Professional Documents
Culture Documents
Sharp r-1874
Sharp r-1874
Sharp r-1874
MODEL R-1874
In the interest of user-safety, the oven should be restored to its original condition and only parts identical to those specified
should be used.
WARNING TO SERVICE PERSONNEL: Microwave ovens contain circuitry capable of producing very high voltage and
current, contact with following parts may result in a severe, possibly fatal, electrical shock. (High Voltage Capacitor, High
Voltage Power Transformer, Magnetron, High Voltage Rectifier Assembly, High Voltage Harness etc..)
TABLE OF CONTENTS
Page
PRECAUTIONS TO BE OBSERVED BEFORE AND DURING SERVICE TO
AVOID POSSIBLE EXPOSURE TO EXCESSIVE MICROWAVE ENERGY ................... INSIDE FRONT COVER
BEFORE SERVICING ...................................................................................................... INSIDE FRONT COVER
MICROWAVE MEASUREMENT PROCEDURE .....................................................................................................1
WARNING TO SERVICE PERSONNEL..........................................................................................................3
FOREWORD ..........................................................................................................................................................4
PRODUCT SPECIFICATIONS ...............................................................................................................................5
GENERAL INFORMATION ...................................................................................................................................5
PICTORIAL DIAGRAM ..........................................................................................................................................7
CONTROL PANEL CIRCUIT ..................................................................................................................................8
PARTS LIST ..........................................................................................................................................................9
PACKING AND ACCESSORIES ......................................................................................................................... 15
This document has been published to be used for after sales service only. The contents are subject to change without notice.
(IN USA): SHARP ELECTRONICS CORPORATION
Service Headquarters: Sharp Plaza, Mahwah, New Jersey, 07430-2135
OR:
(IN CANADA): SHARP CORPORATION
SHARP ELECTRONICS OF CANADA LTD.
Head Office: 335 Britannia Road East, Mississauga, Ontario L4Z 1W9
(905) 890-2100
R-1874
If the unit operates with the door open, service person should 1) tell the user not to operate the oven
and 2) contact SHARP ELECTRONICS CORPORATION and Food and Drug Administration's Center
for Devices and Radiological Health immediately.
Service personnel should inform SHARP ELECTRONICS CORPORATION of any certified unit found
with emissions in excess of 4mW/cm2. The owner of the unit should be instructed not to use the unit
until the oven has been brought into compliance.
If the unit operates with the door open, service person should 1) tell the user not to operate the oven
and 2) contact SHARP ELECTRONICS OF CANADA LTD. and NHW, CANADA immediately.
Service personnel should inform SHARP ELECTRONICS OF CANADA LTD. of any certified unit
found with emissions in excess of 4mW/cm2. The owner of the unit should be instructed not to use
the unit until the oven has been brought into compliance.
R-1874
1) Microwave leakage limit (Power density limit): The power density of microwave radiation emitted by a microwave oven
should not exceed 1mW/cm2 at any point 5cm or more from the external surface of the oven, measured prior to acquisition
by a purchaser, and thereafter (through the useful life of the oven), 5 mW/cm2 at any point 5cm or more from the external
surface of the oven.
2) Safety interlock switches: Primary interlock relay and door sensing switch shall prevent microwave radiation emission in
excess of the requirement as above mentioned, secondary interlock switch shall prevent microwave radiation emission in
excess of 5 mW/cm2 at any point 5cm or more from the external surface of the oven.
Important:
Survey instruments that comply with the requirement for instrumentation as prescribed by the performance standard
for microwave ovens, 21 CFR 1030.10(c)(3)(i), must be used for testing.
C. Leakage test:
NOTE: After servicing, record data on service invoice and microwave leakage report.
1
R-1874
A. Requirements:
Every microwave oven shall function in such a manner that when the oven is fully assembled and operating with its service
controls and user controls adjusted to yield the maximum output, the leakage radiation, at all points at least 5 cm. from the
external surface of the oven, does not exceed:
1) 1.0mW/cm2 with the test load of 275 15 ml of water at an initial temperature 20 5oC.
