Professional Documents
Culture Documents
Nammcesa 000044 PDF
Nammcesa 000044 PDF
Nammcesa 000044 PDF
C F M
56-5B
__________
HIGHLIGHTS
Pages which have been revised are outlined below, together with the Highlights of the
Revision
--------------------------------------------------------------------------------------
CH/SE/SU C REASON FOR CHANGE EFFECTIVITY
PAGES
--------------------------------------------------------------------------------------
CHAPTER 76
__________
76-HIGHLIGHTS Page 1 of 1
REVISION NO. 48 Feb 01/10
CES
C F M
56-5B
CHAPTER 76
__________
ENGINE CONTROLS
76-L.E.P. Page 1
Feb 01/10
CES
C F M
56-5B
CHAPTER 76
__________
ENGINE CONTROLS
TABLE OF CONTENTS
_________________
_______
SUBJECT ________
CH/SE/SU C
_ PAGE ___________
____ EFFECTIVITY
ENGINE CONTROLS - GENERAL
_________________________ 76-00-00
DESCRIPTION AND OPERATION 1 001-049, 051-099
101-149, 151-199
201-249, 251-299
301-399, 401-499
General 1 001-049, 051-099
101-149, 151-199
201-249, 251-299
301-399, 401-499
Throttle Control Lever 1 001-049, 051-099
101-149, 151-199
201-249, 251-299
301-399, 401-499
ENG/MASTER Control Switch 1 001-049, 051-099
101-149, 151-199
201-249, 251-299
301-399, 401-499
LP Fuel Shutoff Valve Control 1 001-049, 051-099
101-149, 151-199
201-249, 251-299
301-399, 401-499
Component Location 4 001-049, 051-099
101-149, 151-199
201-249, 251-299
301-399, 401-499
_____________
POWER CONTROL 76-10-00
DESCRIPTION AND OPERATION 1 001-049, 051-099
101-149, 151-199
201-249, 251-299
301-399, 401-499
General 1 001-049, 051-099
101-149, 151-199
201-249, 251-299
301-399, 401-499
Manual Thrust Setting Mode (the 1 001-049, 051-099
autothrust function is not 101-149, 151-199
active) 201-249, 251-299
301-399, 401-499
Automatic Thrust Setting Mode 1 001-049, 051-099
(the autothrust function is 101-149, 151-199
active) 201-249, 251-299
301-399, 401-499
76-CONTENTS Page 1
Nov 01/08
R
CES
C F M
56-5B
CHAPTER 76
__________
ENGINE CONTROLS
TABLE OF CONTENTS
_________________
SUBJECT
_______ CH/SE/SU
________ C
_ PAGE EFFECTIVITY
____ ___________
101-149, 151-199
201-249, 251-299
301-399, 401-499
General 1 001-049, 051-099
101-149, 151-199
201-249, 251-299
301-399, 401-499
Throttle Control Mechanical Parts 1 001-049, 051-099
101-149, 151-199
201-249, 251-299
301-399, 401-499
Throttle Control Lever 1 001-049, 051-099
101-149, 151-199
201-249, 251-299
301-399, 401-499
Throttle Control Artificial Feel 5 001-049, 051-099
Unit 101-149, 151-199
201-249, 251-299
301-399, 401-499
Throttle Control Unit 5 001-049, 051-099
101-149, 151-199
201-249, 251-299
301-399, 401-499
76-CONTENTS Page 2
Nov 01/08
R
CES
C F M
56-5B
CHAPTER 76
__________
ENGINE CONTROLS
TABLE OF CONTENTS
_________________
SUBJECT
_______ CH/SE/SU
________ C
_ PAGE EFFECTIVITY
____ ___________
201-249, 251-299
301-399, 401-499
Installation of the Throttle 408 001-049, 051-099
Control Feel Unit 101-149, 151-199
201-249, 251-299
301-399, 401-499
CONTROL UNIT - THROTTLE 76-11-19
REMOVAL/INSTALLATION 401 001-049, 051-099
101-149, 151-199
201-249, 251-299
301-399, 401-499
Removal of the Throttle Control 401 001-049, 051-099
Unit (8KS1, 8KS2) 101-149, 151-199
201-249, 251-299
301-399, 401-499
Installation of the Throttle 406 001-049, 051-099
Control Unit (8KS1, 8KS2) 101-149, 151-199
201-249, 251-299
301-399, 401-499
LEVER ASSEMBLY - THROTTLE CONTROL 76-11-41
REMOVAL/INSTALLATION 401 001-049, 051-099
101-149, 151-199
201-249, 251-299
301-399, 401-499
Removal of the Throttle Control 401 001-049, 051-099
Lever Assembly 101-149, 151-199
201-249, 251-299
301-399, 401-499
Installation of the Throttle 413 001-049, 051-099
Control Lever Assembly 101-149, 151-199
201-249, 251-299
301-399, 401-499
76-CONTENTS Page 3
Nov 01/08
R
CES
C F M
56-5B
CHAPTER 76
__________
ENGINE CONTROLS
TABLE OF CONTENTS
_________________
SUBJECT
_______ CH/SE/SU
________ C
_ ____ EFFECTIVITY
PAGE ___________
Valve Operation 1 001-049, 051-099
101-149, 151-199
201-249, 251-299
301-399, 401-499
LP Fuel Shut Off Valve Control 4 001-049, 051-099
101-149, 151-199
201-249, 251-299
301-399, 401-499
General 4 001-049, 051-099
101-149, 151-199
201-249, 251-299
301-399, 401-499
Valve Operation 4 001-049, 051-099
101-149, 151-199
201-249, 251-299
301-399, 401-499
76-CONTENTS Page 4
Nov 01/08
R
CES
C F M
56-5B
ENGINE CONTROLS - GENERAL - DESCRIPTION AND OPERATION
_____________________________________________________
1. _______
General
The engine control system consist of :
- the throttle control
- the HP fuel shutoff valve control
- the LP fuel control.
R
EFF : 001-049, 051-099, 101-149, 151-199,
201-249, 251-299, 301-399, 401-499,
76-00-00
Page 1
Nov 01/08
CES
C F M
56-5B
R
EFF : 001-049, 051-099, 101-149, 151-199,
201-249, 251-299, 301-399, 401-499,
76-00-00
Page 2
Nov 01/08
CES
C F M
56-5B
R
EFF : 001-049, 051-099, 101-149, 151-199,
201-249, 251-299, 301-399, 401-499,
76-00-00
Page 3
Nov 01/08
CES
C F M
56-5B
2. __________________
Component Location
(Ref. Fig. 003)
-------------------------------------------------------------------------------
FIN I FUNCTIONAL DESIGNATION I PANELIZONEIACCESS I ATA
I I I I DOOR I REF.
-------------------------------------------------------------------------------
2KC CTL SW-ENG/MASTER 2 115VU 210 76-12-00
3KC CTL SW-ENG/MASTER 1 115VU 210 76-12-00
4000KC SOLENOID-HP FUEL SOV 437 437AL 80-11-20
447 447AL
8KS1 CTL UNIT-THROTTLE, ENG1 11VU 210 76-11-17
8KS2 CTL UNIT-THROTTLE, ENG2 11VU 210 76-11-17
R
EFF : 001-049, 051-099, 101-149, 151-199,
201-249, 251-299, 301-399, 401-499,
76-00-00
Page 4
Nov 01/08
CES
C F M
56-5B
R
EFF : 001-049, 051-099, 101-149, 151-199,
201-249, 251-299, 301-399, 401-499,
76-00-00
Page 5
Nov 01/08
CES
C F M
56-5B
POWER CONTROL - DESCRIPTION AND OPERATION
_________________________________________
1. _______
General
(Ref. Fig. 001)
R
EFF : 001-049, 051-099, 101-149, 151-199,
201-249, 251-299, 301-399, 401-499,
76-10-00
Page 1
Nov 01/08
CES
C F M
56-5B
R
EFF : 001-049, 051-099, 101-149, 151-199,
201-249, 251-299, 301-399, 401-499,
76-10-00
Page 2
Nov 01/08
CES
C F M
56-5B
THROTTLE CONTROL - DESCRIPTION AND OPERATION
____________________________________________
1. _______
General
(Ref. Fig. 001)
The throttle control system consist of :
- the throttle control lever
- the throttle control artificial feel unit
- the throttle control unit
- the electrical harness.
In addition each throttle control lever is fitted with an instinctive
pushbutton switch.
This pushbutton switch serves for the de-activation and disengagement of the
autothrust function.
The design of the throttle control is based upon a fixed throttle concept :
this means that the throttle control levers are not servo motorized.
