Professional Documents
Culture Documents
Effects of Cooling Rate On The Hardenability of Chromium Containing PM Steels
Effects of Cooling Rate On The Hardenability of Chromium Containing PM Steels
Bruce Lindsley
Senior Materials Engineer
Hoeganaes Corporation
Cinnaminson, NJ 08077, USA
ABSTRACT
Two chromium containing grades, Cr-modified Ancorloy MDC and a developmental CrMnSiMo steel,
have been investigated to develop an understanding of the phase transformation behavior of these steels
during cooling. The cooling rates studied are in the range typically found in sintering furnaces. A
quantitative study to assess the hardenability of these materials has been undertaken and the results of
dilatometric, metallographic and hardness evaluations to determine the effects of cooling rate on the
various Cr containing steels are presented.
INTRODUCTION
The use of chromium and manganese in wrought steels is a result of the relatively low cost of these
elements and their effectiveness as alloying elements. Cr and Mn improve both the mechanical properties
and hardenability of low alloy steels. It would be desirable to incorporate these elements in P/M steels,
especially with the adoption of sinter hardening practices. Silicon containing steels (Ancorloy MD series)
had been developed earlier that utilized the strengthening contribution of silicon, but required high
temperature (1260 C) sintering (1,2). Two newer alloys, Cr-modified MDC and a developmental
CrMnSiMo grade, build on the advantages of the silicon containing steels. The Cr-modified MDC has
reduced Ni content and added Cr, with an overall lower alloy content than MDC. The CrMnSiMo alloy is
nickel free and utilizes the advantages of both Cr and Mn.
The hardenability of both steels is examined within the range of cooling rates typically found in
sintering furnaces.
The continuous sinter cooling transformation (CSCT) method is similar to the traditional continuous
cooling transformation (CCT) method for determining hardenability utilizing high temperature
dilatometry. The method used in this study is described by Semel (3,4) with some minor modifications.
A brief overview of the procedure follows.
Two chromium containing alloys were tested in this study, Table I. The Cr-modified MDC is
similar to MDC (4.4 wt% Ni, 0.7 wt% Si, 0.8 wt% Mo) in composition, with a lower nickel content and
the addition of chromium. The second alloy contains Cr, Mn, Si and Mo, designated CrMnSiMo. Both
alloys were prepared with 0.6 wt% added carbon. Samples, with a length and height of 11.6 mm and
thicknesses of 3.8, 6.4 and 10 mm, were pressed to a green density of 7.1 g/cm3 and sintered in a ceramic
belt furnace at 1260 C (2300 F) in a 90 vol% nitrogen 10 vol% hydrogen atmosphere. The samples
were then tempered at 650 C to soften the alloys and allow a hole to be drilled for the thermocouple in
the specimens. Individual samples were then placed in a high temperature dilatometer and heated to
1120 C (2050 F) and held for 10 minutes. Ideally, this austenitizing temperature would be the same as
the sintering temperature. However, quartz tubing, used to contain the atmosphere and hold the sample in
the dilatometer, is required for radiative cooling and cannot withstand the 1260 C sintering temperature.
The lower austenitizing temperature in the dilatometer is predicted to reduce the austenite grain size and
thereby reduce the hardenability of the alloy.
The samples were cooled to 865 C and held for 5 minutes to stabilize the temperature prior to
accelerated cooling. The samples were then cooled at different rates by changes in sample thickness,
furnace position and gas flow rate. The gas used in the dilatometer was 90 vol% helium 10 vol%
hydrogen at a flow rate of 1.4 liters/min (3 cfh), except at the highest cooling rates, when flow rates of
37 liters/min (80 cfh) and 28 liters/min (60 cfh) were used during the cooling portion of the experiment.
The cooling rate was defined as an average rate between 850 C and 315 C.
The phase transformation temperature from austenite to the low temperature phase (martensite,
bainite, and/or ferrite/cementite) was determined from a plot of temperature vs. dilation. An example of
the temperature dilation plot is shown in Figure 1. In this example, the sample was cooled at 31 C/min
and transformations were detected at 524 C, 400 C and 190 C. Above 524 C, the sample is austenitic.
120
100
80
Dilation (micron)
60
40
o
524 C
20
o o
190 C 400 C
0
-20
0 100 200 300 400 500 600 700 800 900
Temperature (C)
Figure 1. Change in sample length during cooling at 31 C/min of Cr-modified Ancorloy MDC.