2) 5.0mW/cm2 when the outer enclosure is removed with a test load of 275 15 ml of water at an initial temperature 205oC.
3) 5.0mW/cm2 without a test load.
1) Grasp the probe of the survey instrument and hold it perpendicular to the gap between the door and the body of the oven.
2) Move the probe slowly, not faster than 2.5 cm/sec. along the gap, watching for the maximum indication on the meter.
3) Check for leakage at the door screen, sheet metal seams and other accessible positions where the continuity of the metal
has been breached (eg., around the switches, indicator, and vents).
While testing for leakage around the door pull the door away from the front of the oven as far as is permitted by the closed
latch assembly.
4) Measure carefully at the point of highest leakage and make sure that the highest leakage is no greater than 4mW/cm2, and
that the secondary interlock switch does turn the oven OFF before any door movement.
CAUTION: Special attention should be given to avoid electrical shock because HIGH VOLTAGE is generated during this test
No Load test
1) Operate the oven without a load and measure the leakage by the same method as the above test procedure " Leakage
test with enclosure installed"
2. Make sure that the highest leakage should not exceed 5mW/cm2.
NOTE: After servicing, record data on service invoice and microwave leakage report.
2
R-1874
3
R-1874
SUPPLEMENTAL
SERVICE MANUAL PRODUCT DESCRIPTION
MICROWAVE OVEN
FOREWORD
OPERATION
This Manual has been prepared to provide Sharp Electronics Corp.
Service Personnel with Operation and Service Information for the SHARP
MICROWAVE OVEN, R-1874.
The model R-1874 is quite similar to base model R-1855A WIRING DIAGRAM
(Ref.# S99M138R1855E)
Check the interlock switches and the door seal carefully. Special
attention should be given to avoid electrical shock and microwave
radiation hazard.
WARNING
Never operate the oven until the following points are ensured:
(A) The door is tightly closed.
(B) The door brackets and hinges are not defective.
(C) The door packing is not damaged.
(D) The door is not deformed or warped.
(E) There is no other visible damage with the oven.
Servicing and repair work must be carried out only by trained service
personnel.
DANGER
Certain initial parts are intentionally not grounded and present
a risk of electrical shock only during servicing. Service person-
nel - Do not contact the following parts while the appliance is
energized;
High Voltage Capacitor, Power Transformer, Magnetron, High
Voltage Rectifier Assembly, High Voltage Harness;
If provided, Vent Hood, Fan assembly, Cooling Fan Motor.
All the parts marked * on parts list are used at voltages more than
250V.
USA MODEL
OSAKA, JAPAN
4
R-1874
SPECIFICATION
ITEM DESCRIPTION
Power Requirements 120 Volts / 13.2 Amperes (Microwave), 13.2 Amperes (Convection) - [UL Rating]
116 Volts / 13.0 Amperes (Microwave), 13.0 Amperes (Convection) - [CFS Rating]
60 Hertz
Single phase, 3 wire grounded
Power Output 850 watts (IEC-705 TEST PROCEDURE)
Operating frequency of 2450MHz
Convection Power Output 1400 watts
Case Dimensions Width 29-15/16"
Height 16-11/32"
Depth 15- 9/32"
Cooking Cavity Dimensions Width 17-1/8"
Height 8-1/16"
1.1 Cubic Feet Depth 13-13/16"
Hood lamp 2 bulbs, 20W x 2, Incandescent light bulbs
Hood fan Horizontal discharge 230 C.F.M. , Vertical discharge 240 C.F.M. ,
Control Complement Touch Control System
Clock ( 1:00 - 12:59 )
Timer (0 - 99 min. 99 seconds)
Microwave Power for Variable Cooking
Repetition Rate;
P-HI ................................................... Full power throughout the cooking time
P-90 ..................................................................... approx. 90% of Full Power
P-80 ..................................................................... approx. 80% of Full Power
P-70 ..................................................................... approx. 70% of Full Power
P-60 ..................................................................... approx. 60% of Full Power
P-50 ..................................................................... approx. 50% of Full Power
P-40 ...................................................................... approx. 40% of Full Power
P-30 ...................................................................... approx. 30% of Full Power
P-20 ..................................................................... approx. 20% of Full Power
P-10 ....................................................................... approx. 10% of Full Powe
P-0 ...................................................... No power throughout the cooking time
CUSTOM HELP pad, SENSOR COOK pad, COMPU BROIL pad, COMPU ROAST pad
COMPU BAKE pad, SENSOR REHEAT pad, MINUTE PLUS pad, POPCORN pad
COMPU DEFROST pad, CONVECTION pad, REHEAT pad, LOW MIX/BAKE pad
HIGH MIX/ROAST pad, BROIL pad, SLOW COOK pad, KITCHEN TIMER pad
Number and temperature selection pads, CLOCK pad, KEEP WARM pad
TURNTABLE ON / OFF pad, POWER LEVEL pad, STOP/CLEAR pad,
START / TOUCH ON pad, Fan Hi/Lo, Light.
