Professional Documents
Culture Documents
Diagrama de Autoestereo Sony CDX-GT35U PDF
Diagrama de Autoestereo Sony CDX-GT35U PDF
GT39UE
SERVICE MANUAL AEP Model
UK Model
Ver. 1.1 2010.02 CDX-GT35U/GT39U
E Model
CDX-GT35U
Russian Model
CDX-GT35U/GT39UE
Photo: CDX-GT35U
SPECIFICATIONS
General
Outputs:
NOTES ON HANDLING THE OPTICAL PICK-UP
Audio outputs terminal
BLOCK OR BASE UNIT
(sub/rear switchable)
The laser diode in the optical pick-up block may suffer electro-
Power antenna (aerial) relay control terminal
static break-down because of the potential difference generated by
Power amplifier control terminal
the charged electrostatic load, etc. on clothing and the human body.
Inputs:
During repair, pay attention to electrostatic break-down and also
Telephone ATT control terminal
use the procedure in the printed matter which is included in the
(AEP, UK, Russian model)
repair parts.
Remote controller input terminal
The flexible board is easily damaged and should be handled with
(AEP, UK, Russian model)
care.
Antenna (aerial) input terminal
AUX input jack (stereo mini jack) NOTES ON LASER DIODE EMISSION CHECK
USB signal input connector The laser beam on this model is concentrated so as to be focused
Tone controls: on the disc reflective surface by the objective lens in the optical
Low: 10 dB at 60 Hz (XPLOD) pickup block. Therefore, when checking the laser diode emission,
Mid: 10 dB at 1 kHz (XPLOD) observe from more than 30 cm away from the objective lens.
High: 10 dB at 10 kHz (XPLOD)
Power requirements: 12 V DC car battery NOTES ON CHIP COMPONENT REPLACEMENT
(negative ground (earth)) Never reuse a disconnected chip component.
Dimensions: Approx. 178 50 179 mm Notice that the minus side of a tantalum capacitor may be
(7 1/8 2 7 1/8 in.) (w/h/d) damaged by heat.
Mounting dimensions:
Approx. 182 53 162 mm TEST DISCS
(7 1/4 2 1/8 6 1/2 in.) (w/h/d) Please use the following test discs for the check on the CD
Mass: Approx. 1.2 kg (2 lb. 11 oz.) section.
Supplied accessories:
Card remote commander: RM-X151 (E, Argentina model) YEDS-18 (Part No. 3-702-101-01)
Parts for installation and connections (1 set) PATD-012 (Part No. 4-225-203-01)
CAUTION
Design and specifications are subject to change
Use of controls or adjustments or performance of procedures
without notice. other than those specified herein may result in hazardous radia-
tion exposure.
optical pick-up
2
CDX-GT35U/GT39U/GT39UE
This compact disc player is classified as a CLASS 1 LASER prod- TABLE OF CONTENTS
uct. The CLASS 1 LASER PRODUCT label is located on the ex-
terior.
1. SERVICE NOTE ...................................................... 4
2. GENERAL
Connections .................................................................... 5
3. DISASSEMBLY
3-1. Sub Panel Assy ............................................................... 8
This label is located on the bottom of the chassis. 3-2. CD Mechanism Block ..................................................... 8
3-3. Main Board ..................................................................... 9
UNLEADED SOLDER 3-4. Servo Board .................................................................... 9
Boards requiring use of unleaded solder are printed with the lead- 3-5. Chassis (T) Sub Assy ...................................................... 10
free mark (LF) indicating the solder contains no lead. 3-6. Roller Arm Assy.............................................................. 10
(Caution: Some printed circuit boards may not come printed with 3-7. Chassis (OP) Assy ........................................................... 11
the lead free mark due to their particular size) 3-8. Chucking Arm Sub Assy ................................................. 11
3-9. Sled Motor Assy.............................................................. 12
: LEAD FREE MARK 3-10. Optical Pick-up Section .................................................. 13
Unleaded solder has the following characteristics. 3-11. Optical Pick-up ............................................................... 13
Unleaded solder melts at a temperature about 40 C higher
than ordinary solder. 4. DIAGRAMS
Ordinary soldering irons can be used but the iron tip has to be 4-1. Block Diagram Main Section ..................................... 15
applied to the solder joint for a slightly longer time. 4-2. Block Diagram Display Section ................................. 16
Soldering irons using a temperature regulator should be set to 4-3. Printed Wiring Board Main Section............................ 18
about 350 C. 4-4. Schematic Diagram Main Section (1/3)...................... 19
Caution: The printed pattern (copper foil) may peel away if 4-5. Schematic Diagram Main Section (2/3)...................... 20
the heated tip is applied for too long, so be careful! 4-6. Schematic Diagram Main Section (3/3)...................... 21
Strong viscosity 4-7. Printed Wiring Boards Key Section ............................ 22
Unleaded solder is more viscous (sticky, less prone to flow) 4-8. Schematic Diagram Key Section ................................ 23
than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.
5. EXPLODED VIEWS
Usable with ordinary solder
5-1. Main Section ................................................................... 28
It is best to use only unleaded solder but unleaded solder may
5-2. Front Panel Section ......................................................... 29
also be added to ordinary solder.
5-3. CD Mechanism Section (MG-101Y-188//Q) .................. 30
3
CDX-GT35U/GT39U/GT39UE
SECTION 1
SERVICE NOTE
EXTENSION CABLE AND SERVICE POSITION
When repairing or servicing this set, connect the jig (extension
cable) as shown below.
MAIN BOARD
CN701 J-2502-076-1
SERVO BOARD
CN401
NOTE FOR REPLACEMENT OF THE USB CONNECTOR NOTE FOR REPLACEMENT OF THE SERVO BOARD
(CN902) When repairing, the complete SERVO board (Part No.
To replace the USB connector requires alignment. A-1555-002-A) should be replaced since any parts in the SERVO
1. Insert the USB connector into the front panel. board cannot be repaired.
2. Place the KEY board on the front panel and align the terminals
NOTE FOR THE 20-PIN CONNECTOR (CN901)
of the USB connector with the holes in the KEY board.
Do not use alcohol to clean the 20-pin connector (CN901) connect-
3. Solder the four terminals of the connector.
ing the front panel with the main body.
Do not touch the connector directly with your bare hand. Poor con-
tact may be caused.
KEY board
front panel
4
CDX-GT35U/GT39U/GT39UE
SECTION 2
GENERAL This section is extracted
from instruction manual.
CONNECTIONS
E model
2#! PIN CORD NOT SUPPLIED
!5$)/ /54 CAN BE SWITCHED 35"