Professional Documents
Culture Documents
Service Manual: DSC-S980
Service Manual: DSC-S980
SERVICE MANUAL
US Model
Ver. 1.0 2009.01 Canadian Model
Revision History AEP Model
UK Model
Internal memory
E Model
ON BOARD Australian Model
Korea Model
Photo: Silver
Link
SPECIFICATIONS DISASSEMBLY REPAIR PARTS LIST
In case of the CCD assy or main board failure, contact your local Sony
Service Headquarter for the measures.
2009A0500-1
DSC-S980 2009.1
9-852-650-11 Sony EMCS Co. Published by Kohda TEC
SPECIFICATIONS
DSC-S980
2
CAUTION
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
Dispose of used batteries according to the instructions.
SAFETY CHECK-OUT
1. Check the area of your repair for unsoldered or poorly-soldered Unleaded solder
connections. Check the entire board surface for solder splashes Boards requiring use of unleaded solder are printed with the lead-
and bridges. free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
2. Check the interboard wiring to ensure that no wires are
the lead free mark due to their particular size.)
"pinched" or contact high-wattage resistors.
3. Look for unauthorized replacement parts, particularly
: LEAD FREE MARK
transistors, that were installed during a previous repair. Point
Unleaded solder has the following characteristics.
them out to the customer and recommend their replacement. Unleaded solder melts at a temperature about 40C higher than
4. Look for parts which, through functioning, show obvious signs ordinary solder.
of deterioration. Point them out to the customer and Ordinary soldering irons can be used but the iron tip has to be
recommend their replacement. applied to the solder joint for a slightly longer time.
5. Check the B+ voltage to see it is at the values specified. Soldering irons using a temperature regulator should be set to
6. Flexible Circuit Board Repairing about 350C.
Keep the temperature of the soldering iron around 270C Caution: The printed pattern (copper foil) may peel away if the
during repairing. heated tip is applied for too long, so be careful!
Strong viscosity
Do not touch the soldering iron on the same conductor of the
Unleaded solder is more viscous (sticky, less prone to flow) than
circuit board (within 3 times). ordinary solder so use caution not to let solder bridges occur such
Be careful not to apply force on the conductor when soldering as on IC pins, etc.
or unsoldering. Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
DSC-S980
3
1. SERVICE NOTE
1-1. METHOD FOR COPYING OR ERASING THE DATA IN INTERNAL MEMORY
The data can be copied/erased by the operations on the Setup screen. (When erasing the data, execute formatting the internal memory.)
Note: When replacing the camera, erase the data in internal memory of the board before replacement.
Copies all images in the internal memory to Memory Stick Duo media.
1 Insert Memory Stick Duo media having sufficient free capacity.
2 Select [Copy] with v/V on the control button, then press z.
The message All data on internal memory will be copied appears.
3 Select [OK] with v, then press z.
Copying starts.
To cancel copying
Select [Cancel] in step 3, then press z.
Use a fully charged battery pack. If you attempt to copy image files using a battery pack with little
remaining charge, the battery pack may run out, causing copying to fail or possibly corrupting the data.
You cannot select images to copy.
The original images in the internal memory are retained even after copying. To delete the contents of the
internal memory, remove the Memory Stick Duo media after copying, then format the internal memory
([Format] in [Internal Memory Tool]).
A new folder is created on the Memory Stick Duo media and all the data will be copied to it. You cannot
choose a specific folder and copy images to it.
The (Print order) marks on the images are not copied.
Format
To cancel formatting
Select [Cancel] in step 2, then press z.
DSC-S980
1-1E
2. DISASSEMBLY
1
2
3
1
1 SCREW_TP_1.7_3.7_A0.4_D3_N 1 SCREW_TP_1.7_3.7_A0.4_D3_N
2 MIDDLE BELT (L) 2 CABINET (REAR) ASSY
3 SCREW_TP_1.7_3.7_A0.4_D3_N
4 MIDDLE BELT (R)
1 1
3
(To page 2-2)
3 4
2
5
1 LCD 1 SCREW_TP_1.4_3_A_0.2_D=2.5
2 SCREW_TP_1.4_3_A_0.2_D=2.5 2 JACK COVER ASSY
3 LCD BRACKET 3 SCREW TP 1.4 2.5
4 CABINET (FRONT) ASSY
5 BT LID
DSC-S980
2-1
2
1
3 1
2
4
3
2
HELP02
3
R:1 k/1 W
(Part code: 1-215-869-11)
1 SCREW_TP_1.4_3_A_0.2_D=2.5 HELP01
2 CCD PLATE SHEET 1
3 CCD ASSY
4 LOW PASS FILTER SET
DSC-S980
2-2E
HELP
Sheet attachment positions and procedures of processing the flexible boards/harnesses are shown.