Oven Cavity Light Yes 20W x 1 Incandescent light bulb
Safety Standard UL Listed FCC Authorized
DHHS Rules, CFR, Title 21, Chapter 1, Subchapter J
Canadian Standards Association.
Department of National Health and Welfare CANADA, Industry CANADA.
Weight Approx. 71 lbs.
GENERAL INFORMATION
GROUNDING INSTRUCTIONS
This oven is equipped with a three prong grounding plug. It must be plugged into a wall receptacle that is properly installed and
grounded in accordance with the National Electrical Code and local codes and ordinances.
In the event of an electrical short circuit, grounding reduces the risk of electric shock by providing an escape wire for the electric
current.
WARNING: Improper use of the grounding plug can result in a risk of electric shock.
5
R-1874
Electrical Requirements
The oven is equipped with a 3-prong grounding plug. DO NOT UNDER ANY CIRCUMSTANCES CUT OR REMOVE THE
GROUNDING PIN FROM THE PLUG.
The power supply cord and plug must be connected to a separate 120 Volt AC, 60 Hz, 15 Amp. or more branch circuit, using
a grounded receptacle. The receptacle should be located inside the cabinet directly above the Microwave Oven/Hood
system mounting location.
3-Pronged Plug Grounded
Receptacle Box
Grounding Pin
3-Pronged Receptacle
9
OVEN DIAGRAM
1
8
4 5
3
10
2 7 14
6 6 11
12
13
14. Plug
6
F
C
H
A
F
C
H
A
3 WHT AH. SENSOR
HOOD FAN MOTOR
CN-F 2 RED
1
1
6 BLK
1 BLK 3 BLK
YLW 5 RED BLK
1
6 BLK
1
RED 4 YLW GRY 2 WHT
5 BLK BLU 3 WHT 1 GRN
GRN Power Supply
4 WHT PPL 2 BLK cord 120V 60Hz
CN-E 3 BRN GRY 1 BLU
2 GRN
1 PNK
TEMPERATURE FUSE (MG.)
N.O. STIRRER MOTOR
GRN PNK
GRN R B
to oven cavity COM. WHT E L
front flange D K CONVECTION
RY2: PRIMARY DOOR SENSING SWITCH BLK MOTOR
2
GRN
2
INTERLOCK
2
2
RELAY WHT
GRN
WHT
HEATING
BLK ELEMENT
IC1
BLK
RED Blue RED
COM.
CN-G MONITOR Marking YLW WHT
PPL FUSE AND
CN-E RY3 N.O.
PPL FUSE HOLDER GRY
COM.
CN-F BRN OVEN LAMP & SOCKET
RY2 N.O. BLK 2 BLK
BLK RED
COM. BLK 1 BLK
3
3
N.O. BLK
CN-C RY1 THERMISTOR
BLK
RY9 CN-F
RY10 YLW
3
3
T1
BRN DAMPER
RY8
SWITCH
COM.
