinder heads after
manufacturers recommended run-in period
F-22.02.06 confirm alignment of motors and pumps after manufacturers recommended
run-in period
F-22.02.07 perform baseline readings on preliminary tests such as vibration, fluids,
ultrasound and infrared
- 85 -
APPENDICES
APPENDIX A TOOLS AND EQUIPMENT
Hand Tools
- 89 -
Measuring and Layout Tools (continued)
- 90 -
Testing Equipment
- 91 -
Resource Materials
- 92 -
APPENDIX B GLOSSARY
agitator a device which keeps material moving in a tank or vessel; the movement may
be required to prevent settling and to mix material
arc of contact surface contact between the sheave and pulley and the belt, or the sprocket and
the chain
bearing device that allows two parts to rotate or move in contact with each other
blower device that moves air at low or high pressures and volumes
centrifugal flow to flow 90 degrees to the axis of a fan or a pump away from the centre
conveying system used to move material (usually solid) from one place to another
systems
engineered lift consulting an engineer for an approved design of a lifting apparatus or lifting
procedure without exceeding the rated capacity of the rigging equipment; it
should be noted that this is generally done when unusual circumstances of a lift
dictate deviations from normal accepted trade practices
fluid substance (either a liquid or gas) material that has the ability to flow
gear system combination of gears used to alter the speed and power from a driver to a
driven unit
- 93 -
maintain keeping a machine or system running efficiently with a minimum amount of
down-time; ror use in this analysis the term maintain can encompass:
checking for worn parts, lubrication, adjustment, inspection and modification
manufacturers refers to the performance and engineering standards for a particular machine
specifications as detailed by the manufacturer; this information is usually available from
drawings, manuals and bulletins provided by the manufacturer
multi-plane to balance a rotating part on more than two planes; multi-plane balancing is
balancing usually performed with computer software that is usually provided with
vibration analysis and balancing instruments
non-destructive testing procedures that do not damage the material being tested; these may
testing (NDT) include magnetic particle testing, dye penetrant testing, and fluid sampling
predictive activities utilizing information from past and current performance records to
maintenance objectively predict mechanical problems; predictive maintenance is a proactive
monitoring approach rather than a time-based or reactive approach
prime mover driver of the machine; it may be an electric, steam, gas or diesel powered
service for use in this analysis the term service refers to installing, diagnosing,
repairing and maintaining
vibration analysis the process of monitoring the condition of equipment and the diagnosis of
faults in equipment through the measurement and analysis of vibration within
that equipment
- 94 -
APPENDIX C ACRONYMS
GMAW gas metal arc welding (also known as metal inert gas [MIG] welding)
GTAW gas tungsten arc welding (also known as tungsten inert gas [TIG] welding)
UT ultrasonic technology
- 95 -
APPENDIX D BLOCK AND TASK WEIGHTING
National
NL NS PE NB QC ON MB SK AB BC NT YT NU Average
% 20 11 13 9 NV 20 20 16 20 10 NV NV NV
15%
NL NS PE NB QC ON MB SK AB BC NT YT NU
21%
% 25 21 25 20 NV 25 25 22 15 8 NV NV NV
NL NS PE NB QC ON MB SK AB BC NT YT NU
20%
% 20 17 15 24 NV 30 15 26 20 12 NV NV NV
NL NS PE NB QC ON MB SK AB BC NT YT NU
25%
% 20 27 20 26 NV 25 15 21 50 25 NV NV NV
NL NS PE NB QC ON MB SK AB BC NT YT NU
18%
% 20 20 20 18 NV 10 15 19 10 30 NV NV NV
NL NS PE NB QC ON MB SK AB BC NT YT NU
16%
% 15 15 20 12 NV 10 30 12 5 25 NV NV NV
- 96 -
BLOCK B RIGGING, HOISTING/LIFTING AND MOVING
National
NL NS PE NB QC ON MB SK AB BC NT YT NU Average
% 20 12 12 21 NV 10 10 14 10 15 NV NV NV
14%
NL NS PE NB QC ON MB SK AB BC NT YT NU
50%
% 50 35 50 50 NV 70 70 46 15 60 NV NV NV
NL NS PE NB QC ON MB SK AB BC NT YT NU
50%
% 50 65 50 50 NV 30 30 54 85 40 NV NV NV
National
NL NS PE NB QC ON MB SK AB BC NT YT NU Average
% 20 27 20 24 NV 26 25 25 20 30 NV NV NV
24%
NL NS PE NB QC ON MB SK AB BC NT YT NU
20%
% 20 25 20 14 NV 10 24 27 20 20 NV NV NV
NL NS PE NB QC ON MB SK AB BC NT YT NU
24%
% 25 23 20 24 NV 30 25 22 20 30 NV NV NV
NL NS PE NB QC ON MB SK AB BC NT YT NU
20%
% 25 18 20 26 NV 15 25 16 20 15 NV NV NV
- 97 -
Task 11 Services chain and belt drive systems.
