Professional Documents
Culture Documents
List of Suggested Reviewers or Reviewers Not To Include (Optional)
List of Suggested Reviewers or Reviewers Not To Include (Optional)
SUGGESTED REVIEWERS:
Not Listed
1503853
FOR CONSIDERATION BY NSF ORGANIZATION UNIT(S) (Indicate the most specific unit known, i.e. program, division, etc.)
EMPLOYER IDENTIFICATION NUMBER (EIN) OR SHOW PREVIOUS AWARD NO. IF THIS IS IS THIS PROPOSAL BEING SUBMITTED TO ANOTHER FEDERAL
TAXPAYER IDENTIFICATION NUMBER (TIN) A RENEWAL AGENCY? YES NO IF YES, LIST ACRONYM(S)
AN ACCOMPLISHMENT-BASED RENEWAL
436003859
NAME OF ORGANIZATION TO WHICH AWARD SHOULD BE MADE ADDRESS OF AWARDEE ORGANIZATION, INCLUDING 9 DIGIT ZIP CODE
University of Missouri-Kansas City
University of Missouri-Kansas City
5100 Rockhill Road
AWARDEE ORGANIZATION CODE (IF KNOWN)
Kansas City, MO. 641102499
0025189000
NAME OF PRIMARY PLACE OF PERF ADDRESS OF PRIMARY PLACE OF PERF, INCLUDING 9 DIGIT ZIP CODE
University of Missouri-Kansas City
University of Missouri-Kansas City
5100 Rockhill Rd
Kansas City ,MO ,641102446 ,US.
IS AWARDEE ORGANIZATION (Check All That Apply) SMALL BUSINESS MINORITY BUSINESS IF THIS IS A PRELIMINARY PROPOSAL
(See GPG II.C For Definitions) FOR-PROFIT ORGANIZATION WOMAN-OWNED BUSINESS THEN CHECK HERE
TITLE OF PROPOSED PROJECT A Quadrotor-based Mechatronics Design Course for Improved Information
Retention
REQUESTED AMOUNT PROPOSED DURATION (1-60 MONTHS) REQUESTED STARTING DATE SHOW RELATED PRELIMINARY PROPOSAL NO.
IF APPLICABLE
$ 250,000 24 months 06/01/15
THIS PROPOSAL INCLUDES ANY OF THE ITEMS LISTED BELOW
BEGINNING INVESTIGATOR (GPG I.G.2) HUMAN SUBJECTS (GPG II.D.7) Human Subjects Assurance Number
DISCLOSURE OF LOBBYING ACTIVITIES (GPG II.C.1.e) Exemption Subsection or IRB App. Date Pending
PROPRIETARY & PRIVILEGED INFORMATION (GPG I.D, II.C.1.d) INTERNATIONAL ACTIVITIES: COUNTRY/COUNTRIES INVOLVED (GPG II.C.2.j)
HISTORIC PLACES (GPG II.C.2.j)
VERTEBRATE ANIMALS (GPG II.D.6) IACUC App. Date
COLLABORATIVE STATUS
PHS Animal Welfare Assurance Number
FUNDING MECHANISM Research - other than RAPID or EAGER Not a collaborative proposal
PI/PD DEPARTMENT PI/PD POSTAL ADDRESS
Civil Mechanical Engineering 5100 Rockhill Road
PI/PD FAX NUMBER
Kansas City, MO 641102499
United States
NAMES (TYPED) High Degree Yr of Degree Telephone Number Email Address
PI/PD NAME
Travis D Fields PhD 2013 816-235-1291 fieldstd@umkc.edu
CO-PI/PD
Gregory W King PhD 2006 816-235-2350 kinggr@umkc.edu
CO-PI/PD
Jacob M Marszalek PhD 2006 816-235-1303 marszalekj@umkc.edu
CO-PI/PD
CO-PI/PD
Page 1 of 3
Not for distribution
CERTIFICATION PAGE
Certification for Authorized Organizational Representative (or Equivalent) or Individual Applicant
By electronically signing and submitting this proposal, the Authorized Organizational Representative (AOR) or Individual Applicant is: (1) certifying that statements made herein are true and
complete to the best of his/her knowledge; and (2) agreeing to accept the obligation to comply with NSF award terms and conditions if an award is made as a result of this application. Further,
the applicant is hereby providing certifications regarding conflict of interest (when applicable), drug-free workplace, debarment and suspension, lobbying activities (see below),
nondiscrimination, flood hazard insurance (when applicable), responsible conduct of research, organizational support, Federal tax obligations, unpaid Federal tax liability, and criminal
convictions as set forth in the NSF Proposal & Award Policies & Procedures Guide,Part I: the Grant Proposal Guide (GPG). Willful provision of false information in this application and its
supporting documents or in reports required under an ensuing award is a criminal offense (U.S. Code, Title 18, Section 1001).
Debarment and Suspension Certification (If answer "yes", please provide explanation.)
Is the organization or its principals presently debarred, suspended, proposed for debarment, declared ineligible, or voluntarily excluded
from covered transactions by any Federal department or agency? Yes No
By electronically signing the Certification Pages, the Authorized Organizational Representative (or equivalent) or Individual Applicant is providing the
Debarment and Suspension Certification contained in Exhibit II-4 of the Grant Proposal Guide.
By electronically signing the Certification Pages, the Authorized Organizational Representative (or equivalent) or Individual Applicant located in FEMA-designated special flood hazard areas is
certifying that adequate flood insurance has been or will be obtained in the following situations:
(1) for NSF grants for the construction of a building or facility, regardless of the dollar amount of the grant; and
(2) for other NSF grants when more than $25,000 has been budgeted in the proposal for repair, alteration or improvement (construction) of a building or facility.
Page 2 of 3
Not for distribution
By electronically signing the Certification Pages, the Authorized Organizational Representative (or equivalent) is certifying that the corporation has no unpaid Federal tax liability that has
been assessed, for which all judicial and administrative remedies have been exhausted or lapsed, and that is not being paid in a timely manner pursuant to an agreement with the authority
responsible for collecting the tax liability.
By electronically signing the Certification Pages, the Authorized Organizational Representative (or equivalent) is certifying that the corporation has not been convicted of a felony criminal
violation under any Federal law within the 24 months preceding the date on which the certification is signed.
fm1207rrs-07
816-235-5600 ORS@umkc.edu 816-235-6532
Page 3 of 3
NATIONAL SCIENCE FOUNDATION
Division of Undergraduate Education
Project Data:
A. Major Discipline Code: 56
B. Academic Focus Level of Project: UP
C. Highest Degree Code: D
D. Category Code: --
E. Business/Industry Participation Code: NA
F. Audience Code:
G. Institution Code: PUBL
H. Strategic Area Code:
I. Project Features: 1 2 3 4
Estimated number in each of the following categories to be directly affected by the activities of the project
during its operation:
J. Undergraduate Students: 100
K. Pre-college Students: 60
L. College Faculty: 3
M. Pre-college Teachers: 0
N. Graduate Students: 1
Page A
TABLE OF CONTENTS
For font size and page formatting specifications, see GPG section II.B.2.