HIGH VOLTAGE COMPONENTS
RY6
RY5
RY4
N.O.
BRN
RY7
WHT DAMPER
MOTOR MAGNETRON
CN-B CN-A HIGH VOLTAGE
9 BRN CAPACITOR
7
GRY
4
4
8
7 BLU
PPL
6
F FA
5 BLU
CN-C 4
3 BLK
4
4
2 WHT H.V.
FAN
1 PNK MOTOR RECTIFIER
5
N.C. BLK
5
BLK
7 BLK BLK GRY WHT
6 COM.
MONITOR RED POWER TRANSFORMER
5 BLU SWITCH
4
CN-B 3 RED
2
1 ORG GRY 2 GRY-GRY
PNK 1 BRN-BRN
5 GRY N.O.
B B B
4 WHT L L R TURNTABLE
SECONDARY K K N MOTOR HOOD LAMPS
5
3 YLW COM.
5
CN-A INTERLOCK & SOCKETS
2 GRY SWITCH GRY GRY
HOOD FAN ORG
6
1 RED
6
THERMAL BRN BRN
CUT-OUT WHT
Blue Marking
C
H
A
6
R-1874
Figure S-1. Pictorial Diagram
F
C
H
A
F
C
H
R-1874
T1 C ONT R OL UNIT
(N) A5 5 NOT E
10G 471K
1
VR S 1
1
1
6 D1-D4 : 11E S 1
2 : IF NOT S P E C IF IE E D, 1/4w 5%
d 3 D1 D4
HZ16-1
R 1 4.3k
AC 120V : IF NOT S P E C IF IE E D, 1S S 270A
ZD2
1/2w
C 2 1000/35v
Q4
C 1 0.1/50v
b a
C 3 0.1/50v
ZD3 HZ5C 2
C 4 10/35v
60Hz DT A123E S
+ +
: IF NOT S P E C IF IE E D, 0.01F /16v
C5
R 2 1.5k
R 7 4.7k
4
HZ6A3
D2 D3
(J 1)
HZ4A2
ZD1
C7
ZD4
C 10 0.1/50v
c (V P )
C 100 Q1 2S B1238 R 4 510 1/2w
MOT OR R UN A1
R 8 4.7k
R 3 680 1w R 90 100k
C AP AC IT OR Q3
C8
A3 K R A101M
F LUOR E S C E NT DIS P LAY T UB E
R Y4
2
Q90 K R A101M
2
R 40 3.3k
T UR NT AB LE B1
S P 40
Q20 K R A101M
0.1/50v
MOT OR D20
F 1, 2
C9
MIX C ONV
F 31, 32
R Y5 P1 4 DE F R OS T
F AN MOT OR B3 S E NS OR
Q21 K R A101M IC 2 IZA495DR
D21
10/35v
+
K R A101M
C 11
C 12
R 100 330 1w
R Y6
10
11
12
13
15
16
17
18
19
20
22
23
24
25
26
27
28
29
5
6
7
8
9
DAMP E R B5
MOT OR Q22 K R A101M
D22
P 10
P 11
P 12
P 13
P 14
P 15
P 16
1G
2G
3G
4G
5G
6G
7G
8G
P2
P3
P4
P5
P6
P7
P8
P9
R 91 100k
R 92 100k
R 93 100k
VC C P 30
R Y7 VE E P 31
B7
(J 2)
(J 4)
(J 6)
(J 3)
(J 5)
(J 7)
C ONV E C T ION AV S S P 32
3
3
MOT OR Q23 K R A101M VR E F P 33
D23
AN7 P 34 (C ) (B ) (A)
AN6 P 35
AN5 P 36
R Y8 AN4 P 37
HOOD LAMP C1 AN3 P 00
Q24 K R A101M AN2 P 01
D24
AN1 P 02
AN0 P 03
8
P 55 P 04
C OM P 54 P 05
R Y9 P 53 P 06
C3 P 52 P 07
Q25 K R A101M P 51 P 10
D25
P 50 P 11
IC 1 IZA719DR
P 47 P 12
C9 R Y 10
P 46 P 13
P 45 P 14
HOOD T HE R MO R 65 1k
P 44 P 15
C 21 0.1/50v
P 43 P 16
D26
Q26 K R A101M
4
4
HOOD MOT OR P 42 P 17
