Professional Documents
Culture Documents
Xre3121 - VSX 416 S
Xre3121 - VSX 416 S
fm 1
Operating Instructions
Istruzioni per luso
VSX_516.fm 2
IMPORTANT
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
The lightning flash with arrowhead symbol, CAUTION: The exclamation point within an equilateral
within an equilateral triangle, is intended to TO PREVENT THE RISK OF ELECTRIC triangle is intended to alert the user to the
alert the user to the presence of uninsulated SHOCK, DO NOT REMOVE COVER (OR presence of important operating and
"dangerous voltage" within the product's BACK). NO USER-SERVICEABLE PARTS maintenance (servicing) instructions in the
enclosure that may be of sufficient INSIDE. REFER SERVICING TO QUALIFIED literature accompanying the appliance.
magnitude to constitute a risk of electric SERVICE PERSONNEL.
shock to persons.
D3-4-2-1-1_En-A
Replacement and mounting of an AC plug on the power supply cord of this unit should be performed only by qualified
service personnel.
Check for the ASTA mark or the BSI mark on the body of the fuse.
If the plug contains a removable fuse cover, you must ensure that it is refitted when the fuse is replaced. If you lose the fuse cover the plug
must not be used until a replacement cover is obtained. A replacement fuse cover can be obtained from your local dealer.
If the fitted moulded plug is unsuitable for your socket outlet, then the fuse shall be removed and the plug cut off and disposed of
safely. There is a danger of severe electrical shock if the cut off plug is inserted into any 13 amp socket.
If a new plug is to be fitted, please observe the wiring code as shown below. If in any doubt, please consult a qualified electrician.
IMPORTANT: The wires in this mains lead are coloured in accordance with the following code:
Blue : Neutral Brown : Live
As the colours of the wires in the mains lead of this appliance may not correspond with the coloured markings identifying the terminals in
your plug, proceed as follows ;
The wire which is coloured BLUE must be connected to the terminal which is marked with the
letter N or coloured BLACK.
The wire which is coloured BROWN must be connected to the terminal which is marked with the
letter L or coloured RED.
How to replace the fuse: Open the fuse compartment with a screwdriver and replace the fuse.
D3-4-2-1-2-2_B_En
WARNING
Before plugging in for the first time, read the following This product complies with the Low Voltage Directive
section carefully. (73/23/EEC, amended by 93/68/EEC), EMC Directives
(89/336/EEC, amended by 92/31/EEC and
The voltage of the available power supply differs
93/68/EEC). D3-4-2-1-9a_En
according to country or region. Be sure that the
power supply voltage of the area where this unit
will be used meets the required voltage (e.g., 230V
or 120V) written on the rear panel. D3-4-2-1-4_A_En
VSX_516.fm 3
If you want to dispose this product, do not mix it with general household waste. There is a separate collection system for used
electronic products in accordance with legislation that requires proper treatment, recovery and recycling.
Private households in the 25 member states of the EU, in Switzerland and Norway may return their used electronic products free of charge to
designated collection facilities or to a retailer (if you purchase a similar new one).
For countries not mentioned above, please contact your local authorities for the correct method of disposal.
By doing so you will ensure that your disposed product undergoes the necessary treatment, recovery and recycling and thus prevent potential
negative effects on the environment and human health. K058_En
DOWN
DOWN
Chapter 1:
English
Before you start
WARNING
Checking whats in the box
Deutsch
Do not use or store batteries in direct
Please check that you've received the following sunlight or other excessively hot place,
supplied accessories: such as inside a car or near a heater. This
AM loop antenna can cause batteries to leak, overheat,
FM wire antenna explode or catch fire. It can also reduce the
life or performance of batteries.
Franais
AA size IEC R6 dry cell batteries (to confirm
system operation) x2
Remote control
Setup microphone (VSX-516 model only) Operating range of remote
Warranty card control unit
Italiano
These operating instructions The remote control has a range of about 7
meters. It may not work properly if:
There are obstacles between the remote
Loading the batteries control and the receiver's remote sensor.
Direct sunlight or fluorescent light is
Nederlands
shining onto the remote sensor.
The receiver is located near a device that is
emitting infrared rays.
The receiver is operated simultaneously
with another infrared remote control unit. Espaol
5
En
VSX_516.fm 6
02 5 minute guide
Chapter 2:
5 minute guide
Where you place the speakers will have a big
Introduction to home theater effect on the sound. Place your speakers as
shown below for the best surround sound
Home theater refers to the use of multiple
effect. Also see Hints on speaker placement on
audio tracks to create a surround sound effect,
page 17 for more on this.
making you feel like you're in the middle of the
action or concert. The surround sound you get Center (C) Front
Right (R)
from a home theater system depends not only
on your speaker setup, but also on the source Front
Left (L)
and the sound settings of the receiver. Subwoofer (SW) Surround
Right (RS)
This receiver will automatically decode
multichannel Dolby Digital, DTS, or Dolby
Surround sources according to your speaker
Surround
setup. In most cases, you wont have to make Listening Surround Back(SB)*
position Left (LS)
changes for realistic surround sound, but
other possibilities (like listening to a CD with
* VSX-516 model only
multichannel surround sound) are explained in
Listening to your system on page 25. 3 Plug in and switch on the receiver, followed
by your DVD player, subwoofer and TV.
Make sure youve set the video input on your TV
Listening to Surround Sound to this receiver. Check the manual that came
This receiver was designed with the easiest with the TV if you dont know how to do this.
possible setup in mind, so with the following 4 Press QUICK SETUP on the front panel to
quick setup guide, you should have your specify your speaker setup, room size and
system hooked up for surround sound in no listening position.
time at all. In most cases, you can simply leave Use the MULTI JOG dial to select and ENTER
the receiver in the default settings. to confirm your selection. See Using the Quick
Be sure to complete all connections before Setup below for more on this.
connecting to an AC power source. 5 Play a DVD, and adjust the volume.
1 Connect your TV and DVD player. Make sure that DVD is showing in the
See Connecting a TV and DVD player on receivers display, indicating that the DVD
page 11 to do this. For surround sound, youll input is selected. If it isnt, press DVD on the
want to hook up using a digital connection remote to set the receiver to the DVD input.
from the DVD player to the receiver. There are several other sound options you can
2 Connect your speakers and place them for select. See Listening to your system on page 25
optimal surround sound. for more on this.1See also The System Setup
See Connecting the speakers on page 16. menu on page 31 for more setup options.
Note
1 Depending on your DVD player or source discs, you may only get digital 2 channel stereo and analog sound. In this case, the
listening mode must be set to STANDARD (it should already be setsee Listening in surround sound on page 25 if you need to
do this) if you want multichannel surround sound.
6
En
VSX_516.fm 7
5 minute guide 02
English
Using the Quick Setup subwoofer wasnt detected (VSX-516 model) for
the subwoofer setting in step 3, the following
You can use the Quick Setup to get your system
choices are available:
up and running with just a few button presses.
The receiver automatically makes the 2.0ch 3.0ch 4.0ch 5.0ch 6.0ch*
necessary settings after you have selected your Check the table below to find the speaker
Deutsch
speaker setup, room size and listening position. setup that corresponds with your system.
VSX-516 model only For a more complete
surround setup, see Automatically setting
up for surround sound (MCACC) on page 8.
If you want to make more specific settings,
Franais
refer to The System Setup menu on page 31.
Use the front panel controls for the steps below.
AUDIO/VIDEO MULTI-CHANNEL RECEIVER VSX-516
MULTI JOG
ENTER
Italiano
ADVANCED ST/DIRECT/ SIGNAL SB ch ACOUSTIC
STANDARD SURR AUTO SURR DVD/LD DVD 5.1 TV / SAT DVR / VCR AM TUNING / STATION SELECT PROCESSING EQ
LISTENING MODE
MULTI JOG
DOWN UP
Nederlands
5 Press ENTER.
1 If the receiver is off, press 6 Use the MULTI JOG dial to choose your
STANDBY/ON to turn the power on. room size.
2 Press QUICK SETUP. Depending on the distance of your speakers
from the listening position, choose between
3 Confirm your subwoofer setting. small, medium, or large (S, M or L), M being an
Espaol
VSX-416 model Use the MULTI JOG dial to average-sized room.
select YES or NO, depending on whether
youve connected a subwoofer, then press 7 Press ENTER.
ENTER. 8 Use the MULTI JOG dial to choose your
VSX-516 model SW DET flashes in the listening position.
display while the receiver checks your setup You can cycle between the following choices:
for a subwoofer. SW YES or SW NO confirms FWD If you are nearer to the front
the subwoofer check, then the display speakers than the surround speakers
prompts you to select your speaker setup.
MID If you are equal distance from the
4 Use the MULTI JOG dial to choose your front and surround speakers
speaker setup.
BACK If you are nearer to the surround
If you selected YES (VSX-416 model) or
speakers than the front speakers
subwoofer was detected (VSX-516 model) for
the subwoofer setting in step 3, the following 9 Press ENTER to confirm your setup.
choices are available: The display shows the speaker setup, room size
2.1ch 3.1ch 4.1ch 5.1ch 6.1ch* and listening position that you have selected.
7
En
VSX_516.fm 8
Chapter 3:
Quick surround sound setup
VSX-516 model only
MASTER
VOLUME
Note
1 The receiver will automatically exit the current menu after three minutes of inactivity. If you cancel the Auto MCACC Setup at
any time, the receiver automatically exits and no settings will be made.
8
En
VSX_516.fm 9
If you see an ERR message in the display, there The settings made in the Auto MCACC Setup
English
may be a problem with your mic or the speaker should give you excellent surround sound from
connections. Turn off the power, and check the your system, but it is also possible to adjust
problem indicated by the ERR message (see these settings manually using the System
below), then try the auto surround setup again. Setup menu (starting on page 31).1
ERR MIC Check microphone connection. Optionally, when you see SKIP? you can press
/ (cursor up/down) to select one of the
Deutsch
ERR Fch Check front speaker connections.
ERR Sch Check surround speaker following options then press ENTER, and use
connections. / (cursor up/down) to check the settings:
ERR SBch Check surround back speaker CHK SP Check the size and number of
connection. speakers youve connected (see page 35
for more on this)
Franais
ERR SW Make sure the subwoofer has
been switched on and volume on the CHK DIST. Check the distance of your
subwoofer is turned up. speakers from the listening position (see
page 36 for more on this)
6 When you see CHECK OK in the display, CHK LEVEL Check the overall balance of
confirm your speaker configuration. your speaker system (see page 36 for more
Italiano
Use / (cursor up/down) to check each on this)
speaker in turn. YES or NO should reflect the CHK EQ Select either ALL CH or F ALIGN
actual speakers connected. If the speaker to check the adjustments to the frequency
configuration displayed isnt correct, use / balance of your speaker system based on
(cursor left/right) to change the setting. the acoustic characteristics of your room
Nederlands
When youre finished, go to the next step. (see page 33 for more on this)
7 Select CHECK OK in the display then press 9 When youre finished, select SKIP? to go
ENTER. back to the System Setup menu.
The Auto MCACC checks the subwoofer level. Remember to disconnect the microphone
If the subwoofer output level is too high/ after completing the Auto MCACC Setup.
low, SW.VOL.DWN/SW.VOL.UP blinks in
Espaol
the display for five seconds. To exit and Other problems during Auto MCACC
check your subwoofer output level, press If the room environment is not optimal for the
SETUP or simply press ENTER when youre Auto MCACC Setup (too much background
prompted to RETRY?. noise, echo off the walls, obstacles blocking
The receiver outputs more test tones to the speakers from the microphone) the final
determine the optimum receiver settings for settings may be incorrect. Check for household
speaker setting, channel level, speaker appliances (air conditioner, fridge, fan, etc.),
distance, and Acoustic Calibration EQ. that may be affecting the environment and
switch them off if necessary.2 If there are any
8 The Auto MCACC Setup has finished!
instructions showing in the front panel display,
The front panel MCACC indicator lights to
please follow them.
show the surround settings are complete.
Note
1 Depending on the characteristics of your room, sometimes identical speakers with cone sizes of around 12cm will end up
with different size settings. You can correct the setting manually using the Speaker setting on page 35.
The subwoofer distance setting may be farther than the actual distance from the listening position. This setting should be
accurate (taking delay and room characteristics into account) and generally does not need to be changed.
2 Some older TVs may interfere with operation of the mic. You may want to switch off your TV during the Auto MCACC Setup.
9
En
VSX_516.fm 10
04 Connecting up
Chapter 4:
Connecting up
Analog audio cables
Making cable connections Use stereo RCA phono cables to connect
Make sure not to bend the cables over the top analog audio components. These cables are
of this unit (as shown in the illustration). If this typically red and white, and you should
happens, the magnetic field produced by the connect the red plugs to R (right) terminals
transformers in this unit may cause a and white plugs to L (left) terminals.
humming noise from the speakers.
Analog audio cables
Right (red)
Left (white)
Note
1 When connecting optical cables, be careful when inserting the plug not to damage the shutter protecting the optical socket.
When storing optical cable, coil loosely. The cable may be damaged if bent around sharp corners.
You can also use a standard RCA video cable for coaxial digital connections.
10
En
VSX_516.fm 11
Connecting up 04
English
Connecting a TV and DVD player
This page shows you how to connect your DVD
player and TV to the receiver.