A reduction in slope represents the precipitation of a lower density phase. The large change in slope at
190 C is due to martensite formation. The transformation temperature(s) were correlated to the
microstructure of the dilatometer specimens. The samples were cross-sectioned, mounted, polished and
etched using standard metallographic techniques. The fraction of different microstructures (excluding
porosity) in the samples was quantitatively determined using the point count method. The lower bainite
morphology was defined as bainite. The remaining ferrite + carbide microstructures were defined as
pearlite. Apparent hardness of the samples was measured in the center of the cross-sectioned face
opposite that used for metallography.
RESULTS
Typical chemistries of the two alloys are shown in Table I. The carbon content of each sample was
measured after dilatometry testing. The average sintered carbon content is given in the table. Carbon
contents were within 0.02 wt% of that listed. The carbon contents of the thinnest samples (3.8 mm)
contained the lowest carbon contents in this range due to a small amount of decarburization.
The development of the continuous sinter cooling transformation diagram is described by Semel (3). The
diagram is based on a linear time scale and traces of four cooling profiles along with the average cooling
rates are shown. The legend in each figure is as follows: A austenite, M martensite, B bainite, P
pearlite. The solid black lines represent the transformation start temperatures for the various
microstructures as measured in the dilatometer. The grey transformation start lines were not detected in
the dilatometer and are interpretations based on the microstructures.
167 5.0 92 8 0 74
600 128
115
3.8
3.5
85
83
15
17
0
0
74
72
A Ps
88 2.6 82 18 0 72
500 58 1.7 66 25 9 69
A+P Bs 31 0.9 51 30 19 68
400
300 A+B A+B+P
Ms
200 M+B
M+B+P o
31 C/min
100 o
177 C/min
o
128 C/min
o
88 C/min
0
0 5 10 15 20 25 30 35 40 45
Time (min)
Figure 2. CSCT Diagram for Cr-modified MDC + 0.5 wt% carbon
Figure 3. Cr-modified MDC cooled at 31 C/min. Nickel rich regions (Ni), martensite (M), bainite (B),
pearlite (P) and unresolved pearlite / upper bainite (UP) morphologies are labeled.
CrMnSiMo Hardenability
Figure 4 shows the CSCT diagram for the CrMnSiMo alloy. This alloy also has high
hardenability. A large volume fraction of martensite along with high hardnesses were found at the faster
cooling rates. The bainite transformation temperatures are similar to the Cr-modified MDC. The
martensite start temperature is higher at the fast cooling rates as compared to Cr-modified MDC, but
3
CrMnSiMo Alloy - 0.49wt% Sintered Carbon at 7.1g/cm
Continuous Cooling Transformation Diagram
900 Microstructure and Apparent Hardness
800 o
Cooling Rate
C/min o
F/sec
M
%
B
%
P
%
Hardness
HRA
700 186 5.6 97 3 0 73
Temperature (C)
158 4.7 99 1 0 74
600 128
115
3.8
3.5
87
84
13
16
0
0
74
73
A Ps
500 84
55
2.5
1.7
63
26
35
54
2
21
72
69
A+P Bs
400 33 1.0 4 51 45 64
300 Ms
A+B A+B+P
200 M M+B
M+B+P o
100 o
186 C/min
o
128 C/min
o
84 C/min
33 C/min
0
0 5 10 15 20 25 30 35 40 45
Time (min)
Figure 4. CSCT Diagram for CrMnSiMo alloy + 0.5 wt% carbon
then drops to a lower temperature at slower cooling rates. The morphology that is defined as pearlite has
a start temperature below 500 C and represents close to 50% of the microstructure at the slowest cooling
rate. At the higher cooling rates, the alloys behave similarly. Both are primarily martensitic with small
amounts of bainite. The hardness of the alloys is also similar. It is only at the slowest cooling rate that a
difference in hardness is apparent. This corresponds to a significant difference in the amount of
martensite present. In the CrMnSiMo alloy, only 4% martensite was found at a cooling rate of 33 C/min.
This may be due to the lack of admixed nickel in this alloy system. Nickel rich regions tend to form
martensite at slow cooling rates, as was seen in the Cr-modified MDC alloy.
The high pearlite content at the slowest cooling rate may be misleading. A large portion of the
microstructure identified as pearlite may in fact be upper bainite. The structure was extremely fine and
could not be resolved by light microscopy, Figure 5. Some of the structure appears to have a preferred
crystallographic orientation (packet boundaries), suggesting the structure may be bainitic. In addition,
transformation temperatures below 500 C have historically indicated bainite formation in other alloy
systems. The structure was conservatively termed pearlite in this study. Some researchers do not
distinguish between pearlite and bainite, rather use a ferrite and carbide designation. While simpler, some
information is lost about the resulting microstructure, and that convention is not used here.