C 65
C 20 10/35v
D65
INT 1 P 20
LOW C5 +
100/16v P 40 P 21
RST P 22
+
P 71 P 23
HIG H C7 P 70 P 24
+
R 76 3.3k
R 77 3.3k
R 78 3.3k
R 82 3.3k
XIN P 25
R Y1 XOUT P 26
C OM NO Q30 VS S P 27
3.3k
D74 3.3k
D75 3.3k
(H) K R A101M
R 79
R 80
R 81
D27
Q27
D72
D70
D71
D73
D76
K R C 243M
R 70 3.3k
R 71 3.3k
R 72 3.3k
R 73 3.3k
R 74 3.3k
OV E N LAMP C OM
kF
R Y2 G 1 G 2 G 3 G 4 G 5 G 6 G 7
R 75 100k
R 63 220F R 64 3.6
NO C 30 Q60
K R C 102M C US T OM S E NS OR MINUT E C OMP U S E NS OR C OMP U
D28
C 50 C 60 G 8 P OP C OR N DE F R OS T
MIC R O HE LP R E HE AT P LUS C OOK B R OIL
C F 1 4MHz C 74 330pF
R 30 15k
5
C OM
R 50 15k
5
D32
K IT C HE N
Q29 K R A101M G 11 C LOC K
T IME R 350F 375F 400F 425F 450F
C 71 330pF
TUR NTABLE P OWE R KE E P S T OP S TAR T F AN
G 12 LIG HT
ON / OFF LE V E L WAR M C LE AR TOUC H ON HI/LO
D30 C 70 330pF
K E Y UNIT
E1 E2 E3 E4 E5 E6 F1 F2 F3
6
AH S E NS OR
6
DOOR DAMP E R OV E N
S WIT C H S WIT C H T HE R MIS T OR
C
H
A
R-1874
PARTS LIST
"" MARK: PARTS DELIVERY SECTION.
REF. NO. PART NO. DESCRIPTION Q'TY CODE
ELECTRIC PARTS
1- 1 FH-DZB017MRY0 M High voltage rectifier assembly 1 AM
1- 2 RC-QZA234WRE0 M High voltage capacitor 1 AR
1- 3 QFS-TA013WRE0 M Temperature fuse 150C 1 AG
1- 4 RHET-A174WRE0 M Convection heater 1 AZ
1- 5 RMOTDA211WRE0 M Turntable motor 1 AQ
1- 6 RMOTDA241WRE0 M Stirrer motor 1 AG
1- 7 RTHM-0044MRE0 M Thermal cut-out N.O. 60C 1 AG
1- 8 RTRN-B070MRE0 M Power transformer 1 BF
1- 9 RV-MZA302WRE0 M Magnetron 1 BC
1-10 QFSHDB003MRE0 M Fuse holder 1 AD
1-11 QSW-MA085WRE0 M Secondary interlock, third door sensing and damper switches 3 AE
1-12 FFS-BA018/KIT M Monitor and sec. interlock switch with fuse assembly 1 AF
1-13 FACCDB011MRE0 M Power supply cord 1 AP
1-14 QSOCLB006MRE0 M Hood lamp socket 2 AE
1-15 FH-HZA053WRE0 M Thermistor 1 AP
1-16 QSOCLB006MRE0 M Oven lamp socket 1 AE
1-17 FMOTEA362WRK0 M Hood fan motor 1 BM
1-18 RMOTEA343WRE0 M Convection motor 1 AX
1-19 RMOTEB032MRE0 M Fan motor 1 AW
1-20 RLMPTA068WRE0 M Hood lamp and oven lamp 3 AG
1-21 FDTCTA217WRKZ M AH sensor 1 AW
1-22 RMOTDA242WRE0 M Damper motor 1 AH