2. _________________________________
Throttle Control Mechanical Parts
R
EFF : 001-049, 051-099, 101-149, 151-199,
201-249, 251-299, 301-399, 401-499,
76-11-00
Page 1
Nov 01/08
CES
C F M
56-5B
R
EFF : 001-049, 051-099, 101-149, 151-199,
201-249, 251-299, 301-399, 401-499,
76-11-00
Page 2
Nov 01/08
CES
C F M
56-5B
R
EFF : 001-049, 051-099, 101-149, 151-199,
201-249, 251-299, 301-399, 401-499,
76-11-00
Page 3
Nov 01/08
CES
C F M
56-5B
R
EFF : 001-049, 051-099, 101-149, 151-199,
201-249, 251-299, 301-399, 401-499,
76-11-00
Page 4
Nov 01/08
CES
C F M
56-5B
In the forward range (35 deg. to 45 deg. TLA), the autothrust function
cannot be activated (except in alpha floor condition).
This range corresponds to the selection of FLEX TAKE OFF/MAX TAKE OFF (GO
AROUND) mode.
The throttle control lever is linked to a mechanical rod. This rod drives
the input lever of the throttle control artificial feel unit.
R
EFF : 001-049, 051-099, 101-149, 151-199,
201-249, 251-299, 301-399, 401-499,
76-11-00
Page 5
Nov 01/08
CES
C F M
56-5B
R
EFF : 001-049, 051-099, 101-149, 151-199,
201-249, 251-299, 301-399, 401-499,
76-11-00
Page 6
Nov 01/08
CES
C F M
56-5B
R
EFF : 001-049, 051-099, 101-149, 151-199,
201-249, 251-299, 301-399, 401-499,
76-11-00
Page 7
Nov 01/08
CES
C F M
56-5B
R
EFF : 001-049, 051-099, 101-149, 151-199,
201-249, 251-299, 301-399, 401-499,
76-11-00
Page 8
Nov 01/08
CES
C F M
56-5B
R
EFF : 001-049, 051-099, 101-149, 151-199,
201-249, 251-299, 301-399, 401-499,
76-11-00
Page 9/10
Nov 01/08
CES
C F M
56-5B
- a safety device which leads the resolvers outside the normal operating
range in case of failure of the driving device
- two output electrical connectors.
The input lever drives two gear sectors assembled face to face. Each
sector drives itself a set of one resolver and three potentiometers.
The relationship between the throttle lever angle and throttle resolver
angle (TRA) is linear and : 1 deg. TLA = 1.9 TRA.
The accuracy of the throttle control unit (error between the input lever
position and the resolver angle) is 0.5 deg. TRA.
The maximum discrepancy between the signals generated by the two
resolvers is 0.25 deg. TRA. The TLA resolver operates in two quadrants :
the first quadrant serves for positive angles and the fourth quadrant for
negative angles.
Each resolver is dedicated to one channel of the ECU and receives its
electrical excitation from the ECU.
The ECU considers a throttle resolver angle value :
- less than -47.5 deg. TRA or
- greater than 98.8 deg. TRA as resolver position signal failure.
The ECU incorporates a resolver fault accomodation logic. This logic
allows engine operation after a failure or a complete loss of the
throttle resolver position signal.
R
EFF : 001-049, 051-099, 101-149, 151-199,
201-249, 251-299, 301-399, 401-499,
76-11-00
Page 11
Nov 01/08
CES
C F M
56-5B
THROTTLE CONTROL - ADJUSTMENT/TEST
__________________________________
TASK 76-11-00-820-044
1. __________________
Reason for the Job
Self Explanatory
2. ______________________
Job Set-up Information
-------------------------------------------------------------------------------
REFERENCE QTY DESIGNATION
-------------------------------------------------------------------------------
B. Consumable Materials
-------------------------------------------------------------------------------
REFERENCE DESIGNATION
-------------------------------------------------------------------------------
C. Referenced Information
-------------------------------------------------------------------------------
REFERENCE DESIGNATION
-------------------------------------------------------------------------------
R
EFF : 001-049, 051-099, 101-149, 151-199,
201-249, 251-299, 301-399, 401-499,
76-11-00
Page 501
Nov 01/08
CES
C F M
56-5B
-------------------------------------------------------------------------------
REFERENCE DESIGNATION
-------------------------------------------------------------------------------
3. __________
Job Set-up
Subtask 76-11-00-865-059
-------------------------------------------------------------------------------
PANEL DESIGNATION IDENT. LOCATION
-------------------------------------------------------------------------------
49VU ENGINE/1 AND 2/IGN/SYS A 1JH A03
49VU FLIGHT CONTROLS/SEC1/NORM/SPLY 21CE1 B08
49VU LIGHTING/EMER LT/CKPT/DOME 1LE H08
105VU FLT CTL/SEC1/STBY SPLY 22CE B01
121VU ENGINE/IGN/ENG2/SYS B 3JH2 P42
121VU ENGINE/IGN/ENG1/SYS B 3JH1 P41
121VU ENGINE/IGN/ENG2/SYS A BAT 2JH2 P40
121VU ENGINE/IGN/ENG1/SYS A BAT 2JH1 P39
121VU FLIGHT CONTROLS/SEC3/SPLY 21CE3 Q19
121VU FLIGHT CONTROLS/SEC2/SPLY 21CE2 Q18
122VU LIGHTING/INSTL LT/MAIN INST/PNL AND/PED 4LF Y04
122VU LIGHTING/FLOOD/CTR INST/PNL 2LE Z04
Subtask 76-11-00-941-056
B. Safety Precautions
(a) Put a warning notice to tell persons not to start the engine.
(2) Make sure that the engine 1(2) shutdown occurred not less than 5
minutes before you do this procedure.
R
EFF : 001-049, 051-099, 101-149, 151-199,
201-249, 251-299, 301-399, 401-499,
76-11-00
Page 502
Nov 01/08
CES
C F M
56-5B
(3) On the overhead maintenance panel 50VU:
(a) Make sure that the ON legend of the ENG/FADEC GND PWR/1(2)
pushbutton switch is off.
(b) Put a warning notice to tell persons not to energize the FADEC
1(2).
Subtask 76-11-00-010-055
4. Procedure
_________
Subtask 76-11-00-869-060
A. Put the throttle control lever in the IDLE STOP position and hold it in
this position
(Ref. Fig. 501/TASK 76-11-00-991-910)
detail A.
CAUTION : DO NOT APPLY FORCE TO PUSH IN OR PUSH OUT THE RIGGING PINS
_______
IN THE RIGGING HOLES. IF THE RIGGING PINS ARE DIFFICULT TO
PUSH IN, YOU MUST ADJUST THE RODS UNTIL THEY GO IN EASILY.
(a) Make sure that you can easily install and remove the RIGGING PIN
(98DNSA20208080) (5) in the artificial feel unit (1).
(b) If you can not do this, adjust the length of the rod (6).
Subtask 76-11-00-820-058
(1) Remove the Multipurpose Control and Display Units 3CA1 and 3CA2
(Ref. TASK 22-82-12-000-001)
(2) Remove the Radio Management Panels 1RG1 and 1RG2 (Ref. TASK 23-13-13-
000-001)
(3) Remove the Audio Control Panels 2RN1 and 2RN2 (Ref. TASK 23-51-12-
000-001)
(4) Remove the Weather Radar Control Unit 3SQ (Ref. TASK 34-41-12-000-
001)
R
EFF : 001-049, 051-099, 101-149, 151-199,
201-249, 251-299, 301-399, 401-499,
76-11-00
Page 503
Nov 01/08
CES
C F M
56-5B
R
EFF : 001-049, 051-099, 101-149, 151-199,
201-249, 251-299, 301-399, 401-499,
76-11-00
Page 504
Nov 01/08
CES
C F M
56-5B
(5) Remove the ATC/TCAS Control Unit 3SH (Ref. TASK 34-52-12-000-001)
(6) Remove the FLOOD LT/INTEG LT panel 111VU and FLOOD LT panel 112VU.
(Ref. Fig. 502/TASK 76-11-00-991-911)
NOTE : The removal procedure is the same for the FLOOD LT/INTEG LT
____
panel 111VU and FLOOD LT panel 112VU.
(a) Release the fasteners of the panel (1) and disengage the panel
(1) from its housing.
(12) Cut and remove the lockwire and adjust the length of the adjustable
rod (6)
(Ref. Fig. 501/TASK 76-11-00-991-910)
detail B.
(13) Tighten and safety the hinge points and the adjustable rod ends with
lockwire 0.032 in. (0.8 mm) dia..
Subtask 76-11-00-869-061
C. With the throttle control lever in the IDLE STOP position, make sure that
you can :
(1) Easily install the pin (5) in the artificial feel unit (1)
(2) Easily remove this pin from the artificial feel unit (1)
R
EFF : 001-049, 051-099, 101-149, 151-199,
201-249, 251-299, 301-399, 401-499,
76-11-00
Page 505
Nov 01/08
CES
C F M
56-5B
R
EFF : 001-049, 051-099, 101-149, 151-199,
201-249, 251-299, 301-399, 401-499,
76-11-00
Page 506
Nov 01/08
CES
C F M
56-5B
R
EFF : 001-049, 051-099, 101-149, 151-199,
201-249, 251-299, 301-399, 401-499,
76-11-00
Page 507
Nov 01/08
CES
C F M
56-5B
(4) Make sure that you can:
(c) If you can not do this, adjust the length of the rod (2).
