Professional Documents
Culture Documents
Electronic, Electricity, Control and Telecommunication: Technical Education
Electronic, Electricity, Control and Telecommunication: Technical Education
TC Version 2.1
280-13, Seongsu-dong 2 ga, Seongdong-gu, Seoul 133-832, Korea KS Q ISO 9001 KAB-QC-26
Features
Provision of Unified Foundation for Electric and Electronic Engineer
Utilization of Various Application Experiments with Add-On Module
Built in Signal Generator, Digital Storage Oscilloscope, Digital Multimeter and Frequency Counter
Experiments
Chapter 1. Introduction. Chapter 3. Transistor Circuit
Test 1. X-Trainer System Introduction Test 7. Transistor Characteristic
Test 2. Basic Knowledge Test 8. Transistor Switching
Test 9. MOSFET Characteristic
Chapter 2. Diode Circuit Test 10. Small Signal Common Source FET Amplifier
Test 3. Diode Characteristic Test 11. Small Signal Common Drain and Gage FET Amplifier
Test 4. Diode Rectufier
Test 5. Diode Application Circuit Chapter 4. Operational Amplifier
Test 6. Zener Diode Characteristic and Application Test 12. Basic Circuit
Test 13. Comparator & Adder
Test 14. Integrator
Test 15. Application Circuit
Specifications
Basic Module Input Power : AC 110/220 V, 50/60 Hz, DC Output : 0-12V (Variable) 5V, 12V, -12V
FND Display : 8Digits Decimal Number Indicator ( 7-Segment)
Bread Board : Socket Strip (630 hole) 3ea, Bus Stripe (100 hole) 4ea
Variable Resistor : 0-100K Push Switch: 10-Lock Switch, LED Display : 10-3 color LED Display
Toggle Switch : 2channel Toggle Switch, One Clock Pulse : H-L, L-H Clock Pulse 0.6mm jump wire
Signal Generator Output of a sine wave and a square wave , Frequency range : 1Hz ~ 20 Hz
Digital Storage 2 channel, 11 probe BNC Socket, 100 MH, 10 MHz Sampling Speed, 1M Input Impedance
Oscilloscope Vertical resolution : 8BIT, Voltage measurement range :1mv/div-5v/div
Time measurement range : 500ns/div 2s/div
Touch Screen-type menu, Auto Setup & Trigger Mode Support, AC/DC/GND input coupling
Digital Multimeter DISPLAY (LCD) : 4-Difit-Resistance : up to 40M, DC/AC Voltage : up to 600V DC/AC current : up to 10A,
Capacitance : up to 40uF, Diode check
Sound CONTINUITY (short) TEST(CONTINUITY TEST), Duty Cycle : 0.1%~99.9%
Frequency Counter DISPLAY (LCD) : 8-DIGIT Count, 15mm HIGH, DC Voltage : 200m/2V0.5%, 20/200/600v 0.8
Measurement Range : 1Hz ~ 100 MHz
GUI Program
(Interface with Computer)
Measuring equipment
Optional modules
Main Module Sub - Module Main-Module Sub-Module
Features
PLC editing module
-A fully operational ladder diagram editor that incorporates all the basic functions of PLC programming. It is used for creating and
editing PLC ladder diagrams.
-Students create logic control applications by selecting instructions from a list of functions used in PLC programming (inputs, outputs,
timers, counters and flags) and linking these instructions to variable addresses.
-Rungs
. and branches can be added to the ladder to form more complex programs. The ladder diagram can be run and fully
debugged from within the PLC editor, making programming a much easier task.
PLC simulation module
-Enables online and offline activation of the application in the HMI alone, or together with actual equipment.
-PLC simulator runs the ladder logic control program while the HMI responds accordingly.
-When offline, the PLC simulator allows the user to control the process either from the ladder diagram or the HMI.
Ladder diagrams
-Ladder diagrams can be exported and displayed as IEC 1131-3 Instruction List.
PLC training panel simulator module
-Activates the PLC simulator with the panel HMI interface.
-Allows students to run a previously programmed ladder and observe it in the training panel simulation.
HMI graphic editor module
-An interactive graphic module for creating any PLC-controlled system.
-Allows students to develop original HMI (human machine interface) applications and visualize production lines and other industrial
processes.
-Includes a number of sample HMIs, including one of the PLC training panel -Students can also create their own HMIs.
-Simple enough so that users with minimal computer or programming skills can create elaborate industrial applications.
-HMIs simulate and communicate with control equipment, both industrial PLCs and the PLC training panel.
-As the equipment is monitored and data is recorded, the HMIs reflect system logic requirements and operator requests.
Interface languages
-English, Portuguese
Functions-Simulation of sample HMI applications bundled with the software.
-Simulation of industrial PLCs, such as Allen-Bradley SLC-500 and MicroLogix and Texas Instrument TI 505 series.