1-23 RR-WZA031WRE0 M Noise resistor 1 AK
1-24 FPWBFB014MRK0 M Noise filter 1 AU
CABINET PARTS
2- 1 PFIL-B002MRE0 M Grease filter 2 AF
2- 2 FDIF-B013MRK0 M Hood exhaust louver 1 AW
2- 3 GDAI-B052MRP0A M Base plate right 1 AH
2- 4 GDAI-B039MRP0A M Base plate left 1 AF
2- 5 GCABUB106MRP0 M Outer case cabinet 1 BC
2- 6 TMAPCB063MRR0 M Schematic diagram 1 AB
2- 7 FANGKB009MRY0 M Hood lamp glass assembly 1 AM
2-7-1 LANGQB016MRP0 M Hood lamp glass angle 1 AG
2-7-2 PGLSPB004MRE0 M Hood lamp glass 1 AH
2- 8 PCOVPB030MRT0A M Base cover 1 AX
2- 9 FDECAB028MRK0 M Sash left 1 AL
2-10 LSTY-B010MRP0 M Rear stay 1 AG
CONTROL PANEL PARTS
3- 1 DPWBFB061MRU0 M Control unit 1 BQ
3- 1A QCNCMA227DRE0 J 3-pin connector CN-A 1 AC
3- 1B QCNCMA230DRE0 J 4-pin connector CN-B 1 AC
3- 1C QCNCMA234DRE0 J 5-pin connector CN-C 1 AC
3- 1D QCNCMA267DRE0 J 6-pin connector CN-E 1 AC
3- 1E QCNCMA237DRE0 J 3-pin connector CN-F 1 AD
3- 1F QCNCWA030DRE0 J 12-pin connector CN-G 1 AE
3- 1G RV-KXB003MRE0 M Fluorescent display tube 1 AV
3- 1H PTPEHB010MRE0 M Tape 2mm 1 AB
C1 RC-KZA087DRE0 J Capacitor 0.1 uF 50V 1 AB
C2 VCEAB31VW108M J Capacitor 1000 uF 35V 1 AF
C3 RC-KZA087DRE0 J Capacitor 0.1 uF 50V 1 AB
C4,C12 VCEAB31VW106M J Capacitor 10 uF 35V 2 AB
C5 RC-KZA087DRE0 J Capacitor 0.1 uF 50V 1 AB
C6 VCEAB31VW106M J Capacitor 10 uF 35V 1 AB
C7-8 VCKYD11CY103N J Capacitor 0.01 uF 16V 2 AH
C9-10 RC-KZA087DRE0 J Capacitor 0.1 uF 50V 2 AB
C20 VCEAB31VW106M J Capacitor 10 uF 35V 1 AB
C21 VCEAB31HW104M J Capacitor 0.1 uF 50V 1 AM
C30,C5 VCKYD11CY103N J Capacitor 0.01 uF 16V 2 AH
C50,C11 VCKYD11CY103N J Capacitor 0.01 uF 16V 2 AH
C60 VCKYD11CY103N J Capacitor 0.01 uF 16V 1 AH
C70-74 VCKYD11HB331K J Capacitor 330 pF 50V 5 AA
C100 RC-QZB014MRE0 M Capacitor 7 uF 230V 1 AM
CF1 RCRS-A010DRE0 J Ceramic resonator (CST4.00MGW) 1 AD
D1-4 VHD11ES1///-1 J Diode (11ES1) 4 AB
D20-32 VHD1SS270A/-1 J Diode (1SS270A) 13 AA
D70-76 VHD1SS270A/-1 J Diode (1SS270A) 7 AA
9
R-1874
OVEN PARTS
4- 1 FFTA-B004MRK0 M Exhaust damper assembly 1 AM
4- 2 FROLPB020MRK0 M Turntable support assembly 1 AS
4- 3 NTNT-B006MRE0 M Turntable tray 1 AZ