1 Connect a coaxial digital audio output on 3 TV
your DVD player to the DIGITAL COAX 1 DIGITAL
Deutsch
AUDIO OUT
(DVD/LD) input on this receiver. ANALOG AUDIO OUT
OPTICAL VIDEO IN
Use a coaxial digital audio cable for the R L
connection.1
2 Connect the composite video output and
4
the stereo analog audio outputs2 on your
Franais
DVD player to the DVD/LD inputs on this FM UNBAL AM
75 LOOP ANTENNA
receiver. IN CD
(CD) OUT
VIDEO
If your DVD player has multichannel ASSIGNABLE IN
Italiano
DIGITAL IN TV /
SAT OUT
IN
analog outputs, see Connecting the DVD
IN
MONITOR
/LD OUT
multichannel analog outputs below for how ASSIGNABLE
DIGITAL IN
COAX
IN FRONT
DVD
5.1CH
INPUT SUB
to connect it. 2
(DVR/VCR)
IN
PLAY
CD-R
IN WOOFER
PREOUT
/ TAPE
COAX / MD
1
3 Connect the analog audio outputs from (DVD/LD)
OUT
R AUDIO L
REC
Nederlands
your TV to the TV/SAT inputs on this receiver.
This will allow you to play the sound from the
TV's built-in tuner. Use a stereo RCA phono This receiver
cable to do this. 2
1
If your TV has a built-in digital decoder, you
can also connect an optical digital audio Espaol
output from your TV to the DIGITAL OPT 1 COAXIAL R AUDIO L VIDEO OUT
DIGITAL OUT ANALOG OUT
(CD) input on this receiver. Use an optical
cable for the connection.3
4 Connect the MONITOR OUT video jack on
this receiver to a video input on your TV. DVD player
Use a standard RCA video cable to connect to
the composite video jack.
Note
1 If your DVD player only has an optical digital output, you can connect it to the optical input on this receiver using an optical
cable. When you set up the receiver you'll need to tell the receiver which input you connected the player to (see The Input Assign
menu on page 36).
2 This connection will allow you to make analog recordings from your DVD player.
3 In this case, you'll need to tell the receiver which digital input you connected the TV to (see The Input Assign menu on page 36).
11
En
VSX_516.fm 12
04 Connecting up
SURROUND
OPT
1
IN DVR /
VCR DVD 5.1CH INPUT
This receiver
(CD) OUT
VIDEO
ASSIGNABLE IN
DIGITAL IN TV /
SAT OUT FRONT
IN
IN
S R LR
DVD
/LD
MONITOR
OUT
P
ASSIGNABLE
DIGITAL IN IN FRONT E FM UNBAL AM
COAX
DVD
5.1CH 75 LOOP ANTENNA
2 PLAY
INPUT SUB
WOOFER
A A IN CD
(DVR/VCR)
IN
IN CD-R
/ TAPE
PREOUT K
COAX / MD
1 E
(DVD/LD) OUT
R L
REC R IN DVR /
AUDIO
OPT VCR
S
1
(CD) OUT
VIDEO
ASSIGNABLE IN
DIGITAL IN TV /
SAT OUT
IN
IN
DVD MONITOR
/LD OUT
ASSIGNABLE IN FRONT
DIGITAL IN DVD
COAX 5.1CH
INPUT SUB
2 PLAY WOOFER
(DVR/VCR)
IN
IN CD-R PREOUT
/ TAPE
COAX / MD
1
(DVD/LD) REC
OUT
R AUDIO L
R L CENTER R L SUB VIDEO
FRONT OUTPUT SURROUND WOOFER OUTPUT
OUTPUT OUTPUT OUTPUT
2 1
DVD/multi-channel decoder
with multi-channel analog DIGITAL OUT
output jacks
OPTICAL COAXIAL R AUDIO L VIDEO
AV OUT
Note
1 The multichannel input can only be used when DVD 5.1 ch is selected (see page 30).
2 If you've already connected your TV to the TV/SAT inputs, simply choose another input. However, you'll need to remember
which input you connected the set-top box to.
3 In this case, you'll need to tell the receiver which digital input you connected the set-top box to (see The Input Assign menu on
page 36).
12
En
VSX_516.fm 13
Connecting up 04
This receiver
English
Connecting other audio
components FM UNBAL
75
AM
LOOP ANTENNA
The number and kind of connections depends IN CD
Deutsch
(CD) OUT
VIDEO
Franais
R AUDIO L
Italiano
want to record from a digital component. Use a
stereo RCA phono cable as shown. OPTICAL COAXIAL R IN
REC
L R OUT
PLAY
L
Nederlands
The example shows an analog connection to
the CD-R/TAPE/MD analog output jack using
a stereo RCA phono cable. CD-R, MD, DAT, Tape recorder, etc.
Note
1 Note that you must connect digital components to analog audio jacks if you want to record to/from digital components (like
an MD) to/from analog components.
13
En
VSX_516.fm 14
04 Connecting up
Microsoft, Windows Media, and the Windows logo are This receiver
trademarks, or registered trademarks of Microsoft
Corporation in the United States and/or other countries.
FM UNBAL AM
75 LOOP ANTENNA
IN CD
components (CD)
ASSIGNABLE
1
DIGITAL IN
OUT
TV /
IN
VIDEO
OUT
This receiver has audio/video inputs and IN
SAT
IN
DVD
outputs suitable for connecting analog or ASSIGNABLE
DIGITAL IN IN
/LD
FRONT
DVD
MONITOR
OUT
COAX
digital video recorders, including VCRs, DVD- 2
(DVR/VCR)
PLAY
CD-R
5.1CH
INPUT
IN
SUB
WOOFER
IN PREOUT
recorders and HDD recorders. COAX
1
/ TAPE
/ MD
(DVD/LD) REC
OUT
R AUDIO L
1 Connect a set of audio/video outputs on
the recorder to the DVR/VCR AUDIO and
VIDEO inputs on this receiver. 3 2 1
Use a stereo RCA phono cable for the audio
connection and a standard RCA video cable for
the video connection.
OPTICAL COAXIAL R IN L R OUT L
REC PLAY
2 Connect a set of audio/video inputs on DIGITAL OUT AUDIO IN VIDEO IN AUDIO OUT VIDEO OUT
Note
1 If your video component doesnt have a digital audio output, omit this step. If it only has an optical digital output, you can con-
nect it to the optical input on this receiver using an optical cable. When you set up the receiver you'll need to tell the receiver
which input you connected the component to (see The Input Assign menu on page 36).
14
En
VSX_516.fm 15
Connecting up 04
English
Connecting antennas To improve FM reception
Connect the AM loop antenna and the FM wire Use a PAL connector to connect an external
antenna as shown below. To improve reception FM antenna.
and sound quality, connect external antennas
(see Using external antennas below).
Deutsch
fig. a fig. b fig. c
One-touch
PAL connector
Franais
3 FM UNBAL AM
75 coaxial cable 75 LOOP ANTENNA
5 To improve AM reception
FM UNBAL
75
AM
LOOP ANTENNA Connect a 5 to 6 meter length of vinyl-coated
4
wire to the AM antenna terminal without
disconnecting the supplied AM loop antenna.
Italiano
1 2
Outdoor
antenna
5 to 6 meters
1 Pull off the protective shields of both AM
Nederlands
antenna wires. Indoor antenna
(vinyl-coated wire)
2 Push open the tabs, then insert one wire
fully into each terminal, then release the tabs FM UNBAL AM
3 Fix the AM loop antenna to the attached For the best possible reception, suspend
horizontally outdoors.
Espaol
stand.
To fix the stand to the antenna, bend in the
direction indicated by the arrow (fig. a) then
clip the loop onto the stand (fig. b).
If you plan to mount the AM antenna to a
wall or other surface, secure the stand with
screws (fig. c) before clipping the loop to
the stand. Make sure the reception is clear.
4 Place the AM antenna on a flat surface
and in a direction giving the best reception.
5 Connect the FM wire antenna in the same
way as the AM loop antenna.
For best results, extend the FM antenna fully
and fix to a wall or door frame. Dont drape
loosely or leave coiled up.
15
En
VSX_516.fm 16
04 Connecting up
CEN- SUB
TER WOOFER
FM UNBAL AM
75 LOOP ANTENNA
IN CD
R L
SURROUND
OUT DVR / DVD 5.1CH INPUT
OPT VCR
1
(CD) IN
VIDEO
ASSIGNABLE IN
DIGITAL IN TV /
SAT OUT
FRONT SURROUND CENTER SURROUND BACK
IN
IN
S R LR L
DVD
/LD
MONITOR
OUT
P
ASSIGNABLE
DIGITAL IN IN FRONT
DVD
E
COAX 5.1CH
2 REC
INPUT SUB
WOOFER
A
(DVR/VCR)
IN
OUT CD-R
/ TAPE
PREOUT K
COAX / MD
1 E
(DVD/LD)
IN
R L
PLAY
R
AUDIO
S
VSX-416 model
Powered subwoofer
1 2 3
SW
INPUT
10 mm
VSX-516 model
1 2 3
10 mm
The illustration shows the VSX-516, but connections for the VSX-416 are the same.
16
En
VSX_516.fm 17
Connecting up 04
English
equal distances from the TV.
1 Twist exposed wire strands together.
When placing speakers near the TV, we
2 Push open the tabs and insert exposed recommend using magnetically shielded
wire. speakers to prevent possible interference,
3 Release the tabs. such as discoloration of the picture when
the TV is switched on. If you do not have
Deutsch
magnetically shielded speakers and notice
VSX-516 model discoloration of the TV picture, move the
1 Twist exposed wire strands together. speakers farther away from the TV.
Place the center speaker above or below
2 Loosen terminal and insert exposed wire.
the TV so that the sound of the center
Franais
3 Tighten terminal. channel is localized at the TV screen.
If possible, place the surround speakers
Speaker terminals slightly above ear level.
Make sure that all the bare speaker wire is Try not to place the surround speakers
twisted together and inserted fully into the further away from the listening position
Italiano
speaker terminal. If any of the bare speaker than the front and center speakers. Doing
wire is touching the back panel when you so can weaken the surround sound effect.
switch the unit on, the power may cut off as a
To achieve the best possible surround
safety measure. Use good quality speaker wire
sound, install your speakers as shown
to connect the speakers to the receiver.
below. Be sure all speakers are installed
Nederlands
securely to prevent accidents and improve
Caution sound quality.
These speaker terminals carry
HAZARDOUS LIVE voltage. To prevent Caution
the risk of electric shock when connecting
If you choose to install the center speaker
or disconnecting the speaker cables,
Espaol
on top of the TV, be sure to secure it with
disconnect the power cord before touching
putty, or by other suitable means, to reduce
any uninsulated parts.
the risk of damage or injury resulting from
the speaker falling from the TV in the event
Hints on speaker placement of external shocks such as earthquakes.
Speakers are usually designed with a
particular placement in mind. Some are Make sure no exposed speaker wire is
designed to be floorstanding, while others touching the rear panel, this may cause the
should be placed on stands to sound their best. receiver to turn off automatically.
Some should be placed near a wall; others
should be placed away from walls. We have
provided a few tips on getting the best sound
from your speakers (following), but you should
also follow the guidelines on placement that
the speaker manufacturer provided with your
particular speakers to get the most out of
them.
17
En
VSX_516.fm 18
04 Connecting up
Subwoofer
Surround Surround
left right
Listening position
Front Front
left Center right
Subwoofer
Surround Surround
left right
Listening position
Note
1 VSX-416 model only Follow the speaker placement diagrams, disregarding the surround back speakers.
18
En
VSX_516.fm 19
Chapter 5:
English
Controls and displays
Front panel
Deutsch
Illustration shows the VSX-516 model
1 2 3 4 5 6 7 8
AUDIO/VIDEO MULTI-CHANNEL RECEIVER VSX-516
SIGNAL SB ch ACOUSTIC
Franais
MULTI JOG
ENTER SELECT PROCESSING EQ
STANDARD
ADVANCED ST/DIRECT/
SURR
LISTENING MODE
AUTO SURR DVD/LD DVD 5.1 TV/SAT DVR /VCR CD CD-R / TAPE / MD USB FM AM TUNING / STATION
SIGNAL
SELECT
SB ch
PROCESSING
ACOUSTIC
EQ
VSX-516 model
EON PTY MIDNIGHT/ SPEAKER MASTER
STANDBY/ON
MODE SEARCH LOUDNESS IMPEDANCE
USB MCACC
VOLUME
6 9 10
SETUP MIC
PHONES TUNER QUICK
MUTE EDIT TONE SETUP SETUP RETURN
Italiano
MULTI JOG SIGNAL VSB DIALOGUE
DOWN UP
SELECT MODE ENHANCEMENT
11 12 13 VSX-416 model
14 17 18 19 20
Nederlands
ADVANCED ST/DIRECT/ EON PTY MIDNIGHT/ SPEAKER
STANDARD SURR AUTO SURR MODE SEARCH LOUDNESS IMPEDANCE
LISTENING MODE
15 21 22 23 24 25
STANDBY/ON
TUNER QUICK
PHONES MUTE EDIT TONE SETUP SETUP RETURN
16
Espaol
MULTI JOG
19
En
VSX_516.fm 20
20
En
VSX_516.fm 21
English
Display
Illustration shows the VSX-516 model
1 2 3 4 5 6 7 8 9 10 11 12 13
EON [L] 6
Deutsch
RDS [C]
SP A [R]
[Rs ] 0
[SBR]
[SB L ]
[Ls ]
6
Franais
14 15 16 17 18 19 20 21 22 23
Italiano
Digital multichannel signal.
AUTO
Lights when AUTO signal select is on. 4 2 PRO LOGIC IIx (VSX-516 model) /
2 PRO LOGIC II (VSX-416 model)
SB (VSX-516 model only) When the (STANDARD) Pro Logic II mode
Depending on the source, this lights when of the receiver is on, 2 PRO LOGIC II
Nederlands
a signal with surround back channel lights to indicate Pro Logic II decoding. 2
encoding is detected. PRO LOGIC IIx lights to indicate Pro Logic
DIGITAL IIx decoding (see Listening in surround
Lights when a digital audio signal is sound on page 25 for more on this).
detected. 5 VIR.SB Espaol
DTS Lights during Virtual surround back
Lights when a source with DTS encoded processing (page 28).
audio signals is detected. 6 DIRECT
2 DIGITAL Lights when source direct playback is in use.
Lights when a Dolby Digital encoded Direct playback bypasses the tone controls for
signal is detected. the most accurate reproduction of a source.
