Professional Documents
Culture Documents
Iub TX Configuration Recommendation - ATM RAN14 V1.1
Iub TX Configuration Recommendation - ATM RAN14 V1.1
Iub TX Configuration Recommendation - ATM RAN14 V1.1
General Rules of
1. VCC Planning
Number of VCCs
supported by Number of VCCs
VCC TYPE Huawei recommended by Huawei
NCP 1 1
Signal Plane CCP 1 to 12 1
ALCAP 1 1
1+INT((AMRUserNum*2+
AAL2PATH_SHARE 1 to 16 24)/248)
User Plane
AAL2PATH_SHARE 1 to 16 1
AAL2PATH_SHARE 1 to 16 1
OAM IPOA 1 1
CBR type is preferred because it can make NCP/CCP/ALCAP signal data have higher priority than RT-VBR service data.
CBR type is recommended.
But in fact most of data at Iub interface are of NRT-VBR type. When congestion, the NRT-VBR data must be firstly discard
difference between CBR and RT-VBR for NCP/CCP/ALCAP PVC.
The number of R99 RT AAL2 paths depends on the maximum number of online users. The R99 RT AAL2 path can be ad
248 CIDs available for upper layer. These CIDs are used by common channels and R99 RT users. 4 CIDs is needed by c
and the other for AMR traffic. So
CID number for AMR users: 2 CID/user * AMRUserNum
CID number for Common Channels: 4 CID/cell * 6 Cells = 24 CIDs;
If the peer device of NodeB or RNC,suppose that, it is the ATM switch, can not support multiplex configuration, that is to s
equipment and the ATM Switch adopts different configuration policy as follows:
1)if the local configuration is CBR/RTVBR, the peer configuration is CBR/RTVBR.
2)if the local configuration is NRTVBR/UBR, the peer configuration is UBR.
3)if the peer replaces RTVBR with CBR, the local may keep RTVBR configuration in case of that the difference is not so b
4)The bandwidth configuration of the ATM Switch should be consistent with NodeB and RNC. That means, the configured
configuration.
Except this, another method may be applied. VP switch in the ATM Switch can be configured and only total bandwidth nee
2. Bandwidth Planning
The bandwidth of OAM PVC should be guaranteed when Congestion, so UBR+ is recommended. The bandwidth of OAM
3. Tx related Algorithm
CBR or RTVBR
RT_VBR
NRT_VBR
UBR
UBR+
y than RT-VBR service data. When congestion the RT-VBR type data is discarded prior to CBR type data. So
R data must be firstly discarded, while the CBR and RT-VBR can hardly be affected. So there is almost no
R99 RT AAL2 path can be added according to the actual network capacity. In one R99 RT path, there are only
users. 4 CIDs is needed by common channels of each cell; 2 CIDs is needed by one AMR call, one for signaling
ownlink congestion occurs, since theres no limitation on receiving end, congestion always appears on
gestion always appears on RNC; uplink congestion always on NodeB.
plex configuration, that is to say, all configured bandwidth can not be beyond the physical bandwidth. The
SCR(kbps) MCR(kbps)
64
SCR(kbps) MCR(kbps)
Calculated by Traffic Model
Calculated by Traffic Model
Calculated by Traffic Model
(BW_IMA - (SCR_NCP+SCR_CCP+SCR_ALCAP+OM))//the number of RT PATHs
(BW_IMA - (SCR_NCP+SCR_CCP+SCR_ALCAP+OM))//the number of RT PATHs
BW_IMA - (PCR_NCP+PCR_CCP+PCR_ALCAP)
64
nded. The bandwidth of OAM should be configured as small as possible,64kbps bandwidth is adopted.
This configuration is applicable when the middle switch between RNC and NodeB support overboo
Otherwise, refer to the "FRAATM" "multi-E1" or "unchannelled" sheets.
Huawei RNC Configuration
ATM Service Type
NCP CBR
Signal Plane CCP CBR
ALCAP CBR
AAL2PATH_SHARE RTVBR
AAL2PATH_SHARE RTVBR
User Plane
AAL2PATH_SHARE NRTVBR
AAL2PATH_SHARE UBR
OAM IPOA UBR+
Note1:This configuration is applicable when the middle switch between RNC and NodeB support overbooking configurati
(Overbooking:configured bandwidth can beyond the physical bandwidth.)
Scenario 1: It doesn't have the ATM Switch or other PVC exchange equipments between RNC and NodeB.
Scenario 2: The ATM Swtich of other euipments support overbooking.
Note3: Please use the "SET CTRLFACTOR" command to modify the Factors to the values shown as the table.