Subtask 76-11-00-820-057
D. Cut and remove the lockwire and adjust the length of the adjustable rod
(2).
(Ref. Fig. 501/TASK 76-11-00-991-910)
detail B.
(1) Disconnect the rod (2) from the throttle control unit and the
artificial feel unit to install the lockwire 0.032 in. (0.8mm) dia..
Tighten and safety the hinge points and the adjustable rod ends.
Subtask 76-11-00-869-062
E. Remove the pin (5). With the throttle control lever in the IDLE STOP
position make sure that you can :
(1) Easily remove the pin (3) from the throttle control unit.
(2) Easily install this pin in this unit. Remove this pin.
5. Close-up
________
Subtask 76-11-00-869-063
R
EFF : 001-049, 051-099, 101-149, 151-199,
201-249, 251-299, 301-399, 401-499,
76-11-00
Page 508
Nov 01/08
CES
C F M
56-5B
(6) Install the FLOOD LT/INTEG LT panel 111VU and FLOOD LT panel 112VU.
(Ref. Fig. 502/TASK 76-11-00-991-911)
NOTE : The installation procedure is the same for the FLOOD LT/INTEG
____
LT panel 111VU and FLOOD LT panel 112VU.
(a) Remove the blanking caps from the connectors (2) and (3).
(7) Install the Multipurpose Control and Display Units (3CA1 and 3CA2).
(Ref. TASK 22-82-12-400-002)
(8) Install the Radio Management Panels (1RG1 and 1RG2) (Ref. TASK 23-13-
13-400-001)
(9) Install the Audio Control Panels (2RN1 and 2RN2) (Ref. TASK 23-51-12-
400-001)
(10) Install the Weather Radar Control Unit (3SQ) (Ref. TASK 34-41-12-400-
001)
(11) Install the ATC/TCAS Control Unit (3SH) (Ref. TASK 34-52-12-400-001)
(12) Make sure that the work area is clean and clear of tool(s) and other
items.
Subtask 76-11-00-410-055
B. Close Access
Subtask 76-11-00-865-060
C. Remove the safety clip(s) and the tag(s) and close this(these) circuit
breaker(s):
1JH, 2JH1, 2JH2, 3JH1, 3JH2, 21CE1, 21CE2, 22CE, 21CE3.
R
EFF : 001-049, 051-099, 101-149, 151-199,
201-249, 251-299, 301-399, 401-499,
76-11-00
Page 509
Nov 01/08
CES
C F M
56-5B
Subtask 76-11-00-869-064
D. With the throttle control lever in the IDLE STOP position, make sure that
you can:
(1) easily install the pin (5) in the artificial feel unit (1)
(2) easily remove this pin from the artificial feel unit (1)
(5) easily install the RIGGING PIN (98DNSA20206080) (3) in the throttle
control unit (4) and in the input lever,
(a) If you can not do this, adjust the length of the rod (2).
Subtask 76-11-00-710-053
(1) Operate the light adjustment knobs of the FLOOD LT/INTEG LT panel
11VU and FLOOD LT panel 112VU.
(2) Make sure that the light intensity of the glareshield 13VU, F/O
glareshield panel 130VU, CAPT glareshield panel 131VU and overheard
control & indicating panel 48VU changes.
R
EFF : 001-049, 051-099, 101-149, 151-199,
201-249, 251-299, 301-399, 401-499,
76-11-00
Page 510
Nov 01/08
CES
C F M
56-5B
TASK 76-11-00-820-045
1. __________________
Reason for the Job
Self Explanatory
2. ______________________
Job Set-up Information
-------------------------------------------------------------------------------
REFERENCE QTY DESIGNATION
-------------------------------------------------------------------------------
B. Consumable Materials
-------------------------------------------------------------------------------
REFERENCE DESIGNATION
-------------------------------------------------------------------------------
C. Referenced Information
-------------------------------------------------------------------------------
REFERENCE DESIGNATION
-------------------------------------------------------------------------------
R
EFF : 001-049, 051-099, 101-149, 151-199,
201-249, 251-299, 301-399, 401-499,
76-11-00
Page 511
Nov 01/08
CES
C F M
56-5B
3. __________
Job Set-up
Subtask 76-11-00-865-061
-------------------------------------------------------------------------------
PANEL DESIGNATION IDENT. LOCATION
-------------------------------------------------------------------------------
49VU ENGINE/1 AND 2/IGN/SYS A 1JH A03
49VU FLIGHT CONTROLS/SEC1/NORM/SPLY 21CE1 B08
105VU FLT CTL/SEC1/STBY SPLY 22CE B01
121VU ENGINE/IGN/ENG2/SYS B 3JH2 P42
121VU ENGINE/IGN/ENG1/SYS B 3JH1 P41
121VU ENGINE/IGN/ENG2/SYS A BAT 2JH2 P40
121VU ENGINE/IGN/ENG1/SYS A BAT 2JH1 P39
121VU FLIGHT CONTROLS/SEC3/SPLY 21CE3 Q19
121VU FLIGHT CONTROLS/SEC2/SPLY 21CE2 Q18
Subtask 76-11-00-941-057
B. Safety Precautions
(a) Put a warning notice to tell persons not to start the engine.
(2) Make sure that the engine 1(2) shutdown occurred not less than 5
minutes before you do this procedure.
(a) Make sure that the ON legend of the ENG/FADEC GND PWR/1(2)
pushbutton switch is off.
(b) Put a warning notice to tell persons not to energize the FADEC
1(2).
Subtask 76-11-00-480-052
Subtask 76-11-00-941-058
R
EFF : 001-049, 051-099, 101-149, 151-199,
201-249, 251-299, 301-399, 401-499,
76-11-00
Page 512
Nov 01/08
CES
C F M
56-5B
Subtask 76-11-00-010-056
4. Procedure
_________
Subtask 76-11-00-020-052
(1) Cut and remove the lockwire from the lock nut (6). Loosen the lock
nut.
Subtask 76-11-00-820-059
B. Hold the adjusting rod (5) then turn the nut (4) to get a load of 0.8
+0.1 -0 daN (1.8 +0.22 -0.0000 lbf) on the related throttle control
lever.
NOTE : Measure this value in the IDLE STOP/MAX CLIMB range. Do not
____
measure this value at the detent points where the load increases
suddenly.
(1) Tighten the lock nut (6) to block the adjustment system. Measure the
load again to make sure that it is the same.
Subtask 76-11-00-420-052
C. Safety the lock nut (6) with lockwire 0.032 in. (0.8mm) dia..
Subtask 76-11-00-020-053
D. Cut and remove the lockwire from the lock nut (2). Loosen the lock nut.
Subtask 76-11-00-820-060
E. Turn the adjustment screw (1) to get a load equal to 2.5 +0.1 -0 daN
(5.62 +0.22 -0 lbf) when you go through the MAX CLIMB detent point (the
first detent point that you feel when you move the lever forward).
(1) Block the adjustment system. Measure the load again to make sure that
it is the same as the value given in the paragraph E.
R
EFF : 001-049, 051-099, 101-149, 151-199,
201-249, 251-299, 301-399, 401-499,
76-11-00
Page 513
Nov 01/08
CES
C F M
56-5B
R
EFF : 001-049, 051-099, 101-149, 151-199,
201-249, 251-299, 301-399, 401-499,
76-11-00
Page 514
Nov 01/08
CES
C F M
56-5B
Subtask 76-11-00-420-053
F. Safety the lock nut (2) with lockwire 0.032 in. (0.8mm) dia.
(1) Install the guard (7). Tighten the three screws (3).
5. Close-up
________
Subtask 76-11-00-410-056
A. Close Access
(1) Make sure that the work area is clean and clear of tool(s) and other
items.
