Professional Documents
Culture Documents
BS 1881 122 Concrete Testing Water Absorbtion PDF
BS 1881 122 Concrete Testing Water Absorbtion PDF
Licensed Copy: lbocvzr lbocvzr, University of Loughborough, 21 February 2004, Uncontrolled Copy, (c) BSI
Testing concrete
Part 122: Method for determination of
water absorption
Licensed Copy: lbocvzr lbocvzr, University of Loughborough, 21 February 2004, Uncontrolled Copy, (c) BSI
UDC 666.972.017:691.32:620.1
BS 1881-122:1983
Cooperating organizations
British Ready Mixed Concrete Association* Institution of Water Engineers and Scientists*
British Steel Industry National Federation of Building Trades
Cement Admixtures Association Employers*
Cement and Concrete Association* Natural Environment Research Council
Cement Makers Federation* (Institute of Geological Science)
Chemical Industries Association Royal Institute of British Architects*
Concrete Society Limited* Royal Institution of Chartered Surveyors*
County Surveyors Society* Sand and Ballast Hauliers and Allied Trades
Department of the Environment (Building Alliance
Research Establishment)* Sand and Gravel Association Limited*
Department of the Environment (PSA)* Society of Chemical Industry*
Department of the Environment (Transport Stone Federation
and Road Research Laboratory)*
The organizations marked with an asterisk in the above list, together with the
following, were directly represented on the Technical Committee entrusted
with the preparation of this British Standard:
Contents
Page
Cooperating organizations Inside front cover
Foreword ii
1 Scope 1
2 Definitions 1
3 Apparatus 1
4 Test specimens 1
5 Procedure 1
6 Calculation and expression of results 1
7 Test report 2
Figure 1 Correction factor 3
Licensed Copy: lbocvzr lbocvzr, University of Loughborough, 21 February 2004, Uncontrolled Copy, (c) BSI
BSI 12-1998 i
BS 1881-122:1983
Foreword
This Part of this standard prepared under the direction of the Cement, Gypsum,
Aggregates and Quarry Products Standards Committee, is a revision of clause 7
of BS 1881-5:1970, which has been deleted by Amendment No. 1 to that standard.
The water absorption test in this Part is basically unchanged from that in
the 1970 edition. No estimate of repeatability or reproducibility is given in this
Part of this British Standard. Reference should be made to BS 5497-1 for further
information on the determination of repeatability and reproducibility.
A British Standard does not purport to include all the necessary provisions of a
contract. Users of British Standards are responsible for their correct application.
Compliance with a British Standard does not of itself confer immunity
from legal obligations.
Licensed Copy: lbocvzr lbocvzr, University of Loughborough, 21 February 2004, Uncontrolled Copy, (c) BSI
Summary of pages
This document comprises a front cover, an inside front cover, pages i and ii,
pages 1 to 4, an inside back cover and a back cover.
This standard has been updated (see copyright date) and may have had
amendments incorporated. This will be indicated in the amendment table on
the inside front cover.
ii BSI 12-1998
BS 1881-122:1983
1 Scope NOTE One end of each specimen should preferably be from one
of the faces which would normally be exposed when the unit is in
This Part of this British Standard specifies a use.
method for the determination of water absorption of 4.2 Measurement of density. Measure the density
concrete specimens cored from a structure or of the specimens in accordance with BS 1881-114.
precast component.
4.3 Measurement of dimensions. Measure the
NOTE The titles of the publications referred to in this standard dimensions of the specimen in accordance with
are listed on the inside back cover.
BS 1881-114.
2 Definitions 4.4 Age of specimens at test. The test for
absorption shall be made when the age of the
For the purposes of this Part of this standard the
concrete is 28 days to 32 days, which means that
definitions given in BS 5328 apply.