HELP01
Be careful about the Lens Assy
HELP02
DSC-S980
HELP
3. BLOCK DIAGRAM
3-1. OVERALL BLOCK DIAGRAM
TP54 ICE_CLK
TP55 ICE_Break
H1
H2
DSC-S980
3-1E
4. REPAIR PARTS LIST
NOTE:
-XX, -X mean standardized parts, so they may have some differences from
the original one. When indicating parts by reference number,
Items marked * are not stocked since they are seldom required for routine please include the board name.
service. Some delay should be anticipated when ordering these items.
The mechanical parts with no reference number in the exploded views are not The components identified by mark 0 or
supplied. dotted line with mark 0 are critical for safety.
Replace only with part number specified.
Due to standardization, replacements in the parts list may be different from
the parts specified in the components used on the set. Les composants identifis par une marque
0 sont critiques pour la scurit.
Ne les remplacer que par une pice portant
le numro spcifi.
Abbreviation
AR : Argentine model
AUS : Australian model
BR : Brazilian model
CH : Chinese model
CND : Canadian model
EE : East European model
HK : Hong Kong model
J : Japanese model
JE : Tourist model
KR : Korea model
NE : North European model
TW : Taiwan model
TH : Thai model
DSC-S980
4-1
4-1. EXPLODED VIEWS
4-1-1. OVERALL SECTION
3
2
4 6
5 7
7
8
4
Ref. No. Part No. Description Ref. No. Part No. Description
1 X-2345-955-1 CABINET (FRONT) ASSY (S) (SILVER) 5 4-136-408-01 BELT (L), MIDDLE
1 X-2345-956-1 CABINET (FRONT) ASSY (B) (BLACK) 6 X-2345-941-1 COVER ASSY (S), JACK (SILVER)
1 X-2345-957-1 CABINET (FRONT) ASSY (P) (PINK)
2 X-2345-958-1 CABINET (UPPER) ASSY 6 X-2345-942-1 COVER ASSY (B), JACK (BLACK)
3 X-2345-944-1 CABINET (REAR) ASSY (S) (SILVER) 6 X-2345-943-1 COVER ASSY (P), JACK (PINK)
7 3-288-943-01 SCREW_TP_1.4_3_A_0.2_D=2.5
3 X-2345-945-1 CABINET (REAR) ASSY (B) (BLACK) 8 3-113-001-01 SCREW TP 1.4*2.5
3 X-2345-954-1 CABINET (REAR) ASSY (P) (PINK) 9 4-136-409-01 BELT (R), MIDDLE
4 4-137-870-01 SCREW_TP_1.7_3.7_A0.4_D3_N
DSC-S980
4-2
4-1-2. MAIN FRAME SECTION
55
(Note 2)
52
56
52
51
(Note 2)
53
ns
(Note 1, 2)
JC1
F2
F1
57
58
Lens Section
(See page 4-4)
53
54
Ref. No. Part No. Description Ref. No. Part No. Description
51 A-1701-267-A ST BLOCK ASSY (Note 2) 56 4-135-313-01 BRACKET, LCD
52 3-288-943-01 SCREW_TP_1.4_3_A_0.2_D=2.5 57 X-2345-712-1 MAIN FRAME SUB ASSY
53 4-137-871-01 SCREW_TP_1.4_3.5_A0.3_D2.5_N 58 4-135-315-01 SHEET, CCD CONNECTOR
54 4-135-316-01 LID (S), BT (SILVER)
54 4-135-317-01 LID (B), BT (BLACK) 0 F1 1-576-363-11 FUSE (1A/30V)
0 F2 1-576-913-11 FUSE, MICRO (1608 TYPE) (1.6A/36V)
54 4-135-318-01 LID (P), BT (PINK) * JC1 1-820-333-11 MULTI CONNECTOR (REC) 8P (USB A/V OUT)
55 4-135-314-01 LCD (Note 2)
DSC-S980
4-3
4-1-3. LENS SECTION
104
101 103
ns
ns ns
ns (CCD Assy)
102 (Note)
Note: In case of the CCD assy failure, contact your local Sony
service Headquarter for the measures.
Ref. No. Part No. Description Ref. No. Part No. Description
101 A-1701-284-A LENS BLOCK ASSY 103 4-135-323-01 CCD PLATE SHEET
102 4-135-324-01 FILTER SET, LOW PASS 104 3-288-943-01 SCREW_TP_1.4_3_A_0.2_D=2.5
DSC-S980
4-4
4-2. ACCESSORIES
Checking supplied accessories.
DSC-S980
4-5E
[Regarding Fuse]
MAIN BOARD
Ref. No.: F1
Part No.: 1-576-363-11
Description: FUSE, MICRO (1005 TYPE) (1A/30V)
Ref. No.: F2
Part No.: 1-576-913-11
Description: FUSE, MICRO (1608 TYPE) (1.6A/36V)
DSC-S980
Reverse 985265011.pdf
Revision History
S.M. Rev.
Ver. Date History Contents
issued
1.0 2009.01 Official Release
DSC-S980