Subtask 76-11-00-865-062
B. Remove the safety clip(s) and the tag(s) and close this(these) circuit
breaker(s):
1JH, 2JH1, 2JH2, 3JH1, 3JH2, 21CE1, 21CE2, 21CE3, 22CE
Subtask 76-11-00-080-052
R
EFF : 001-049, 051-099, 101-149, 151-199,
201-249, 251-299, 301-399, 401-499,
76-11-00
Page 515
Nov 01/08
CES
C F M
56-5B
ARTIFICIAL FEEL UNIT - THROTTLE CONTROL - REMOVAL/INSTALLATION
______________________________________________________________
TASK 76-11-17-000-042
1. __________________
Reason for the Job
Self Explanatory
2. ______________________
Job Set-up Information
-------------------------------------------------------------------------------
REFERENCE QTY DESIGNATION
-------------------------------------------------------------------------------
B. Referenced Information
-------------------------------------------------------------------------------
REFERENCE DESIGNATION
-------------------------------------------------------------------------------
R
EFF : 001-049, 051-099, 101-149, 151-199,
201-249, 251-299, 301-399, 401-499,
76-11-17
Page 401
Nov 01/08
CES
C F M
56-5B
3. __________
Job Set-up
Subtask 76-11-17-865-056
-------------------------------------------------------------------------------
PANEL DESIGNATION IDENT. LOCATION
-------------------------------------------------------------------------------
49VU ENGINE/1 AND 2/IGN/SYS A 1JH A03
49VU FLIGHT CONTROLS/SEC1/NORM/SPLY 21CE1 B08
49VU LIGHTING/EMER LT/CKPT/DOME 1LE H08
105VU FLT CTL/SEC1/STBY SPLY 22CE B01
121VU ENGINE/IGN/ENG2/SYS B 3JH2 P42
121VU ENGINE/IGN/ENG1/SYS B 3JH1 P41
121VU ENGINE/IGN/ENG2/SYS A BAT 2JH2 P40
121VU ENGINE/IGN/ENG1/SYS A BAT 2JH1 P39
121VU FLIGHT CONTROLS/SEC3/SPLY 21CE3 Q19
121VU FLIGHT CONTROLS/SEC2/SPLY 21CE2 Q18
122VU LIGHTING/INSTL LT/MAIN INST/PNL AND/PED 4LF Y04
122VU LIGHTING/FLOOD/CTR INST/PNL 2LE Z04
Subtask 76-11-17-869-052
B. Make sure that the throttle control levers are at idle (0 degree).
Subtask 76-11-17-941-053
C. Safety Precautions
(1) Put a warning notice in the cockpit to tell persons not to move:
- the throttle control levers
- the slat and flap control levers.
R
EFF : 001-049, 051-099, 101-149, 151-199,
201-249, 251-299, 301-399, 401-499,
76-11-17
Page 402
Nov 01/08
CES
C F M
56-5B
Subtask 76-11-17-010-052
D. Get Access
Subtask 76-11-17-010-055
E. Get Access
(1) Remove the Multipurpose Control and Display Units 3CA1 and 3CA2
(Ref. TASK 22-82-12-000-001).
(2) Remove the Radio Management Panels 1RG1 and 1RG2 (Ref. TASK 23-13-13-
000-001).
(3) Remove the Audio Control Panels 2RN1 and 2RN2 (Ref. TASK 23-51-12-
000-001).
(4) Remove the Weather Radar Control Unit 3SQ (Ref. TASK 34-41-12-000-
001).
(5) Remove the ATC Control Unit 3SH (Ref. TASK 34-52-12-000-001).
(6) Remove the FLOOD LT/INTEG LT panel 111VU and FLOOD LT panel 112VU.
(Ref. Fig. 401/TASK 76-11-17-991-908)
NOTE : The removal procedure is the same for the FLOOD LT/INTEG LT
____
panel 111VU and FLOOD LT panel 112VU.
(a) Release the fasteners of the panel (1) and disengage the panel
(1) from its housing.
R
EFF : 001-049, 051-099, 101-149, 151-199,
201-249, 251-299, 301-399, 401-499,
76-11-17
Page 403
Nov 01/08
CES
C F M
56-5B
R
EFF : 001-049, 051-099, 101-149, 151-199,
201-249, 251-299, 301-399, 401-499,
76-11-17
Page 404
Nov 01/08
CES
C F M
56-5B
(10) Remove the screws (6) and the washers (5).
(Ref. Fig. 402/TASK 76-11-17-991-909)
4. Procedure
_________
Subtask 76-11-17-480-052
Subtask 76-11-17-020-051
(2) Remove the 4 nuts (14), the 4 washers (15) and the 4 bolts (17). Make
sure that the 4 bushes (16) stay bonded.
(5) Remove the 2 nuts (19), the 2 washers (20) and the 2 bolts (26). Make
sure that the 2 bushes (25) stay bonded.
(6) Remove the 2 nuts (21), the 2 washers (22) and the 2 bolts (24).
R
EFF : 001-049, 051-099, 101-149, 151-199,
201-249, 251-299, 301-399, 401-499,
76-11-17
Page 405
Nov 01/08
CES
C F M
56-5B
R
EFF : 001-049, 051-099, 101-149, 151-199,
201-249, 251-299, 301-399, 401-499,
76-11-17
Page 406
Nov 01/08
CES
C F M
56-5B
R
EFF : 001-049, 051-099, 101-149, 151-199,
201-249, 251-299, 301-399, 401-499,
76-11-17
Page 407
Nov 01/08
CES
C F M
56-5B
TASK 76-11-17-400-042
1. __________________
Reason for the Job
Self Explanatory
2. ______________________
Job Set-up Information
-------------------------------------------------------------------------------
REFERENCE QTY DESIGNATION
-------------------------------------------------------------------------------
B. Consumable Materials
-------------------------------------------------------------------------------
REFERENCE DESIGNATION
-------------------------------------------------------------------------------
C. Expendable Parts
-------------------------------------------------------------------------------
FIG.ITEM |DESIGNATION |IPC-CSN
-------------------------------------------------------------------------------
R
EFF : 001-049, 051-099, 101-149, 151-199,
201-249, 251-299, 301-399, 401-499,
76-11-17
Page 408
Nov 01/08
CES
C F M
56-5B
D. Referenced Information
-------------------------------------------------------------------------------
REFERENCE DESIGNATION
-------------------------------------------------------------------------------
3. __________
Job Set-up
Subtask 76-11-17-860-051
(1) In the cockpit, make sure that the warning notice is in position to
tell persons not to move:
- the trottle control levers
- the slat and flap control levers
(2) On the center pedestal, on the ENG panel 115VU, make sure that a
warning notice is in position to tell persons not to start the
engine.
(3) On the overhead maintenance panel 50VU, make sure that the ON legend
of the ENG/FADEC GND PWR/1(2) pushbutton switch is off. Make sure
that a warning notice is in position to tell persons not to energize
the FADEC 1(2).
R
EFF : 001-049, 051-099, 101-149, 151-199,
201-249, 251-299, 301-399, 401-499,
76-11-17
Page 409
Nov 01/08
CES
C F M
56-5B
(4) Make sure that the access platform is in position.
(5) Make sure that the MCDU 3CA1 and 3CA2 are removed (Ref. TASK 22-82-
12-000-001).
(6) Make sure that the Radio Management Panels 1RG1 and 1RG2 are removed
(Ref. TASK 23-13-13-000-001).
(7) Make sure that the Audio Control Panels 2RN1 and 2RN2 are removed
(Ref. TASK 23-51-12-000-001).
(8) Make sure that the Weather Radar Control Unit 3SQ is removed
(Ref. TASK 34-41-12-000-001).
(9) Make sure that the ATC Control Unit 3SH is removed (Ref. TASK 34-52-
12-000-001).
(10) Make sure that the FLOOD LT/INTEG LT panel 111VU and FLOOD LT panel
112VU are removed.
Subtask 76-11-17-010-056
Subtask 76-11-17-865-057
C. Make sure that this(these) circuit breaker(s) is(are) open, safetied and
tagged
-------------------------------------------------------------------------------
PANEL DESIGNATION IDENT. LOCATION
-------------------------------------------------------------------------------
49VU ENGINE/1 AND 2/IGN/SYS A 1JH A03
49VU FLIGHT CONTROLS/SEC1/NORM/SPLY 21CE1 B08
49VU LIGHTING/EMER LT/CKPT/DOME 1LE H08
105VU FLT CTL/SEC1/STBY SPLY 22CE B01
121VU ENGINE/IGN/ENG2/SYS B 3JH2 P42
121VU ENGINE/IGN/ENG1/SYS B 3JH1 P41
121VU ENGINE/IGN/ENG2/SYS A BAT 2JH2 P40
121VU ENGINE/IGN/ENG1/SYS A BAT 2JH1 P39
121VU FLIGHT CONTROLS/SEC3/SPLY 21CE3 Q19
121VU FLIGHT CONTROLS/SEC2/SPLY 21CE2 Q18
122VU LIGHTING/INSTL LT/MAIN INST/PNL AND/PED 4LF Y04
122VU LIGHTING/FLOOD/CTR INST/PNL 2LE Z04
R
EFF : 001-049, 051-099, 101-149, 151-199,
201-249, 251-299, 301-399, 401-499,
76-11-17
Page 410
Nov 01/08
CES
C F M
56-5B
4. Procedure
_________
Subtask 76-11-17-420-051
(2) Install the 2 bolts (24), 2 washers (22) and 2 nuts (21).