Table of Contents 1
References Cited 2
Budget 5
(Plus up to 3 pages of budget justification)
Appendix Items:
*Proposers may select any numbering mechanism for the proposal. The entire proposal however, must be paginated.
Complete both columns only if the proposal is numbered consecutively.
PROJECT DESCRIPTION A Quadrotor-based Mechatronics Design Course for
Improved Information Retention
1. INTRODUCTION
The objective of the proposed project is to develop and incorporate a newly mandated senior-
level course for mechanical engineering students focused on mechatronics design into
existing curriculum. The redesigned course ME 457 Mechatronics System Design builds on
existing course offerings in instrumentation (ME 352 Instrumentation and Measurements
Laboratory) and controls (ME 415 Feedback Control Systems) by incorporating a central
project to design, construct, and test a quadrotor unmanned aircraft system (UAS). While
success in the mechatronics course is heavily dependent on students proficiency in the
preceding course sequence, the implementation of a comprehensive design project requiring
application of concepts learned in the preceding courses will likely facilitate a deeper level of
understanding with less review of old material and better retention rates, in comparison to a
traditionally-implemented mechatronics course design. The proposed project consists of two
objectives:
1.1. Significance
Over the past 20 years there has been a significant increase in the demand for integration of
mechanics, electronics, control systems, and computer science [1]. However, mechanical
engineering students do not typically learn the necessary skills to design these mechatronic
systems as a part of the required core curriculum. The Mechanical Engineering faculty at the
University of Missouri-Kansas City (UMKC) recently introduced a three-course
mechatronics sequence as part of their required curriculum to improve students proficiency
and marketability in the high-demand field of mechatronics engineering. The first course, ME
352 Instruments and Measurements, is already being taught at UMKC and integrates
standard mechanical instrumentation theory with data acquisition and analysis. Typical
instruments and sensors used in mechatronics-related projects are introduced in this course,
including accelerometers, rate gyros, magnetometers, and ultrasonic ping sensors, to provide
students with the necessary hardware foundation prior to the design phase of the course
sequence. The second course, ME 415 Feedback Control Systems, is also an existing course
that introduces students to theoretical components of feedback control design. The proposed
work involves development of a third course, ME 457 Mechatronics Systems Design, which
represents the culmination of the three-course sequence. In Mechatronics Systems Design,
students will design, build, and test a quadrotor unmanned aircraft system (UAS). This course
provides opportunities for students to develop the typically undervalued [2] skill of applying
mechanical design to a complicated mechatronic system. The new course sequence will offer
the highly valued balance between theory and practice [3] by exposing students to a
combination of laboratory and lecture-based courses.
Maintaining a focused theme in the form of a directed student project throughout the
Mechatronics Systems Design course provides an ideal scenario for longitudinal student
assessment of information retention and self-efficacy in comparison to typical capstone
1
design courses generally require each student team to complete a different project. Such
variation in project scope can potentially limit the potential of student learning assessment.
Being cognizant of the difficulties many universities face with limited specialization in
mechatronics and/or aerospace, dissemination will be tailored such that other universities
could easily adopt the Mechatronics Systems Design course developed at UMKC. An
UMKC-hosted webpage will be developed with all course information and software in
addition to typical publication methods. In order to improve widespread dissemination,
publication will be sought through electronics hobbyist periodicals Make Magazine and Nuts
& Volts as well as the wildly popular SparkFun.com online electronics retailer.
1.2. Background
Mechatronics Education and Information Retention.
The Mechanical Engineering faculty at UMKC have decided to modify their curriculum such
that students are required to take a three-course mechatronics sequence including ME 352
Instrumentation and Measurements, ME 415 Feedback Control Systems, and ME 457
Mechatronics Systems Design to better meet ABET obligations. The course sequence
provides opportunities for students to develop hands-on skills and become proficient in
feedback control theory, and apply both in a comprehensive project introduced at the end of
the sequence. The specific focus of this proposal is to develop the third course in the
mechatronics sequence (Mechatronics Systems Design). Such a course is expected to nurture
the teamwork, design, and communication skills typically only achieved in a capstone course.
The course also provides an ideal opportunity to integrate emerging technology into the
classroom, thereby giving students first-hand experience with relevant skills for their future
careers. The benefits of such an immersive hands-on experience have been well documented
in engineering education literature [4-6], and are expected to impact information retention by
incorporating material that relies heavily upon previous course material. By requiring
students to perform experiments and design control systems without instructional review, the
students will be forced to recall/reteach themselves the material they are expected to know. It
is hypothesized that the students will retain more of the curriculum material after the course
sequence has been completed, in comparison to students taking the existing curriculum.
Technological advances over the past few decades have brought cheaper, smaller, and more
powerful microcontroller units to the everyday consumer. Mechatronics education has
needed to adapt to the influx of new hardware available by providing both theoretical lecture
content and hands-on laboratory components [7]. Many universities have adopted elective-
based mechatronics courses, but few mechanical engineering programs have implemented a
required course in mechatronics [8]. Recognizing the increasing need for engineers in this
field, the UMKC Mechanical Engineering faculty has deemed mechatronics an important
core to which each student should be exposed to prior to graduation. The proposed course
prescribes a coherent set of laboratory activities that provide students the opportunity to
develop skills needed to accomplish the semester project task of creating a complete
unmanned aircraft capable of stable flight in a controlled environment.
2
method in which a multirotor vehicle delivers a package directly to the customers residence
autonomously. Lady Gaga also utilized a multirotor by riding in the worlds first flying
dress in which she was lifted in the air by a 400 lb. multirotor system in front of a live
audience [10]. There has been significant interest in utilizing multirotors for a variety of
applications and, accordingly, mechanical engineering students have shown great interest in
creating their own flying vehicles.
The unmanned aircraft systems industry is expected to grow substantially over the next
decade, tying course content directly into the merging field of UAS. The Federal Aviation
Administration has demonstrated its commitment to the utilization of UAS in the recently
announced decision for the six UAS testing locations; with new airspace integration
procedures expected late 2014-early 2015 (for small UAS) [11]. This course provides
students with the necessary skills and knowledge to successfully enter the emerging UAS
industry by providing students with single, hands-on UAS project. As UAS are integrated
into the national airspace, the number of applications for UAS will greatly increase beyond
the already large range of applications already developed. Prior to completing the course
students will have a strong foundation in mechatronics, instrumentation, feedback control
theory, and will be able to apply these skills to modern problems.