21
En
05_controls_displays.fm 22
USB
8
13 Sound Retriever indicators (VSX-516 model CD CD-R FM AM
only) MIDNIGHT/
STANDARD ADV.SURR STEREO LOUDNESS
2
Light when the Sound Retriever is switched on
TOP MENU MENU
(page 30). 3 9
SETUP DIALOG E
14 Character display ENTER ONE
10
TOUCH
TUNER EDIT COPY
18 MIDNIGHT RECEIVER
Lights during Midnight listening (page 29).
19 D.E.
Lights when Dialog Enhancement (DIALOG E)
is switched on (page 29).
22
En
VSX_516.fm 23
1 RECEIVER LEVEL +/
English
Switches the receiver between standby and on. Use to adjust the effect and channel levels.
2 Listening mode buttons ACOUSTIC EQ* (SHIFT +) (VSX-516 model
STANDARD only)
Press for Standard decoding and to switch Press to select an Acoustic Calibration EQ
between 2Pro Logic II and (VSX-516 model setting (page 27).
Deutsch
only) Neo:6 options (page 25). MUTE
ADV.SURR Mutes/unmutes the sound.
Switches between the various surround 6 SHIFT
modes (page 26). Press to access the boxed commands (above
the buttons) on the remote. These buttons are
Franais
STEREO
Switches between direct and stereo marked with an asterisk (* ) in this section.
playback (page 27). Also selects the Auto 7 SLEEP
Surround mode(Auto playback on page 25). Press to change the amount of time before
MIDNIGHT/LOUDNESS the receiver switches into standby (30 min
60 min 90 min Off). You can check
Italiano
Switches to Midnight or Loudness
listening (page 29). the remaining sleep time at any time by
pressing SLEEP once.
3 TOP MENU
Displays the disc top menu of a DVD. DIMMER
Dims or brightens the display.
SETUP
Nederlands
Press to access the System Setup menu ANALOG ATT
(page 31). Attenuates (lowers) the level of an analog
input signal to prevent distortion.
4 TUNER EDIT*
8 INPUT SELECTOR buttons
Memorizes/names stations for recall
Press to select an input source.
(page 38). Also functions as the SETUP
Espaol
button for DVD/DVR units. DVD/DVR
Press to use the remote DVD/DVR
S. RETRIEVER
controls.
Press to restore CD quality sound to
compressed audio sources (page 30). RECEIVER
Use to switch to the receiver controls on
5 RECEIVER CONTROL buttons
the remote control. Use when setting up
VOLUME +/ surround sound for the receiver (page 31).
Use to set the listening volume.
9 MENU
EFFECT/CH SEL Displays the disc menu of DVD-Video
Press repeatedly to select a channel, then discs.
use LEVEL +/ to adjust the level (page 36).
Also adjusts the level of the Advanced DIALOG E
Surround effects as well as Dolby Pro Logic Use to make dialog stand out when
IIx Music and Neo:6 Music parameters watching TV or a movie (page 29).
(page 26). You can then use the LEVEL +/
buttons to make these adjustments.
23
En
05_controls_displays.fm 24
24
En
06_playing_sources.fm 25
Chapter 6:
English
Listening to your system
VSX-516 only If you connected surround back
Important speaker, see also Using surround back channel
Deutsch
Certain features explained in this section processing on page 28.
will not be possible depending on the CD CD-R FM AM
source (for example, PCM 88.2 kHz / 96 MIDNIGHT/
STANDARD ADV.SURR STEREO LOUDNESS
kHz, DTS 96 kHz (24 bit) or WMA 9 Pro TOP MENU MENU
sources).
Franais
While listening to a source, press STAN-
DARD.
If the source is Dolby Digital, DTS, or Dolby
Auto playback Surround encoded, the proper decoding
The simplest, most direct listening option is the format will automatically be selected and
Auto Surround feature. With this, the receiver
shows in the display.2
Italiano
automatically detects what kind of source
youre playing and selects multichannel or With two channel sources, press STANDARD
stereo playback as necessary.1 repeatedly to select from3:
CD CD-R FM AM
2 Pro Logic II MOVIE Up to 5.1 channel
MIDNIGHT/
STANDARD ADV.SURR STEREO LOUDNESS sound, especially suited to movie sources
Nederlands
TOP MENU MENU 2 Pro Logic II MUSIC Up to 5.1 channel
sound, especially suited to music sources
While listening to a source, press
STEREO for auto playback of a source. 2 PRO LOGIC 4.1 channel surround
Press repeatedly until AUTOSURR. shows sound
briefly in the display (it will then show the VSX-516 model only:
decoding or playback format). Check the
Espaol
2 Pro Logic IIx MOVIE Up to 6.1
digital format indicators in the display to see channel sound, especially suited to movie
how the source is being processed. sources
2 Pro Logic IIx MUSIC Up to 6.1
channel sound, especially suited to music
Listening in surround sound sources
Using this receiver, you can listen to any 2 Pro Logic IIx GAME Up to 6.1
source in surround sound. However, the channel sound, especially suited for video
options available will depend on your speaker games
setup and the type of source youre listening to.
Note
1 VSX-516 model only Stereo surround (matrix) formats are decoded accordingly using Neo:6 CINEMA or 2 Pro Logic IIx
MOVIE (see Listening in surround sound above for more on these decoding formats).
The Auto Surround feature is canceled if you connect headphones or select the multichannel analog inputs.
2 VSX-516 model only If surround back channel processing (page 27) is switched to OFF, or the surround back speaker is set
to NO (page 35), 2 Pro Logic IIx becomes 2 Pro Logic II (5.1 channel sound).
3 When listening to 2-channel sources in Dolby Pro Logic II(x) Music mode, there are three further parameters you can adjust:
Center Width, Dimension, and Panorama. See Setting the effect options below to adjust them.
25
En
VSX_516.fm 26
2 PRO LOGIC 4.1 channel surround 6-STEREO (VSX-516 model only) Gives
sound multichannel sound to a stereo source,
Neo:6 CINEMA 6.1 channel sound, using all of your speakers.
especially suited to movie sources VIR. SURR A virtual surround effect using
just the subwoofer and front speakers.
Neo:6 MUSIC1 6.1 channel sound, espe-
cially suited to music sources EX POWER (VSX-416 model only) Select
when using the surround speakers in addi-
VSX-516 model only With multichannel tion to the front speakers (see the diagram
sources, if you have connected surround back on page 18 for the Extra Power mode
speaker and have selected SB ON, you can speaker setup).
select (according to format):
PHONESUR. Creates the effect of overall
2 Pro Logic IIx MUSIC See above surround with headphones.
Dolby Digital EX Creates surround back
channel sound for 5.1 channel sources and Setting the effect options
provides pure decoding for 6.1 channel When using surround effects, there are a
sources (like Dolby Digital Surround EX) number of settings you can adjust.
DTS-ES Allows you to hear 6.1 channel
1 Press EFFECT/CH SEL repeatedly to select
playback with DTS encoded sources
the setting you want to adjust.
Using the Advanced surround effects Depending on the current status / mode of the
The Advanced surround feature creates a receiver, certain options may not appear.
variety of surround effects. Try different modes Check the table below for notes on this.
with various soundtracks to see which you like.2 VSX-416 model only From the options
below, only the EFFECT parameter is
CD CD-R FM AM
MIDNIGHT/
STANDARD ADV.SURR STEREO LOUDNESS
available.
TOP MENU MENU 2 Use the LEVEL +/ buttons to set it as
necessary.
Press ADV.SURR repeatedly to select a See the table below for the options available for
listening mode. each setting. The defaults, if not stated, are
ADV. MOVIE Suitable for movie sources. listed in bold.
ADV. MUSIC Suitable for music sources.
TV SURR. Provides surround sound for
both mono and stereo TV sources.
SPORTS Suitable for sports programs.
ADV. GAME Suitable for video games.
EXPANDED Simulates multichannel
surround sound for two-channel sources.3
Note
1 With 2-channel sources in Neo:6 Music mode, you can adjust the center image effect (see Setting the effect options below).
2 If you press ADV.SURR with the headphones connected, PHONES SURROUND will automatically be selected.
Depending on the source and the sound mode you have selected, you may not get sound from the surround back speaker
in your setup. For more on this, refer to Using surround back channel processing on page 28.
When an Advanced Surround listening mode is selected, the effect level can be adjusted using the EFFECT parameter in
Setting the effect options below.
3 Use with Dolby Pro Logic for a stereo surround effect (stereo field is wider than Standard modes with Dolby Digital sources).
26
En
06_playing_sources.fm 27
3 Press EFFECT/CH SEL again to adjust Dolby Digital, DTS and WMA9 Pro multi-
English
other settings. channel sources are downmixed to stereo.
Deutsch
only when wider (higher settings) or While listening to a source, press STEREO
using a cen- narrower (lower settings). for stereo playback.
ter speaker)
Press repeatedly to switch between:
Dimensiona Adjusts the surround sound 3 to +3 STEREO The audio is heard with your
balance from front to back, Default: 0
surround settings and you can still use the
making the sound more distant
Franais
(minus settings), or more Midnight, Loudness, and Tone functions.
forward (positive settings). DIRECT Bypass all effects and surround
OFF
settings so that the audio remains as close
Panoramaa Extends the front stereo image
to include surround speakers to the source audio signal as possible.1
for a wraparound effect. ON
AUTO SURR. See Auto playback on
Italiano
Center Adjusts the center image to 0 to 10 page 25 for more on this.
Imageb create a wider stereo effect with Default: 3
(Applicable vocals. Adjust the effect from 0
only when (all center channel sent to front
using a cen- right and left speakers) to 10 Listening with Acoustic
ter speaker) (center channel sent to the
Calibration EQ
Nederlands
center speaker only).
VSX-516 model only
Effect Sets the effect level for the 10 to 90
currently selected Advanced Default setting: OFF / ALL CH (after the
Surround mode (each mode Auto MCACC Setup or EQ Auto Setting)
can be set separately).
You can listen to sources using the Acoustic
a Only available with 2ch sources in Dolby Pro Logic IIx Mu- Calibration Equalization set in Automatically
Espaol
sic mode. setting up for surround sound (MCACC) on
b Only available with 2ch sources in Neo:6 Music mode.
page 8 or Acoustic Calibration EQ on page 33.
Refer to these pages for more on Acoustic
Calibration Equalization.
Listening in stereo S.RETRIEVER RETURN
hear the source through just the front left and HDD DVD
MUTE
DVD/DVR SUBTITLE
right speakers (and possibly your subwoofer CH CH
Note
1 If you switch on Midnight listening, Loudness, Dialog Enhancement, the Sound Retriever or the Tone controls when DIRECT
is selected, the receiver automatically switches to STEREO.
27
En
VSX_516.fm 28
28
En
VSX_516.fm 29
with no surround back channel information, or VSB ON Virtual Surround Back is always
English
if the material sounds better in the format (for used (for example, on 5.1 encoded
example, 5.1) for which it was originally material)
encoded, you can have the receiver only apply VSB AUTO (VSX-516 model only) Virtual
this effect to 6.1 encoded sources like Dolby Surround Back is automatically applied to
Digital EX or DTS-ES.1 6.1 encoded sources (for example, Dolby
VSX-516 model only The table indicates when Digital EX or DTS-ES)
Deutsch
you will hear the virtual surround back channel VSB OFF Virtual Surround Back mode is
( =Sound plays through surround speaker). switched off
Press SB ch (SB ch PROCESSING)/ VSB
MODE to select a virtual surround back
channel option.
Franais
Each press cycles through the following:
SBch Standard
Processing / Advanced
Type of source Multichannel Stereo sources
Virtual SB surround
mode sources 2 Pro Logic II x 2 Pro Logic Neo:6
Italiano
Dolby Digital EX/DTS-ES/ ON a
WMA9 Pro encoded
multichannel sources with AUTO a
6.1ch surround
Dolby Digital/DTS/WMA9 Pro ON a
encoded multichannel
Nederlands
sources AUTO a
29
En
VSX_516.fm 30
Note
1 The Sound Retriever is only applicable to 2-channel sources.
2 During playback from the multichannel inputs, you cant use any of the sound features/modes and only the volume and chan-
nel levels can be set.
30
En
VSX_516.fm 31
Chapter 7:
English
The System Setup menu
Using the System Setup menu Manual MCACC speaker setup
Deutsch
The following section shows you how to make VSX-516 model only
detailed settings to specify how youre using You can use the settings in the Manual MCACC
the receiver. It also explains how to fine-tune setup menu to make detailed adjustments
individual speaker system settings. when youre more familiar with the system.
TOP MENU MENU Before making these settings, you should have
Franais
RECEIVER SLEEP DIMMER ANALOG ATT
SETUP DIALOG E already completed Automatically setting up for
INPUT SELECTOR
DVD 5.1
Italiano
2 Use / to select the setting you want to Important
adjust then press ENTER.
A. MCACC (VSX-516 only) This is a quick For some of the settings below, youll have
and effective automatic surround setup to connect the setup microphone to the
front panel and place it about ear level at
Nederlands
(see Automatically setting up for surround
sound (MCACC) on page 8). your normal listening position. See
Automatically setting up for surround
M. MCACC (VSX-516 only) Fine tune your sound (MCACC) on page 8 if youre unsure
speaker settings and customize the how to do this. Also see Other problems
Acoustic Calibration EQ (see Manual during Auto MCACC on page 9 for notes
MCACC speaker setup below). regarding high background noise levels
Espaol
SP SETUP Specify the size, number, and other possible interference.
distance and overall balance of the If youre using a subwoofer, switch it on
speakers youve connected (see Manual and turn up the volume to the middle
MCACC speaker setup below). position.
