Professional Documents
Culture Documents
Power Mirror Control System: Parts Location
Power Mirror Control System: Parts Location
PARTS LOCATION
- RR DEF RELAY
- RR DEF FUSE
MI
- ECU-ACC FUSE
- ECU-IG FUSE
B137068E01
MI2 MIRROR POWER MIRROR CONTROL SYSTEM
SYSTEM DIAGRAM
E3
Outer Mirror Switch Assembly
MI I3
Outer Rear View Mirror (LH)
8
from ECU-ACC fuse B
1 5
MH MLH
5 4
MV MLV
2 6
M+ M+
H2
Outer Rear View Mirror (RH)
1 2
MH MRH
5 3
MV MRV
2 7
M+ E
B140703E01
MIRROR POWER MIRROR CONTROL SYSTEM MI3
E38 F16
A/C Amplifier Heater Control
Engine Room R/B, J/B Assembly Panel Assembly
RR DEF Relay MI
from A/C No. 2 fuse 1 2 38
1 1 RDFG
37 9
LIN1 TX+
from RR DEF fuse 5 3
1 1
H2
3 4
I3
3 4
: LIN
B137069E01
MI4 MIRROR POWER MIRROR CONTROL SYSTEM
PARTS LOCATION
MI
- ECU-ACC FUSE
B137081E01
MI6 MIRROR INNER REAR VIEW MIRROR
COMPONENTS
without EC Mirror:
MI
INNER REAR VIEW MIRROR ASSEMBLY INNER REAR VIEW MIRROR ASSEMBLY
with EC Mirror:
MI
SYSTEM DIAGRAM
4
MI from ECU-IG No. 1 Fuse IG
1
E
C B111209E20
MIRROR INNER REAR VIEW MIRROR MI9
CALIBRATION
1. SELECT COMPASS DISPLAY MODE
(a) The COMP switch allows you to select the Display
or Non-display mode of the compass.
2. SET ZONE
(a) Deviation between the "magnetic north" and "actual
north" differs depending on the location. Therefore,
adjustment of the magnetism is required. Since the MI
magnetic condition differs depending on the area
where the vehicle is used, it is necessary for each
user to set the zone (Refer to Compass Zone Map).
The zone setting can be changed using the COMP
switch of the inner mirror.
3. PERFORM CALIBRATION
(a) Because each vehicle has its own magnetic field,
calibration should be performed for each vehicle.
This compass function is used when storing the
record of the vehicle's magnetic field.
4. WHEN COMPASS IS MAGNETIZED
(a) A compass could be magnetized during shipping by
vessels or freight cars. Therefore, make sure to
perform calibration and ensure that calibration is
performed properly before delivery. If it cannot be
done (cannot be completed in spite of driving
around several times), it may be caused by
magnetization. Demagnetize the vehicle using a
demagnetizer and perform calibration again.
MI10 MIRROR INNER REAR VIEW MIRROR
5. SET COMPASS
Normal
Ignition switch on (IG)
Pressed
MI
Compass Non-display Mode
Pressed for 3 sec.
Calibration (Step 7)
Leaving it untouched
for a while
Normal Mode
B111243E06
B057087E01
MI12 MIRROR INNER REAR VIEW MIRROR
MI REMOVAL
1. REMOVE INNER REAR VIEW MIRROR ASSEMBLY
(for TMC Made without EC Mirror)
(a) Disengage the 2 claws and the cover.
B136836
B136837
B136890
MIRROR INNER REAR VIEW MIRROR MI13
MI
B136833
B136834
B136835
MI14 MIRROR INNER REAR VIEW MIRROR
INSPECTION
1. INSPECT INNER REAR VIEW MIRROR ASSEMBLY
4 1 (a) Inspect operation of the electrochromic inner mirror.
(1) Connect the positive (+) lead from the battery
to terminal 4 and the negative (-) lead to
terminal 1.
(2) Attach black colored tape to the forward sensor
MI to prevent it from sensing.
(3) Light up the mirror with an electric light, and
check that the mirror surface changes from
bright to dark.
Standard:
Mirror surface changes from bright to
dark.
If the result is not as specified, replace the
mirror assembly.