Note4: The number of the AAL2PATH R99 RTR99NRTHSPA is based on the CE of the NodeB. The formula refer to
The following number is a reference:
E1 Number R99 RT AAL2PATH Number R99 NRT AAL2PATH Number
<=1 1 1
2 2 1
3~6 3 1
>=7 3 2
Note5: If the middle ATM switch equipment doesn't support CBR or multiplexing, the ATM Service Type of Signal Plane c
ATM Service Type
Signal Plane NCP RTVBR
CCP RTVBR
ALCAP RTVBR
Note6: Generally speaking, it is enough that the 512kbps bandwidth for NCP and the 768kbps bandwidth for CCP. Becau
bandwidth of the Signal Plane doesn't use, the rest bandwidth can be used by service. Also, the larger bandwidth can imp
alternate time.
Note 7:
The recommended TRMMAP is same to the default TRMMAP. Refer to the Sheet "multi-E1"
AAL2PATH UBR
OAM IPOA UBR+
Note 1:
Note 2: The number of the AAL2PATH R99 RTR99NRTHSPA is based on the CE of the NodeB. The formula refer to
The following number is a reference:
E1 Number R99 RT AAL2PATH Number R99 NRT AAL2PATH Number
<=1 1 1
2 2 1
3~6 3 1
>=7 3 2
and NodeB support overbooking configuration or the cell covers the hot spot.
ng, the ATM Service Type of Signal Plane can be configured to RTVBR.
PCR(kbps) SCR(kbps) MBS(cell) CDVT(0.1us)
560 512 1024
840 768 1024
280 256 1024
and the 768kbps bandwidth for CCP. Because the bandwidth of this configuration is multiplex and Factor is 10, if the
service. Also, the larger bandwidth can improve the alternate rate and reduce the
e Sheet "multi-E1"
BW_IMAorUNIorFRA
512
MCR(kbps) FACTOR
10
10
10
64 10
RCR(kbps) MCR(kbps)
INT(BW_IMAorUNIorFRA/1.1/8)*8
INT(BW_IMAorUNIorFRA/1.1/8)*8
BW_IMAorUNIorFRA -
INT(BW_IMAorUNIorFRA/1.1/8)*8
(PCR_NCP*active factor of
NCP+PCR_CCP*active factor of
CCP
+PCR_ALCAP*active factor of
ALCAP)
64
This configuration is applicable when the middle switch between RNC and NodeB doesn't s
sheet.
NCP
Signal Plane CCP
ALCAP
AAL2PATH_SHARE
User Plane AAL2PATH_SHARE
AAL2PATH_SHARE
OAM IPOA
NCP
Signal Plane CCP
ALCAP
AAL2PATH_SHARE
User Plane AAL2PATH_SHARE
AAL2PATH_SHARE
OAM IPOA
NCP
Signal Plane CCP
ALCAP
AAL2PATH_SHARE
AAL2PATH_SHARE
User Plane
AAL2PATH_SHARE
AAL2PATH_SHARE
OAM IPOA
NCP
Signal Plane CCP
ALCAP
AAL2PATH_SHARE
AAL2PATH_SHARE
User Plane
NCP
Signal Plane CCP
ALCAP
AAL2PATH_SHARE
AAL2PATH_SHARE
User Plane AAL2PATH_SHARE
AAL2PATH_SHARE
AAL2PATH_SHARE
OAM IPOA
NCP
Signal Plane CCP
ALCAP
AAL2PATH_SHARE
AAL2PATH_SHARE
User Plane AAL2PATH_SHARE
AAL2PATH_SHARE
AAL2PATH_SHARE
OAM IPOA
NCP
Signal Plane CCP
ALCAP
AAL2PATH_SHARE
AAL2PATH_SHARE
User Plane AAL2PATH_SHARE
AAL2PATH_SHARE
AAL2PATH_SHARE
OAM IPOA
NCP
Signal Plane CCP
ALCAP
AAL2PATH_SHARE
AAL2PATH_SHARE
AAL2PATH_SHARE
User Plane AAL2PATH_SHARE
AAL2PATH_SHARE
AAL2PATH_SHARE
AAL2PATH_SHARE
OAM IPOA
NCP
Signal Plane CCP
ALCAP
AAL2PATH_SHARE
AAL2PATH_SHARE
AAL2PATH_SHARE
User Plane AAL2PATH_SHARE
AAL2PATH_SHARE
AAL2PATH_SHARE
AAL2PATH_SHARE
OAM IPOA
AAL2PATH_SHARE
IMA group 0 (2E1) User Plane
AAL2PATH_SHARE
NCP
Signal Plane CCP
ALCAP
AAL2PATH_SHARE
AAL2PATH_SHARE
IMA group 1 (8E1) AAL2PATH_SHARE
User Plane
AAL2PATH_SHARE
IMA group 0 (3E1) User Plane
AAL2PATH_SHARE
NCP
Signal Plane CCP
ALCAP
AAL2PATH_SHARE
AAL2PATH_SHARE
IMA group 1 (8E1) AAL2PATH_SHARE
User Plane AAL2PATH_SHARE
AAL2PATH_SHARE
AAL2PATH_SHARE
AAL2PATH_SHARE
OAM IPOA
AAL2PATH_SHARE
IMA group 0 (4E1) User Plane AAL2PATH_SHARE
AAL2PATH_SHARE
NCP
Signal Plane CCP
ALCAP
AAL2PATH_SHARE
AAL2PATH_SHARE
IMA group 1 (8E1) AAL2PATH_SHARE
User Plane AAL2PATH_SHARE
AAL2PATH_SHARE
AAL2PATH_SHARE
AAL2PATH_SHARE
OAM IPOA
Note1: Please use the "SET CTRLFACTOR" command to modify the Factor values shown as the table.
