Professional Documents
Culture Documents
Meritor UpdateTimkenBearings PDF
Meritor UpdateTimkenBearings PDF
Product Up UD-69
date
date
May 1999
TIMKEN Bearings
Registered Trademark
Table of Contents:
Page Page
Introduction ........................................................ 2 Bearing Identification Chart ............................. 13
Proper Wheel Bearing Adjustment .................... 3 By Cone Inside Diameter ......................... 13
Application Section ............................................ 4 By Cup Outside Diameter ........................ 24
Front Steering Axle .................................... 4 Tools ................................................................ 40
Rear Drive Axle .......................................... 6 Part Number Index .......................................... 42
Trailer Axle ............................................... 10
EUCLID INDUSTRIES, LLC 6660 BETA DRIVE CLEVELAND, OHIO 44143-2321 (440) 461-4300
EUCLID INDUSTRIES CANADA LTD. TORONTO EDMONTON MONTREAL VANCOUVER
The Euclid Timken Tapered Roller Bearing part numbering system has been designed with the counterperson
and maintenance personel in mind. All the numbers begin with the "E-" prefix designating Euclid, followed by
"TM" designating GENUINE TIMKEN TAPERED ROLLER BEARINGS, followed by the Timken part number.
Example:
E- TM HM212049
Prefix Timken
for Euclid Part Number
Designation
for Genuine
Timken Bearings
Cup
Cage
Roller
Cone Timken tapered roller bearings meet a wide range
of application requirements. The design combined with
quality material and precision machining gives you a
part with outstanding performance.
Timken offers a variety of cup and cone configura-
Cup Cone tions, single-row, two-row, four-row, and thrust bearing
OD ID assemblies. At this time Euclid is offering the single-
row configuration (TS type) as shown.
Bearing
Width
Cup
Rollers
Pre-lubricate the bearings with clean lubricant of the same type used in the hub assembly or axle sump.
Torque the adjusting nut (inner nut) to 200 ft. lbs. (271 N-m) to seat the bearing components while rotating or
oscillating the wheel assembly to assure that the rollers are fully seated against the cone large rib.
Back off the adjusting nut (inner nut) one full turn or until loose, rotating the wheel assembly.
End-play (free movement) can now be established. Torque the adjusting nut (inner nut) to 50-ft lbs. (68 N-m)
while rotating the wheel hub assembly.
Back off the adjusting nut (inner nut) the appropriate amount using the chart below for the exact amount.
CAUTION: Failure to back off the adjusting nut (inner nut) as shown in the
chart below could cause the bearing to run hot, damaging the bearing
assembly, hub, or spindle. If this happens during operation, the wheel
assembly could lock or come off causing damage to property and limb.
If a single nut system, be sure the lock system is in place (Cotter pin, etc.).
At this time, install the locking washer (dowel pin or tang style). If the washers, dowel pin or tangs do not align
remove the washer and turn it over, reinstalling it. If the pins or tangs still fail to align, loosen the adjusting nut
(inner nut) just enough for proper alignment.
CAUTION: Never tighten the adjusting nut (inner nut) at this point of the
procedure. It could pre-load the bearing causing it to "run hot" resulting in
premature failure.
Install jam nut (outer nut) and torque to proper specifications, depending on the nut size, using the chart below.
Verify end play with a dial indicator. The acceptable end-play (free movement) of the tire and wheel assembly
along the spindle axis is 0.001" to 0.005" (0.025 mm to 0.0127 mm).
Threads Final
Axle Type Nut Size Torque Specifications
Per Inch Back Off
12 1/6 Turn Install Cotter Pin to Lock
18 1/4 Turn Axle Nut in Position
Steer
(Front) 14 Less Than
Non-Drive 200-300 ft. lbs.
1/2 Turn 2 5/8"
(271-407 N-m)
18 (66.7 mm)
or
12 Dowel Type 300-400 ft. lbs.
Washer (407-542 N-m)
1/4 Turn
Drive
16 Tang Type 200-275 ft. lbs.
Washer (271-373 N-m)
12 2 5/8"
300-400 ft. lbs.