NL NS PE NB QC ON MB SK AB BC NT YT NU
19%
% 15 16 20 22 NV 27 13 20 20 20 NV NV NV
NL NS PE NB QC ON MB SK AB BC NT YT NU
17%
% 15 18 20 14 NV 18 13 15 20 15 NV NV NV
National
NL NS PE NB QC ON MB SK AB BC NT YT NU Average
% 20 20 20 18 NV 21 25 20 20 25 NV NV NV
21%
NL NS PE NB QC ON MB SK AB BC NT YT NU
17%
% 15 15 20 16 NV 15 20 19 20 15 NV NV NV
NL NS PE NB QC ON MB SK AB BC NT YT NU
19%
% 20 27 20 23 NV 10 20 19 20 15 NV NV NV
NL NS PE NB QC ON MB SK AB BC NT YT NU
28%
% 30 25 25 26 NV 30 30 31 20 30 NV NV NV
NL NS PE NB QC ON MB SK AB BC NT YT NU
25%
% 25 23 25 26 NV 30 20 18 20 35 NV NV NV
NL NS PE NB QC ON MB SK AB BC NT YT NU
11%
% 10 10 10 9 NV 15 10 13 20 5 NV NV NV
- 98 -
BLOCK E HYDRAULIC, PNEUMATIC AND VACUUM SYSTEMS
National
NL NS PE NB QC ON MB SK AB BC NT YT NU Average
% 10 20 17 18 NV 10 10 17 15 15 NV NV NV
15%
NL NS PE NB QC ON MB SK AB BC NT YT NU
55%
% 50 60 50 50 NV 50 60 55 60 60 NV NV NV
NL NS PE NB QC ON MB SK AB BC NT YT NU
45%
% 50 40 50 50 NV 50 40 45 40 40 NV NV NV
National
NL NS PE NB QC ON MB SK AB BC NT YT NU Average
% 10 10 18 10 NV 13 10 8 15 5 NV NV NV
11%
NL NS PE NB QC ON MB SK AB BC NT YT NU
41%
% 45 32 50 45 NV 50 30 55 30 30 NV NV NV
NL NS PE NB QC ON MB SK AB BC NT YT NU
26%
% 10 28 20 35 NV 20 40 20 50 10 NV NV NV
NL NS PE NB QC ON MB SK AB BC NT YT NU
33%
% 45 40 30 20 NV 30 30 25 20 60 NV NV NV
- 99 -
APPENDIX E PIE CHART*
F A
11% 15%
E
15% B
14%
D
C
21%
24%
TITLES OF BLOCKS
- 100 -
APPENDIX F TASK PROFILE CHART
Industrial Mechanic (Millwright)
1. Performs 1.01 Uses personal 1.02 Maintains 1.03 Protects the 1.04 Performs
A COMMON safety-related protective safe work environment. lock-out/tag-out
OCCUPATIONAL functions. equipment (PPE) environment. and zero energy
SKILLS and safety procedures.
equipment.