Note 2:
When the number of E1 is under 4(1*UNI, IMA 1*E1, IMA 2*E1, IMA 3*E1), the bandwidth of NCP and ALCAP cite the
calculated from the traffic model.
Note 3:
The recommended TRMMAP is same to the default TRMMAP Refer to MML ''ADD/MODTRMMAP.''
TRMMAP(Iub) ATM
Service Type Default
Primary Secondary
Common channel RT_VBR NULL
IMS SRB RT_VBR NULL
SRB RT_VBR NULL
AMR voice RT_VBR NULL
R99 CS
RT_VBR NULL
conversational
R99 CS streaming RT_VBR NULL
R99 PS
RT_VBR NULL
conversational
R99 PS streaming RT_VBR NULL
R99 PS high PRI
NRT_VBR NULL
interactive
R99 PS middle PRI
NRT_VBR NULL
interactive
R99 PS low PRI
NRT_VBR NULL
interactive
R99 PS
NRT_VBR NULL
background
HSDPA Signal RT_VBR NULL
HSDPA IMS Signal RT_VBR NULL
HSDPA Voice RT_VBR NULL
HSDPA
RT_VBR NULL
conversational
HSDPA streaming RT_VBR NULL
HSDPA high PRI
UBR NULL
interactive
HSDPA middle PRI
UBR NULL
interactive
HSDPA low PRI
UBR NULL
interactive
HSDPA background UBR NULL
HSUPA Signal RT_VBR NULL
HSUPA IMS Signal RT_VBR NULL
HSUPA Voice RT_VBR NULL
HSUPA
RT_VBR NULL
conversational
HSUPA streaming RT_VBR NULL
HSUPA high PRI
UBR NULL
interactive
HSUPA middle PRI
UBR NULL
interactive
HSUPA low PRI
UBR NULL
interactive
HSUPA background UBR NULL
NCP
Signal Plane CCP
ALCAP
AAL2PATH
User Plane AAL2PATH
AAL2PATH
OAM IPOA
NCP
Signal Plane CCP
ALCAP
AAL2PATH
User Plane AAL2PATH
AAL2PATH
OAM IPOA
NCP
Signal Plane CCP
ALCAP
AAL2PATH
AAL2PATH
User Plane
AAL2PATH
AAL2PATH
OAM IPOA
NCP
Signal Plane CCP
ALCAP
AAL2PATH
AAL2PATH
User Plane AAL2PATH
AAL2PATH
AAL2PATH
OAM IPOA
NCP
Signal Plane CCP
ALCAP
AAL2PATH
AAL2PATH
User Plane AAL2PATH
AAL2PATH
AAL2PATH
OAM IPOA
NCP
Signal Plane CCP
ALCAP
AAL2PATH
AAL2PATH
User Plane AAL2PATH
AAL2PATH
AAL2PATH
OAM IPOA
NCP
Signal Plane CCP
ALCAP
AAL2PATH
AAL2PATH
User Plane AAL2PATH
AAL2PATH
AAL2PATH
OAM IPOA
NCP
Signal Plane CCP
ALCAP
AAL2PATH
AAL2PATH
AAL2PATH
User Plane AAL2PATH
AAL2PATH
AAL2PATH
AAL2PATH
OAM IPOA
NCP
Signal Plane CCP
ALCAP
AAL2PATH
AAL2PATH
User Plane
10/07/2017 Confidential Information of Huawei.No Spreading without Permission Page 19 of 94
368036482.xls SecurityFor Internal
AAL2PATH
User Plane AAL2PATH
AAL2PATH
AAL2PATH
AAL2PATH
OAM IPOA
AAL2PATH
IMA group 0 (2E1) User Plane
AAL2PATH
NCP
Signal Plane CCP
ALCAP
AAL2PATH
AAL2PATH
IMA group 1 (8E1) AAL2PATH
User Plane AAL2PATH
AAL2PATH
AAL2PATH
AAL2PATH
OAM IPOA
AAL2PATH
IMA group 0 (3E1) User Plane
AAL2PATH
NCP
Signal Plane CCP
ALCAP
AAL2PATH
AAL2PATH
IMA group 1 (8E1) AAL2PATH
User Plane
AAL2PATH
IMA group 0 (4E1) User Plane AAL2PATH
AAL2PATH
NCP
Signal Plane CCP
ALCAP
AAL2PATH
AAL2PATH
IMA group 1 (8E1) AAL2PATH
User Plane AAL2PATH
AAL2PATH
AAL2PATH
AAL2PATH
OAM IPOA
Note 1:
The IMA Group parameters includeing ITC/CTC should be same with the directly connected peer device.
