Professional Documents
Culture Documents
Test Questions 2013 PDF
Test Questions 2013 PDF
The schematic below shows the process of water treatment in a production facility. Use the
schematic to answer questions 14 to 16
13. Fill in the name of the unnamed equipment in the schematic below
a
. b
Fig. 1
a) ________________________________
b) ________________________________
14. A centrifugal separator that will remove oil drops from the water is called __________________
15. The function of the last Equipment in the Water treatment is to
a) Remove the remaining water droplets from the oil
b) Remove the remaining oil droplets from the water
c) Pump lean glycol into the water for purification
d) Transfer the oil for final water removal
16. Removing salt from oil is the work of which equipment __________________
17. Removal of remaining fractions of water from gas in gas plant is the function of
a) Reboiler b) Scrubber c) Separator d) Compressor
18. The part of a subsea pipeline linking the platform to seabed is called
a) Pig b) Riser c) Skid d) Pipe
19. Maintenance of the Well without killing the Well is called
a) Well Workover b) Well Intervention c) Well Interception d) Primary Recover
20. The Scrubber is to the Gas treatment what the ____________is to the Water treatment
a) Heat Exchanger b) Scrubber c) Separator d) Hydro cyclone
21. Separation/stabilization and electrical multiphase pumping may be necessary for Subsea Wells if
December 16, 2013 [ARIOSH TRAINEE TEST.]
i. x>y
ii. x<y
iii. y= 1/16
iv. y= 1/4
a) Statement 1and 2 only b) Statements 2 and 4 only c) Statements 1 and 4 only
i. Pipe 1/8 to 12 has an outside diameter greater than its nominal pipe length
ii. Pipe 14 and above has an outside diameter equal to its nominal pipe size
December 16, 2013 [ARIOSH TRAINEE TEST.]
iii. The method of sizing pipe maintains a uniform outside diameter while varying the inside
diameter.
a) Statements 1 and 2 only b) Statements 1 and 3 only c) All of the above
28. What is the angular spacing between the bolt holes on the 2150# flange
30. Which of these valves prevents excessive pressure on a gas service line?
31. A valve often used to ensure a unidirectional flow of fluid along a pipe is called what?
a)Choke valve b)Pneumatic actuated gate valve c)Check valve d)Hydraulic actuated gate valve
32. What type of flange measures the rate of flow of fluid through the piping system?
33. The equipment designed primarily for the transfer of air, gases or liquids by way of re-pressurizing
them is called what?
38. Which of these pair of valves fully opens or fully closes by a 90 degrees turn of its wrench?
a) Ball valve and butterfly valve b) Globe valve and check valve
c) Ball valve and globe valve d) Gate valve and ball valve
39. The fitting x above connecting the two pipes A & B is what?
i. Screwed and socket weld fittings are normally reserved for installations using fittings 3 and
smaller
ii. Forged steel screwed and socket weld fittings are manufactured in 2 pressure classes-3000#
and 6000#
iii. Swages and plugs are manufactured with external threads
i. Screwed and socket weld fittings can be placed one fitting directly in contact with the other
ii. Screwed fittings are manufactured with threads on the inside of the fitting
iii. Pipe nipples are used to facilitate the assembly of screwed and socket weld fittings
42. Which of the following statements is/are true about Screwed swages?
December 16, 2013 [ARIOSH TRAINEE TEST.]
44. Which of the following pair can be used for making a branch connection?
a) Stub-in and Olet b) Olets and couplings c) Couplings and elbows d) Stub-in and
caps