Quadrotors are particularly simple dynamic systems, when compared with other flying
vehicle types. Due to the relative simplicity of a quadrotor vehicle, modeling, parameter
estimation, and control design of the UAS are appropriate for a senior-level mechanical
engineering student [12]. Quadrotors are associated with two major design challenges: (1)
they are inherently unstable, requiring the use of a control system; and (2) they have fewer
outputs than system states. For these reasons, a safe indoor test platform is needed to test and
tune the vehicle prior to free flight. Test platforms range in complexity from simple single-
axis test stands [13] to gravity balanced, five degree-of-freedom test stands [14]. These test
platforms provide the necessary equipment to perform a variety of experiments on a
multirotor system including experimental gain tuning (using methods such as Zeigler-
Nichols), parameter estimation, and full six degree-of-freedom hardware-in-the-loop
simulations.
2. PLAN OF WORK
3
The primary student-developed course task is to develop, tune, and test an autonomous
quadcopter aerial vehicle capable of maintaining stable flight. In meeting this course task,
students will meet the four course-specific goals.
To meet the specific course goals, a broad course outline has been developed (Table 1).
Throughout the course, students will learn about current mechatronic systems (Course Goal
#4), as the autopilot system they will be using is an Arduino-based microcontroller with the
full attitude realization capabilities via an onboard Inertial Measurement Unit (IMU). To
fully utilize the onboard sensors (accelerometer, gyro, magnetometer, and barometric
pressure transducer), students will conduct experiments to quantify sensor uncertainty,
sampling speed, and calibrate sensors for both quadrotor and test stand instrumentation
(Course Goal #1). In addition to applying instrumentation curriculum material, students will
be applying theory from the Feedback Control Systems course to design a sophisticated
multi-input multi-output control system (Course Goal #2). Students will need to first design
and simulate their controllers and, using the information gathered, design and experimentally
tune the autopilot controller on the quadcopter (Course Goal #3).
The course will contain both lecture and lab components. A tentative course outline is shown
in Table 2 with specific course goals covered in each subject topic shown in brackets. A
tentative course syllabus is provided in the supplemental documents section of this proposal.
Primary deliverables from Project Objective #1 will include results from (both summative
and formative) assessment instruments administered throughout the three-course sequence
indicating how well course objectives are being met.
4
Components of an Model verification MIMO control Flight testing
autopilot [1,2,3,4] techniques [2,3,4] design for attitude considerations/safety
stability [3,4] [1,2,3,4]
Interfacing with Interfacing with Model/simulation Flight testing in the
embedded actuators [1,4] gain tuning motion capture
systems/sensors [1,4] techniques [2] laboratory [1,2,3,4]
Wireless & wired Experimental system Experimental gain Dissemination of
communication [1,4] identification tuning techniques results [1,2,4]
techniques [1,2,4] [1,2,3,4]
2.2. Project Objective #2: Evaluate and prescribe infrastructure for reproducing
course content at other institutions
Prior to conducting the quadrotor-based mechatronics course, several key infrastructure
components must be developed and tested including a vehicle test platform, hardware-in-the-
loop simulation software, and the software platform on which students will develop their
autopilot systems. Once the infrastructure needs have been adequately tested and validated,
the project software can be downloaded from the course website and off-the-shelf
components can be purchased from identified retailers such that the course can be easily
adopted at other institutions. The specific outcomes for the infrastructure development phase
of the proposed work are:
1. Develop, test, and compare high and low cost quadcopter experimental platforms
(software and hardware)
2. Quantify vehicle geometric envelope for use on experimental platforms
3. Create a vehicle software foundation enabling rapid student-created software
5
see the results of that tuning first-hand, using standard techniques such as the Zeigler-Nichols
method.
The first test stand utilizes a relatively inexpensive two-axis load cell and spherical joint.
The two-axis load cell provides the vehicle thrust and torque about the vertical axis. In
conjunction with the vehicle attitude derived from onboard sensors, the HIL simulation can
be performed with the two-axis load cell platform as well as stability testing, attitude control
testing, and gain tuning. The major limitation of the two-axis test platform configuration is
the requirement for the two-axis load cell to be mounted on top of the spherical joint. This
greatly changes the rotational axis of the vehicle when compared to the free-flight scenario.
However, it is anticipated that relatively simple vehicle modifications (such as mounting
motors on the lower side of the aircraft frame) can adequately overcome this limitation.
Each student enrolled in the course will perform a series of simulation tests on each of the
two test stands, in order to develop a comprehensive set of experimentally- and simulation-
derived gains for each configuration (two test stands x two gain configurations = four trials
total). Vehicles will then be flown in the HML under each of the four gain configurations,
during which desired and actual trajectories will be captured and saved for later analysis
(described below).
6
The onboard Arduino-based microcontroller incorporates all of the necessary sensors for use
as an unmanned vehicle autopilot, and fortunately, many hobbyists have teamed together to
create an open-source autopilot software. Using the open-source autopilot as a starting point,
a student development software can be easily created which handles many of the
infrastructure-type requirements of an autopilot (such as sensor communication, remote
control receiver communication, loop speed handling, etc.). The resulting software package
will simply be a skeleton structure for students to incorporate their command and control
routines, without the need for developing the software completely on their own.
3. BROADER IMPACTS
In addition to these public outreach efforts, we will take advantage of existing infrastructure
(described below) within the School of Computing & Engineering (SCE) to promote STEM
7
awareness and education among high school and middle school students in the Kansas City
area. Specifically, we will host four open house events, during which area Project Lead the
Way (PLTW) students will tour the SCE laboratories involved in the proposed work. During
the first visit each year (March 2016/2017), selected students enrolled in the course will
introduce PLTW attendees to instrumentation and control theory via short hands-on activities,
as well as report on their quadrotor design progress. During the second visit each year (May
2016/2017), the same group of SCE students will perform flight testing of their completed
designs for PLTW attendees.
8
Student learning closely couples with student interest and motivation in a particular topic [6];
therefore, motivation to pursue engineering careers will be assessed along with retention of
knowledge about instrumentation and feedback controls material.
The specific outcomes of Project Objective #1 are expressed in standard deviations, and thus
represent moderate effect sizes (i.e., Cohens d = 0.50). Given a moderate effect size, and
significance level of .05, and three (or four, if comparing the 2016 and 2017 offerings of the
proposed course) groups measured on three occasions, 28-33 students would be needed in
each group (98-113 total) to achieve a statistical power of .80.
9
beginning and end of the course for purposes of project evaluation only. Only data from those
students who have gone through an IRB-approved consent process will be used for research
purposes, and only such students will be asked to complete the measures one year after the
course.
For students in the courses, class time will be set aside for completion of the measures at the
beginning and end of the courses. For students in neither course, the measures will be
administered in a group setting in January 2016 and again in May 2016. Several times will be
offered in each month to maximize recruitment. All students will be contacted via email,
phone, or mail one year later and invited to complete the measures a third time in a group
setting. Again, several times will be offered to maximize retention of participants.