(3) If necessary bond the bushes (25) on the bolts (26) with loctite 675
(Material No. CP2188).
(4) Install the 2 bolt assemblies (26), the 2 washers (20) and the 2 nuts
(19).
(8) If necessary bond the 4 bushes (16) on the 4 bolts (17) with loctite
675 (Material No. CP2188).
(9) Install the 4 bolt assemblies (17), the 4 washers (15) and the 4 nuts
(14).
Subtask 76-11-17-820-052
(1) Make sure that you can easily install and remove the rigging pin
RIGGING PIN (98DNSA20208080) (12) in the artificial feel unit (23).
(Ref. Fig. 403/TASK 76-11-17-991-910)
(a) If you can not do this, adjust the length of the rod (Ref. TASK
76-11-00-820-044).
R
EFF : 001-049, 051-099, 101-149, 151-199,
201-249, 251-299, 301-399, 401-499,
76-11-17
Page 411
Nov 01/08
CES
C F M
56-5B
R
EFF : 001-049, 051-099, 101-149, 151-199,
201-249, 251-299, 301-399, 401-499,
76-11-17
Page 412
Nov 01/08
CES
C F M
56-5B
(2) Make sure that you can easily install and remove the rigging pin
RIGGING PIN (98DNSA20206080) (11) in the throttle control unit.
(Ref. Fig. 403/TASK 76-11-17-991-910)
(a) If you cannot do this, adjust the length of the rod (Ref. TASK
76-11-00-820-044).
Subtask 76-11-17-420-054
Subtask 76-11-17-080-052
D. Remove the rigging pin (12) from the artificial feel unit and the rigging
pin (11) from the throttle control unit.
Subtask 76-11-17-480-053
Subtask 76-11-17-820-053
(1) Measure the value necessary to move the throttle control lever
between the IDLE STOP and the MAX CLIMB.
(a) This value must be 0.8 +0.1 -0 daN (1.8 +0.2 -0 lbf).
NOTE : Measure this value in the IDLE STOP to MAX CLIMB range. Do
____
not measure this value at the hard point where the load
increases suddenly.
(2) Measure the value necessary to move to more than MAX CLIMB hard
point.
(a) This value must be 2.5 +0.1 -0 daN (5.62 +0.22 -0 lbf).
(3) If you do not get these values, adjust the artificial feel unit
(Ref. TASK 76-11-00-820-045)
Subtask 76-11-17-080-053
R
EFF : 001-049, 051-099, 101-149, 151-199,
201-249, 251-299, 301-399, 401-499,
76-11-17
Page 413
Nov 01/08
CES
C F M
56-5B
5. Close-up
________
Subtask 76-11-17-410-052
A. Close Access
(1) Make sure that the work area is clean and clear of tool(s) and other
items.
(7) Install the FLOOD LT/INTEG LT panel 111VU and FLOOD LT panel 112VU.
(Ref. Fig. 401/TASK 76-11-17-991-908)
NOTE : The installation procedure is the same for the FLOOD LT/INTEG
____
LT panel 111VU and FLOOD LT panel 112VU.
(a) Remove the blanking caps from the connectors (2) and (3).
(8) Install the Multipurpose Control and Display Units (3CA1 and 3CA2).
(Ref. TASK 22-82-12-400-002).
(9) Install the Radio Management Panels (1RG1 and 1RG2) (Ref. TASK 23-13-
13-400-001).
(10) Install the Audio Control Panels (2RN1 and 2RN2) (Ref. TASK 23-51-12-
400-001).
(11) Install the Weather Radar Control Unit (3SQ) (Ref. TASK 34-41-12-400-
001).
(12) Install the ATC Control Unit (3SH) (Ref. TASK 34-52-12-400-001)
R
EFF : 001-049, 051-099, 101-149, 151-199,
201-249, 251-299, 301-399, 401-499,
76-11-17
Page 414
Nov 01/08
CES
C F M
56-5B
Subtask 76-11-17-410-053
B. Close Access
Subtask 76-11-17-865-058
C. Remove the safety clip(s) and the tag(s) and close this(these) circuit
breaker(s):
1JH, 2JH1, 2JH2, 3JH1, 3JH2, 21CE1, 21CE2, 21CE3, 22CE, 1LE, 2LE, 4LF.
Subtask 76-11-17-710-052
(1) operate the light adjustment knobs of the panels FLOOD LT/INTEG LT
PNL 111VU and FLOOD LT PNL 112VU.
(2) Make sure that the light intensity of the glareshield panels 13VU,
F/O glareshield panel 130VU, captain glareshield panel 131VU, and
overhead CTL & IND panel 48VU changes.
R
EFF : 001-049, 051-099, 101-149, 151-199,
201-249, 251-299, 301-399, 401-499,
76-11-17
Page 415
Nov 01/08
CES
C F M
56-5B
CONTROL UNIT - THROTTLE (8KS1,8KS2) - REMOVAL/INSTALLATION
__________________________________________________________
TASK 76-11-19-000-042
1. __________________
Reason for the Job
Self Explanatory
2. ______________________
Job Set-up Information
-------------------------------------------------------------------------------
REFERENCE QTY DESIGNATION
-------------------------------------------------------------------------------
B. Referenced Information
-------------------------------------------------------------------------------
REFERENCE DESIGNATION
-------------------------------------------------------------------------------
3. __________
Job Set-up
Subtask 76-11-19-865-057
-------------------------------------------------------------------------------
PANEL DESIGNATION IDENT. LOCATION
-------------------------------------------------------------------------------
FOR 8KS1
49VU ENGINE/1/FADEC A/AND EIU 1 2KS1 A04
121VU ENGINE/ENG1/FADEC B/AND EIU 1 4KS1 R41
FOR 8KS2
49VU ENGINE/2/FADEC A/AND EIU 2 2KS2 A05
121VU ENGINE/ENG2/FADEC B 4KS2 Q40
R
EFF : 001-049, 051-099, 101-149, 151-199,
201-249, 251-299, 301-399, 401-499,
76-11-19
Page 401
Nov 01/08
CES
C F M
56-5B
Subtask 76-11-19-010-051
B. Get Access
Subtask 76-11-19-869-056
C. Make sure that the throttle control levers are set to idle (0 degree
TLA).
4. Procedure
_________
Subtask 76-11-19-020-055
A. Disconnect Connectors
Subtask 76-11-19-480-052
B. Install the RIGGING PIN (98DNSA20208080) (13) in the artificial feel unit
of the throttle control.
Subtask 76-11-19-020-051
(2) Remove the nut (6), the washer (7) and the bolt (2). Make sure that
the bush (3) stays bonded to the bolt (2).
(4) Remove the three nuts (9), washers (10) and bolts (1) which attach
the throttle control unit (11) to its support.
EFF : 001-049, 051-099, 101-149, 151-199,
201-249, 251-299, 301-399, 401-499,
76-11-19
Page 402
Feb 01/10
CES
C F M
56-5B
R
EFF : 001-049, 051-099, 101-149, 151-199,
201-249, 251-299, 301-399, 401-499,
76-11-19
Page 403
Nov 01/08
CES
C F M
56-5B
EFF : 001-049, 051-099, 101-149, 151-199,
201-249, 251-299, 301-399, 401-499,
76-11-19
Page 404
Nov 01/09
CES
C F M
56-5B
R
EFF : 001-049, 051-099, 101-149, 151-199,
201-249, 251-299, 301-399, 401-499,
76-11-19
Page 405
Nov 01/08
CES
C F M
56-5B
TASK 76-11-19-400-042
1. __________________
Reason for the Job
Self Explanatory
2. ______________________
Job Set-up Information
-------------------------------------------------------------------------------
REFERENCE QTY DESIGNATION
-------------------------------------------------------------------------------
B. Consumable Materials
-------------------------------------------------------------------------------
REFERENCE DESIGNATION
-------------------------------------------------------------------------------
C. Expendable Parts
-------------------------------------------------------------------------------
FIG.ITEM |DESIGNATION |IPC-CSN
-------------------------------------------------------------------------------
R
EFF : 001-049, 051-099, 101-149, 151-199,
201-249, 251-299, 301-399, 401-499,
76-11-19
Page 406
Nov 01/08
CES
C F M
56-5B
D. Referenced Information
-------------------------------------------------------------------------------
REFERENCE DESIGNATION
-------------------------------------------------------------------------------
3. __________
Job Set-up
Subtask 76-11-19-860-052
(2) Make sure that the throttle control levers are set to idle (0 degree
TLA).
R (3) On the overhead maintenance panel 50VU, make sure that the ON legend
R of the ENG/FADEC GND PWR/1(2) pushbutton switch is off. Make sure
R that a warning notice is in position to tell persons not to energize
R the FADEC 1(2).