Note 2:
NodeB Resource group configuration is not recommended except needed.
Note 3:
When the number of E1 is under 4(1*UNI, IMA 1*E1, IMA 2*E1, IMA 3*E1), the bandwidth of NCP and ALCAP cite the
value of 4*E1; the bandwidth of CCP is 1.3 times of the value calculated from the traffic model.
Note 4: The number of the AAL2PATH R99 RTR99NRTHSPA is based on the CE of the NodeB. The formula refe
The following number is a reference:
E1 Number R99 RT AAL2PATH NumberR99 NRT AAL2PATH Number
<=1 1 1
2 2 1
3~6 3 1
>=7 3 2
switch between RNC and NodeB doesn't support overbooking configuration. Otherwise, refer to the "Ove
1, IMA 3*E1), the bandwidth of NCP and ALCAP cite the corresponding value of 4*E1; the bandwidth of CCP is 1.3 times of the value
UBR+ 512
d except needed.
1, IMA 3*E1), the bandwidth of NCP and ALCAP cite the corresponding
ed from the traffic model.
SPA is based on the CE of the NodeB. The formula refer to "General Rules".
MCR(kbps) FACTOR
30
30
20
64 10
MCR(kbps) FACTOR
30
30
20
64 10
MCR(kbps) FACTOR
30
30
20
64 10
MCR(kbps) FACTOR
30
30
20
64 10
MCR(kbps) FACTOR
30
30
20
64 10
MCR(kbps) FACTOR
30
30
20
64 10
MCR(kbps) FACTOR
30
30
20
64 10
MCR(kbps) FACTOR
30
30
20
64 10
MCR(kbps) FACTOR
30
30
20
64 10
MCR(kbps) FACTOR
30
30
20
64 10
MCR(kbps) FACTOR
30
30
20
64 10
MCR(kbps) FACTOR
30
30
20
64 10
MCR(kbps) FACTOR
30
30
20
64 10
RCR(kbps) MCR(kbps)
1360
1424
1696
64
RCR(kbps) MCR(kbps)
1344
1408
1680
64
RCR(kbps) MCR(kbps)
1576
1576
3224
3536
64
RCR(kbps) MCR(kbps)
1656
1656
1656
5040
5400
64
RCR(kbps) MCR(kbps)
2232
2232
2232
6768
7216
64
RCR(kbps) MCR(kbps)
2824
2824
2824
8552
9064
64
RCR(kbps) MCR(kbps)
3400
3400
3400
10264
10872
64
RCR(kbps) MCR(kbps)
3992
3992
3992
12040
12040
12712
12712
64
RCR(kbps) MCR(kbps)
4568
4568
4568
13784
13784
14544
14544
64
RCR(kbps) MCR(kbps)
1730
4568
4568
4568
13784
13784
14544
14544
64
RCR(kbps) MCR(kbps)
3461
3461
4568
4568
4568
13784
13784
14544
14544
64
RCR(kbps) MCR(kbps)
5192
5192
4568
4568
4568
13784
13784
14544
14544
64
RCR(kbps) MCR(kbps)
6923
6923
6923
4568
4568
4568
13784
13784
14544
14544
64
This configuration is applicable when the middle switch between RNC and NodeB doesn't supp
Otherwise, refer to the "Overbooking Configuration" sheet.
Huawei RNC Configuration
Scenario 1: FRAATM 12TS
ATM Service Type PCR(kbps) SCR(kbps) MBS(cell)
NCP CBR 104
Signal CCP CBR 48
Plane
ALCAP CBR 56
AAL2PATH_SHARE RTVBR 544 496 1000
User Plane AAL2PATH_SHARE NRTVBR 768 336 1000
AAL2PATH_SHARE UBR 768
OAM IPOA UBR+ 512
Note1: Please use the "SET CTRLFACTOR" command to modify the Factor values shown as the table.
Note1: Please use the "SET CTRLFACTOR" command to modify the Factor values shown as the table.
Note1: Please use the "SET CTRLFACTOR" command to modify the Factor values shown as the table.
Note1: Please use the "SET CTRLFACTOR" command to modify the Factor values shown as the table.