Administration of the test of knowledge in a group setting is necessary in order to prevent
some participants from using outside resources to answer questions.
Project Evaluation.
Summative assessment will take the form of results from the data analysis detailed above at
the end of the project in May 2018. Formative assessment will also take the form of the same
data analysis, but at the end of the first proposed course, in May 2016, in order to determine
if adjustments need to be made to the course for the 2017 offering. In addition to this
progress evaluation, an implementation evaluation will be conducted to ensure fidelity to
project objectives.
10
has a frame span of 45cm with a mass of 500g. During the testing phase of this study,
additional airframe sizes may be tested to provide a reasonable envelope that can be used
without on-site validation at other institutions.
Professional Dissemination.
The investigators will rely on existing mechanisms to gain feedback on professional
dissemination of the proposed work. This is expected to include peer reviews from journal
11
and conference paper submissions, face-to-face interactions at conferences and seminars, and
citation statistics such as those generated via Google Scholar and ResearchGate.
5. EXISTING RESOURCES
5.1 Infrastructure
The prerequisite courses serving as the basis for the pilot course developed in this project are
already part of the existing curriculum within UMKCs Mechanical Engineering program.
ME352 Instrumentation and Measurements Lab focuses on measurement theory,
mechanical engineering instrumentation, and experimentation methods. The course features a
lecture portion (taught by 1 full-time faculty member) and a mandatory lab portion (taught by
2 teaching assistants and overseen by the faculty member). ME415 Feedback Control
Systems is focused on control theory for linear dynamic systems, and covers root locus
analysis, frequency response analysis, and introductory controller design. This course also
features several hand-on demonstrations to illustrate lecture concepts.
All laboratory resources needed to complete the proposed work are already in existence at
UMKC. These include: (1) the Instrumentation Laboratory (room 335 Flarsheim Hall),
featuring sensors and data acquisition equipment for measuring voltage, current, resistance,
force, strain, temperature, flow, and pressure (Figure 3 right); the Parachute and Aerial
Vehicle Systems Laboratory (room 334 Flarsheim Hall), featuring embedded systems and
Figure 3: Human Motion Lab (left) and Instruments and Measurements Lab (Right)
sensors, three cargo-carrying multirotors, and aerial vehicle assembly tools; and (3) the
Human Motion Laboratory (room 319 Flarsheim Hall), a fully-equipped gait lab featuring
motion capture cameras to be used for position measurement during testing (Figure 3 left).
12
students in the greater Kansas City area. The KC STEM Alliance coordinates the areas
Project Lead the Way (PLTW) and FIRST robotics programs and also serves as a central hub
for facilitating connections between schools and industry. Through the KC STEM Alliance,
the investigators will have access to nearly 20,000 students in 183 area schools with an
interest in STEM. The investigators will work closely with the KCSTEM director (also the
dean of the UMKC School of Computing and Engineering), and his letter of support for this
study is located in the supplemental documents of this proposal.
120
100
60
40
2000
0
-2000
0 10 20 30 40 50 60
Y Position [mm]
2000
0
-2000
0 10 20 30 40 50 60
Z Position [mm]
2000
0
-2000
0 10 20 30 40 50 60
Time [sec]
Figure 5: Post-processed position data from preliminary quadrotor
flight testing in HML.
13
system identification (as the hardware provides only thrust measurements) as shown in
Figure 4 right. The investigators have performed preliminary tests of the motion capture
equipment in UMKCs Human Motion Laboratory to establish feasibility of accurately
tracking quadrotor position with the existing laboratory resources. Figure 5 depicts 3D
position data, in the laboratory reference frame, of a tracking marker placed on a quadrotor
while operating under remote control during a 60-second flight test.
Dr. Jacob Marszalek will serve as a Co-Principal Investigator and has a background in
Educational Psychology and expertise in statistics and research design, including multilevel
modeling, with research interests in educational and psychological assessment, quantitative
methodology, motivation, and evaluation of STEM programs for women and minorities. Dr.
Marszalek will be responsible for assessing outcomes for Project Objective #1, including data
collection and analysis, and will assist in assessment of student achievement in the course.
The University has a plan in place to provide appropriate training and oversight in the
responsible and ethical conduct of research to undergraduates, graduate students and
postdoctoral researchers who will be supported by NSF to conduct research.
Since the proposed work builds on infrastructure and curriculum already in place at UMKC,
the probability of success is very high. However, the investigators have identified several
components of the proposed work that could potentially impact the other activities if not
completed successfully. Contingency plans for these possible conflicts are summarized below
in Table 4.
14
Student engineering self- Revise hands-on laboratory activities to
efficacy does not increasebe more interactive to students, and tie
sufficiently. lecture content into real-world context.
Six-axis load cell platform is
Attempt to source lower cost six-axis
Project
only viable option to
platform components to reduce other
Objective #2
accurately simulate motion.
institutional acquisition costs and validate.
Include on-board wall detection and
Problems with HML real-
utilize motion tracking for post-processing
time position feedback.
evaluation.
7. SUSTAINABILITY
Funds requested for the proposed work will primarily be used for initial infrastructure and
curriculum development. It is expected that, once implemented, remaining costs associated
with the proposed work will primarily be related to hardware and software upgrades. These
expenses will be covered via existing mechanisms, including departmental funds specifically
dedicated to laboratory upgrades. The quadrotor hardware to be used by the students during
future course offerings will be funded directly from individual students fees.
8. UNIVERSITY SUPPORT
To date, the UMKC School of Computing and Engineering has invested over $20,000 in
computers, embedded sensors and supplies, and a single six-axis load cell. Additionally, the
UMKC Mechanical Engineering faculty has shown support for the new three-course
curriculum with the recent unanimous decision to implement the mechatronics course as a
mandatory course.
9. RESULTS FROM PRIOR NSF SUPPORT
The Co-PI (King) was a co-investigator on an NSF Major Research Instrumentation grant,
MRI: Acquisition of an Experimental Platform to Support Research and Educational
Activities in Human Motion (CBET-0821459; Trent M. Guess, PI).