EFF : 001-049, 051-099, 101-149, 151-199,
201-249, 251-299, 301-399, 401-499,
76-11-19
Page 407
Feb 01/10
CES
C F M
56-5B
Subtask 76-11-19-010-054
Subtask 76-11-19-865-058
C. Make sure that this(these) circuit breaker(s) is(are) open, safetied and
tagged
-------------------------------------------------------------------------------
PANEL DESIGNATION IDENT. LOCATION
-------------------------------------------------------------------------------
49VU FLIGHT CONTROLS/SEC1/NORM/SPLY 21CE1 B08
105VU FLT CTL/SEC1/STBY SPLY 22CE B01
121VU FLIGHT CONTROLS/SEC3/SPLY 21CE3 Q19
121VU FLIGHT CONTROLS/SEC2/SPLY 21CE2 Q18
Subtask 76-11-19-869-057
(1) Make sure that the bush (3) is correctly bonded to the bolt (2).
(2) If necessary, bond the bush (3) to the bolt (2) with Loctite 675
(Material No. CP2188)
4. Procedure
_________
Subtask 76-11-19-420-051
(2) Install the throttle control unit 8KS1 (8KS2) (11) on its support.
(3) Install the three bolts (1) with the washers (10) and the nuts (9).
Tighten the bolts (1).
(5) Engage the rod (4) in the fork of the throttle control unit (11).
R
EFF : 001-049, 051-099, 101-149, 151-199,
201-249, 251-299, 301-399, 401-499,
76-11-19
Page 408
Nov 01/08
CES
C F M
56-5B
(6) Attach the rod to the fork with the bolt (2) on which the bush (3),
the washer (7) and the nut (6) are assembled. Tighten the bolt.
Subtask 76-11-19-820-052
B. Make sure that you can easily install and remove the rigging pin RIGGING
PIN (98DNSA20206080) (14). If not adjust the rod (12) (Ref. TASK 76-11-
00-820-044)
Subtask 76-11-19-420-055
Subtask 76-11-19-080-052
D. Remove the rigging pin (13) from the artificial feel unit.
R Subtask 76-11-19-869-060
R (a) Move the thrust reverser control lever to the full reverse
R position, then back to the idle position. Make sure that there
R are no hard and/or blocking points over the full travel range.
Subtask 76-11-19-865-060
R F. Remove the safety clip(s) and the tag(s) and close this(these) circuit
breaker(s):
21CE1, 21CE2, 21CE3, 22CE
Subtask 76-11-19-861-051
EFF : 001-049, 051-099, 101-149, 151-199,
201-249, 251-299, 301-399, 401-499,
76-11-19
Page 409
Nov 01/09
CES
C F M
56-5B
Subtask 76-11-19-869-058
(1) Do the EIS start procedure (upper ECAM DU only) (Ref. TASK 31-60-00-
860-001).
(2) On the panel 50VU, make sure that the ENG FADEC GND PWR 1 and 2
pushbutton switches are released (ON LEGENDS COME ON).
Subtask 76-11-19-865-059
-------------------------------------------------------------------------------
PANEL DESIGNATION IDENT. LOCATION
-------------------------------------------------------------------------------
FOR 8KS1
49VU ENGINE/1/FADEC A/AND EIU 1 2KS1 A04
121VU ENGINE/ENG1/FADEC B/AND EIU 1 4KS1 R41
FOR 8KS2
49VU ENGINE/2/FADEC A/AND EIU 2 2KS2 A05
121VU ENGINE/ENG2/FADEC B 4KS2 Q40
Subtask 76-11-19-710-052
R K. Do this test
(2) Move the throttle control lever ENG1(2) and make sure that the small
white circle on N1 indication follows the throttle control lever
position.
EFF : 001-049, 051-099, 101-149, 151-199,
201-249, 251-299, 301-399, 401-499,
76-11-19
Page 410
Nov 01/09
CES
C F M
56-5B
R
EFF : 001-049, 051-099, 101-105, 151-199,
201-233, 236-238, 301-302,
76-11-19
Page 411
Feb 01/08
CES
C F M
56-5B
R
EFF : 106-149, 234-235, 239-249, 251-299,
303-399, 401-499,
76-11-19
Page 412
Nov 01/08
CES
C F M
56-5B
(3) Close circuits breakers 2KS1, 2KS2
(5) Move throttle control lever ENG1(2) and make sure that the small
white circle on N1 indication follows the throttle control lever
position.
(7) Move throttle control lever ENG1(2) and make sure that the small
white circle on N1 indication follows the throttle control lever
position. Make sure that no warning message shows on the upper ECAM
DU.
(8) Do the BITE test of the EFCS (Ref. TASK 27-96-00-740-001) and make
R sure that no message related to the throttle control unit 8KS1(2) is
R shown
5. Close-up
________
Subtask 76-11-19-869-059
(1) On the panel 50VU, release the ENG FADEC GND PWR 1 and 2 pushbutton
switches (ON legends goes off).
Subtask 76-11-19-862-051
Subtask 76-11-19-410-051
C. Close Access
(1) Make sure that the work area is clean and clear of tool(s) and other
items.
EFF : 001-049, 051-099, 101-149, 151-199,
201-249, 251-299, 301-399, 401-499,
76-11-19
Page 413
Nov 01/09
CES
C F M
56-5B
LEVER ASSEMBLY - THROTTLE CONTROL - REMOVAL/INSTALLATION
________________________________________________________
TASK 76-11-41-000-042
1. __________________
Reason for the Job
Self Explanatory
2. ______________________
Job Set-up Information
-------------------------------------------------------------------------------
REFERENCE QTY DESIGNATION
-------------------------------------------------------------------------------
R B. Expendable Parts
R -------------------------------------------------------------------------------
R FIG.ITEM |DESIGNATION |IPC-CSN
R -------------------------------------------------------------------------------
R C. Referenced Information
-------------------------------------------------------------------------------
REFERENCE DESIGNATION
-------------------------------------------------------------------------------
EFF : 001-049, 051-099, 101-149, 151-199,
201-249, 251-299, 301-399, 401-499,
76-11-41
Page 401
Nov 01/09
CES
C F M
56-5B
-------------------------------------------------------------------------------
REFERENCE DESIGNATION
-------------------------------------------------------------------------------
3. __________
Job Set-up
Subtask 76-11-41-865-056
-------------------------------------------------------------------------------
PANEL DESIGNATION IDENT. LOCATION
-------------------------------------------------------------------------------
49VU ENGINE/1 AND 2/IGN/SYS A 1JH A03
49VU FLIGHT CONTROLS/SEC1/NORM/SPLY 21CE1 B08
49VU AUTO FLT/FMGC/1 10CA1 B02
49VU LIGHTING/EMER LT/CKPT/DOME 1LE H08
105VU FLT CTL/SEC1/STBY SPLY 22CE B01
121VU AUTO FLT/FMGC/2 10CA2 M17
121VU ENGINE/IGN/ENG2/SYS B 3JH2 P42
121VU ENGINE/IGN/ENG1/SYS B 3JH1 P41
121VU ENGINE/IGN/ENG2/SYS A BAT 2JH2 P40
121VU ENGINE/IGN/ENG1/SYS A BAT 2JH1 P39
121VU FLIGHT CONTROLS/SEC3/SPLY 21CE3 Q19
121VU FLIGHT CONTROLS/SEC2/SPLY 21CE2 Q18
122VU LIGHTING/INSTL LT/MAIN INST/PNL AND/PED 4LF Y04
122VU LIGHTING/FLOOD/CTR INST/PNL 2LE Z04
Subtask 76-11-41-869-053
B. Make sure that the throttle control levers are at idle (0 degree TLA).
Subtask 76-11-41-941-053
C. Safety Precautions
(1) Put a warning notice in the cockpit to tell persons not to move the
slat and flap control lever.
(a) Put a warning notice to tell persons not to start the engine.
(3) Make sure that the engine 1(2) shutdown occurred not less than 5
minutes before you do this procedure.
(a) Make sure that the ON legend of the ENG/FADEC GND PWR/1(2)
pushbutton switch is off.
EFF : 001-049, 051-099, 101-149, 151-199,
201-249, 251-299, 301-399, 401-499,
76-11-41
Page 402
Nov 01/09
R
CES
C F M
56-5B
(b) Put a warning notice to tell persons not to energize the FADEC
1(2).
Subtask 76-11-41-010-054
D. Get Access
Subtask 76-11-41-010-055
(1) Remove the Multipurpose Control and Display Units 3CA1 and 3CA2
(Ref. TASK 22-82-12-000-001).
(2) Remove the Radio Management Panels 1RG1 and 1RG2 (Ref. TASK 23-13-13-
000-001).
(3) Remove the Audio Control Panels 2RN1 and 2RN2 (Ref. TASK 23-51-12-
000-001).
(4) Remove the Weather Radar Control Unit 3SQ (Ref. TASK 34-41-12-000-
001).