IN ASSIG. Specify what youve connected
to the digital and component video inputs 1 Select M. MCACC from the System Setup
(see The Input Assign menu on page 36). menu.
See Using the System Setup menu above if
OTHER Make customized settings to youre not already at this menu.
reflect how you are using the receiver (see
The Other setup menu on page 37). 2 Select the setting you want to adjust.
If youre doing this for the first time, you might
want to make these settings in order.
CH LEVEL Make fine adjustments to the
overall balance of your speaker system (see
Fine Channel Level below).
31
En
VSX_516.fm 32
SP DISTN. Make precise delay settings 2 Use / to select each channel in turn
for your speaker system (see Fine Channel and adjust the levels (+/ 10 dB) as necessary.
Distance below). Use / to adjust the volume of the selected
The last five settings are specifically for speaker to match the reference speaker. When
customizing the parameters explained in it sounds like both tones are the same volume,
Acoustic Calibration EQ on page 33: press (cursor down) to continue to the next
channel.
EQ A. SET Measure the acoustic
characteristics of your room and For comparison purposes, the reference
automatically adjust the frequency balance speaker will change depending on which
of your speaker system (see Setting the speaker you select.
Acoustic Calibration EQ automatically on If you want to go back and adjust a
page 33). channel, simply use / to select it.
EQ COPY Copy Acoustic Calibration EQ 3 When you're finished, press RETURN.
settings for manual adjustment (see You will return to the Manual MCACC setup
Copying your Acoustic Calibration EQ menu.
settings on page 33).
C1 ADJ/C2 ADJ Make detailed manual Fine Speaker Distance
adjustments to your custom Acoustic Default setting: 3 m (all channels)
Calibration EQ settings (see Setting the
Acoustic Calibration EQ manually on For proper sound depth and separation with
page 34). your system, it is necessary to add a slight bit
of delay to some speakers so that all sounds
EQ CHECK Check the ALL CH, F. ALIGN will arrive at the listening position at the same
and custom settings (see Checking your time. The following setting can help you make
Acoustic Calibration EQ settings on detailed adjustments that you may not achieve
page 34). using the Automatically setting up for surround
Fine Channel Level sound (MCACC) on page 8.
Default setting: 0dB (all channels) 1 Select SP DISTN. from the Manual
You can achieve better surround sound by MCACC setup menu.
properly adjusting the overall balance of your
2 Use / to adjust the distance of the
speaker system. The following setting can help
left channel from the listening position then
you make detailed adjustments that you may
press ENTER.
not achieve using the Automatically setting up
for surround sound (MCACC) on page 8. 3 Use / to select each channel in turn
and adjust the distance as necessary.
1 Select CH LEVEL from the Manual
Use / to adjust the delay of the selected
MCACC setup menu.
speaker to match the reference speaker. The
Youll hear test tones from each speaker in
delay is measured in terms of speaker distance
turn. Since the left speaker is the main
from 0.1 to 9.0 meters.
reference speaker, the level is fixed.
Listen to the reference speaker and use it to
Caution measure the target channel. From the listening
position, face the two speakers with your arms
The test tones used in the System Setup
outstretched pointing at each speaker.
are output at high volume (the volume
increases to 18 dB automatically).
32
En
VSX_516.fm 33
Try to make the two tones sound as if they are 1 Select EQ A. SET from the Manual
English
arriving simultaneously at a position slightly in MCACC setup menu.
front of you and between your arm span. Make sure the microphone is connected.
If youre using a subwoofer, it is
automatically detected every time you
switch on the system. Make sure it is on
and the volume is at the middle position.
Deutsch
See Other problems during Auto MCACC on
page 9 for notes regarding high
When it sounds like the delay settings are
background noise levels and other possible
matched up, press (cursor down) to confirm
interference.
and continue to the next channel.
Franais
For comparison purposes, the reference 2 Wait for the EQ Auto Setup to finish.
speaker will change depending on which As the receiver outputs test tones, the
speaker you select. frequency balance is adjusted automatically
for the following settings:
If you want to go back and adjust a
channel, simply use / to select it. A. CH All Channel Adjust is a flat setting
where all the speakers are set individually
Italiano
4 When you're finished, press RETURN. so no special weighting is given to any one
You will return to the Manual MCACC setup channel.
menu.
F.ALG Front Align Adjust balances the
overall sound so that all speakers are set in
Acoustic Calibration EQ accordance with the front speaker settings
Nederlands
Acoustic Calibration Equalization is a kind of (no equalization is applied to the front left
room equalizer for your speakers (excluding and right channels).
the subwoofer). It works by measuring the
acoustic characteristics of your room and You will return to the Acoustic Cal EQ setup
neutralizing the ambient characteristics that menu after the Acoustic Calibration
can color the original source material. This Equalization is set. Espaol
provides a flat equalization setting. If youre
not satisfied with the automatic adjustment, Copying your Acoustic Calibration EQ
you can also adjust these settings manually to settings
get a frequency balance that suits your tastes. If you want to manually adjust the Acoustic
Calibration EQ (see Setting the Acoustic
Setting the Acoustic Calibration EQ Calibration EQ manually below), we
automatically recommend copying the A. CH or the F.ALG
If you have already completed Automatically settings from the EQ A. SET setup above (or
setting up for surround sound (MCACC) on from Automatically setting up for surround
page 8, A. CH ADJ and F.ALG ADJ (below) sound (MCACC) on page 8) to one of the
should already be set. Therefore, if you want to custom (C1 or C2) settings. Instead of just a flat
adjust your settings manually, you can skip to EQ curve, this will give you a reference point
Setting the Acoustic Calibration EQ manually from which to start.
below. 1 Select EQ COPY from the Manual MCACC
setup menu.
33
En
VSX_516.fm 34
2 Use / to select C1 or C2 then use the 3 Use / to select the channel you want
/ buttons to select the setting you want and adjust to your liking.
to copy. Use the / buttons to select the frequency
You can also copy from one custom setting and / to boost or cut the EQ. When youre
to another. For more on the A. CH and finished, use the / buttons to select the
F.ALG settings, see Setting the Acoustic channel display (for example R EQ for the right
Calibration EQ automatically above. channel or SB EQ for the surround back
channel) then / to proceed to the next
3 Use / to select COPY? YES to copy
channel.
and confirm.
You can also use / to select COPY? NO to The front speakers cant be adjusted if you
cancel. selected F.ALG ADJ.
The OVER! indicator shows in the display if
Setting the Acoustic Calibration EQ the frequency adjustment is too drastic
manually and might distort. If this happens, bring the
Before manually adjusting the Acoustic level down until OVER! disappears from
Calibration EQ, we recommend copying the A. the display.
CH or the F.ALG settings from the auto setup
above (or from Automatically setting up for Tip
surround sound (MCACC) on page 8) to one of
the custom settings. Instead of just a flat EQ Changing the frequency curve of one
curve, this will give you a reference point from channel too drastically will affect the
which to start (see Copying your Acoustic overall balance. If the speaker balance
Calibration EQ settings above for how to do seems uneven, you can raise or lower
this). channel levels using test tones with the
trim band (TRM shows in the display).
1 Select C1 ADJ or C2 ADJ from the Use / to select TRM then use / to
Manual MCACC setup menu. raise or lower the channel level for the
2 Use / and ENTER to select which current speaker.
method you want to use to adjust the overall 4 When you're finished, press RETURN.
frequency balance. Press RETURN once more to go back to the
It is best to choose whichever one you copied Manual MCACC setup menu.
to the custom setting in Copying your Acoustic
Calibration EQ settings above. Checking your Acoustic Calibration EQ
A. CH ADJ All the speakers can be set settings
independently so no special weighting is After you have completed an automatic or
given to any one channel. When adjusting, manual Acoustic Calibration EQ adjustment,
test tones will sound for each individual you can check the ALL CH, F.ALIGN and
channel. CUSTOM1/2 settings in the display.
F.ALG ADJ Speakers are set in
1 Select EQ CHECK from the Manual
accordance with the front speaker
MCACC setup menu.
settings. The sound of the test tone will
alternate between the left front (reference) 2 Use / and ENTER to select the setting
speaker and the target speaker. you want to check.
It is useful to do this while a source is
playing so you can compare settings.
34
En
VSX_516.fm 35
3 Use / to select the channel you want, 1 Select SP SET from the SP SETUP menu.
using / to check the settings.
English
2 Use / to choose the speaker(s) that
The MCACC channel EQ indicators in the front
you want to set then select a speaker size.
panel display will light accordingly.
Use / to select the size (and number) of
4 When you're finished, press RETURN. each of the following speakers:
You will return to the Manual MCACC setup menu. Front (F) Select LARGE if your front
Deutsch
speakers reproduce bass frequencies
effectively, or if you didnt connect a
Manual speaker setup subwoofer. Select SMALL to send the bass
These settings optimize surround sound frequencies to the subwoofer.1
performance (if youre satisfied with the settings
Center (C) Select LARGE if your center
made in Using the Quick Setup on page 7 or (VSX-
Franais
speaker reproduces bass frequencies
516 only) Automatically setting up for surround
effectively, or select SMALL to send bass
sound (MCACC) on page 8, adjustment may not
frequencies to the other speakers or
be necessary). You only need to make these
subwoofer. If you didnt connect a center
settings once (unless you change the placement
speaker, choose NO (the center channel is
of your current speaker system or add new
sent to the front speakers).
Italiano
speakers).
Surround (S) Select LARGE if your
1 Select SP SETUP from the System Setup surround speakers reproduce bass
menu. frequencies effectively. Select SMALL to
2 Use / to select the setting you want to send bass frequencies to the other
adjust then press ENTER. speakers or subwoofer. If you didnt
Nederlands
SP SET Specify size / number of speakers connect surround speakers choose NO
connected (see Speaker setting below). (the sound of the surround channels is
X.OVER Specify which frequencies will sent to the front speakers or a subwoofer).
be sent to the subwoofer (see Crossover Surround Back (SB) Select LARGE if your
network below). surround back speaker reproduce bass
frequencies effectively. Select SMALL to
Espaol
CH LEVEL Adjust overall balance of your
speaker system (see Channel level below). send bass frequencies to the other speakers
or subwoofer. If you didnt connect
SP DISTN. Specify the distance of your
speakers from the listening position (see surround back speaker choose NO.2
Speaker Distance below). Subwoofer (SW) LFE signals and bass
frequencies of channels set to SMALL are
3 Press RETURN after making the
output from the subwoofer when YES is
adjustments necessary for each setting.
selected. Choose the PLUS setting if you
want the subwoofer to output bass sound
Speaker setting continuously or you want deeper bass (the
Use this setting to specify your speaker bass frequencies that would normally
configuration (size, number of speakers).
Note
1 If you select SMALL for the front speakers the subwoofer is fixed to YES. Also, the center, surround, and surround back speak-
er cant be set to LARGE if the front speakers are set to SMALL. In this case, all bass frequencies are sent to the subwoofer.
2 If the surround speakers are set to NO, the surround back speaker will automatically be set to NO.
If you select one surround back speaker only, make sure that speaker is hooked up to the left surround back terminal.
35
En
VSX_516.fm 36
come out the front and center speakers are 4 Adjust the level of each channel using /.
also routed to the subwoofer).1 If you did If you selected T. TONE M., use / to switch
not connect a subwoofer choose NO (the speakers.
bass is output from other speakers). The T. TONE A. setup outputs test tones in the
following order (depends on speaker settings):
Crossover network L C R RS SB* LS SW
Default setting: 100Hz
*VSX-516 model only
This setting decides the cutoff between bass
Adjust the level of each speaker as the test
sounds playing back from the speakers
selected as LARGE, or the subwoofer, and bass tone is emitted.4
sounds playing back from those selected as
Speaker Distance
SMALL.2 It also decides where the cutoff will
For good sound depth and separation from
be for bass sounds in the LFE channel.
your system, you need to specify the distance
1 Select X.OVER from the SP SETUP menu. of your speakers from the listening position.5
2 Use / to choose the frequency cutoff The receiver can then add the proper delay
point. needed for effective surround sound.
Frequencies below the cutoff point will be sent 1 Select SP DISTN. from the SP SETUP menu.
to the subwoofer (or LARGE speakers).
2 Use / to choose the speaker that you
Channel level want then set the distance.
Use / to adjust the distance of each
Using these settings, you can adjust the overall
speaker (in 0.1 meter increments).
balance of your speaker system.
1 Select CH LEVEL from the SP SETUP menu.
2 Use / to select a setup option. The Input Assign menu
T. TONE M. Move the test tone manually You only need to make settings in the Input
from speaker to speaker and adjust Assign menu if you didnt hook up your digital
individual channel levels. equipment according to the default settings for
T. TONE A. Adjust channel levels as the the digital inputs.
test tone moves from speaker to speaker Assigning the digital inputs
automatically.
Default settings:
3 Confirm your selected setup option. COAX 1 (coaxial) DVD
The test tones will start after you press ENTER.3 COAX 2 (coaxial) DVR
OPT 1 (optical) CD
Note
1 If you cant get good bass results, listen to the bass response with the subwoofer set to PLUS and YES or the front speakers
set to LARGE and SMALL alternatively and let your ears judge which sounds best. If youre having problems, the easiest option
is to route all the bass sounds to the subwoofer by selecting SMALL for the front speakers.
2 For more on selecting the speaker sizes, see Speaker setting above.
3 After the volume increases to the reference level, test tones will be output.
4 If you are using a Sound Pressure Level (SPL) meter, take the readings from your main listening position and adjust the level
of each speaker to 75 dB SPL (C-weighting/slow reading).
The subwoofer test tone is output at low volumes. You may need to adjust the level after testing with an actual soundtrack.
You can change the channel levels at any time by using EFFECT/CH SEL and +/ on the remote control. You can set two
channel levels: one for DVD 5.1 and one for the listening modes.