15
REFERENCES
[1] Shiller, Z., A Bottom-Up Approach to Teaching Robotics and Mechatronics to
Mechanical Engineers, IEEE Transactions on Education, Vol. 56, No.1,
February 2013
[2] Gardner, F., The Role of Mechanical Design in Mechatronics Education,
IEEE/ASME International Conference on Advanced Intelligent Mechatronics,
July 8-12, 2001, Como, Italy
[3] Craig, K., and Voglewede, P., Multidisciplinary engineering systems in
graduate education: Master of engineering in mechatronics, Proc. IEEE
Transforming Engineering Education, Creating Interdisciplinary Skills Complex
Global Environment, pp. 1-14, 2010
[4] Felder, R. M., and Silverman, L. K., "Learning and teaching styles in
engineering education." Engineering education, 78, No. 7, 674-681 (1988)
[5] Mills, Julie E., and David F. Treagust, "Engineering educationIs problem-
based or project-based learning the answer?." Australasian Journal of
Engineering Education, 3, 2-16 (2003)
[6] Dutson, A. J., Todd, R. H., Magleby, S. P., and Sorensen, C. D. "A Review of
Literature on Teaching Engineering Design Through ProjectOriented Capstone
Courses." Journal of Engineering Education, 86, No. 1, 17-28 (1997)
[7] Craig, K., Is anything really new in mechatronics education?, IEEE Robotics
Automation Magazine, Vol. 8, No. 2, pp. 12-19, June 2001
[8] Meek, S., Field, S., and Devasia, S., Mechatronics education in the Department
of Mechanical Engineering at the University of Utah. Mechatronics, 13, 1-11
(2003)
[9] Tobias, S., Interest, Prior Knowledge, and Learning, Review of Educational
Research, Vol. 64, No. 1, pp. 37-54, Spring 1994
[10] Zolfagharifard, E., How Lady Gagas Flying Dress Works, MailOnline,
Published November 12, 2013 <http://www.dailymail.co.uk/sciencetech/article-
2499954/How-Lady-Gagas-flying-dress-works.html>
[11] Fact Sheet FAA UAS Test Site Program, Federal Aviation Administration,
Published December 30, 2013 <www.faa.gov>.
[12] Gaponov, I., and Razinkova, A., Quadcopter design and implementation as a
multidisciplinary engineering course, 2012 IEEE International Conference on
Teaching, Assessment, and Learning for Engineering (TALE), August 20-23,
2012, Hong Kong
[13] Davis, E., Nizette, B.E., and Yu, C., Development of a Low Cost Quadrotor
Platform for Swarm Experiments. Proc. Of 32nd Chinese Control Conference,
July 26-28, 2013, Xian, China
[14] Hanford, S.D., Long, L.N., and Horn, J.F., A small semi-autonomous rotary-
wing unmanned air vehicle (UAV). Proc. Of AIAA Infotech@Aerospace
Conference, Washington, D.C., 2005
[15] Yu, Y. and Ding, X., A Quadrotor Test Bench for Six Degree of Freedom
Flight. Journal of Intelligent Robotic Systems, 68, 323-338 (2012)
[16] Huntoon JE and Lane MJ, Diversity in the geosciences and successful strategies
for increasing diversity, Journal of Geoscience Education 55:447-457, 2007.
[17] Perna LW, Precollege outreach programs: characteristics of programs serving
historically underrepresented groups of students, Journal of College Student
Development 43(1):64-83, 2002.
[18] Poock MC, A shifting paradigm in the recruitment and retention of
underrepresented graduate students, Journal of College Student Retention
9(2):169-181, 2007.
Travis Fields
Assistant Professor
Department of Civil and Mechanical Engineering
Flarsheim Hall 352
University of Missouri, Kansas City Phone: (816) 235-1291
Kansas City, MO 64110 e-mail: fieldstd@umkc.edu
a. Professional Preparation
University of Nevada, Reno Mechanical Engineering B.S., 2008
University of Nevada, Reno Mechanical Engineering M.S., 2009
University of Nevada, Reno Mechanical Engineering Ph.D., 2013
b. Appointments
2013 Present: Assistant Professor, University of Missouri, Kansas City, MO
2010 2013: Doctoral Researcher, University of Nevada, Reno, NV
2008 2010: Graduate Research Assistant, University of Nevada, Reno, NV
2008 2012: Graduate Teaching Assistant, University of Nevada, Reno, NV
c. Products
Fields, T.D., Development and Feasibility of a Non-Invasive, Wireless Parachute Load
Distribution Measuring System, AIAA Aviation Forum, Atlanta, GA, June 16-20, 2014.
Fields, T.D., Yakimenko, O.A., LaCombe, J.C., and Wang, E.L., Lower Stratospheric
Deployment Testing of a Ram-Air Parafoil System, AIAA Science and Technology
Forum and Exposition, National Harbor, MD, January 13-17, 2014.
Fields, T.D., LaCombe, J.C., and Wang, E.L., Autonomous Guidance of a Circular Parachute
Using Descent Rate Control, Journal of Guidance, Control, and Dynamics, Vol. 35, No.
4, 2012, pp. 1367-1370.
Fields, T.D., LaCombe, J.C., and Wang, E.L., Path Planning of a Circular Parachute Using
Descent Rate Control, 22nd AIAA Aerodynamic Decelerator Systems Technology
Conference and Seminar, Daytona Beach, FL, March 25-28, 2013.
Fields, T.D., LaCombe, J.C., and Wang, E.L., Flight Testing of a 1-DOF Variable Drag
Autonomous Descent Vehicle, 22nd AIAA Aerodynamic Decelerator Systems
Technology Conference and Seminar, Daytona Beach, FL, March 25-28, 2013.
Smith, A.J., Fields, T.D., LaCombe, J.C., and Wang, E.L., Development of a Coupled
Dropsonde-Autonomous Descent Vehicle System, 22nd AIAA Aerodynamic Decelerator
Systems Technology Conference and Seminar, Daytona Beach, FL, March 25-28, 2013.
d. Synergistic Activities
NSF-GK12 fellow from August 2012 July 2013 in which I was immersed in skills
necessary for success in an academic related career. Also spent a minimum of 10 hours
per week in an environmental science classroom incorporating engineering into the
curriculum.
Technical committee member for AIAA Atmospheric Flight Mechanics May 2014 May
2017.
Developed an upper division/graduate rigid body dynamics course that exposes students
to general rigid body kinematics and kinetics with Kanes method.
a. Professional Preparation
University of Kansas Mechanical Engineering B.S., 1999
University of Kansas Mechanical Engineering M.S., 2002
University of Kansas Mechanical Engineering Ph.D., 2006
b. Appointments
2007 Present Assistant Professor of Mechanical Engineering, University of Missouri
Kansas City, Kansas City, MO
2006 2007 Postdoctoral Fellow, Landon Center on Aging, University of Kansas
Medical Center, Kansas City, KS
2003 2006 Graduate Research Assistant, Department of Mechanical Engineering,
University of Kansas, Lawrence, KS
2000 2002 Graduate Teaching Assistant, Department of Mechanical Engineering,
University of Kansas, Lawrence, KS
c. Products
5 most relevant products
1. Mullin DS, King GW, Saripalle SK, Derakhshani RR, Lovelace CT, Burgoon JK,
Deception Effects on Standing Center of Pressure, Human Movement Science 38:106-115,
2014.
2. Saripalle SK, Paiva GC, Cliett TC, Derakhshani RR, King GW, Lovelace CT,
Classification of Body Movements Based on Posturographic Data, Human Movement
Science 33:238-250, 2014.