4- 4 LANGKB010MRP0 M Capacitor holder 1 BB
4- 5 FCOVPB002MRY0 M Stirrer cover assembly 1 AM
4- 6 FFAN-B008MRK0 M Stirrer fan assembly 1 AL
4- 7 ------------- M Oven cavity (not replaceable) 1 AP
4- 8 DHET-B001MRK0 M Convection heater unit 1 AT
4- 9 NCPL-B007MRF0 M Coupling 1 AE
4-10 NFANMB003MRK0 M Convection motor fan 1 AE
4-11 LANGQB031MRP0 M Convection motor angle 1 AF
4-12 PPACGB013MRE0 M Turntable motor packing 1 AC
4-13 LBNDK0054WRE0 M Heater mounting holder 2 AD
4-14 NFANMB004MRP0 M Convection fan 1 AE
4-15 PHOK-B013MRF0 M Latch hook 1 AG
4-16 FANGTB003MRY0 M Unit mounting plate 1 AV
4-17 PFPF-B002MRE0 M Heat protect L 1 AK
4-18 PPIPFB002MRE0 M Coller 1 AD
4-19 PREFHB006MRP0 M Heater cover L 1 AM
4-20 PDUC-B083MRP0 M Hood intake duct L 1 AG
4-21 NFANPB005MRE0 M Fan blade 1 AC
4-22 GBDYRB002MRP0 M Back plate 1 AX
4-23 FDUC-B046MRK0 M Fan duct 1 AM
10
R-1874
11
R-1874
12
R-1874
1 2 3 4 5 6
4-52
4-50
4-50 4-51
7-24 4-16
7-7
B B
7-24
4-39 2-10
4-46
4-36 7-11
4-56 4-25
7-7 7-24 7-24
4-37
C 1-21 4-24 C
4-45 7-11
7-3 4-40
7-17 1-13 2-5
4-38
7-5
2-6
7-7 7-7 7-11
4-44 7-20 4-22
1-7
4-8
4-20 7-5
D 7-21 1-16 4-54 7-7 D
7-14 7-15 2-9 1-6
1-20 7-7
7-23 1-3
1-18 4-18 4-7
7-14 1-4 7-1
4-10
7-20
4-11 7-4
4-19 4-4
6-13
1-15
4-12 7-16
E 4-13 E
1-2
4-43 1-1
1-9
7-12 7-1
7-25 1-24
7-12 7-13 4-23
4-17 4-9 4-21
7-19 4-53 4-55
7-6
7-22 1-11 4-41
4-14 1-10
4-34 4-15
7-26 7-18 6-12 4-26 7-9
4-13 1-5 1-12
7-12 7-22 7-16
7-20 4-50
F 2-2 4-33 1-8 F
1-20 4-27 1-19 1-11
4-6 4-48
4-29
1-20 1-11
7-26 7-5
1-14 4-31
4-5 2-4
7-5 1-7 4-28 4-49
1-14 1-22
7-25 1-23 7-7 4-47
2-8 7-7
G 4-3 7-7 4-30 G
6-14
2-1 7-7 4-32 7-20
2-3
6-16
4-42
7-10 7-7
2-7 2-1
4-2
7-10
2-7-2
2-7-1
H 7-8 H
7-2
1 2 3 4 5 6
13
R-1874
1 2 3 4 5 6
A A
3-3
3-2
3-2 -2
3-2 -5
3-2 -1 3-3
B 6-1 5 B
7-7
3-1
4-35
3-2 -4
3-2 -3
5-5
C C
5-2
5-10
5-9
5-7
5-6
D D
5-1
5-8
E 5-3 E
5-4
6-1
F F
6-8
6-1-1 6-6
6-1-4
6-1-5
6-1-2
6-1-6
6-1-3 6-1-7
G G
6-9 6-10
6-11
H H
1 2 3 4 5 6
14
R-1874
6-1
INSTALL MATERIAL ASSEMBLY
6-7 COOK BOOK
4-2 TURNTABLE
SUPPORT Non-replaceable items
ASSEMBLY
TRAY HOLDER
15
R-1874
NOTES
16
R-1874
NOTES
17
R-1874
18