Note2:The recommended TRMMAP is same to the default TRMMAP.Refer to the Sheet "multi-E1"
Note 1:
wn as the table.
wn as the table.
wn as the table.
wn as the table.
eet "multi-E1"
10240 496
10240 336
672
64
10240 680
10240 528
856
64
10240 1128
10240 1024
1304
64
10240 1224
10240 1096
1416
64
This configuration is applicable when unchannelled optical port is used in both RNC and No
Note1: Please use the "SET CTRLFACTOR" command to modify the Factor values shown as the table.
Note1: Please use the "SET CTRLFACTOR" command to modify the Factor values shown as the table.
Note1: Please use the "SET CTRLFACTOR" command to modify the Factor values shown as the table.
User Plane
10/07/2017 4594
368036482.xls
Note1: Please use the "SET CTRLFACTOR" command to modify the Factor values shown as the table.
Note1: Please use the "SET CTRLFACTOR" command to modify the Factor values shown as the table.
Note1: Please use the "SET CTRLFACTOR" command to modify the Factor values shown as the table.
Note1: Please use the "SET CTRLFACTOR" command to modify the Factor values shown as the table.
10/07/2017 4694
368036482.xls
Note1: Please use the "SET CTRLFACTOR" command to modify the Factor values shown as the table.
Note1: Please use the "SET CTRLFACTOR" command to modify the Factor values shown as the table.
Note1: Please use the "SET CTRLFACTOR" command to modify the Factor values shown as the table.
10/07/2017 4794
368036482.xls
Note1: Please use the "SET CTRLFACTOR" command to modify the Factor values shown as the table.
Note1: Please use the "SET CTRLFACTOR" command to modify the Factor values shown as the table.
Note1: Please use the "SET CTRLFACTOR" command to modify the Factor values shown as the table.
User Plane
10/07/2017 4894
368036482.xls
Note1: Please use the "SET CTRLFACTOR" command to modify the Factor values shown as the table.
Note1: Please use the "SET CTRLFACTOR" command to modify the Factor values shown as the table.
Note1: Please use the "SET CTRLFACTOR" command to modify the Factor values shown as the table.
10/07/2017 4994
368036482.xls
User Plane
Note1: Please use the "SET CTRLFACTOR" command to modify the Factor values shown as the table.
Note 2:
1.When the bandwidth is less than 15M(8*E1 IMA), the configuration can refer to multi-E1;
2.When the bandwidth exceed 15M, the control plane can refer to the Scenario 9 (the control plane bandwidth of
Scenario 9 is enough for one NodeB including all traffic), the formula of user plane bandwidth as following:
AAL2PATH_RTVBR_SCR=(IUB_bandwidthcontrol_planeOMCH_MCR)/number_of_ AAL2PATH_RTVBR;
AAL2PATH_RTVBR_PCR=AAL2PATH_RTVBR_SCR*1.1;
AAL2PATH_NRTVBR_PCR=IUB_bandwidth;
AAL2PATH_NRTVBR_SCR=AAL2PATH_NRTVBR_PCR/1.1;
AAL2PATH_UBR_PCR=IUB_bandwidth;
OMCH_MCR=64kbps.
Note 3:
The recommended TRMMAP is same to the default TRMMAP Refer to MML ''ADD/MODTRMMAP.''
TRMMAP(Iub) ATM
Service Type
Default Recommended
Primary Secondary Primary
Common channel RT_VBR NULL RT_VBR
IMS SRB RT_VBR NULL RT_VBR
SRB RT_VBR NULL RT_VBR
AMR voice RT_VBR NULL RT_VBR
R99 CS conversational RT_VBR NULL RT_VBR
R99 CS streaming RT_VBR NULL RT_VBR
R99 PS conversational RT_VBR NULL RT_VBR
R99 PS streaming RT_VBR NULL RT_VBR
R99 PS high PRI interactive NRT_VBR NULL NRT_VBR
R99 PS middle PRI interactive NRT_VBR NULL NRT_VBR
R99 PS low PRI interactive NRT_VBR NULL NRT_VBR
R99 PS background NRT_VBR NULL NRT_VBR
HSDPA Signal RT_VBR NULL RT_VBR
HSDPA IMS Signal RT_VBR NULL RT_VBR
HSDPA Voice RT_VBR NULL RT_VBR
HSDPA conversational RT_VBR NULL RT_VBR
HSDPA streaming RT_VBR NULL RT_VBR
HSDPA high PRI interactive UBR NULL UBR
HSDPA middle PRI interactive UBR NULL UBR
HSDPA low PRI interactive UBR NULL UBR
HSDPA background UBR NULL UBR
HSUPA Signal RT_VBR NULL RT_VBR
HSUPA IMS Signal RT_VBR NULL RT_VBR
HSUPA Voice RT_VBR NULL RT_VBR
HSUPA conversational RT_VBR NULL RT_VBR
HSUPA streaming RT_VBR NULL RT_VBR
HSUPA high PRI interactive UBR NULL UBR
HSUPA middle PRI interactive UBR NULL UBR
10/07/2017 5094
368036482.xls
10/07/2017 5194
368036482.xls
User Plane
AAL2PATH NRTVBR 5712
AAL2PATH UBR 5712
OAM IPOA UBR+ 512
10/07/2017 5294
368036482.xls
Signal Plane
ALCAP CBR 176
AAL2PATH RTVBR 4384
AAL2PATH RTVBR 4384
AAL2PATH RTVBR 4384
User Plane
AAL2PATH NRTVBR 13328
AAL2PATH NRTVBR 13328
AAL2PATH UBR 13328
AAL2PATH UBR 13328
OAM IPOA UBR+ 512
10/07/2017 5394
368036482.xls
User Plane
10/07/2017 5494
368036482.xls
Note 1:
1. NodeB Resource group configuration is not recommended except needed.
Note 2:
1.When the bandwidth is less than 15M(8*E1 IMA), the configuration can refer to multi-E1;
2.When the bandwidth exceed 15M, the control plane can refer to the Scenario 9 (the control plane bandwidth of
Scenario 9 is enough for one NodeB including all traffic), the formula of user plane bandwidth as following:
AAL2PATH_RTVBR_SCR=(IUB_bandwidthcontrol_planeOMCH_MCR)/number_of_ AAL2PATH_RTVBR;
AAL2PATH_RTVBR_PCR=AAL2PATH_RTVBR_SCR*1.1;
AAL2PATH_NRTVBR_PCR=IUB_bandwidth;
AAL2PATH_NRTVBR_SCR=AAL2PATH_NRTVBR_PCR/1.1;
AAL2PATH_UBR_PCR=IUB_bandwidth;
OMCH_MCR=64kbps.
10/07/2017 5594
368036482.xls
10/07/2017 5694
368036482.xls
10/07/2017 5794
368036482.xls
10/07/2017 5894
368036482.xls
1024 30
1024 20
7824 1000 1024
7824 1000 1024
7824 1000 1024
23552 1000 1024
23552 1000 1024
1024
1024
1024 64 10
10/07/2017 5994
368036482.xls
10/07/2017 6094
368036482.xls
o multi-E1;
9 (the control plane bandwidth of
ne bandwidth as following:
mber_of_ AAL2PATH_RTVBR;
''ADD/MODTRMMAP.''
Recommended
Secondary TRMMAP(Iub-atm).rar
NULL
NULL
NULL
NULL
NULL
NULL
NULL
NULL
NULL
NULL
NULL
NULL
NULL
NULL
NULL
NULL
NULL
NULL
NULL
NULL
NULL
NULL
NULL
NULL
NULL
NULL
NULL
NULL
10/07/2017 6194
368036482.xls
NULL
NULL
10/07/2017 6294
368036482.xls
10/07/2017 6394
368036482.xls
10/07/2017 6494
368036482.xls
10/07/2017 6594
368036482.xls
o multi-E1;
9 (the control plane bandwidth of
ne bandwidth as following:
mber_of_ AAL2PATH_RTVBR;
10/07/2017 6694
368036482.xls SecurityFor Internal
Note1:
If the license(ATM IUB overbooking) is open in RNC, LP is recommended.
ATM Logic port is introduced for traffic shaping, congestion detection and backpressure;
when the the minimum bandwidth of physical link connection between RNC and NodeB is less than the physical bandwid
RNC or NodeB,Logic port is strongly recommended to configure in RNC side.
(For example, STM-1 in RNC side, E1 in NODEB side) . The Logic Port is cited by the SAALLNK, AAL2PATH, IPOAPVC
other LP.)
Scenario 1: The interface board of RNC is UOI board. RNC configures one LP Leaf Port for each NodeB.
Scenario 2: Several NodeBs converge. RNC configues the LP HUB Port for the converge point.
Note2:
If the Node is the last node, the type of the Logic port is Leaf Node. Otherwise, it is the Hub Node.
Note3:
If the ATM traffic shaping and congestion control functions or the user plane resource separation by operators in RAN sha
ADD ATMLOGICPORT command, set The bearing type of the virtual port to ATMLOGICPORT , which indicates that the A
Backward bandwidth(kbps)
Min bandwidth from RNC to NodeB
kpressure;
nd NodeB is less than the physical bandwidth of
ied operator.
FAQ
AQ
ommendation_IP"
No.
1
2
3
4
5
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
description
Modify PCR=6760 limitation of NodeB with 15232kbps according to the specification modification afte
ADD bandwidth recommended configuration when unchannelled optical port is used in both RNC and
NodeB side(NodeB UUAS subboard(unchannalled optical port ) of UTRP extended interface board is
used).
Refresh the application Scenario description of Overbooking and Multi-E1FRAATM.
Refresh the control plane bandwidth when the number of E1 under 4.