(5) Remove the ATC Control Unit 3SH (Ref. TASK 34-52-12-000-001).
(6) Remove the FLOOD LT/INTEG LT panel 111VU and FLOOD LT panel 112VU.
(Ref. Fig. 401/TASK 76-11-41-991-914)
NOTE : The removal procedure is the same for the FLOOD LT/INTEG LT
____
panel 111VU and FLOOD LT panel 112VU.
(a) Release the fasteners of the panel (1) and disengage the panel
(1) from its housing.
R
EFF : 001-049, 051-099, 101-149, 151-199,
201-249, 251-299, 301-399, 401-499,
76-11-41
Page 403
Nov 01/08
CES
C F M
56-5B
R
EFF : 001-049, 051-099, 101-149, 151-199,
201-249, 251-299, 301-399, 401-499,
76-11-41
Page 404
Nov 01/08
CES
C F M
56-5B
(9) Disconnect the clamps (9).
(12) Remove the pitch trim control mechanism (Ref. TASK 27-41-41-000-001).
4. Procedure
_________
Subtask 76-11-41-480-052
Subtask 76-11-41-020-051
(2) Remove the 2 nuts (31), 2 washers (32) and 2 bolts (34). Make sure
that the 2 bushes (33) stay bonded.
(6) Remove the screw (28) and the hollow pin (24).
(7) Drive out the pin (26). Remove the link (25) and the trigger (27).
(8) Remove the 2 screws (15) and the 2 hollow pins (13).
(9) Remove the lever (29): pull the lever to disconnect the connector
located inside, at the lever-to-bellcrank junction.
(10) Remove the lever (12): do the same procedure as for the lever (29).
R
EFF : 001-049, 051-099, 101-149, 151-199,
201-249, 251-299, 301-399, 401-499,
76-11-41
Page 405
Nov 01/08
CES
C F M
56-5B
R
EFF : 001-049, 051-099, 101-149, 151-199,
201-249, 251-299, 301-399, 401-499,
76-11-41
Page 406
Nov 01/08
CES
C F M
56-5B
EFF : 001-049, 051-099, 101-149, 151-199,
201-249, 251-299, 301-399, 401-499,
76-11-41
Page 407
Nov 01/09
CES
C F M
56-5B
R Throttle Control
Figure 404/TASK 76-11-41-991-917
EFF : 001-049, 051-099, 101-149, 151-199,
201-249, 251-299, 301-399, 401-499,
76-11-41
Page 408
Nov 01/09
CES
C F M
56-5B
Lever Assembly
Figure 405/TASK 76-11-41-991-918
R
EFF : 001-049, 051-099, 101-149, 151-199,
201-249, 251-299, 301-399, 401-499,
76-11-41
Page 409
Nov 01/08
CES
C F M
56-5B
R
EFF : 001-049, 051-099, 101-149, 151-199,
201-249, 251-299, 301-399, 401-499,
76-11-41
Page 410
Nov 01/08
CES
C F M
56-5B
(12) Lift the lighted label (86) and disconnect the connector 21LFA (19).
(17) Remove the 8 nuts (44), the 8 washers (45) and the 8 screws (46).
(18) Remove 2 forward covers (63) and the 2 aft covers (42).
(20) Remove the washer (73), the nut (74), the roller (60) the bushing
(61), the screw (64), the bushing (66), the roller (65) and the link
(25).
(21) Drive out the pin (59) and remove the rocker (57).
(22) Remove the screw (76), the washers (78) and (79) and the 2 clamps
(77).
(23) Remove the screws (80), the washers (81) and (83) and the clamps
(82).
EFF : 001-049, 051-099, 101-149, 151-199,
201-249, 251-299, 301-399, 401-499,
76-11-41
Page 411
Nov 01/09
CES
C F M
56-5B
(29) Remove the shaft (54).
(30) On the bellcrank (41), remove the ball bearing (40), the spacer (47)
and the bearing (48).
(31) On the bellcrank (55) remove the bearing (50), the spacer (51) and
the bearing (52).
R
EFF : 001-049, 051-099, 101-149, 151-199,
201-249, 251-299, 301-399, 401-499,
76-11-41
Page 412
Nov 01/08
CES
C F M
56-5B
TASK 76-11-41-400-042
1. __________________
Reason for the Job
Self Explanatory
2. ______________________
Job Set-up Information
-------------------------------------------------------------------------------
REFERENCE QTY DESIGNATION
-------------------------------------------------------------------------------
B. Consumable Materials
-------------------------------------------------------------------------------
REFERENCE DESIGNATION
-------------------------------------------------------------------------------
C. Expendable Parts
-------------------------------------------------------------------------------
FIG.ITEM |DESIGNATION |IPC-CSN
-------------------------------------------------------------------------------
EFF : 001-049, 051-099, 101-149, 151-199,
201-249, 251-299, 301-399, 401-499,
76-11-41
Page 413
Nov 01/09
CES
C F M
56-5B
D. Referenced Information
-------------------------------------------------------------------------------
REFERENCE DESIGNATION
-------------------------------------------------------------------------------
EFF : 001-049, 051-099, 101-149, 151-199,
201-249, 251-299, 301-399, 401-499,
76-11-41
Page 414
Nov 01/09
R
CES
C F M
56-5B
-------------------------------------------------------------------------------
REFERENCE DESIGNATION
-------------------------------------------------------------------------------
3. __________
Job Set-up
Subtask 76-11-41-865-057
A. Make sure that this(these) circuit breaker(s) is(are) open, safetied and
tagged
-------------------------------------------------------------------------------
PANEL DESIGNATION IDENT. LOCATION
-------------------------------------------------------------------------------
49VU ENGINE/1 AND 2/IGN/SYS A 1JH A03
49VU FLIGHT CONTROLS/SEC1/NORM/SPLY 21CE1 B08
49VU AUTO FLT/FMGC/1 10CA1 B02
49VU LIGHTING/EMER LT/CKPT/DOME 1LE H08
105VU FLT CTL/SEC1/STBY SPLY 22CE B01
121VU AUTO FLT/FMGC/2 10CA2 M17
121VU ENGINE/IGN/ENG2/SYS B 3JH2 P42
121VU ENGINE/IGN/ENG1/SYS B 3JH1 P41
121VU ENGINE/IGN/ENG2/SYS A BAT 2JH2 P40
121VU ENGINE/IGN/ENG1/SYS A BAT 2JH1 P39
121VU FLIGHT CONTROLS/SEC3/SPLY 21CE3 Q19
121VU FLIGHT CONTROLS/SEC2/SPLY 21CE2 Q18
122VU LIGHTING/INSTL LT/MAIN INST/PNL AND/PED 4LF Y04
122VU LIGHTING/FLOOD/CTR INST/PNL 2LE Z04
Subtask 76-11-41-860-051
(1) Make sure that a warning notice is in the cockpit to tell persons not
to move the slat and flap control lever.
(2) On the center pedestal, on the ENG panel 115VU, make sure that a
warning notice is in position to tell persons not to start the
engine.
R
EFF : 001-049, 051-099, 101-149, 151-199,
201-249, 251-299, 301-399, 401-499,
76-11-41
Page 415
Nov 01/08
CES
C F M
56-5B
(3) On the overhead maintenance panel 50VU, make sure that the ON legend
of the ENG/FADEC GND PWR/1(2) pushbutton switch is off. Make sure
that a warning notice is in position to tell persons not to energize
the FADEC 1(2).
Subtask 76-11-41-010-057
C. Get Access
(2) Make sure that the Multipurpose Control and Display Units 3CA1 and
3CA2 are removed (Ref. TASK 22-82-12-000-001).
(3) Make sure that the Radio Management Panels 1RG1 and 1RG2 are removed
(Ref. TASK 23-13-13-000-001).
(4) Make sure that the Audio Control Panels 2RN1 and 2RN2 are removed
(Ref. TASK 23-51-12-000-001).
(5) Make sure that the Weather Radar Control Unit 3SQ is removed
(Ref. TASK 34-41-12-000-001).
(6) Make sure that the ATC Control Unit 3SH is removed (Ref. TASK 34-52-
12-000-001).
(7) Make sure that the FLOOD LT/INTEG LT panel 111VU and FLOOD LT panel
112VU are removed.
(Ref. Fig. 401/TASK 76-11-41-991-914)
(8) Make sure that the pitch trim control mechanism is removed (Ref. TASK
27-41-41-000-001).
(9) Make sure that the RIGGING PIN (98DNSA20208120) (11) is installed in
the artificial feel unit.