5 For best surround sound, make sure the surround back speaker is the same distance from the listening position.
36
En
VSX_516.fm 37
You only need to do this if you didnt connect LFE ATT Set the attenuator level for the
English
your digital components according to the LFE channel (LFE Attenuator Setup below).
defaults above. This tells the receiver what
3 Use / to make the adjustments
component is connected to which terminal so
necessary for each setting, pressing RETURN
it corresponds to the buttons on the remote.
to confirm after each screen.
1 Select IN ASSIG. from the System Setup
Dynamic Range Control Setup
Deutsch
menu.
2 Use / to select the number of the Default setting: OFF
digital input to which youve connected your Specifies the amount of dynamic range
digital component. adjustment to Dolby Digital or DTS
The numbers correspond with the numbers soundtracks:
Franais
beside the inputs on the back of the receiver. MAX Dynamic range is reduced (loud
3 Select the component that corresponds sounds are reduced in volume while
with the one you connected to that input. quieter sounds are increased).
Use the / buttons and ENTER to select MID Mid setting.
DVD, TV, CD, CDR, DVR or OFF. OFF No dynamic range adjustment (use
Italiano
If you assign a digital input to a certain when listening at higher volume).
function (for example, DVD) then any
digital inputs previously assigned to that Dual Mono Setup
function will automatically be switched off. Default setting: CH1
4 Press RETURN when youre finished. Specifies how dual mono encoded Dolby
Nederlands
Digital soundtracks should be played:1
CH2 Only channel 2 is played
The Other setup menu CH1 CH2 Both channels are played
The Other menu is where you can make through the front speakers
customized settings to reflect how you are
CH1 Only channel 1 is played
using the receiver.
Espaol
37
En
VSX_516.fm 38
Chapter 8:
Using the tuner
Naming station presets
Listening to the radio You can name your station presets for easy
The following steps show you how to tune in to recall.
FM and AM radio broadcasts and memorize 1 Choose the preset you want to name.
the frequency for recall later. See Listening to station presets below.
1 Press AM or FM to select the tuner band. 2 Press (SHIFT +) TUNER EDIT.
2 Tune to a station. A cursor appears at the first character position.
There are three ways to do this: 3 Input the name you want then press ENTER.
Automatic tuning Press and hold Names can be up to four characters long.
TUNING +/ for about a second. Searching Use the MULTI JOG dial (front panel) or the
automatically stops at the next station. STATION +/ buttons (remote) to select
Manual tuning To change the frequency characters, and ENTER to confirm. If no
one step at a time, press TUNING +/. character is input, a space is input.
High speed tuning Press and hold
TUNING +/ continuously. Tip
If the signal is weak, press the MPX button to Once you have named a station preset, you
switch the receiver into mono reception mode. can press DISPLAY when listening to a
station to switch the display between the
name and the frequency.
Saving station presets
This receiver can memorize up to 30 stations, Listening to station presets
stored in three banks of 10 stations each.1 You will need to have some presets stored to do
this. See Saving station presets on page 38 if
1 Tune to a station you want to memorize. you havent done this already.
2 Press (SHIFT +) TUNER EDIT. 1 Press AM or FM to select the tuner.
The display shows ST. MEMORY, then a
blinking memory class. 2 Press CLASS to select the class in which
the station is stored.
3 Press CLASS to select one of the three Press repeatedly to cycle through classes A, B
classes then press STATION (+/) to select the and C.
station preset you want.
Use the MULTI JOG dial after pressing 3 Press STATION (+/) to select the station
STATION (front panel) to select station preset you want.
presets.
4 Press ENTER to store the station.
Note
1 When saving an FM frequency, the MPX setting is also stored.
38
En
VSX_516.fm 39
English
An introduction to RDS Use the DISPLAY button to display the
Radio Data System (RDS) is a system used by different types of RDS information available.2
most FM radio stations to provide listeners with
Press DISPLAY for RDS information.
various kinds of informationthe name of the
Each press changes the display as follows:
station and the kind of show theyre
Radio Text (RT) Messages sent by the
Deutsch
broadcasting, for example.
radio station. For example, a talk radio
One feature of RDS is that you can search by
station may provide a phone number as RT.
type of program. For example, you can search
for a station thats broadcasting a show with Program Service Name (PS) The name of
the program type, Jazz. the radio station.
You can search the following program types:1 Program Type (PTY) This indicates the
Franais
kind of program currently being broadcast.
News News Finance Stock market
Affairs Current Affairs reports, commerce, Current tuner frequency (FREQ)
Info General Information trading, etc.
Sport Sport Children Programs for
Educate Educational children Searching for RDS programs
Italiano
Drama Radio plays, etc. Social Social affairs You can search for a program type listed above.
Culture National or Religion Programs
regional culture, theater, concerning religion 1 Press the FM button to select the FM
etc. Phone In Public
Science Science and expressing their views by
band.3
technology phone 2 Press PTY SEARCH (front panel).
Varied Usually talk- Travel Holiday-type travel
Nederlands
based material, such as rather than traffic
SEARCH shows in the display.
quiz shows or interviews. announcements
3 Use the MULTI JOG dial to select the
Pop M Pop music Leisure Leisure interests
Rock M Rock music and hobbies program type you want to hear.
Easy M Easy listening Jazz Jazz
Light M Light classical Country Country music
4 Press ENTER to search for the program
music Nation M Popular music type. Espaol
Classics Serious in a language other than The system starts searching through the
classical music English station presets for a match. When it finds one,
Other M Music not fitting Oldies Popular music the search stops and the station plays for five
above categories from the 50s and 60s
seconds.
Weather Weather Folk M Folk music
reports Document Documentary
Note
1 In addition, there are three other program types, TEST, Alarm!, and None. Alarm! and TEST are used for emergency an-
nouncements. You cant search for these, but the tuner will switch automatically to this RDS broadcast signal. None appears
when a program type cannot be found.
2 If any noise is picked up while displaying the RT scroll, some characters may be displayed incorrectly.
If you see NO RADIO TEXT DATA in the RT display, it means no RT data is sent from the broadcast station. The display will
automatically switch to the PS data display (if no PS data, the frequency is displayed).
In the PTY display, NO DATA may be shown. In this case, the PS display is shown after a few seconds.
3 RDS is only possible in the FM band.
39
En
VSX_516.fm 40
Using EON
When EON (Enhanced Other Network
information) is turned on, the receiver jumps to
an EON-linked broadcast when it begins, even
if a receiver function other than the tuner is
being used. It cant be used in areas that EON
information isnt transmitted and when FM
broadcast stations dont transmit PTY data.
When the broadcast ends, the tuner returns to
the original frequency or function.
1 Press the FM button to select the FM
band.2
2 Press EON MODE (front panel) to select
one of the possible modes.
Press repeatedly to switch between:
EON TA (Traffic Announcement) Sets the
tuner to pick up traffic information when it
is broadcast.
EON NEWS Sets the tuner to pick up
news when it is broadcast.
OFF Switches off the EON feature.
When set to TA or NEWS, the EON indicator in
the display lights (it flashes when receiving an
EON broadcast).3 The indicator in the
display lights when the current station carries
the EON service.4
Note
1 RDS searches station presets only. If no stations have been preset, or if the program type could not be found among the station
presets NO PTY is displayed. FINISH means the search is complete.
2 EON is only possible in the FM band.
3 You cant search for traffic announcements and news at the same time.
4 You cannot operate the TUNER EDIT and PTY SEARCH buttons while the EON indicator in the display is lit.
If you want to change to a function other than the tuner when the EON indicator is flashing, press EON MODE to turn EON
off.
40
En
VSX_516.fm 41
Making recordings 09
Chapter 9:
English
Making recordings
Refer to the instructions that came with the
Making an audio or a video recorder if you are unsure how to do this. Most
Deutsch
video recorders set the audio recording level
recording automaticallycheck the components
You can make an audio or a video recording instruction manual if youre unsure.
from the built-in tuner, or from an audio or
video source connected to the receiver (such 5 Start recording, then start playback of the
source component.
Franais
as a CD player or TV).
Keep in mind you cant make a digital
recording from an analog source or vice-versa,
so make sure the components you are
recording to/from are hooked up in the same
way (see Connecting up on page 10 for more on
Italiano
connections).
Nederlands
INPUT SELECTOR
DVD 5.1
USB
CD CD-R FM AM
MIDNIGHT/
STANDARD ADV.SURR STEREO LOUDNESS
Note
1 The receiver's volume, balance, tone (bass, treble, loudness), and surround effects have no effect on the recorded signal.
41
En
VSX_516.fm 42
10 USB playback
Chapter 10:
USB playback
Using the USB interface Basic playback controls
VSX-516 model only The following table shows the basic controls on
the remote for USB playback.
It is possible to listen to two-channel audio1
using the USB interface on the front of this Button What it does
receiver. Connect a USB mass storage device2 Starts normal playback.
as shown below.
Pauses/unpauses playback.
1 Press USB (SHIFT+CD).
Press to start fast reverse scanning
2 Connect your USB device. (press twice for high-speed scanning).
The USB terminal is located on the front panel.
Press to start fast forward scanning.
3 Press (play) to start playback. (press twice for high-speed scanning).
Files/folders play in sequential order based on
Skips to the start of the current track,
the filename (according to the Unicode
then previous tracks.
standard). Within a given directory, all files are
played before continuing to folders/subfolders. Skips to the next track.
In the diagram below, playback proceeds from
folder 0 to folder 5, playing files 1 to 8 in order.
Important
If a USB ERR message lights in the display, try
following the points below:
Folder 0 Folder 1 Folder 2 Folder 3
(Root) (Artisit) (Album) USB ERR What it means
file 1 file 4 file 5 The power requirements of the USB
USB ERR1
device are too high for this receiver.
file 2 file 6
USB ERR2 The USB device is incompatible
file 3 Folder 5 Folder 4
(Artisit) (Album) See Troubleshooting on page 44 for
USB ERR3
more on this error message.
file 8 file 7
Switch the receiver off, then on again.
Make sure the receiver is in standby when
disconnecting the USB device. Reconnect the USB device with the
receiver switched off.
Note
1 This includes playback of WMA/MP3/MPEG-4 AAC files (except files with copy-protection or restricted playback).
2 Compatible USB devices include external magnetic hard drives, portable flash memory (particularly keydrives) and digital
audio players (MP3 players) of format FAT16/32. It is not possible to connect this unit to a personal computer for USB playback.
Pioneer cannot guarantee compatibility (operation and/or bus power) with all USB mass storage devices and assumes no
responsibility for any loss of data that may occur when connected to this receiver.
With large amounts of data, it may take longer for the receiver to read the contents of a USB device.
42
En
VSX_516.fm 43
USB playback 10
English
then switch back to USB. Advanced Audio Coding (AAC) is at the core of
Use a dedicated AC adapter (supplied with the MPEG-4 AAC standard, which incorporates
the device) for USB power. MPEG-2 AAC, forming the basis of the MPEG-4
audio compression technology. The file format
If this doesnt remedy the problem, it is likely
and extension used depend on the application
your USB device is incompatible.
used to encode the AAC file. This unit plays
Deutsch
Compressed audio compatibility back AAC files encoded by iTunes bearing the
extension '.m4a'. DRM-protected files will not
Note that although most standard bit/
play, and files encoded with some versions of
sampling rate combinations for compressed
audio are compatible, some irregularly iTunes may not play.
encoded files may not play back. The list below Apple and iTunes are trademarks of Apple Computer,
Franais
shows compatible formats for compressed Inc., registered in the U.S. and other countries.
audio files: About WMA
MP3 (MPEG-1/2/2.5 Audio Layer 3)
Sampling rates: 8 kHz to 48 kHz; Bit rates:
8 kbps to 320 kbps (128 Kbps or higher
Italiano
recommended); File extension: .mp3
WMA (Windows Media Audio) Sampling
rates: 32 kHz / 44.1 kHz; Bit rates: 32 kbps
to 192 kbps (128 Kbps or higher The Windows Media logo printed on the box
recommended); File extension: .wma; indicates that this receiver can playback
Nederlands
WM9 Pro and WMA lossless encoding: No Windows Media Audio content.
AAC (MPEG-4 Advanced Audio Coding) WMA is an acronym for Windows Media Audio
Sampling rates: 11.025 kHz to 48 kHz; Bit and refers to an audio compression technology
rates: 16 kbps to 320 kbps (128 Kbps or developed by Microsoft Corporation. This unit
higher recommended); File extension: plays back WMA files encoded using Windows
.m4a; Apple lossless encoding: No Media Player bearing the extension '.wma'.
Espaol
Other compatibility information Note that DRM-protected files will not play, and
files encoded with some versions of Windows
VBR (variable bit rate) MP3/WMA/MPEG-4
Media Player may not play.
AAC playback: Yes1
Microsoft, Windows Media, and the Windows logo are
DRM (Digital Rights Management) trademarks, or registered trademarks of Microsoft
protection compatible: Yes (DRM- Corporation in the United States and/or other countries.
protected audio files will not play in this
receiver).
Note
1 Note that in some cases playback time will not be displayed correctly.
43
En
VSX_516.fm 44
11 Additional information
Chapter 11:
Additional information
Troubleshooting
Incorrect operations are often mistaken for trouble and malfunctions. If you think that there is
something wrong with this component, check the points below. Sometimes the trouble may lie in
another component. Investigate the other components and electrical appliances being used. If the
trouble cannot be rectified even after exercising the checks listed below, ask your nearest Pioneer
authorized service center or your dealer to carry out repair work.
If the unit does not operate normally due to external effects such as static electricity
disconnect the power plug from the outlet and insert again to return to normal operating
conditions.
Problem Remedy
The power does not turn on. Disconnect the power plug from the outlet, and insert again.
Make sure there are no loose strands of speaker wire touching the
rear panel. This could cause the receiver to shut off automatically.