Extend the bandwidth of control plane to avoid the risk of congestion(South AfricaAustrilia),NCP
extend 50%,CCP extend 30%,ALCAP extend 100%.
Reduce the active factor of control plane to avoid the risk of congestion, NCP reduce to 30%,CCP
reduce to 30%,ALCAP reduce to 30%.
Add a R99NRT path and a HSPA path to avoid the CID congestion.(hongkong) when E1s more than 7.
Draw the scene of configure IPLOGICPORT /ATMLOGICPORT,make the understanding of mind easily.
Modify the R99 PS service and HSPA background service active factor to accord to conduction default
configuration.
Extend bandwidth recommended configuration to 55M to satisfy 64QAMMIMODC requirement
when unchannelled optical port is used in both RNC and NodeB side(NodeB UUAS
subboard(unchannalled optical port ) of UTRP extended interface board is used).
Add the configuration principle for 9 to 12 E1 (2 IMA group).
Change the bandwidth to integral times to eight.
Add PCR bandwidth for UBR+ type in RNC side
time Reviser
zhangyong,wangzecai
4/10/2007 zhangyonggan
4/30/2007 zhangyonggan
5/8/2007 zhangyonggan
10/8/2007 wangzecai
11/28/2007 zhangyonggan
11/29/2007 zhangyonggan
1/24/2008 zhushimin
1/24/2008 zhushimin
1/26/2008 zhushimin
3/3/2008 zhushimin
4/25/2008 liuli
4/25/2008 liuli
4/25/2008 liuli
4/25/2008 liuli
4/25/2008 liuli
4/25/2008 liuli
4/25/2008 liuli
4/25/2008 liuli
4/25/2008 liuli
8/22/2008 zhushimin
1/12/2009 zhushimin
1/12/2009 zhushimin
1/20/2009 zhushimin
1/21/2009 zhushimin
4/3/2009 zhushimin
4/3/2009 zhushimin
4/3/2009 zhushimin
4/3/2009 zhushimin
8/5/2009 zhangyonggan
1/7/2009 huangmuhua
2/23/2010 huangmuhua
2/23/2010 huangmuhua
1/13/2011 huangmuhua
1/13/2011 huangmuhua
1/13/2011 huangmuhua
1/13/2011 huangmuhua
1/13/2011 huangmuhua
1/13/2011 huangmuhua
1/14/2011 Lu Feng
1/19/2011 Lu Feng
7/15/2011 huangmuhua
The Maximum Number of Online User for Different E1s at the Same Time
Num. of E1 Num. of Cells per NodeB The Maximum Number of Online User
1 3 50
2 3 100
3 3 150
4 3 200
5 3 250
6 3 300
7 3 350
8 3 372
1 6 100
2 6 150
3 6 200
4 6 300
5 6 350
6 9 400
7 9 450
8 12 500
15 3 35
22 3 45
24 3 50
NRTVBR: 1 1
6000000+10000000(MBS-1 )( )<13369344 ( rate unit:cell/s)
SCR PCR
RTVBR: 1 1
CDVT +10000000( MBS-1 )( )<13369344 (rate unit:cell/s)
SCR PCR
R99 cell common measurement report + H common measurement report + the signaling due to CS, PS and RRC accessing procedur
due to soft handover
The main flux is due to common measurement report.
Flux of NCP Downlink:
the signaling due to CS, PS and RRC only on DCH accessing procedure + the signaling due to soft handover
Flux of CCP Uplink:
the signaling due to CS, PS and RRC only on DCD accessing procedure + the signaling due to softer handover + the signaling of RL d
soft handover + the dedicated measurement report of TCP due to DPB
The main flux is due to dedicated measurement report of TCP for DPB on every RL which is in macro diversity.
Flux of CCP Downlink:
the signaling due to CS, PS and RRC only on DCH accessing procedure + the signaling due to softer handover + the signaling of DPB
RLs in macro diversity.
The main flux is due to the signaling of DPB request.