(Ref. Fig. 403/TASK 76-11-41-991-916)
4. Procedure
_________
R
EFF : 001-049, 051-099, 101-149, 151-199,
201-249, 251-299, 301-399, 401-499,
76-11-41
Page 416
Nov 01/08
CES
C F M
56-5B
R
EFF : 001-049, 051-099, 101-149, 151-199,
201-249, 251-299, 301-399, 401-499,
76-11-41
Page 417
Nov 01/08
CES
C F M
56-5B
Subtask 76-11-41-420-056
(2) On the bellcrank (41), install a new bearing (40), the spacer (47)
and a new bearing (48).
(3) Engage the shaft (54) and push it. At the same time install:
(4) Push the shaft (54) and install the washer (38) and the nut (37).
(5) TORQUE the nut (37) to between 3 and 4 m.daN (22.12 and 29.49
lbf.ft).
(6) Wirelock the nut (37) with lockwire 0.032 in. (0.8 mm) dia. (Material
No. CP8001) or lockwire 0.032 in. (0.8 mm) dia. (Material No.
CP8002).
(7) Remove the blanking caps from the connectors 2145VC and 2146VC.
(9) Install the clamps (82), the washers (81) and (83) and the screws
(80).
(10) Install the clamps (77), the washers (78) and (79) and the screw
(76).
(12) Install the link (25), the roller (65), the bushing (66), the screw
(64), the bushing (61), the roller (60), the washer (73) and the nut
(74).
R
EFF : 001-049, 051-099, 101-149, 151-199,
201-249, 251-299, 301-399, 401-499,
76-11-41
Page 418
Nov 01/08
CES
C F M
56-5B
(14) Install the 2 forward covers (63) and the 2 aft covers (42).
(15) Install the 8 screws (46), the 8 washers (45) and the 8 nuts (44).
Subtask 76-11-41-220-052
Subtask 76-11-41-420-052
(1) Connect the connector 21LFA (19) on the housing (18) and tighten the
nut of the connector.
R (7) Install the lever (29): push the lever to connect the connector
located inside at the lever-to-bellcrank junction.
R (8) Apply BONDING AND ADHESIVE COMPOUNDS (Material No. 08-007A) on the 2
screws (15).
R (9) Install the 2 screws (15) and the 2 hollow pins (13).
R (10) Assemble the trigger (27) and the link (25) with the pin (26).
R (11) Engage the trigger (27) in the lever (29) and install the hollow pin
(24) and the screw (28).
R (14) Put the two control levers in the idle position (0 degree TLA) and
engage the two links.
R (15) If necessary install 2 new bushings (33) on the screws (34) and bond
them with BONDING AND ADHESIVE COMPOUNDS (Material No. 08-029).
EFF : 001-049, 051-099, 101-149, 151-199,
201-249, 251-299, 301-399, 401-499,
76-11-41
Page 419
Nov 01/09
CES
C F M
56-5B
R (16) Install the 2 screws (34), the 2 washers (32) and the 2 nuts (31).
Subtask 76-11-41-080-052
D. Remove the rigging pin (11) from the artificial feel unit.
5. Close-up
________
Subtask 76-11-41-410-054
A. Close Access
(1) Install the pitch trim control mechanism (Ref. TASK 27-41-41-400-
001).
(7) Install the FLOOD LT/INTEG LT panel 111VU and FLOOD LT panel 112VU.
(Ref. Fig. 401/TASK 76-11-41-991-914)
NOTE : The installation procedure is the same for the panels FLOOD
____
LT/INTEG LT panel 111VU and FLOOD LT panel 112VU.
(a) Remove the blanking caps from the connectors (2) and (3).
(8) Install the Multipurpose Control and Display Units (3CA1 and 3CA2)
(Ref. TASK 22-82-12-400-002).
(9) Install the Radio Management Panels (1RG1 and 1RG2) (Ref. TASK 23-13-
13-400-001).
EFF : 001-049, 051-099, 101-149, 151-199,
201-249, 251-299, 301-399, 401-499,
76-11-41
Page 420
Nov 01/09
CES
C F M
56-5B
(10) Install the Audio Control Panels (2RN1 and 2RN2) (Ref. TASK 23-51-12-
400-001).
(11) Install the Weather Radar Control Unit (3SQ) (Ref. TASK 34-41-12-400-
001).
(12) Install the ATC Control Unit (3SH) (Ref. TASK 34-52-12-400-001).
Subtask 76-11-41-410-055
B. Close Access
(1) Make sure that the work area is clean and clear of tool(s) and other
items.
Subtask 76-11-41-865-058
C. Remove the safety clip(s) and the tag(s) and close this(these) circuit
breaker(s):
1JH, 2JH1, 2JH2, 3JH1, 3JH2, 21CE1, 21CE2, 21CE3, 22CE, 1LE, 2LE, 4LF.
Subtask 76-11-41-861-051
Subtask 76-11-41-710-052
(1) Operate the light adjustment knobs of the FLOOD LT/INTEG LT panel
111VU and FLOOD LT panel 112VU.
(2) Make sure that the light intensity of the glareshield panel 13VU, F/O
glareshield panel 130VU, CAPT glareshield panel 131VU and overhead
control and indicating panel 48VU changes.
Subtask 76-11-41-869-057
R
EFF : 001-049, 051-099, 101-149, 151-199,
201-249, 251-299, 301-399, 401-499,
76-11-41
Page 421
Nov 01/08
CES
C F M
56-5B
Subtask 76-11-41-710-054
(1) Move the ENG1 and ENG2 throttle control levers from MAX REV to MAX
T/O.
(a) On the upper ECAM DU, make sure that the small white circle on
the N1 indication follows the throttle control lever position.
(b) Make sure that the movement is smooth, without friction point.
Subtask 76-11-41-869-058
Subtask 76-11-41-862-051
R
EFF : 001-049, 051-099, 101-149, 151-199,
201-249, 251-299, 301-399, 401-499,
76-11-41
Page 422
Nov 01/08
CES
C F M
56-5B
ENGINE MASTER CONTROL - DESCRIPTION AND OPERATION
_________________________________________________
1. ______________________________
HP Fuel Shut OFF Valve Control
A. General
(Ref. Fig. 001)
The HP fuel shutoff valve control is fully electrical (the HP shutoff
valve is a part of the HMU described in Ref. 73-20-00). It is performed
from the engine panel in the cockpit as follows :
- opening of the HP fuel SOV :
it is controlled by the ECU : the ECU receives the commands from the
ENG/MASTER control switch and ENG/MODE/CRANK/NORM/IGN START selector
switch.
- closure of the HP fuel SOV :
it is controlled directly from the ENG/MASTER control switch in OFF
position (Ref. 73-20-00 and 80-00-00).
B. Valve Operation
(Ref. Fig. 002)
The FADEC control system contains two fuel shut-off means, which act
through pilot valves to close the pressurizing valve :
(2) When the main metering valve is positioned below a minimum fuel flow
position : a mechanically operated pilot valve in the HMU closes the
pressurizing valve. This function is software logic inhibited to
prevent operation at and above idle operation.
The fuel shutoff valve meets the following concepts.
- The pressurizing valve does not actuate open with boost pressure
(even if both pilot valves call for ON) until the HP fuel pump
provides sufficient pressure to open it.
- Loss of power supply does not lead to change the selected HP fuel
shutoff valve position.
- When HP fuel shutoff valve is selected closed (open) a spurious
transient voltage to open (close) does not lead to a permanent
opening (closure) of the fuel valve.
- The cockpit commanded OFF coil has priority over the ECU command.
The cockpit control interfaces directly with the HP fuel shutoff
solenoid. The valve contains a coil which operates the HP shutoff
closed when energized. The solenoid is of a latching type. It latches
either open or closed until a reversing signal is applied. The open
function is a hydraulic trip with a magnetic latch. A closed signal
has priority.
R
EFF : 001-049, 051-099, 101-149, 151-199,
201-249, 251-299, 301-399, 401-499,
76-12-00
Page 1
Nov 01/08
CES
C F M
56-5B
R
EFF : 001-049, 051-099, 101-149, 151-199,
201-249, 251-299, 301-399, 401-499,
76-12-00
Page 2
Nov 01/08
CES
C F M
56-5B
R
EFF : 001-049, 051-099, 101-149, 151-199,
201-249, 251-299, 301-399, 401-499,
76-12-00
Page 3
Nov 01/08
CES
C F M
56-5B
2. ______________________________
LP Fuel Shut Off Valve Control
(Ref. ATA 28)
A. General
The function of the LP fuel shutoff valve is to control the fuel supply
at engine-to-pylon interface.
The valve is located on the engine supply system in the wing leading
edge.
B. Valve Operation
(Ref. Fig. 001)
The LP fuel shutoff valve is controlled :
- From the cockpit overhead panel by means of the ENG FIRE pushbutton
switch
- From the cockpit center pedestal by means of the ENG/MASTER control
switch on engine control panel.
R
EFF : 001-049, 051-099, 101-149, 151-199,
201-249, 251-299, 301-399, 401-499,
76-12-00
Page 4
Nov 01/08
CES