Professional Documents
Culture Documents
AGA 3 Gas Flow Equation For Orifice Plates - Learning Instrumentation and Control Engineering
AGA 3 Gas Flow Equation For Orifice Plates - Learning Instrumentation and Control Engineering
com/dyn-
css/authorization.css?targetBlogID=5624717864455829484&zx=c1e7b340-
5a34-4c63-bf0d-0346450222c2' rel='stylesheet'/>
Top of Form
partner-pub-6021 ISO-8859-1 Search
Bottom of Form
Custom Search
Recall that we have discussed the ISO 5167 Orifice Meter Equation. While some
companies use the ISO 5167 orifice gas flow equation, a vast majority of companies
use the American Gas Association committee report 3 gas flow equation otherwise
referred to as AGA 3 Gas Flow Equation for Orifice Plates. The flow rate computed
by this equation is in standard units i.e Standard Cubic Feet per Hour or SCFH.
Any equation computing flow in standard units must predict the effective expansion of
the gas as if
it were to transition from flowing conditions (the actual pressure and temperature it
experiences flowing through the pipe or pipeline) to standard conditions (1
atmosphere, 60 degrees Fahrenheit).
The compensated gas flow measurement equation published by the American Gas
Association (AGA Committee Report 3) in 1992 for orifice plates with flange taps
calculates this gas expansion to standard conditions with a series of factors accounting
for flowing and standard (base) conditions. Most of these factors are represented in
the AGA3 equation by different variables as shown below:
Note that SQRT in the explanations below for the AGA 3 flow equation means Square
Root of the term in bracket
Where:
Q = Volumetric flow rate in standard cubic feet per hour - SCFH
Fc = Orifice calculation factor (a polynomial function of the orifice plates ratio and
Reynolds number), appropriate for flange taps.
Fsl = Slope factor (another polynomial function of the orifice plates ratio
and Reynolds number), appropriate for flange taps.
Pf1 = Flowing pressure of gas at the upstream tap PSIA (in PSI absolute)
The Callendar Van Dusen Equation for Platinum Based RTD Thermometers
Process Transmitters Voltage and Power Requirements in a Two-Wire 4 20mA Current Loop
Process Transmitters Voltage and Power Requirements in a Two-Wire 4 20mA Current Loop
The Callendar Van Dusen Equation for Platinum Based RTD Thermometers
Recommended by
Recent Posts
Control Valve Actuators Failure Modes
Control valves can be built from various ... read more
Apr 30 2017
Basics of Split-Range Control in Control Valve Applications
In many process control applications in industry, ... read more
Apr 30 2017
How a Self Operated Pressure Reducing Regulator Works
A self operated pressure reducing regulator is a ... read more
Apr 20 2017
What is Damping in Process Transmitters
A process transmitter typically measures a ... read more
Apr 05 2017
ANSI B16.5 - Maximum Pressure and Temperature Ratings of Flanges and Flange Fittings
The Maximum allowable non-shock pressure (psig) ... read more
Apr 02 2017
Instrumentation Blog Your browser does not support JavaScript!
Popular Posts
Common P&ID symbols used in Developing Instrumentation Diagrams
Instrument Abbreviations Used in Instrumentation Diagrams (P&ID)
How a Pressure Switch Works
How to Calibrate Your DP Transmitter
Piping and Instrumentation Diagrams:Tutorials I
How to Read and Interpret Piping and Instrumentation Diagrams (P&ID)
Basics of Piping and Instrumentation Diagrams (P&IDs)
How a Current to Pressure Transducer (I/P) Works
How to Calibrate a Pressure Gauge With a Dead Weight Tester
How to Convert Thermocouple Milivolts to Temperature
Translate
Submit
LearningElectrica en_US
Bottom of Form
Categories
Control Valves ( 32 ) Flow meters ( 22 ) Temperature sensors ( 22 ) Calibration ( 19 )
Instrumentation Diagrams ( 19 ) Level Measurement ( 15 ) DP Transmitters ( 14 ) Orifice Plates (
11 ) Thermocouples ( 11 ) Transmitters ( 11 ) Pneumatic Systems ( 10 ) Pressure Switch ( 10 ) RTD (
9 ) pressure sensors ( 9 ) Process Control ( 7 ) Electrical Noise ( 6 ) Electricals ( 6 ) HART Protocol (
6 ) Pressure Gauges ( 6 ) 4 - 20mA Signals ( 4 ) Basics of Instrumentation ( 4 ) Digital or Analog
Multimeters ( 2 ) Fluke pressure calibrator ( 2 ) Instrumment Engineers ( 2 ) Thermowells ( 2 )
Electric Motors ( 1 ) Instrument Engineers ( 1 ) Measurement terminology ( 1 ) Motor Nameplate (
1)
Advertisement
UgvIXcnMITqs+Q
Explore Instrumentationtoolbox.com
Flow Meters :
Theory of Fluid Flow
Meters Differential Pressure (DP)
Electronic Flow Meters Transmitters :
Mechanical Flow An Introduction to DP
Piping and
Meters Transmitters
Instrumentation
Differential Pressure Troubleshooting Guide of
Diagrams :
Flow Meters DP Transmitters
How to Read and
Mass Flow Meters How to Calibrate Your DP
Interpret P&IDs
Flow Meter Selection Transmitter
Understanding P&ID
Guide Common Terms Used in
Drawings
How a Turbine Flow DP Transmitter
Basic Functions of
Meter Works Calibration
Instruments in a P&ID
Principles of Flow DP Transmitter Valve
P&IDs: Piping Line
Metering Manifolds
Number Identification
Applications of DP
Basics of P&IDs
Pressure and Process Transmitters
Instrument
Switches : Electronic Transmitters
Abbreviations Used in
How a Pressure Switch Wire Configuration
P&IDs
Works How to Calibrate DP
Common Process
How a Differential Transmitters
Equipment Symbols I
Pressure Switch Works
Common Process
Pressure Switch Thermocouples :
Equipment Symbols II
Designs and Temperature
Common Terms Used to
Applications Measurments with
Interpret P&ID
How to Select a Thermocouples
Drawings
Pressure Switch Practical Application Tips
Understanding For Thermocouples
P&IDs Tutorials:
Pressure Switch Selection Factors for
P&IDs: Tutorials I
Terminology Thermocouples
P&IDs Tutorials II:
Calibrating a Pressure How to Convert
Pressure Control
Switch with a Fluke Thermocouple Milivolts
P&IDs Tutorial III: Flow
Calibrator to Temperature
and Level Control
How to Calibrate and Reducing Noise in
Adjust a Pressure Thermocouple
Switch Installations
Process Switches
Symbols