Professional Documents
Culture Documents
UDAS Flapperdress Downloadable Resized
UDAS Flapperdress Downloadable Resized
UDAS Flapperdress Downloadable Resized
dress
Project photo on page 26;
instructions on page 66
0
selvedge
F
5
Back (B)
Flapper Dress
55 main/ lining
All sizes 1 yd
Front (A)
selvedge
55"
tulle
all sizes
selvedge
selvedges
Upper Peplum Piece (D)
Flapper Dress
55 Tulle Upper Peplum Piece (D)
selvedges
Upper Peplum Piece (D)
selvedge
XL
L
pattern
M
XS
S
M
S
L
XS
XL
downloaded.
L
XL
1 |
S
L
When prepar-
cut on fold
M
ing to print the pdf, Button + buttonhole
XS
S
make sure that you are placement marks Solid lines indi-
XS
printing it at 100% and cate buttonholes. A large open circle is
that there is no scaling. the button symbol and shows placement.
Check the settings for
page scaling (should be Test Square XS
S Cutting lines Multisize
None) and check the
2" 2" M
patterns have different cutting
preview to make sure L
XL cut on fold lines for each size.
that you will be printing
at full size. Make sure
that the box labeled Place on fold bracket This is
Auto-Rotate and a grainline marking with arrows pointing
XS
Center is unchecked to the edge of the pattern. Place on the
S
M (instructions apply specifically to Adobe Reader; if using ASYMMETRICAL FOLDS
fold of the fabric so that SKIRT
your finished
L RIGHT FRONT
XL another pdf reader, check for similar settings). piece will be twice the size of the pattern
|
2 To ensure that the pattern has printed at the correct scale, piece,cut 2 XXxx
without adding a seam.
XL
check the size of the TEST SQUARE. The Test Square
L
should be 2" 2". Grainline The double-ended arrow
M
|
3 To begin assembling the pattern, cut off or fold the dotted should be parallel to the lengthwise
margin around each page.
grain or fold unless specifically marked
|
4 The pages are numbered in rows, so the first row of pages as crosswise. Bias grainlines will be
ASYMMETRICAL
1a, 1b, 1c, etc. Line up FOLDS
the rows andSKIRT
XL
Use the illustrated guide to match each piece. Once the pattern
cut 2 XXxx XS
Notches Notches are triangle-
S
is complete, find your size, pin the pattern to the fabric, and fol- S
M
XS
low the coordinating line to cut out or trace the pattern. L shaped symbols used for accurately
XL
matching seams. Pieces to be joined will
Layout, Marking + Cutting Guidelines have corresponding notches.
1 |
Find the lines that correspond to your size and trace cut on fold
the pattern pieces, either on tissue paper or directly onto Darts Dashed lines and dots mark
the fabric, using tracing paper and a tracing wheel.
darts. The dashed lines show where the
|
2 If you are cutting pattern pieces on the fold or cutting stitching will be, and the dot shows the
cut two
on of the same pattern piece, fold the fabric in half,
fold XL
position of the dart point (signaling the
selvedge to selvedge, with right sides together. Note that this
L
point, at the end of the dart, where your
M
S
S
XS
1a 1b 1c 1d 1e 1f
cut here for lining
XS,S,M,L,XL
Cut 1 lining
Cut 1 main
Back (B)
FLAPPER DRESS
)
/ c , L, X CE (C
ld
tulle S, M M PIE SS
n fo
E
DR
st o
tra L
ER
XS, LU
on
PP
PEP
FLA
ER
3a 3b 3c 3d 3e 3f
D
UN
t1
cu
4a 4b 4c 4d 4e 4f
UPPER PEPLUM PIECE (D)
Cut 8 Tulle / contrast
FLAPPER DRESS
XS,S,M,L,XL
XL
XL
XL
XS
M
S
L
5a 5b 5c 5d 5e 5f
L
FLAPPER DRESS
Cut 1 main
Cut 1 lining
XS,S,M,L,XL
M
Front (A)
S
S
XS
XS
6a 6b 6c 6d 6e 6f
Zipper on left
side seam only
XL
PPER DRESS
PEPLUM PIECE (D)
8 Tulle / contrast
XS,S,M,L,XL
4b
XL
XS
S
M
L
XL
4c
4d
4e
4f
5a
XS S M L
FLAP
UPPER PE
Cut 8 T
XS,
cut here for main
cut here lor lining
L M S XS
5b
5c
XS,S,M,L,XL
5d
FLAPPER DRESS
Front (A)
5e Cut 1 main
Cut 1 lining
XS,S,M,L,XL
5f
6a
6b
6c
Zipper on left
side seam only
6d
6e
6f