2013 SECTION Il, PART 8 5-622
SPECIFICATION FOR SEAMLESS NICKEL AND
NICKEL-COBALT ALLOY PIPE AND TUBE
CxS SB-622
ro
(Identical with ASTM Specification B622-06 except that E 527 removed from References, definition of
remainder added to Table 1, and certification has been made mandatory;)
907sB-622 2013 secrION
PART B
SPECIFICATION FOR SEAMLESS NICKEL AND
NICKEL-COBALT ALLOY PIPE AND TUBE
Ce
SB-622
(Gseticat with ASTM Speciation B 622-06 except that E 527 removed from References, debnton of remainder ade to Table 1, ed
‘cetfcation has boon made mandatory.)
1. Scope
11 This specification covers seamless pipe and tube
of nickel and nickel-cobalt alloys (UNS NI0001, UNS.
1N10242, UNS N10665, UNS N12160, UNS N10675, UNS
1N10276, UNS NO64SS, UNS NO6007, UNS NO8320, UNS
1N06975, UNS NO6002, UNS N06985, UNS NO6022,
‘UNS NO6035, UNS NO8135, UNS N06255, UNS NO60S8,
UNS NO6059, UNS NO6200, UNS NO6030, UNS NO803I,
UNS R30S56, UNS NO8535, UNS NO6250, UNS N06060,
UNS NO6230, UNS NO6686, UNS N10629, UNS N06210,
UNS 10624, and UNS R20033) as shown in Table 1
1.2. Pipe and tube shall be supplied in the solution
annealed and descaled condition, When atmosphere control
is used, descaling is not necessary.
1.3. The values stated in inch-pound units are to be
regarded as the standard. The values given in parentheses
are for information only,
1.4 This specification is limited to tubes up to and
including 3.5 in, (88.9 mm) outside diameter.
LS This standard does not purport to address all of
the safety concerns, if any, associated with its use. It is
the responsibility of the user of this standard to become
familiar with all hazards including those identified in the
‘appropriate Material Safety Data Sheet (MSDS) for this
product/material as provided by the manufacturer, 10
establish appropriate safety and health practices, and
determine the applicability of regulatory limitations prior
10 use,
2. Referenced Documents
21 ASTM Standards:
B 829 Specification for General Requirements for Nickel
and Nickel Alloys Seamless Pipe and Tube
908
E8 Test Methods for Tension Testing of Metallic Materials
3. Terminology
3A Definitions
BLL average diameter, n—the average of the maxi-
‘mum and minimum outside diameters, or the maximum
and minimum inside diameters, as determined at any eross|
section of the tube.
3.1.2 pipe, n—seamiless tube conforming to the par-
ticular dimensions commercially known as standard pipe
sizes (Appendix X2).
3.3 tube, n—a hollow product of round or any
other cross section having a continuous periphery.
General Requirements
4.1 Material furnished under this specification shall
conform to the applicable requirements of Specification B
829 unless otherwise provided herein,
S. Ordering Information
5.1 Its the responsibility of the purchaser to specify
all requirements that are necessary for the material ordered
Under this specification. Examples of such requirements
include, but are not limited to the following:
SAL Alloy (Table 1),
51.2 Dimensions:e622
2013 SECTION Il, PART B
ow pata) a |u[a])z|w fal ro | uo [remfeul a [ow [oo [rw] o J m | aa Tow | 1 | wn
+N a an s|@ s
3S wend
‘SLNBW3MIND3Y TWOIMTHD
TangvL
909