If the power shuts off automatically, take the unit to your nearest
Pioneer authorized service center or your dealer for servicing.
No sound is output when a Make sure the component is connected correctly (refer to
function is selected. Connecting up on page 10).
Press MUTE on the remote control to turn muting off.
No image is output when a Make sure the component is connected correctly (refer to
function is selected. Connecting up on page 10).
Select the correct component (use the input select buttons).
Considerable noise in radio Connect the antenna (page 15) and adjust the position for best
broadcasts. reception.
Route any loose cables away from the antenna terminals and wires.
Fully extend the FM wire antenna, position for best reception, and
secure to a wall (or connect an outdoor FM antenna).
Connect an additional internal or external AM antenna (page 15).
Turn off equipment causing interference or move it away from the
receiver (or move antennas farther away from equipment causing
noise).
No sound from surround or Connect the speakers properly (refer to page 16).
center speakers. Refer to Speaker setting on page 35 to check the speaker settings.
Refer to Channel level on page 36 to check the speaker levels.
44
En
VSX_516.fm 45
Additional information 11
Problem Remedy
English
No sound from surround back Refer to Speaker setting on page 35 to check the surround back
speaker. speaker settings.
Refer to Channel level on page 36 to check the speaker levels.
Refer to Using surround back channel processing on page 28 to
make sure surround back channel processing and the sound mode
Deutsch
are set for surround back sound.
Franais
Switch the subwoofer setting in Speaker setting on page 35 to YES
or PLUS.
Switch the LFE Attenuator Setup on page 37 to LFEATT 0 or LFEATT
10.
Noise during playback of a Move the cassette deck further from your receiver, until the noise
Italiano
cassette deck. disappears.
No sound is output or a noise Set the digital volume level of the player to full, or to the neutral
is output when software with position.
DTS is played back.
Nederlands
During a playback search, This is not a malfunction, but be sure to turn the volume down to
noise is output from a DTS prevent the output of loud noise from your speakers.
compatible CD player.
Cant operate the remote Replace the batteries (refer to page 5).
control. Operate within 7 m, 30 of the remote sensor on the front panel
(refer to page 5).
Espaol
Remove the obstacle or operate from another position.
Avoid exposing the remote sensor on the front panel to direct light.
The display is dark or off. Press DIMMER on the remote repeatedly to return to the default.
USB mass storage device is not Try switching the receiver off, then on again.
recognized by the receiver. Make sure you have completely inserted the USB connector to this receiver.
Check that the memory format is FAT16 or FAT32 (FAT12, NTFS and HFS are
not supported).
USB devices with an internal USB hub are not supported.
USB ERR3 shows in the display If this message continues to appear after going through all the checks in
when connecting a USB device. Important on page 42 of USB playback, take the unit to your nearest Pioneer
authorized service center or your dealer for servicing.
Cant play audio files. The WMA or MPEG-4 AAC files were recorded using DRM (digital rights
management), or the bit rate/sampling rate is not compatible (see Compressed
audio compatibility on page 43). This is not a malfunction.
45
En
11_additional_info.fm 46
11 Additional information
46
En
11_additional_info.fm 47
Additional information 11
English
AM loop antenna . . . . . . . . . . . . . . . . . . . . . . . . . 1
Input (Sensitivity/Impedance) FM wire antenna. . . . . . . . . . . . . . . . . . . . . . . . . . 1
DVR/VCR, DVD/LD, TV/SAT . . . . . . . .1 Vp-p/75 Dry cell batteries (AA size IEC R6) . . . . . . . . . . 2
Output (Level/Impedance) Remote control . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
DVR/VCR, MONITOR OUT . . . . . . . . .1 Vp-p/75 Setup microphone (VSX-516 model only) . . . . . . 1
Warranty card . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Deutsch
Frequency response These operating instructions
DVR/VCR, DVD/LD,
TV/SAT MONITOR . . . . . .5 Hz to 7 MHz dB Note
Signal-to-Noise Ratio. . . . . . . . . . . . . . . . . . . 55 dB Specifications and the design are subject
Crosstalk. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 dB to possible modifications without notice,
Franais
FM Tuner Section due to improvements.
Frequency Range. . . . . . . . .87.5 MHz to 108 MHz
Usable Sensitivity . . . . . . . . . Mono:13.2 dBf, IHF Cleaning the unit
(1.3 V/ 75 ) Use a polishing cloth or dry cloth to wipe
50 dB Quieting Sensitivity. . . . . . . Mono: 20.2 dB off dust and dirt.
Stereo: 38.6 dBf
Italiano
When the surface is dirty, wipe with a soft
Signal-to-Noise Ratio. . . Mono: 73 dB (at 85 dBf)
cloth dipped in some neutral cleanser
Stereo: 70 dB (at 85 dBf)
diluted five or six times with water, and
Distortion . . . . . . . . . . . . . . . Stereo: 0.5 % (1 kHz)
wrung out well, and then wipe again with a
Alternate Channel Selectivity . . . 60 dB (400 kHz)
dry cloth. Do not use furniture wax or
Stereo Separation . . . . . . . . . . . . . . 40 dB (1 kHz)
cleansers.
Nederlands
Frequency Response. . . . . . . . . . .30 Hz to 15 kHz
(1 dB) Never use thinners, benzine, insecticide
Antenna Input (DIN) . . . . . . . . . 75 unbalanced sprays or other chemicals on or near this
unit, since these will corrode the surface.
AM Tuner Section
Frequency Range. . . . . . . . . 531 kHz to 1 602 kHz
Sensitivity (IHF, Loop antenna). . . . . . . .350 V/m
Espaol
Signal-to-Noise Ratio. . . . . . . . . . . . . . . . . . . 50 dB
Antenna . . . . . . . . . . . . . . . . . . . . . . Loop antenna
Miscellaneous
Power requirements
. . . . . . . . . . . . . . . .AC 220 V to 230 V, 50 Hz/60 Hz
Power consumption
VSX-416. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 280 W
VSX-516. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 320 W
In standby. . . . . . . . . . . . . . . . . . . . . . . . . . 0.5 W
Dimensions
VSX-416
. . . . . . . 420 (W) mm x 158 (H) mm x 348 (D) mm
VSX-516
. . . . . . 420 (W) mm x 158 (H) mm x 352.5 (D) mm
Weight (without package)
VSX-416. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8.5 kg
VSX-516. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8.9 kg
47
En
VSX_516_Italian.fm Page 2 Friday, January 6, 2006 2:46 PM
IMPORTANTE
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
Il simbolo del lampo con terminale a forma ATTENZIONE: Il punto esclamativo in un triangolo
di freccia situato allinterno di un triangolo PER EVITARE IL RISCHIO DI SCOSSE equilatero serve ad avvisare lutilizzatore
equilatero serve ad avvisare lutilizzatore ELETTRICHE, NON RIMUOVERE IL della presenza di importanti istruzioni di
della presenza di una tensione pericolosa COPERCHIO (O IL RETRO). NON CI SONO funzionamento e manutenzione riportate nel
non isolata nella struttura del prodotto che PARTI INTERNE LA CUI MANUTENZIONE libretto allegato al prodotto.
potrebbe essere di unintensit tale da POSSA ESSERE EFFETTUATA
provocare scosse elettriche allutilizzatore. DALLUTENTE. IN CASO DI NECESSIT,
RIVOLGERSI ESCLUSIVAMENTE A
PERSONALE DI SERVIZIO QUALIFICATO. D3-4-2-1-1_It
ATTENZIONE
Per evitare il pericolo di incendi, non posizionare
sullapparecchio dispositivi con fiamme vive (ad
esempio una candela accesa, o simili). D3-4-2-1-7a_A_It
DOWN
DOWN
VSX_516_Italian.fm Page 3 Friday, January 6, 2006 2:46 PM
Se si vuole eliminare questo prodotto, non gettarlo insieme ai rifiuti domestici. Esiste un sistema di raccolta differenziata in conformit
alle leggi che richiedono appositi trattamenti, recupero e riciclo.
I privati cittadini dei venticinque paesi membri dellUE, di Svizzera e Norvegia, possono restituire senza alcun costo i loro prodotti elettronici usati
ad appositi servizi di raccolta o a un rivenditore (se si desidera acquistarne uno simile).
Per i paesi non citati qui sopra, si prega di prendere contatto con le autorit locali per il corretto metodo di smaltimento.
In questo modo, si sicuri che il proprio prodotto eliminato subir il trattamento, il recupero e il riciclo necessari per prevenire gli effetti
K058_It
potenzialmente negativi sullambiente e sulla vita delluomo.
Se la spina del cavo di alimentazione di questo Questo prodotto conforme alla direttiva sul basso
apparecchio non si adatta alla presa di corrente voltaggio (73/23/CEE emendata 93/68/CEE), direttive
alternata di rete nella quale si intende inserire la EMC 89/338/CEE, emendata 92/31/CEE e 93/68/CEE.
spina stessa, questa deve essere sostituita con una D3-4-2-1-9a_It
adatta allo scopo. La sostituzione della spina del
cavo di alimentazione deve essere effettuata
solamente da personale di servizio qualificato. Dopo
Questo prodotto destinato esclusivamente all'uso
la sostituzione, la vecchia spina, tagliata dal cavo di
domestico. Eventuali disfunzioni dovute ad usi
alimentazione, deve essere adeguatamente
diversi (quali uso prolungato a scopi commerciali, in
eliminata per evitare possibili scosse o folgorazioni
ristoranti, o uso in auto o su navi) e che richiedano
dovute allaccidentale inserimento della spina stessa
particolari riparazioni, saranno a carico dell'utente,
in una presa di corrente sotto tensione.
anche se nel corso del periodo di garanzia. K041_It
Se si pensa di non utilizzare lapparecchio per un
relativamente lungo periodo di tempo (ad esempio,
durante una vacanza), staccare la spina del cavo di
alimentazione dalla presa di corrente alternata di Questo prodotti, VSX-416 e VSX-516 sono conformi al
rete. D3-4-2-2-1a_A_It
DM 28/8/1995, N548, ottemperando alle prescrizioni
di cui al DM 25/6/1985 (par. 3, all. A) e DM 27/8/1987
(All. I). D44-8-4b_It
AVVERTENZA
Linterruttore principale (STANDBY/ON)
dellapparecchio non stacca completamente il flusso
di corrente elettrica dalla presa di corrente alternata
di rete. Dal momento che il cavo di alimentazione Prodotto sotto licenza Dolby Laboratories.
costituisce lunico dispositivo di distacco "Dolby", "Pro Logic", "Surround EX", ed il
dellapparecchio dalla sorgente di alimentazione, il
simbolo doppia D sono marchi registrati
cavo stesso deve essere staccato dalla presa di
corrente alternata di rete per sospendere
della Dolby Laboratories.
completamente qualsiasi flusso di corrente. Verificare
quindi che lapparecchio sia stato installato in modo
da poter procedere con facilit al distacco del cavo di
alimentazione dalla presa di corrente, in caso di "DTS" ,"DTS-ES" ,"DTS 96/24" e
necessit. Per prevenire pericoli di incendi, inoltre, il "Neo:6" sono marchi di fabrica Digital
cavo di alimentazione deve essere staccato dalla Theater Systems, Inc.
presa di corrente alternata di rete se si pensa di non
utilizzare lapparecchio per periodi di tempo
relativamente lunghi (ad esempio, durante una
vacanza). D3-4-2-2-2a_A_It
VSX_516_Italian.fm Page 4 Friday, January 6, 2006 2:46 PM
Capitolo 1:
Prima di cominciare
Attenzione
Controllo dei contenuti della
English
Non usare n conservare le batterie alla luce
scatola diretta del sole o in luoghi eccessivamente
Controllare che siano stati inclusi i seguenti caldi, come allinterno di unautomobile o in
accessori in dotazione: prossimit di un calorifero. Le batterie
potrebbero perdere liquido, surriscaldarsi,
Antenna AM a telaio esplodere o prendere fuoco. In tali
Deutsch
Antenna FM a filo condizioni, anche la durata e le prestazioni
delle batterie potrebbero risultare ridotte.
Pile a secco AA IEC R6 (per verificare il
funzionamento del sistema) x2
Telecomando Gamma operativa del
Impostazione microfono (Solo per il telecomando
Franais
modello VSX-516) Il telecomando ha un raggio dazione di circa 7
Documento di garanzia metri. Potrebbe non funzionare correttamente
Queste istruzioni per luso nei seguenti casi:
Ci sono degli ostacoli tra il telecomando e
il sensore remoto del ricevitore.
Italiano
La luce diretta del sole o una luce
Installazione delle batterie fluorescente arriva direttamente sul
sensore remoto.
Il ricevitore si trova vicino ad un dispositivo
che emette raggi infrarossi.
Nederlands
Il ricevitore usato contemporaneamente
con un altro telecomando a raggi
infrarossi.
5
It
VSX_516_Italian.fm Page 6 Friday, January 6, 2006 2:46 PM
Capitolo 2:
Guida di 5 minuti
La collocazione degli altoparlanti influenza
Presentazione del sistema home notevolmente il suono. Per ottenere un effetto
sonoro ottimale, posizionare gli altoparlanti
theater come indicato di seguito. Per maggiori
Home theater riguarda luso di piste audio dettagli, consultare inoltre Suggerimenti per
multiple per creare un effetto sonoro surround, lubicazione degli altoparlanti a pagina 17.
per farvi sentire al centro dellazione o di un
concerto. Il suono surround che si ottiene da
un sistema home theater non dipende solo
dalla configurazione degli altoparlanti in uso,
ma anche dalla sorgente utilizzata e dalle
impostazioni del ricevitore.