Flux of ALCAP Uplink:
the signaling due to CS, PS and RRC only on DCH accessing procedure + the signaling due to soft handover
Flux of ALCAP Downlink:
the signaling due to CS, PS and RRC only on DCH accessing procedure + the signaling due to soft handover
Size of Signaling
RL_SETUP_RSP 102
COMM_MEAS_RPRT(RTWP) 24
COMM_MEAS_RPRT(Cell TCP) 23
COMM_MEAS_RPRT(Non Hsdpa Power) 27
COMM_MEAS_RPRT(PBR) 35
COMM_MEAS_RPRT(GBR) 36
CCP Downlink Signaling
Name of Signaling Size of Signaling
DEDI_MEAS_INIT_REQ(SIRErr_E_Event) 52
DEDI_MEAS_INIT_REQ(SIRErr_F_Event) 52
DEDI_MEAS_INIT_REQ(TCP)[DPB] 49
DL_PWR_CTRL_REQ 41
RL_RECFG_PREP 224
RL_RECFG_COMMIT 20
RL_DELETE_REQ 33
RL_ADD_REQ 41
the signaling due to CS, PS and RRC only on DCH accessing procedure
the signaling due to softer handover
the signaling due to soft handover
CCP Uplink Signaling
Name of Signaling Size of Signaling
RL_RESTORE_IND 26
DEDI_MEAS_INIT_RSP(SIRErr_E_Event) 24
DEDI_MEAS_INIT_RSP(SIRErr_F_Event) 24
RL_RECONFIG_READY 91
RL_DELETE_RESPONSE 17
RL_ADD_RSP 31
DEDI_MEAS_INIT_RSP(TCP FOR DPB) 24
RL_DELETE_RESPONSE 17
DEDI_MEAS_RPRT(TCP FOR DPB)
the signaling due to CS, PS on DCH accessing procedure
the signaling due to RRC only on DCH accessing procedure
the signaling due to softer handover
the signaling due to soft handover
QAAL2 Downlink Signaling
Name of Signaling Size of Signaling
QAAL2_ESTABLISH_REQ 83
QAAL2_MODIFY_REQ 21
QAAL2_RELEASE_REQ 12
the signaling due to CS, PS on DCH accessing procedure
the signaling due to RRC only on DCH accessing procedure
the signaling due to soft handover
QAAL2 Uplink Signaling
Name of Signaling Size of Signaling
QAAL2_ESTABLISH_CONFIRM 16
QAAL2_MODIFY_ACKNOWLEDGE 6
QAAL2_RELEASE_CONFIRM 12
the signaling due to CS, PS on DCH accessing procedure
the signaling due to RRC only on DCH accessing procedure
the signaling due to soft handover
Num. of E1 Num. of Cells per NodeB The Maximum Number of Online User
1 3 50
2 3 100
3 3 150
4 3 200
5 3 250
6 3 300
7 3 350
8 3 372
1 6 100
2 6 150
3 6 200
4 6 300
5 6 350
6 9 400
7 9 450
8 12 500
Num. of TS Num. of Cells per NodeB The Maximum Number of Online User
12 3 25
15 3 35
22 3 45
24 3 50
Flux of NCP
Num. of E1 Number of R99Cell Number of H Cell Flux of NCP Uplink Downlink
1 0 3 69571 13215
2 0 3 76179 26429
3 0 3 82786 39644
4 0 3 89393 52859
5 0 3 96001 66073
6 0 3 102608 79288
7 0 3 109215 92503
8 0 3 112123 98317
1 3 3 97167 26429
2 3 3 103774 39644
3 3 3 110381 52859
4 3 3 123596 79288
5 3 3 130203 92503
6 3 6 199775 105717
7 3 6 206382 118932
8 6 6 233977 132147
Flux of NCP
Num. of TS Number of R99Cell Number of H Cell Flux or NCP Uplink Downlink
12 0 3 66268 6607
15 0 3 67589 9250
22 0 3 68911 11893
24 0 3 69571 13215
mensioning Tool
g.
procedure and size of signaling.
of bandwidth has already planned.
/h
s
s
/s
s
s
0
0
0
0
0
0
2
0
0
0
0
0
0
0
0
soft handover
macro diversity.
soft handover
soft handover
Default
Period(
SAAL PDU AAL5 PDU ms) Flux comment
108 144 None
28 48 400 R99 cell common
28 48 200 360 measurement report
32 48 200
40 48 200 H common
40 48 200 720 measurement report
56 96
56 96
56 96
48 96 the signaling of DPB request on the RLs in macro diversity
228 240
24 48
40 48
48 96
528
432
336
24 48
48 0.7 68.571428571 the dedicated report of TCP due to DPB
336
192
240
192
88 96
28 48
16 48
336
144
144
20 48
12 48
16 48
240
96
96
Flux of Flux of
Flux of CCP Flux of CCP ALCAP ALCAP
Uplink Downlink Uplink Downlink
48343 67628 6737 9717
96685 135256 13474 19433
145028 202884 20211 29150
193371 270512 26948 38867
241714 338140 33684 48583
290056 405768 40421 58300
338399 473396 47158 68017
359670 503152 50122 72292
96685 135256 13474 19433
145028 202884 20211 29150
193371 270512 26948 38867
290056 405768 40421 58300
338399 473396 47158 68017
386742 541024 53895 77733
435085 608652 60632 87450
483427 676280 67369 97167
Flux of Flux of
Flux of CCP Flux of CCP ALCAP ALCAP
Uplink Uplink Uplink Downlink
24171 33814 3368 4858
33840 47340 4716 6802
43508 60865 6063 8745
48343 67628 6737 9717
1.375
1.528