2. Maintains and 2.01 Maintains 2.02 Maintains 2.03 Maintains 2.04 Maintains 2.05 Uses shop
uses tools and hand and portable precision rigging, welding machines.
equipment. power tools. measuring and hoisting/lifting equipment.
layout tools. and moving
equipment.
3. Performs 3.01 Plans work. 3.02 Fabricates 3.03 Lubricates 3.04 Performs 3.05 Uses
routine trade workpiece. systems and leveling of fastening and
tasks. components. components and retaining devices.
systems.
5. Performs 5.01 Cuts material 5.02 Joins material 5.03 Welds 5.04 Welds 5.05 Welds
cutting and with gas and using gas welding material using arc material with gas material with gas
welding plasma arc cutting equipment. welding metal arc welding tungsten arc
operations. equipment. equipment. (GMAW (MIG)) welding (GTAW
equipment. (TIG)) equipment.
- 101 -
BLOCKS TASKS SUB-TASKS
8. Services prime 8.01 Installs prime 8.02 Diagnoses 8.03 Repairs prime
C MECHANICAL movers. movers. prime movers. movers.
COMPONENTS
AND SYSTEMS
9. Services shafts, 9.01 Installs 9.02 Diagnoses 9.03 Repairs 9.04 Maintains
bearings and shafts, bearings shafts, bearings shafts, bearings shafts, bearings
seals. and seals. and seals. and seals. and seals.
11. Services chain 11.01 Installs 11.02 Diagnoses 11.03 Repairs 11.04 Maintains
and belt drive chain and belt chain and belt chain and belt chain and belt
systems. drive systems. drive systems. drive systems. drive systems.
12. Services gear 12.01 Installs gear 12.02 Diagnoses 12.03 Repairs gear 12.04 Maintains
systems. systems. gear systems. systems. gear systems.
- 102 -
BLOCKS TASKS SUB-TASKS
13. Services fans 13.01 Installs fans 13.02 Diagnoses 13.03 Repairs fans 13.04 Maintains
D MATERIAL and blowers. and blowers. fans and blowers. and blowers. fans and blowers.
HANDLING/
PROCESS SYSTEMS
14. Services 14.01 Installs 14.02 Diagnoses 14.03 Repairs 14.04 Maintains
compressors. compressors. compressors. compressors. compressors.
15. Services 15.01 Installs 15.02 Diagnoses 15.03 Repairs 15.04 Maintains
pumps. pumps. pumps. pumps. pumps.
16. Services 16.01 Installs 16.02 Diagnoses 16.03 Repairs 16.04 Maintains
conveying conveying conveying conveying conveying
systems. systems. systems. systems. systems.
17. Services 17.01 Installs 17.02 Diagnoses 17.03 Repairs 17.04 Maintains
process tanks and process tanks and process tanks and process tanks and process tanks and
containers. containers. containers. containers. containers.
18. Services 18.01 Installs 18.02 Diagnoses 18.03 Repairs 18.04 Maintains
E HYDRAULIC, hydraulic hydraulic hydraulic hydraulic hydraulic
PNEUMATIC AND systems. systems. systems. systems. systems.
VACUUM SYSTEMS
19. Services 19.01 Installs 19.02 Diagnoses 19.03 Repairs 19.04 Maintains
pneumatic and pneumatic and pneumatic and pneumatic and pneumatic and
vacuum systems. vacuum systems. vacuum systems. vacuum systems. vacuum systems.
- 103 -
BLOCKS TASKS SUB-TASKS
21. Performs 21.01 Performs 21.02 Performs 21.03 Performs 21.04 Performs 21.05 Performs
specialized vibration analysis balancing alignment non-destructive fluid analysis
testing and procedures. procedures. procedures. testing (NDT) procedures.
analysis. procedures.
- 104 -