Questo ricevitore decodifica automaticamente
sorgenti multicanale Dolby Digital, DTS o
Dolby Surround a seconda dellimpostazione
degli altoparlanti. Nella maggior parte dei casi,
non sar necessario fare modifiche per
ottenere un suono surround realistico, ma altre * Solo per il modello VSX-516
possibilit (ad esempio lascolto di un CD con
il suono surround multicanale) sono spiegati in 3 Collegare e accendere il ricevitore;
Ascolto del sistema a pagina 25. accendere poi - nellordine - lettore DVD,
subwoofer e televisore.
Assicurarsi di aver impostato lingresso video
Ascolto del suono surround su televisore in questo ricevitore. Controllare il
Questo ricevitore stato disegnato con manuale in dotazione con il televisore per
limpostazione pi facile in mente, quindi con ulteriori istruzioni su come procedere.
questa guida rapida allimpostazione, il 4 Premere QUICK SETUP sul pannello
sistema sar attivato per il suono surround anteriore per specificare la configurazione
praticamente subito. In molti casi, si pu degli altoparlanti, la dimensione della stanza
semplicemente lasciare inalterate le e la posizione di ascolto.
impostazioni standard del ricevitore. Usare il controllo MULTI JOG per la selezione e
Accertarsi di aver effettuato tutte le ENTER per confermare la selezione. Vedi a Uso
connessioni prima di collegare lunit alla della Configurazione rapida sotto per ulteriori
sorgente di alimentazione CA. informazioni al riguardo.
1 Collegare il televisore e il lettore DVD. 5 Riprodurre un DVD e regolare il volume.
Consultare Collegamento di un lettore DVD e di Accertarsi che il display del ricevitore riporti
un televisore a pagina 11. Per un suono lindicazione DVD, che segnala la selezione
surround, utile effettuare linstallazione dellingresso DVD. Altrimenti, premere DVD
usando un collegamento digitale dal lettore sul telecomando per impostare lingresso DVD
DVD al ricevitore. sul ricevitore.
2 Collegare gli altoparlanti e collocarli in Vi sono diverse altre opzioni audio che si
una posizione che consenta di ottenere un possono selezionare. Vedere Ascolto del
suono surround ottimale. sistema a pagina 25 per ulteriori informazioni.1
Vedi a Collegamento degli altoparlanti a Vedere Men System Setup a pagina 31 per
pagina 16. altre opzioni di configurazione.
Nota
1 A volte, secondo il lettore DVD o i dischi stessi, si ottiene solo il suono stereo digitale a 2 canali o il suono analogico. In questo
caso, la modalit di ascolto va impostata su STANDARD (dovrebbe essere gi impostata: alloccorrenza, consultare Ascolto con
il suono surround a pagina 25) se si vuole un suono surround multicanale.
6
It
VSX_516_Italian.fm Page 7 Friday, January 6, 2006 2:46 PM
English
la configurazione degli altoparlanti che
altoparlanti, la dimensione della stanza e la
posizione di ascolto. corrisponde al sistema.
Solo per il modello VSX-516 Per una
configurazione pi dettagliata del
surround, consultare Impostazione
automatica del suono surround (MCACC) a
Deutsch
pagina 8.
Per impostare la configurazione in modo pi
dettagliato, consultare Men System Setup a
pagina 31.
Usare i comandi del pannello anteriore per le
fasi successive.
Franais
Italiano
* Solo per il modello VSX-516
Nederlands
STANDBY/ON per accenderlo. la dimensione della stanza.
A seconda della distanza degli altoparlanti
2 Premere QUICK SETUP.
dalla posizione di ascolto, scegliere tra piccola
3 Verificare le impostazioni del subwoofer. (S), media (M) o grande (L), M una stanza di
Modello VSX-416 Usare il comando MULTI dimensioni medie.
JOG per selezionare YES o NO, a seconda
7 Premere ENTER.
Espaol
che lunit sia collegata o meno a un
subwoofer, quindi premere ENTER.
8 Usare il comando MULTI JOG per scegliere
Modello VSX-516 SW DET lampeggia sul la posizione di ascolto.
display mentre il ricevitore controlla possibile scorrere le seguenti scelte:
limpostazione di un subwoofer. SW YES o
SW NO conferma il controllo del FWD Se si pi vicini agli altoparlanti
subwoofer, quindi il display chiede di centrali che non agli altoparlanti surround
selezionare la configurazione degli MID Se si a distanza uguale dagli
altoparlanti. altoparlanti frontali e da quelli surround
4 Usare il comando MULTI JOG per scegliere BACK Se si pi vicini agli altoparlanti
la configurazione degli altoparlanti. surround rispetto agli altoparlanti frontali
Se si selezionato YES (modello VSX-416) o se
stato rilevato un subwoofer (modello VSX-516) 9 Premere ENTER per confermare la
per limpostazione del subwoofer al punto 3, configurazione.
sono disponibili le seguenti opzioni: Il display mostra la configurazione degli
altoparlanti, la dimensione della stanza e la
2.1ch 3.1ch 4.1ch 5.1ch 6.1ch* posizione di ascolto scelte.
7
It
VSX_516_Italian.fm Page 8 Friday, January 6, 2006 2:46 PM
Capitolo 3:
Impostazione rapida suono
surround
Solo per il modello VSX-516
Nota
1 Il ricevitore esce automaticamente dallo schermo corrente dopo tre minuti dinattivit. Se si cancella la funzione Auto MCACC
Setup in qualsiasi momento, il ricevitore esce automaticamente e non sar effettuata alcuna impostazione.
8
It
VSX_516_Italian.fm Page 9 Friday, January 6, 2006 2:46 PM
English
microfono.
gi) per selezionare una delle seguenti opzioni
ERR Fch Controllare i collegamenti degli
altoparlanti frontali. e premere ENTER, quindi usare / (cursore
s/gi) per controllare le impostazioni:
ERR Sch Controllare i collegamenti degli
altoparlanti surround. CHK SP Controllare dimensione e
ERR SBch Verificare il collegamento del numero degli altoparlanti collegati (vedere
Deutsch
diffusore surround posteriore. a pagina 35 per altri dettagli)
ERR SW Assicurarsi che il subwoofer sia CHK DIST. Controllare la distanza degli
stato acceso e che il volume sul subwoofer altoparlanti dalla posizione di ascolto
sia sufficientemente alto. (vedere a pagina 36 per altri dettagli)
6 Quando si vede CHECK OK sul display, CHK LEVEL Controllare il bilanciamento
confermare la configurazione degli complessivo del sistema degli altoparlanti
Franais
altoparlanti. (vedere a pagina 36 per altri dettagli)
Usare / (cursore s/gi) per controllare a CHK EQ Selezionare ALL CH o F ALIGN
turno ogni altoparlante. YES o NO dovrebbero per controllare le regolazioni al
riflettere gli altoparlanti effettivamente collegati. bilanciamento della frequenza del sistema
Se la configurazione degli altoparlanti degli altoparlanti basato sulle
visualizzata non corretta, usare / (cursore caratteristiche acustiche della stanza
Italiano
sinistra/destra) per cambiare la configurazione. (vedere a pagina 33 per altri dettagli)
Al termine, procedere al punto successivo.
9 Alla fine, selezionare SKIP? per tornare
7 Selezionare CHECK OK sul display e
al menu System Setup.
quindi premere ENTER.
Ricordarsi di scollegare il microfono dopo aver
La funzione Auto MCACC finisce controllando
Nederlands
completato la funzione Auto MCACC Setup.
il livello del subwoofer.
Se il livello di uscita del subwoofer troppo
alto/basso, SW.VOL.DWN/SW.VOL.UP
Altri problemi che possono sorgere
lampeggia sul display per cinque secondi. durante luso della funzione Auto
Per uscire e controllare il livello di uscita MCACC
del subwoofer, premere SETUP o premere Se lambiente della stanza non ottimale per la
semplicemente ENTER quando viene
Espaol
funzione Auto MCACC Setup (troppo rumore di
chiesto RETRY?
fondo, eco contro le pareti, ostacoli che isolano
Il ricevitore emette pi tonalit di prova per la gli altoparlanti dal microfono), le impostazioni
determinazione delle impostazioni ottimali del finali possono risultare errate. Controllare gli
ricevitore relativamente allimpostazione dei
elettrodomestici (condizionatori daria,
diffusori, al livello canale, alla distanza dei
diffusori e alla Calibrazione acustica EQ. frigorifero, ventilatore, ecc.) che possono
influire nellambiente e spegnere gli stessi se
8 E terminata la funzione Auto MCACC Setup! necessario.2 Se ci fossero delle istruzioni sul
La spia MCACC del pannello anteriore pannello anteriore, seguire queste.
sillumina a indicare che le impostazioni
surround sono complete.
Nota
1 Secondo le caratteristiche della stanza, pu capitare che altoparlanti identici con un formato cono intorno a 12cm abbiano
unimpostazione diversa del formato. Si pu correggere manualmente limpostazione usando Impostazione degli altoparlanti a
pagina 35.
Il valore dellimpostazione della distanza del subwoofer pu essere pi distante rispetto alla distanza effettiva dalla posizione
dascolto. Questimpostazione deve essere esatta (prendendo in considerazione il ritardo e le caratteristiche della stanza) e
generalmente non va cambiata.
2 Alcuni televisori di vecchia data possono interferire con il funzionamento del microfono. Potrebbe essere necessario spegnere
il televisore durante luso della funzione Auto MCACC Setup.
9
It
VSX_516_Italian.fm Page 10 Friday, January 6, 2006 2:46 PM
Capitolo 4:
Collegamento
Cavi audio analogici
Come collegare i cavi Usare dei cavi fono RCA stereo per effettuare il
Assicurarsi di non piegare i cavi sulla parte collegamento dei componenti audio analogici.
superiore di questa unit (come mostrato Questi cavi sono rossi e bianchi e bisogna
nellillustrazione). Se ci accade, il campo collegare gli spinotti rossi ai terminali di destra
magnetico prodotto dai trasformatori in questa (R) e gli spinotti bianchi ai terminali di sinistra (L).
unit pu provocare un ronzio dagli altoparlanti.
Nota
1 Quando si collegano i cavi ottici, importante fare attenzione durante linserimento dello spinotto per non danneggiare
lotturatore che protegge la presa ottica.
Per mettere via il cavo ottico, avvolgere lo stesso senza stringere. Il cavo si pu danneggiare se piegato con forza.
anche possibile usare un cavo video RCA standard per effettuare i collegamenti digitali coassiali.
10
It
VSX_516_Italian.fm Page 11 Friday, January 6, 2006 2:46 PM
English
coassiale sul lettore DVD allingresso DIGITAL
COAX 1 (DVD/LD) sul ricevitore.
Usare un cavo audio digitale coassiale per il
collegamento.1
Deutsch
2 Collegare luscita video composita e le
uscite audio analogiche stereo presenti2 sul
lettore DVD agli ingressi DVD/LD su questo
ricevitore.
Usare un cavo video RCA standard e un cavo
fono stereo RCA per il collegamento.
Franais
Se il lettore DVD ha uscite analogiche
multicanale, consultare Collegamento delle
uscite analogiche multicanale sotto per
informazioni su come collegarlo.
Italiano
3 Collegare le uscite audio analogiche dal
televisore agli ingressi TV/SAT su questo
ricevitore.
Ci permetter di riprodurre il suono dal
sintonizzatore incorporato nel televisore. Usare
un cavo fono RCA a tale scopo.
Nederlands
Se il televisore ha un decoder digitale
incorporato, possibile anche collegare
unuscita audio digitale ottica dal
televisore allingresso DIGITAL OPT 1 (CD)
al ricevitore. Usare un cavo ottico per il
collegamento.3
Espaol
Nota
1 Se il lettore DVD ha solo unuscita digitale ottica, possibile collegarlo allingresso ottico su questo ricevitore usando un cavo
ottico. Quando si configura il ricevitore, necessario specificare al ricevitore lingresso al quale si collegato il lettore
(consultare Men Input Assign a pagina 36).
2 Questo collegamento permette di effettuare registrazioni analogiche dal lettore DVD.
3 In questo caso, necessario specificare al ricevitore lingresso digitale al quale si collegato il televisore (consultare Men
Input Assign a pagina 36).
11
It
VSX_516_Italian.fm Page 12 Friday, January 6, 2006 2:46 PM
Collegamento di ricevitori
satellitari o di altri set-top
digitali
I ricevitori satellitari e via cavo e i decoder TV
digitali terrestri sono tutti esempi di set-top
box.
Nota
1 Lingresso multicanale pu essere usato solo quando selezionato DVD 5.1 ch (vedere a pagina 30).
2 Se gi stato collegato il televisore agli ingressi TV/SAT, scegliere semplicemente un altro ingresso. necessario tuttavia
ricordare lingresso al quale si collegata la set-top box.
3 In questo caso, sar necessario specificare a quale ingresso digitale stato collegato il set-top box (vedere Men Input Assign
a pagina 36).
12
It
VSX_516_Italian.fm Page 13 Friday, January 6, 2006 2:46 PM
Collegamento di altri
componenti audio
Il numero e il tipo di collegamenti dipende dal
tipo di componente che si sta collegando.1
Seguire le fasi successive per collegare un CD-
English
R, un MD, un DAT, una piastra a cassette o altri
componenti audio.
1 Se il componente dispone di unuscita
digitale, collegarlo a un ingresso digitale del
ricevitore.
Deutsch
Lesempio illustra un collegamento ottico
allingresso DIGITAL OPT 1 (CD).
2 Se necessario, collegare le uscite audio
analogiche del componente ad una serie di
ingressi audio liberi su questo ricevitore.
Occorrer effettuare questo collegamento per i
Franais
componenti privi di uscita digitale o se si vuole
registrare da un componente digitale. Usare
un cavo fono RCA stereo, come da
illustrazione.
3 Se si collega un registratore, collegare le
Italiano
uscite audio analogiche (REC) agli ingressi
audio analogici sul registratore.
Lesempio mostra un collegamento analogico
alla presa di uscita analogica CD-R/TAPE/MD
usando un cavo fono RCA stereo.