-Online operation and control of applications using industrial PLCs, such as Allen-Bradley SLC-500 and MicroLogix.
-On-line graphic tracking of PLC: marks active elements; solves logic functions; displays digital and analog tracking charts for
selected elements; displays status of I/Os
Features
1) Mechatronics System Training using AVR Microprocessor
2) As control methods over 2-Wheel structured driving part, experiments of PIP Control using Tilt Sensor and
Acceleration/Deceleration Control Technique using PWM are available.
3) Experiments of various sensing and control method via diverse A/D and D/A experiments.
4) Additional various modules and functions can be attached on robust structured frame.
5) Can be used as a basic frame of vehicles.
6) Diverse applications such as crime prevention, patrol, safety, etc. are available by applying wireless vision system.
Features
* Search persons requiring salvage at the site of firing and disaster
* Guides refugees to evacuation routes, or determines whether a rescue team shall be delegated, and provides
information.
* Portable and throwing type consumptive mobile robot
* Firing point detection, poisonous gas detection, temperature measurement using sensor module
* Real-time communication is supported via image and voice transmission/receiving module
Configurations
* CMOS Camera: Environment Monitoring * Non-contact Temperature Sensor Module
* Auxiliary Wheel * Wireless Voice Transmission Module
(Camera Up-Down Angle Adjustment) * DC Motor Driving Circuit
* Electronic Compass (Robot Direction Sensing) * Communication Network
* Geared DC Motor (Motion Control, Sensor Data Communication)
(Location Movement, Posture Control of Robot) * Image Transmission Module (Wireless
* LED Illumination Communication)
(Emergency Light, Rescue Status Reporting) * Lithium Polymer Battery (7.4V 1050mhA)
* Robust Bi-Wheel Drive & Control System
Practice Items
Introduction of Fire-fighting Robot and Assistant Principle and Practice of Image Sensor
Fireman Robot * Practice of Sensor, Motor, Image Control
* Practice of Control Box Function and Control
* Practice to utilize fireman assistant robot
Specifisations
* Weight: 1.4kg(including battery)
* Dimension: 164*125*125(mm) (Length*Width*Height)
Features
Aluminum hard case structure for mobility
Applied experiments on the motors rotation characteristics
AC motor control technology using the Inverter
Interlocking experiments with Programmable Logic Controller
Training contents
Definition of Inverter
Inverter menu setup
Preparation of the Inverter before operation
Connection to the AC motor
Torque operation
Acceleration and deceleration
Forward/Reverse operation
Frequency operation
Accessaries
AC Cord: 1ea
Connection Cable: 1set
User Manual: 1ea
Features Accessaries
USB connection type ensures easy connection and high speed. - PLC Input 32 Points
Configured into basic digital contact; INPUT 32 point - PLC Output 32 Points
Power Cable
Features
Comprehension of basic production automation processes such as transfer, fabrication, classification, inspection and
storage
Convenient wiring and pipe arrangement with a label of each component such as sensors and actuators
PLC training system function (various types of sequence actions through a change in PLC control program
Counter/Timer function and motor control by PLC or without PLC (electrical method)
Aluminum profile worktable & control modules for easy mounting
Training contents
Configuration elements of factory automation system
Characteristics and principles of the object detection sensor
PLC (Programmable Logic Controller) control programming
Main processes of factory automation system (supply, fabrication, classification, storage)
Methods of DC motor control (speed, direction)
Mechanical structure and assembly for the factory automation system
Accessaries
Patch Cord (4 plug): 1set
AC Cord: 1ea
25pin cable: 2ea
Pneumatic Hose (10 meter): 1set
User Manual: 1ea
Features
HydraMotion enables the study of pneumatics principles and technology.
The software is a computer-aided design tool that teaches students.
how to design and operate hydraulic and electro-hydraulic circuits.
The software's HMI animation provides an accurate working simulation of hydraulic devices and circuits.
Users can change the default parameters of the hydraulic components, such as cylinder diameter and pump flow.
The software provides on-line graphic tracking of circuits in operation. (Requires computer interface control unit.)
The system's hoses are considered ideal and there is no pressure drop on lines drawn by the user.
.
All units are metric
Features
PneuMotion enables the study of pneumatics principles and technology.
The software is a computer-aided design tool that teaches students.
how to design and operate hydraulic and electro-hydraulic circuits.
The software's HMI animation provides an accurate working simulation of pneumatic devices and circuits.
Users can change the default parameters of the pneumatic components, such as cylinder diameter and pump flow.
The software provides on-line graphic tracking of circuits in operation. (Requires computer interface control unit.)
The system's hoses are considered ideal and there is no pressure drop on lines drawn by the user.
.
All units are metric
Feature
Hydraulics training system combines hardware and software(Option) to give students complete hands-on
experience in the design and construction of hydraulic circuits commonly used in industrial applications.