B137080E01
INSTALLATION
1. INSTALL INNER REAR VIEW MIRROR ASSEMBLY
(for TMC Made without EC Mirror)
(a) Slide the inner rear view mirror assembly in the
direction indicated by the arrow shown in the
illustration to install it.
B136887
MIRROR INNER REAR VIEW MIRROR MI15
MI
B136836
B140444
B136835
B136834
(b) Engage the 2 claws and install the inner rear view
mirror stay holder cover as shown in the illustration.
B136841
MIRROR OUTER REAR VIEW MIRROR MI15
COMPONENTS
REMOVAL
1. REMOVE FRONT DOOR LOWER FRAME BRACKET
GARNISH (See page ED-14)
2. REMOVE OUTER REAR VIEW MIRROR ASSEMBLY
(a) Disconnect the connector.
(b) Remove the 3 nuts.
(c) Disengage the claw and remove the outer rear view
MI mirror assembly.
B136838
INSPECTION
(A)
1. INSPECT OUTER REAR VIEW MIRROR ASSEMBLY
RH
(a) Inspect outer mirror motor operation.
(C) (D) (1) Apply battery voltage and check operation of
the mirror face, as shown in the table and
illustration.
(B) Standard
Measurement Condition Specified Condition
M+ MH Battery positive (+) Terminal 5
(MV)
Turns upward (A)
H- H+ Battery negative (-) Terminal 2
(M+)
Battery positive (+) Terminal 2
MV (M+)
B137078E01 Turns downward (B)
Battery negative (-) Terminal 5
(MV)
Battery positive (+) Terminal 1
(MH)
Turns left (C)
Battery negative (-) Terminal 2
(M+)
Battery positive (+) Terminal 2
(M+)
Turns right (D)
Battery negative (-) Terminal 1
(MH)
INSTALLATION
1. INSTALL OUTER REAR VIEW MIRROR ASSEMBLY
(a) Engage the claw to install the outer rear view mirror
assembly.
(b) Install the outer rear view mirror assembly with the 3
nuts.
Torque: 5.5 N*m (56 kgf*cm, 49 in.*lbf)
(c) Connect the connector.
B136838 2. INSTALL FRONT DOOR LOWER FRAME BRACKET
GARNISH (See page ED-34)
MI18 MIRROR OUTER REAR VIEW MIRROR GLASS
COMPONENTS
TMC made:
MI
TMMK made:
B146018E01
REPLACEMENT
1. REMOVE OUTER REAR VIEW MIRROR GLASS (for
TMC Made)
(a) Push the upper part of the mirror surface and tilt it.
(b) Using a moulding remover, disengage the 2 claws at
Moulding the lower part of the outer rear view mirror, and
Remover remove the outer rear view mirror glass.
Protective Tape
B136868E01
B136869
MIRROR OUTER REAR VIEW MIRROR GLASS MI19
Protective Tape
MI
B146019E01
B146020
B136869
B136870
B146020
MI20 MIRROR OUTER REAR VIEW MIRROR GLASS
MI
B146021
MIRROR OUTER MIRROR SWITCH MI21
COMPONENTS
MI
B136891E01
MI22 MIRROR OUTER MIRROR SWITCH
REMOVAL
1. REMOVE NO. 1 INSTRUMENT PANEL SUB-
ASSEMBLY (See page IP-22)
2. REMOVE OUTER MIRROR SWITCH ASSEMBLY
(a) Disengage the 2 claws and remove the outer mirror
switch assembly.
MI
B136840
INSPECTION
1. INSPECT OUTER MIRROR SWITCH ASSEMBLY
(a) Inspect the outer mirror switch.
(1) Measure the resistance according to the
value(s) in the table below when the switch is
operated.
Standard resistance:
Select "L" on the left/right adjustment
switch
Tester Connection Switch Position Specified Condition
4-8
UP
6-7
4-7
DOWN
6-8
Below 1
5-8
LEFT
6-7
5-7
RIGHT
6-8
INSTALLATION
1. INSTALL OUTER MIRROR SWITCH ASSEMBLY
(a) Engage the 2 claws and install the outer mirror
switch assembly.
2. INSTALL NO. 1 INSTRUMENT PANEL SUB-
ASSEMBLY (See page IP-57)
MI
B136840