3. Shirey M, Hurlbutt M, Johansen N, King GW, Wilkinson SG, Hoover DL, The Influence of
Core Musculature Engagement on Hip and Knee Kinematics in Women During a Single Leg
Squat, The International Journal of Sports Physical Therapy 7(1):1-12, 2012.
4. Shirey M, Hurlbutt M, Johansen N, Wilkinson SG, King GW, Hoover DL, Influence of
Core Musculature Engagement on Knee Kinematics of Females During a Single Leg Squat,
Medicine and Science in Sports and Exercise 43:501, 2011.
5. Guess TM, Derakhshani RR, King GW, Leon-Salas WD, Multi-Disciplinary Collaborations
in Measurement of Human Motion, Missouri Regional Life Sciences Summit, Kansas City,
MO, 2010.
5 other products
1. King GW, Bruetsch AP, Kevern JT, Slip-Related Characterization of Gait Kinetics:
Investigation of Pervious Concrete as a Slip-Resistant Walking Surface, Safety Science
57:52-59, 2013.
2. Kevern FT, King GW, Bruetsch AP, Pervious Concrete Surface Characterization to Reduce
Slip-Related Falls, Journal of Performance of Constructed Facilities 26(4):526-531, 2012.
3. King GW, Akula CK, Luchies CW, Age-Related Differences in Kinetics Measures of
Landing Phase Lateral Stability During a Balance-Restoring Forward Step, Gait and
Posture 35(3):440-445, 2012.
4. King GW, Stylianou AP, Kluding PM, Jernigan SD, Luchies CW, Effects of Age and
Localized Muscle Fatigue on Ankle Plantar Flexor Torque Development, Journal of
Geriatric Physical Therapy 35(1):8-14, 2012.
5. Bruetsch AP, King GW, Kevern JT, Biomechanical Characterization of Slipping on
Pervious and Traditional Concrete Walking Surfaces, 35th Annual Meeting of the American
Society of Biomechanics, Long Beach, CA, 2011.
d. Synergistic Activities
1. Faculty advisor for UMKCs Missouri Phi Eta Chapter of Pi Tau Sigma Mechanical
Engineering Honor Society
2. Developed introductory and advanced level biomechanics courses at UMKC that expose
students to analysis and interpretation of kinematic, kinetic, and electromyographic data
associated with human motion
3. Member of UMKCs multidisciplinary Adopt a School committee, designed to increase
awareness and interest in STEM among Kansas City area high school students
4. Member of an interdisciplinary team of researchers on an NSF Major Research
Instrumentation grant providing infrastructure for experimental research in human motion;
enriching current and future bioengineering courses, and attracting prospective students from
the Universitys urban community, including those from underrepresented groups.
5. Faculty participant in Science Power, a program exposing urban high school students to
hands-on activities designed to generate interest in STEM fields; funded by a United Services
Community Action Agency grant awarded to UMKCs Division of Diversity, Access, and
Equity
E-1
American Educational Research Association.
Consultations for educational program evaluations at the University of Illinois at Urbana-
Champaign, College of Engineering, and the University of Missouri-Kansas City.
Collaborations and Other Affiliations
i) Collaborators
Carolyn Barber University of Missouri-Kansas City
Clare Bell University of Missouri-Kansas City
LaVerne Berkel University of Missouri-Kansas City
Debra Bragg University of Illinois at Urbana-Champaign
Baek-Young Choi University of Missouri-Kansas City
Christopher Culbertson Kansas State University
Deendayal Dinakarpandian University of Missouri-Kansas City
Michelle Foster University of Missouri-Kansas City
Kathy Fuger University of Missouri-Kansas City
Alan Glaros KC University of Medicine and Bioscience
George Gotto IV University of Missouri-Kansas City
Ronda Jenson University of Missouri-Kansas City
John Kevern University of Missouri-Kansas City
Gregory King University of Missouri-Kansas City
Michael Kruger University of Missouri-Kansas City
Yugyung Lee University of Missouri-Kansas City
Jane Loeb University of Illinois at Urbana-Champaign
Tamera Murdock University of Missouri-Kansas City
Deborah OBannon University of Missouri-Kansas City
A. Louis Odom University of Missouri-Kansas City
Praveen Rao University of Missouri-Kansas City
Sanjay Rebello Kansas State University
Jovanna Rohls University of Missouri-Kansas City
Elizabeth Stoddard University of Missouri-Kansas City
Kevin Truman University of Missouri-Kansas City
Bruce Wellman Olathe (KS) School District
ii) Graduate and Postdoctoral Advisors
M.S. Advisor: Baker, K. (Emporia State University, Emporia, KS)
Ph.D. Advisor: Loeb, J. (University of Illinois at Urbana-Champaign, Urbana, IL),
Dissertation Chair: Roussos, L. (University of Illinois at Urbana-Champaign, Urbana, IL)
iii) Thesis advisor and Postgraduate Scholar Sponsor
Grotewiel, M. (University of Missouri-Kansas City)
Hager, P. (University of Missouri-Kansas City)
Kirkpatrick-Smiley, R. (University of Missouri-Kansas City)
Kohlhart, J. (University of Missouri-Kansas City)
E-2
SUMMARY YEAR 1
PROPOSAL BUDGET FOR NSF USE ONLY
ORGANIZATION PROPOSAL NO. DURATION (months)
University of Missouri-Kansas City Proposed Granted
PRINCIPAL INVESTIGATOR / PROJECT DIRECTOR AWARD NO.
Travis Fields
NSF Funded Funds Funds
A. SENIOR PERSONNEL: PI/PD, Co-PIs, Faculty and Other Senior Associates Person-months Requested By granted by NSF
(List each separately with title, A.7. show number in brackets) CAL ACAD SUMR proposer (if different)
Lawrence dreyfus
1 *ELECTRONIC SIGNATURES REQUIRED FOR REVISED BUDGET
SUMMARY YEAR 2
PROPOSAL BUDGET FOR NSF USE ONLY
ORGANIZATION PROPOSAL NO. DURATION (months)
University of Missouri-Kansas City Proposed Granted
PRINCIPAL INVESTIGATOR / PROJECT DIRECTOR AWARD NO.
Travis Fields
NSF Funded Funds Funds
A. SENIOR PERSONNEL: PI/PD, Co-PIs, Faculty and Other Senior Associates Person-months Requested By granted by NSF
(List each separately with title, A.7. show number in brackets) CAL ACAD SUMR proposer (if different)
TOTAL EQUIPMENT 0
E. TRAVEL 1. DOMESTIC (INCL. CANADA, MEXICO AND U.S. POSSESSIONS) 5,000
2. FOREIGN 0
Lawrence dreyfus
2 *ELECTRONIC SIGNATURES REQUIRED FOR REVISED BUDGET
SUMMARY Cumulative
PROPOSAL BUDGET FOR NSF USE ONLY
ORGANIZATION PROPOSAL NO. DURATION (months)
University of Missouri-Kansas City Proposed Granted
PRINCIPAL INVESTIGATOR / PROJECT DIRECTOR AWARD NO.