The module includes a slotted aluminum training panel with a wide assortment of industrial grade hydraulic
components.
Students can mount and configure components on the panel in order to create a variety of applications.
Students can connect different components, change physical parameters and observe system responses.
The unique combination of software and industrial equipment allows students to test and troubleshoot simulated
circuits before hardware connections are made.
As a computer aided design tool, Equipment teaches students how to design and operate hydraulic circuits.
Its HMI animation provides a working simulation of circuit operation and allows students to observe the
effectiveness of their hydraulic circuit designs.
Software features include:
Hydraulic circuit computer-aided design (CAD) tool.
Components selected from a complete component library.
Components placed on screen, resized and repositioned through point and click mouse operation.
Hydraulic connections drawn by point and click mouse operation.
Cross-section and schematic views.
Ladder diagram programming and execution in simulation mode.
Simulation of hydraulic circuits.
Sequence time diagram display in simulation mode.
Education Concept
Fundamentals of Hydraulics
Loading and Connecting Pipes to Hydraulic Components
Pressure Gauges and Comparing Changes in Pressure
Decompression circuit using to Decompression valve
Purging Air from the System
Lubricating the Pistons and Adjusting the Piston Levels
Hydraulic Components
(Flow Meter , Gear Pump, Piston Pump, Relief Valve, Oil Tank, Oil Filter)
Determining Characteristics of the Power Pack
Flow from A to B Using a Bi-directional/ Unidirectional Flow Control Valve
Speed control of Cylinder(meter-in, meter-out, bleed off)
Two step speed control circuit
Checking Route in a 4/3 Closed-Center Valve
Comparing the Power Losses of Four Flow Routes
Varying the Relief Valve Set Point Pressure
Logic Control of Hydraulics
Measuring the Flow from the Power Pack to the Valve
Measuring the Flow from the Valve to the Tank
Building a Circuit with Two Double-Acting Cylinders
Building a Circuit with Two Spring Return Cylinders
Building a Circuit with a 4/3 Open Center Valve
Time delay circuit(ON delay, OFF delay, ONE shot)
Electro-Hydraulics
Intermediate shutdown circuit of Cylinder
Manual return operate circuit of Double acting cylinder
Automatic return circuit of Double acting cylinder
Hydraulic motor control circuit and accumulator circuit
Sequential return operate circuit of Double acting cylinder
Sequence operate circuit of two Double acting cylinder
Feature
The pneumatics training systems combines hardware and software to give students complete hands-on
experience in the design and construction of pneumatic circuits commonly used in industrial applications.
The module includes a slotted aluminum training panel with a wide assortment of industrial grade
pneumatic components.
Students can mount and configure components on the panel in order to create a variety of applications.
Students can connect different components, change physical parameters and observe system responses.
The unique combination of software and industrial equipment allows students to test and troubleshoot
simulated circuits before hardware connections are made.
Understanding of Basic level function of pneumatics range
The way of one-touch lever fixed parts easily, type of aluminum profile.
Efficient use of space by fasten parts horizontally and vertically.
Application practice of all sorts of pneumatic equipment for FMS.
PNEUMATIC panel circuits can be designed and simulated by means of the PneuMotion software
( Optional item ).
Optional PneuMotion is a pneumatics CAD, simulation and operation software package.
As a computer-aided design tool, PneuMotion teaches students how to design and operate pneumatic
circuits.
Its HMI animation provides a working simulation of circuit operation and allows students to observe the
effectiveness of their pneumatic circuit designs.
Education Concept
Fundamentals of Pneumatics
Atmospheric Pressure and Vacuum and Applications of Pressure and Vacuum
The Laws of Gases
Using the Simulator and Basic Pneumatic Components
The 3/2 Push Button Valve
The 5/2 Air-operated, Air-returned Valve
The 3/2 Air-operated, Spring-returned Valve
The Single-acting Cylinder
The Roller Valve
Systems with Two Double-Acting Cylinders
Speed Control Circuit of Cylinders
Intermediate Stop Circuit of Cylinders
Logic Control of Pneumatics
The AND, OR, NOT, NAND, NOR Logic Control Circuit
Using Pneumatic Logic to Build Control Circuits
The Pneumatic ON-Delay, OFF-Delay, Self-Hold, Inter lock, One Shot Circuit
Manual return operate circuit of Double acting cylinder
Automatic return circuit of Double acting cylinder
Sequential return operate circuit of Double acting cylinder
Sequence operate circuit of two Double acting cylinder
Opposing Control Signals
Electro-Pneumatics
Building of Basic Electrical Circuit
The 5/2 Solenoid-Spring Valve and Solenoid-Solenoid Valve
Multi-Cylinder Electro-Pneumatic Systems
The Electric Relay, Timer, Counter, Magnetic Switches
Blocking Method of Main Circuit
Blocking Method of Maximum signal and Minimum signal Circuit