It is interesting to note that high hardness can be achieved in the CrMnSiMo alloy at lower
martensite contents as compared to the Cr-modified MDC alloy. At a nominal cooling rate of 55 C/min,
both alloys have an apparent hardness of 69 HRA. The Cr-modified MDC alloy has 66% martensite
while the CrMnSiMo alloy contains only 26% martensite. The large amount of lower bainite that forms
in the CrMnSiMo alloy provides considerable strength and hardness. In addition, the unresolved ferrite +
carbide morphology will be considerably stronger than the coarser pearlite found in the Cr-modified
MDC alloy.
Figure 5. Microstructures of the CrMnSiMo alloy cooled at 33 C/min. Martensite (M), lower bainite
(B), pearlite (P) and unresolved pearlite / upper bainite (UP) are present.
Cooling Rate
The cooling rate in this study was defined as the average cooling rate between 850 C (1560 F)
and 315 C (600 F). The large range between the upper and lower temperatures may make it difficult to
determine the critical cooling rate at the time of the transformations. A preference by some researchers
for defining the start of the average cooling rate at 650 C (1200 F) exists in the literature. The
following table shows the change in average cooling rate with the different start temperatures. One can
see that using the 650 C start temperature decreases the reported cooling rate. For example, to achieve a
hardness of 72 HRA in the CrMnSiMo alloy, the cooling rate needed between 650 C and 315 C is only
65 C/min, not the 84 C/min reported in the CSCT diagram. Utilizing the range between 850 C and
315 C provides a conservative estimate in the CSCT diagram of what one can expect to find when
cooling these alloys.
Table III. Quantitative metallography of the CrMnSiMo alloy dilatometer and sintering furnace samples.
Average cooling rate between 650 C and 315 C.
Sample Type Cooling Rate % Martensite % Bainite % Pearlite
(C/min)
Dilatometer 93 84 16 0
Sinter Furnace 94 96 2 2
Dilatometer 40 25 54 21
Sinter Furnace 41 58 17 25
The continuous cooling transformation characteristics of two chromium containing alloys were studied
using the CSCT method in the cooling rate range of 186 C/min to 33 C/min. The CSCT diagrams
provide the transformation data typically found in a CCT curve along with quantitative metallographic
and apparent hardness results.
The Cr-modified MDC alloy has excellent hardenability. At the slowest cooling rate tested, the
material consisted of more than 50% martensite and had a hardness of 68 HRA (35 HRC). A maximum
hardness of 74 HRA (47 HRC) was achieved at the higher cooling rates. Pearlite formation can be
avoided at cooling rates possible in sintering furnaces, providing excellent as-sintered properties.
The CrMnSiMo alloy also has excellent hardenability at all but the slowest cooling rates tested.
The structure is predominately bainitic at slower cooling rates and martensitic at higher cooling rates.
Hardnesses of 64 HRA (27 HRC) to 74 HRA (47 HRC) were found over the range of cooling rates tested.
ACKNOWLEDGEMENTS
The author wishes to thank Fred Semel, Paul Kremus and Gerry Golin for their assistance in obtaining
and analyzing the data used in this manuscript.
REFERENCES
1. James, W.B., Causton, R.J., Baran, M.C., and Narasimhan, K.S., New High
Performance P/M Alloy Substitutes for Malleable and Ductile Cast Irons, Advances in
Powder Metallurgy & Particulate Materials, compiled by H. Ferguson and D. Whychell,
Metal Powder Industries Federation, Princeton, NJ, 2000, part 13, p.123.
2. Baran, M.C., Chawla, N., Murphy, T.F., and Narasimhan, K.S., New High Performance
P/M Alloys for Replacing Ductile Cast Irons, Advances in Powder Metallurgy &
Particulate Materials, compiled by H. Ferguson and D. Whychell, Metal Powder
Industries Federation, Princeton, NJ, 2000, part 13, p.133.
3. Semel, F. J., Cooling Rate Effects on the Metallurgical Response of a Recently Developed Sinter
Hardening Grade, Advances in Powder Metallurgy & Particulate Materials, Compliled by V.
Arnhold, C-L. Chu, W. Jandeska and H. Sanderow, Metal Powder Industries Federation,
Princeton, NJ, 2002, part 13, p. 102.
4. Semel, F. J., Ancorloy Hardenability, Advances in Powder Metallurgy & Particulate Materials,
Metal Powder Industries Federation, Princeton, NJ, 2004.