Travis Fields
NSF Funded Funds Funds
A. SENIOR PERSONNEL: PI/PD, Co-PIs, Faculty and Other Senior Associates Person-months Requested By granted by NSF
(List each separately with title, A.7. show number in brackets) CAL ACAD SUMR proposer (if different)
Lawrence dreyfus
C *ELECTRONIC SIGNATURES REQUIRED FOR REVISED BUDGET
BUDGET JUSTIFICATION
Personnel:
The budget requests funds for one months salary per year for the PI (Fields) and Co-PI
(King) for development and testing of the course infrastructure. One month of salary per
year is requested for the Co-PI (Marszalek) for assessment creation, administration, and
analysis. The budget provides funding for a graduate research assistant ($18,000/year)
and one undergraduate research assistant ($6,000 and $3,000 for year one and two,
respectively) who will assist with designing, constructing, and testing all necessary
course infrastructure (including test stands, motion capture lab setup, and quadrotor test
vehicles). Fringe is charged at 36% of the PI and Co-PI salaries, and 4% for the student
salaries.
Equipment:
One Bertec six-axis load cell is requested ($7,298) for use in constructing a 6-DOF
hardware-in-the-loop test stand. All reaction forces and moments are necessary to
simulate the rotational and translational motion with the no data necessary from the
aircraft itself (only reaction forces and moments).
An Edgertronic camera is requested ($5,545) for use in filming platform testing as well as
free flight testing. The Edgertronic camera is capable of recording at speeds up to 18,000
fps, and up to 700 fps while maintaining 720p HD. This camera is particularly useful in
monitoring the high rotational speeds of the quadcopter rotors, and is capable of
capturing significant qualitative flow data around the vehicle.
Travel:
A total of $4,000/year is requested for the investigators to travel to professional
conferences to present the findings from the proposed project to the engineering
education community. Funding is also requested ($1,000/year) for travel to the annual
NSF meeting for NSF-funded PIs in Washington, D.C.
Participant Support:
Funding is requested to provide study participants with incentives ($20 per person,
$1,120 total/year) in an effort to yield sufficient participant numbers particularly during
the one-year post-course assessment.
Materials and Supplies:
A total of $13,200 is requested for six dual-axis load cells (thrust and Z-moment) for use
in attitude controller tuning and stability test stands. To complete the seven (six-axis + 6
two-axis stands) total test stands, $2,400 is requested for materials and supplies (socket
joint, tripod, mounting bracket, etc.). A total of $4,230 ($2,980 for year one, $1,250 for
year two) is requested for miscellaneous course infrastructure items including battery
chargers, Lithium Polymer batteries (for use during development), construction materials,
2.4 GHz remote control transmitter/receiver units, and electrical materials. A total of
$1,000 is requested for safety netting in the Human Motion Laboratory. The netting
provides a barrier between observers and the aerial vehicles during testing. For
curriculum development and hardware testing, $2,250 is requested for quadrotor parts
and materials ($1,250 for year one, $1,000 for year two). The development quadrotors
will provide the platform for determining size/weight feasibility and verifying test stand
feasibility prior to course offering. A total of $1,720 is requested for development and
production of several single-axis rotation devices and motor/propeller tachometer devices.
These devices are used in the early stages of the quadrotor development process. $200 is
requested per year for publication and printing costs of the assessment materials.
Other Miscellaneous Expenses:
Resident tuition equivalent to six (6) credit hours per semester, per graduate student, is
included as other expenses and is a key component to recruiting qualified masters or
PhD students to this project. It is expected that Resident tuition will be $350 per credit
hour beginning June 2015.
Facilities & Administration (F&A):
The applicable indirect cost rate negotiated by the University of Missouri-Kansas City
with the cognizant negotiating agency is 51% for on-campus research activities. This rate
has been applied to the Modified Total Direct Costs in the proposal budget. Cognizant
Agency: Department of Health and Human Services. Agreement date: 03/17/2014.
Miscellaneous:
A 2% annual inflation increase has been added for salaries, benefits, and tuition for year
two project activities.
The University has a plan in place to provide appropriate training and oversight in the
responsible and ethical conduct of research to undergraduates, graduate students and
postdoctoral researchers who will be supported by NSF to conduct research.
Current and Pending Support
(See GPG Section II.C.2.h for guidance on information to include on this form.)
The following information should be provided for each investigator and other senior personnel. Failure to provide this information may delay consideration of this proposal.
Other agencies (including NSF) to which this proposal has been/will be submitted.
Investigator: Travis Fields
Support: Current Pending Submission Planned in Near Future *Transfer of Support
Project/Proposal Title: Autonomous Parachute and Aircraft Systems Development and
Hands-on Training
Source of Support:
Total Award Amount: $ Total Award Period Covered:
Location of Project:
Person-Months Per Year Committed to the Project. Cal: Acad: Summ:
*If this project has previously been funded by another agency, please list and furnish information for immediately preceding funding period.
Page G-1 USE ADDITIONAL SHEETS AS NECESSARY
Current and Pending Support
(See GPG Section II.C.2.h for guidance on information to include on this form.)
The following information should be provided for each investigator and other senior personnel. Failure to provide this information may delay consideration of this proposal.
Other agencies (including NSF) to which this proposal has been/will be submitted.
Investigator: Gregory King
Support: Current Pending Submission Planned in Near Future *Transfer of Support
Project/Proposal Title: Informatic and Architectural Analysis of Human Performance
in a Clinical Simulation Setting
Source of Support:
Total Award Amount: $ Total Award Period Covered:
Location of Project:
Person-Months Per Year Committed to the Project. Cal: Acad: Sumr:
Source of Support:
Total Award Amount: $ Total Award Period Covered:
Location of Project:
Person-Months Per Year Committed to the Project. Cal: Acad: Sumr:
Source of Support:
Total Award Amount: $ Total Award Period Covered:
Location of Project:
Person-Months Per Year Committed to the Project. Cal: Acad: Summ:
*If this project has previously been funded by another agency, please list and furnish information for immediately preceding funding period.
Page G-2 USE ADDITIONAL SHEETS AS NECESSARY
Current and Pending Support
(See GPG Section II.C.2.h for guidance on information to include on this form.)
The following information should be provided for each investigator and other senior personnel. Failure to provide this information may delay consideration of this proposal.
Other agencies (including NSF) to which this proposal has been/will be submitted.