Trailer 1/4 Turn (66.7 mm
(407-542 N-m)
16 and over)
1 2 3 4
DANA / SPICER
AXLE CAPACITY OUTER CONE OUTER CUP INNER CUP INNER CONE
MODEL (1) (2) (3) (4)
I60 6,000 lbs.
I75 7,500 lbs. E-TM25877 E-TM25820 E-TMJM207010 E-TMJM207049A
I80 8,000 lbs.
I90 9,000 lbs.
E-TM28682 E-TM28622 E-TMHM212011 E-TMHM212049
I108 10,800 lbs.
E-TMSET407 E-TMSET413
E-TM3782 E-TM3720 E-TMHM212011 E-TMHM212049
E-TMSET406 E-TMSET413
I120 12,000 lbs.
E-TM28682 E-TM28622 E-TMH715311 E-TMH715345
E-TMSET407
I132
13,200 lbs. E-TM555-S E-TM552A E-TMH715311 E-TMH715345
1986 to present
E-TM3782 E-TM3720 E-TMHM212011 E-TMHM212049
I140 14,000 lbs.
E-TMSET406 E-TMSET413
EATON
AXLE CAPACITY OUTER CONE OUTER CUP INNER CUP INNER CONE
MODEL (1) (2) (3) (4)
1 2 3 4
MERITOR
AXLE CAPACITY OUTER CONE OUTER CUP INNER CUP INNER CONE
MODEL (1) (2) (3) (4)
Don't Forget!!
Euclid's quality line of remanufactured, not just rebuilt, products also
includes:
1 2 3 4
1 2 3 4
Don't Forget!!
Euclid offers a comprehensive Shock Absorber line to meet all
your Heavy, Medium and Light-Duty truck needs.
1 2 3 4
1 2 3 4
S.O.S.
Special Order Service
Can't find it? Trouble sourcing products? Need assistance?
S.O.S.
S.O.S.) help.
Let Euclid's Special Order Service (S.O.S.
Euclids position as the market leader provides you access to a comprehensive
array of truck parts products from the industries leading manufactures. Through
Euclid, these entire product lines are available to you just by placing a phone call
to Euclid's S.O.S. Department.
1 2 3 4
DANA
AXLE CAPACITY OUTER CONE OUTER CUP INNER CUP INNER CONE
MODEL (1) (2) (3) (4)
1 2 3 4
DEXTER
AXLE CAPACITY OUTER CONE OUTER CUP INNER CUP INNER CONE
MODEL (1) (2) (3) (4)
EATON
AXLE CAPACITY OUTER CONE OUTER CUP INNER CUP INNER CONE
MODEL (1) (2) (3) (4)
25R
E-TMHM212049 E-TMHM212011 E-TM653 E-TM665A
22R
22L
E-TMSET413
23R
E-TMHM212049 E-TMHM212011 E-TMHM218210 E-TMHM218248
23L
E-TMSET413 E-TMSET414
E-TMHM212049 E-TMHM212011 E-TM653 E-TM665A
22R
E-TMSET413
E-TMHM212049 E-TMHM212011 E-TM653 E-TM665A
22L
E-TMSET413
E-TMHM212049 E-TMHM212011 E-TM653 E-TM665A
C
E-TMSET413
E-TMHM212049 E-TMHM212011 E-TM653 E-TM665A
C2
E-TMSET413
E-TMHM212049 E-TMHM212011 E-TM653 E-TM665A
CD
E-TMSET413
E-TMHM212049 E-TMHM212011 E-TM653 E-TM665A
CD2
E-TMSET413
1 2 3 4
FRUEHAUF
AXLE CAPACITY OUTER CONE OUTER CUP INNER CUP INNER CONE
MODEL (1) (2) (3) (4)
MERITOR
AXLE CAPACITY OUTER CONE OUTER CUP INNER CUP INNER CONE
MODEL (1) (2) (3) (4)
E-9793