drying of the specimens shall begin at an age
Licensed Copy: lbocvzr lbocvzr, University of Loughborough, 21 February 2004, Uncontrolled Copy, (c) BSI
BSI 12-1998 1
BS 1881-122:1983
The correction factor related to size is based on the 7.3 Information to be provided by the test
formula laboratory for inclusion in the test report. The
3 following information shall be provided by the test
volume ( mm )
correction factor = ------------------------------------------------------------------------ laboratory for inclusion in the test report:
2
surface area ( mm ) 12.5
a) identification of the test specimen;
7 Test report b) condition of specimen when received (include
7.1 General. The report shall affirm that the tests poor compaction and honeycombing);
were carried out in accordance with this Part of this c) date of receipt of the specimen;
standard. The report shall also state whether or not d) dimensions of the specimen;
certificates of sampling, specimen preparation and
curing are available. If available, a copy of each e) conditions of storage and curing until test date;
certificate shall be provided. f) date of beginning of tests (placing in oven);
Licensed Copy: lbocvzr lbocvzr, University of Loughborough, 21 February 2004, Uncontrolled Copy, (c) BSI
2 BSI 12-1998
Licensed Copy: lbocvzr lbocvzr, University of Loughborough, 21 February 2004, Uncontrolled Copy, (c) BSI
BSI 12-1998
Figure 1 Correction factor
3
BS 1881-122:1983
BS 1881-122:1983
Testing concrete
Summary of published British Standards
Due to the present restructuring of BS 1881 Methods of testing concrete and BS 4408 Recommendations for non-destructive methods
of test for concrete, the following information has been published, to help keep readers up-to-date, with the situation so far.
(February 1983).
4 BSI 12-1998
BS 1881-122:1983
Publications referred to
BSI 12-1998
|
|
|
|
|
|
|
|
|
BSI British Standards Institution
|
|
|
|
|
|
| BSI is the independent national body responsible for preparing British Standards. It
|
| presents the UK view on standards in Europe and at the international level. It is
| incorporated by Royal Charter.
|
|
| Revisions
|
|
| British Standards are updated by amendment or revision. Users of British Standards
|
| should make sure that they possess the latest amendments or editions.
|
|
| It is the constant aim of BSI to improve the quality of our products and services. We
|
| would be grateful if anyone finding an inaccuracy or ambiguity while using this
| British Standard would inform the Secretary of the technical committee responsible,
|
| the identity of which can be found on the inside front cover. Tel: 020 8996 9000.
|
| Fax: 020 8996 7400.
Licensed Copy: lbocvzr lbocvzr, University of Loughborough, 21 February 2004, Uncontrolled Copy, (c) BSI
|
|
| BSI offers members an individual updating service called PLUS which ensures that
|
| subscribers automatically receive the latest editions of standards.
|
|
| Buying standards
|
| Orders for all BSI, international and foreign standards publications should be
|
| addressed to Customer Services. Tel: 020 8996 9001. Fax: 020 8996 7001.
|
|
| In response to orders for international standards, it is BSI policy to supply the BSI
|
| implementation of those that have been published as British Standards, unless
|
| otherwise requested.
|
|
| Information on standards
|
| BSI provides a wide range of information on national, European and international
|
| standards through its Library and its Technical Help to Exporters Service. Various
|
| BSI electronic information services are also available which give details on all its
|
| products and services. Contact the Information Centre. Tel: 020 8996 7111.
|
| Fax: 020 8996 7048.
|
|
| Subscribing members of BSI are kept up to date with standards developments and
| receive substantial discounts on the purchase price of standards. For details of
|
| these and other benefits contact Membership Administration. Tel: 020 8996 7002.
|
| Fax: 020 8996 7001.
|
|
| Copyright
|
|
| Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of
|
| the publications of the international standardization bodies. Except as permitted
| under the Copyright, Designs and Patents Act 1988 no extract may be reproduced,
|
| stored in a retrieval system or transmitted in any form or by any means electronic,
|
| photocopying, recording or otherwise without prior written permission from BSI.
|
|
| This does not preclude the free use, in the course of implementing the standard, of
|
| necessary details such as symbols, and size, type or grade designations. If these
|
| details are to be used for any other purpose than implementation then the prior
| written permission of BSI must be obtained.
|
|
| If permission is granted, the terms may include royalty payments or a licensing
|
| agreement. Details and advice can be obtained from the Copyright Manager.
|
| Tel: 020 8996 7070.
|
|
|
|
|
|
|
|
|
BSI |
|
389 Chiswick High Road |
|
London |
|
W4 4AL |
|
|
|
|
|
|