Investigator: Jacob Marszalek
Support: Current Pending Submission Planned in Near Future *Transfer of Support
Project/Proposal Title: A Quadrotor-based Mechatronics Design Course for Improved
Information Retention
Source of Support:
Total Award Amount: $ Total Award Period Covered:
Location of Project:
Person-Months Per Year Committed to the Project. Cal: Acad: Sumr:
Source of Support:
Total Award Amount: $ Total Award Period Covered:
Location of Project:
Person-Months Per Year Committed to the Project. Cal: Acad: Sumr:
Source of Support:
Total Award Amount: $ Total Award Period Covered:
Location of Project:
Person-Months Per Year Committed to the Project. Cal: Acad: Summ:
*If this project has previously been funded by another agency, please list and furnish information for immediately preceding funding period.
Page G-3 USE ADDITIONAL SHEETS AS NECESSARY
FACILITIES, EQUIPMENT, AND OTHER RESOURCES
Laboratory: The Instrumentation and Measurements Laboratory (IML), directed by the
PI, is a 729 square foot facility in Flarsheim Hall on UMKCs Volker Campus. The IML
is dedicated to teaching, primarily through hands-on activities. The majority of student
participation in designing, building, and testing the aerial vehicle will be conducted
within the IML.
The Parachute and Aerial Vehicle Systems (PaAVS) Laboratory, directed by the PI, is a
250 square foot facility housed next door to the IML in Flarsheim Hall. The PaAVS
laboratory supports research related to design and development of improved autonomous
parachute systems and unmanned aerial vehicles.
The Human Motion Laboratory (HML), directed by the Co-PI (King), is a 500 square
foot facility located in Flarsheim Hall. The HML is currently dedicated to
musculoskeletal experimentation research, and will provide the free flight indoor testing
facility.
Computer: The IML features nine Dell Optiplex PCs with 2.90 GHz Intel Core i5 quad
core processors. The PaAVS laboratory contains two Dell Optiplex PCs with 2.90 GHz
quad core processors. The PIs office features an Apple Macbook Pro with a 2.4 GHz
Intel i7 quad core processor with 16 Gb of RAM. Co-PI Kings office features a Dell
Optiplex 980 PC with an Intel Core i5 processor. Co-PI Marszaleks office contains a
Dell Optilplex 980 PC with an Intel Core i5 processor and 8 GB of RAM. The HML
contains a VICON computer workstation with an Intel Core 2 quad processor.
Office: The IML provides undergraduate students with the necessary space to perform
nearly all development and testing for the proposed course. The PIs office, located on
the same floor in Flarsheim Hall as the IML, PaAVS laboratory, and the HML, features
130 square feet of space and a PC (described above) dedicated to research and teaching.
Similarly, Co-PI Kings office, also located on the same floor, features 130 square feet
and a PC dedicated to both research and teaching. Co-PI Marszalek has an office in the
Education Building that is 130 square feet and a PC dedicated to both research and
teaching.
Major Equipment: The HML is a fully equipped gait lab used for biomechanical testing,
and includes a Vicon motion capture system equipped with 7 MX-T40 cameras, a Basler
GigE digital reference video camera; and four AMTI OR6-6 force platforms with MSA-6
amplifiers.
The UMKC Civil and Mechanical engineering department recently invested
approximately $20,000 in the IML by acquiring additional student computers, Arduino
programming platforms, embedded sensors and actuators, and a single BERTEC six-axis
load cell with amplifier.
Other Resources: In addition to the resources and personnel listed above, the outreach
and educational aspects of the proposed work involve several supports, including Dr.
Kevin Truman (Dean, UMKC School of Computing and Engineering); Dr. Mark
McClernon (Chair, Department of Civil and Mechanical Engineering); and Ms. Laura
Loyacono (Director, KC STEM Alliance).
One full time machinist, full time technician, two full time administrative personnel, and
fully-equipped machine and electronics shops (located in Flarsheim Hall) are available
for the duration of the project.
DATA MANAGEMENT PLAN
Expected Data
All course related material will be stored on the course Blackboard website during the
semester in which the material was taught. Upon course completion, all material will be
transferred to a university supported, publically accessible website, where it will remain
indefinitely. The website will contain all files needed for developing a clone course at
another institution, including (but not limited to) quadrotor sample code, test stand design
and validation procedure, instructions for performing the various simulated and
experimental tests, and procedures for conducting safe flight testing operations.
Period of Data Retention
As the course will be taught once per year, the website will be periodically updated to
reflect the most recent course offering. Website material will be hosted indefinitely on
the UMKC PIs webpage.
Data Formats and Dissemination
To ensure student privacy, only the vehicles themselves will be hosted on the course
webpage. All other materials to be distributed are direct products of the investigator team,
and as such, are freely distributed in the public domain. For educational outcomes
tracking, students will be given unique anonymous identification numbers, in order to
permit tracking of particular student progress throughout the three-course sequence. All
electronic data will be stored on password-protected computers by the investigator team
only.
Dissemination will be conducted through usual domains such as professional conferences
(specifically American Society of Engineering Education, American Educational
Research Association, American Society of Mechanical Engineering, and American
Institute of Aeronautics and Astronautics), professional journals (Journal of Engineering
Education, Journal of Research in Science Teaching, Science Education, and Journal of
Aerospace Sciences), science and engineering magazines (Nuts & Volts, Servo Magazine,
and Make Magazine), and electronics retailers such as SparkFun.com. Dissemination
will ultimately refer the interested party to the UMKC hosted webpage, as the website
will contain the most up-to-date information, as well as videos and pictures.
Data Storage and Preservation of Access
All data will be stored electronically on password-protected computers (controlled by the
investigator team only). None of the data collected specifically for the proposed course
development will contain individually identifiable private information. Participant names
will only be used to determine the unique identification number, enabling tracking of
individual students throughout the course sequence. Dr. Fields, Dr. King, and Dr.
Marszalek will routinely perform independent data backup.
MENTORING PLAN
Not Applicable
Course Syllabus
Required Elective
Course Credit Contact
Information: Selective Elective Hours: 3 Hours: 45
Description: ME 457 is a course for Mechanical Engineering students that introduces the basic principles
of mechatronic applications through course instruction and hands-on activities and
projects. Students use a microcontroller coupled with many embedded sensors. Topics
covered include analog signal processing, microcontroller hardware and programming,
digital communication, analog to digital and digital to analog conversion, actuator control,
sensors, system identification, and applied feedback control. Each student will also conduct
and present a microcontroller-based project.
Prerequisites: ME 352 Instrumentation & Measurements Lab, ME 415 Feedback Control Systems
Co-Requisites:
Successors:
Supplemental Materials:
Course Objectives:
Instructional Outcomes: (1) Collect, analyze, and improve measurement data, (2) Design and evaluate
a multi-input multi-output feedback control system, (3) Compare simulated
and actual experimental data to identify control system parameters, (4)
Integrate and utilize measurements with physical hardware and software-
based embedded control algorithms to create active control system.
ABET c) an ability to design a system, component, or process to meet desired needs within realistic
Outcomes: constraints such as economic, environmental, social, political, ethical, health and safety,
manufacturability, and sustainability