Informazioni sul decoder WMA9 Pro
Nederlands
Questunit ha un decoder Windows Media
Audio 9 Professional (WMA9 Pro) incorporato.
quindi possibile riprodurre laudio WMA9
Pro-encoded usando un collegamento digitale
coassiale o ottico quando collegata ad un Espaol
lettore WMA9 Pro-compatibile. Tuttavia, il
lettore DVD, la set-top box, ecc. devono essere
in grado di emettere segnali audio di formato
WMA9 Pro attraverso unuscita digitale
coassiale o ottica.
Nota
1 Notare che occorre collegare componenti digitali a prese audio analogiche se si vogliono registrare su/da componenti digitali
(quale un MD) su/da componenti analogici.
13
It
VSX_516_Italian.fm Page 14 Friday, January 6, 2006 2:46 PM
Collegamento di altri
componenti video
Questo ricevitore ha ingressi e uscite audio/
video adatti alla connessione di apparecchi di
registrazione video analogici o digitali, inclusi
videoregistratori, registratori DVD e registratori
HDD.
1 Collegare un set di uscite audio/video sul
registratore agli ingressi DVR/VCR AUDIO e
VIDEO del ricevitore.
Usare un cavo fono RCA stereo per il
collegamento audio e un cavo video RCA
standard per il collegamento video.
2 Collegare una serie di ingressi audio/
video sul registratore alle uscite DVR/VCR
AUDIO e VIDEO su questo ricevitore.
Usare un cavo fono RCA stereo per il
collegamento audio e un cavo video RCA
standard per il collegamento video.
3 Se il video componente ha unuscita audio
digitale, collegarlo ad un ingresso digitale su
questo ricevitore.
Lesempio mostra un registratore collegato
allingresso DIGITAL COAX 2 (DVR/VCR) .1
Nota
1 Se il componente video non ha unuscita audio digitale, omettere questa fase. Se ha solo unuscita digitale ottica, possibile
collegarla allingresso ottico sul ricevitore, usando un cavo ottico. Quando si configura il ricevitore, necessario specificare al
ricevitore lingresso al quale si collegato il componente (consultare Men Input Assign a pagina 36).
14
It
VSX_516_Italian.fm Page 15 Friday, January 6, 2006 2:46 PM
English
fig. a fig. b fig. c
Deutsch
5 Per migliorare la ricezione AM
FM UNBAL
75
AM
LOOP ANTENNA Collegare al terminale dellantenna AM un
4
cavo rivestito in vinile di 5 a 6 metri di
lunghezza, senza scollegare lantenna a telaio
Franais
1 2
AM in dotazione.
Italiano
2 Premere le linguette dei connettori per
aprirli, quindi inserire completamente un filo
in ciascun terminale, quindi rilasciare le
linguette per fissare i fili dellantenna AM.
Nederlands
3 Fissare lantenna AM a telaio al supporto. Per ottenere la migliore ricezione possibile,
sospendere lantenna orizzontalmente allaria
Per fissare il supporto allantenna, piegare
aperta.
nella direzione indicata dalla freccia (fig. a)
quindi agganciare il telaio al supporto (fig. b).
Se si intende fissare lantenna AM su una
parete o altra superficie, fissare il supporto
Espaol
con delle viti (fig. c) prima di agganciare il
telaio al supporto. Assicurarsi che la
ricezione sia chiara.
4 Collocare lantenna AM su una superficie
piana e in una direzione che consenta di
ottenere la ricezione migliore.
5 Collegare lantenna FM a filo nello stesso
modo dellantenna AM a telaio.
Per i migliori risultati, srotolare
completamente il filo dellantenna FM e
fissarlo a una parete o al telaio di una porta.
Non lasciare il filo allentato n arrotolato.
15
It
VSX_516_Italian.fm Page 16 Friday, January 6, 2006 2:46 PM
Lillustrazione mostra il modello VSX-516, ma i collegamenti per il VSX-416 sono gli stessi.
16
It
VSX_516_Italian.fm Page 17 Friday, January 6, 2006 2:46 PM
English
Modello VSX-516 del televisore. Se gli altoparlanti non sono
dotati della schermatura magnetica e notate
1 Attorcigliare i trefoli esposti. lo scolorimento dellimmagine televisiva,
allontanare ulteriormente gli altoparlanti dal
2 Allentare il terminale e inserire il filo televisore.
esposto.
Posizionare laltoparlante centrale sopra o
Deutsch
3 Serrare il terminale. sotto il televisore affinch il suono del
canale centrale sia localizzato sullo
Terminali degli altoparlanti schermo televisivo.
Assicurarsi che il filo nudo dellaltoparlante sia Se possibile, porre gli altoparlanti surround
attorcigliato ed inserito completamente nel leggermente al di sopra del livello delle
Franais
terminale dellaltoparlante. Se il filo nudo di un orecchie.
altoparlante tocca il pannello posteriore Cercare di non porre gli altoparlanti
quando si accende lunit, lalimentazione surround pi lontano degli altoparlanti
potrebbe spegnersi come misura di frontali e centrali rispetto alla posizione di
protezione. Usare fili per altoparlanti di buona ascolto per non indebolire leffetto
qualit per collegare gli altoparlanti al
surround.
Italiano
ricevitore.
Per ottenere il miglior suono surround
possibile, installare gli altoparlanti come
Attenzione segue. Assicurarsi che tutti gli altoparlanti
I terminali degli altoparlanti sono sotto siano installati in modo sicuro per
prevenire incidenti e migliorare la qualit
Nederlands
tensione, alla stessa PERICOLOSA tensione
della corrente di rete. Per prevenire rischi di sonora.
folgorazioni nel corso delle operazioni di
collegamento o di distacco dei cavi degli
altoparlanti, staccare il cavo di alimentazione Attenzione
principale prima di toccare qualsiasi parte Se scegliete di installare laltoparlante
non isolata. centrale sopra il televisore, assicurarsi di
Espaol
fissarlo con qualche mezzo, per ridurre il
Suggerimenti per lubicazione degli rischio di danni o lesioni dovuti alla caduta
altoparlanti dellaltoparlante dal televisore in caso di
Gli altoparlanti sono normalmente disegnati scosse esterne, quali terremoti.
per una posizione particolare. Alcuni sono Assicurasi che nessun filo scoperto tocchi
disegnati per essere appoggiati per terra, il pannello posteriore. In tal caso, il
mentre altri devono essere installati su ricevitore potrebbe spegnersi
sostegni per rendere il suono massimo. Alcuni automaticamente.
altoparlanti vanno posizionati vicino ad un
muro; altri ancora vanno allontanati dal muro.
Abbiamo fornito alcuni suggerimenti per
ottenere il migliore suono surround dagli
altoparlanti (qui sotto), ma dovete anche
seguire le linee guida sullubicazione fornite
dal fabbricante degli altoparlanti per ottenere il
massimo dei vostri altoparlanti particolari.
17
It
VSX_516_Italian.fm Page 18 Friday, January 6, 2006 2:46 PM
Nota
1 Solo per il modello VSX-416 Attenersi allo schema di posizionamento dei diffusori, tralasciando i diffusori surround posteriori.
18
It
VSX_516_Italian.fm Page 19 Friday, January 6, 2006 2:46 PM
Capitolo 5:
Controlli e display
Pannello anteriore
English
Lillustrazione mostra il modello VSX-516
Deutsch
Franais
Italiano
Nederlands
1 Tasti di selezione dellingresso 4 ENTER
Consente di selezionare una sorgente di
5 Controllo MULTI JOG
ingresso.
Il controllo MULTI JOG svolge diverse funzioni.
Espaol
2 Display dei caratteri Utilizzarlo per selezionare diverse opzioni dopo
Vedi a Display a pagina 21. aver premuto i tasti MULTI JOG designati.
3 Indicatore MCACC (Solo per il modello VSX- 6 SIGNAL SELECT
516) Consente di selezionare un segnale di ingresso
Si illumina quando attiva la funzione (pagina 27).
Acoustic Calibration EQ (pagina 27) (la
funzione Acoustic Calibration EQ impostata 7 SB ch PROCESSING (Solo per il modello
automaticamente su ALL CH ADJUST dopo VSX-516)
aver eseguito la funzione Auto MCACC Setup Consente di selezionare unopzione per il
(pagina 8) o EQ Auto Setup (pagina 33)). canale surround posteriore (pagina 27) oppure
(nel caso in cui non sia disponibile un diffusore
surround posteriore) di attivare la modalit
Virtual Surround Back (VSB) (pagina 28).
19
It
VSX_516_Italian.fm Page 20 Friday, January 6, 2006 2:46 PM
20
It
VSX_516_Italian.fm Page 21 Friday, January 6, 2006 2:46 PM
Display
Lillustrazione mostra il modello VSX-516
1 2 3 4 5 6 7 8 9 10 11 12 13
EON [L] 6
English
RDS [C]
SP A [R]
[Rs ] 0
[SBR]
[SB L ]
[Ls ]
6
Deutsch
14 15 16 17 18 19 20 21 22 23
Franais
un segnale multicanale Dolby Digital.
AUTO
Sillumina quando attiva la selezione di 4 2 PRO LOGIC IIx (modello VSX-516) /
segnale AUTO. 2 PRO LOGIC II x (modello VSX-416)
Quando sul ricevitore attiva la modalit
SB (Solo per il modello VSX-516)
(STANDARD) Pro Logic II, 2 PRO LOGIC
Italiano
A seconda della fonte, sillumina quando
II si illumina per indicare la decodifica Pro
viene rilevato un segnale con una codifica
Logic II. 2 PRO LOGIC IIx si illumina per
di canale posteriore surround.
indicare la decodifica Pro Logic IIx (per
DIGITAL maggiori dettagli, consultare Ascolto con il
Sillumina quando viene rilevato un suono surround a pagina 25).
Nederlands
segnale audio digitale.
5 VIR.SB
DTS Sillumina durante lelaborazione posteriore
Sillum quando viene rilevata una fonte surround virtuale (pagina 28).
con segnali audio con codifica DTS.
6 DIRECT
2 DIGITAL Sillumina quando in uso la riproduzione Espaol
Sillumina quando viene rilevato un diretta da fonte. La riproduzione diretta ignora
segnale di codifica Dolby Digital. i controlli del tono per la riproduzione ottimale
della sorgente.
ANALOG
Sillumina quando viene rivelato un 7 AUTO SURR.
segnale analogico. Sillumina quando attiva la funzione Auto
Surround (vedere Riproduzione automatica a
2 pagina 25).
Quando attiva la modalit STANDARD del
8 ATT
ricevitore, sillumina per indicare la codifica di
Silluminaquando usate ANALOG ATT per
un segnale multicanale DTS.
attenuare (ridurre) il livello del segnale
dingresso analogico.
9 SLEEP
Sillumina quando il ricevitore si trova nella
modalit di riposo.
21
It
VSX_516_Italian.fm Page 22 Friday, January 6, 2006 2:46 PM
22
It
VSX_516_Italian.fm Page 23 Friday, January 6, 2006 2:46 PM
1 RECEIVER LEVEL +/
Commuta il ricevitore tra standby e on. Consente di regolare i livelli di effetti e
2 Tasti Listening mode canali.
English
opzioni 2Pro Logic II e Neo:6 (Solo per il acustica (pagina 27).
modello VSX-516) (pagina 25).
MUTE
ADV.SURR
Silenzia/ripristina laudio.
Consente di alternare le varie modalit
surround (pagina 26). 6 SHIFT
Premere questo tasto per accedere ai comandi
Deutsch
STEREO circondati da un rettangolo (sopra ai tasti) sul
Cambia tra la riproduzione diretta e quella telecomando. Nella presente sezione, questi
stereo (pagina 27). Consente inoltre di tasti sono contrassegnati da un asterisco (*).
selezionare la modalit Auto Surround
(Riproduzione automatica a pagina 25). 7 SLEEP
Consente di modificare l'intervallo di tempo
Franais
MIDNIGHT/LOUDNESS precedente all'attivazione della modalit di
Commuta sulla modalit di ascolto riposo sul ricevitore (90 min 60 min 30
Midnight o Loudness (pagina 29). min Off). E possibile controllare il tempo
3 TOP MENU rimanente dello sleep timer in qualsiasi
Visualizza il men top di un DVD. momento premendo SLEEP una volta.
DIMMER
Italiano
SETUP
Premere per accedere al menu System Rende il display pi tenue o pi luminoso.
Setup (pagina 31). ANALOG ATT
4 TUNER EDIT* Attenua (diminuisce) il livello di un segnale
Consente di memorizzare e assegnare un dingresso analogico per prevenire la
Nederlands
nome alle stazioni, per poterle richiamare distorsione del suono.
in seguito (pagina 38). Funziona anche 8 Tasti INPUT SELECTOR
come il tasto SETUP per le unit DVD/DVR. Premere questo per selezionare una fonte
S. RETRIEVER dingresso.
Premere questo tasto per ripristinare un
DVD/DVR
suono di qualit CD per le sorgenti audio
Premere questo tasto per usare i comandi
Espaol
compresse (pagina 30).
DVD/DVR presenti sul telecomando.
5 Tasti RECEIVER CONTROL
RECEIVER
VOLUME +/ Usare per passare ai comandi del ricevitore
Usato per impostare il volume dascolto. sul telecomando. Si usa per impostare il
EFFECT/CH SEL suono surround per il ricevitore
Premere ripetutamente per selezionare un (pagina 31).
canale, quindi usare LEVEL +/ per 9 MENU
regolare il livello (pagina 36). Consente Visualizza il men del disco dei DVD/
inoltre di regolare il livello degli effetti videodischi.
Advanced Surround, nonch i parametri
Dolby Pro Logic IIx Music e Neo:6 Music DIALOG E
(pagina 26). Si possono quindi utilizzare i Usato per dar rilievo al dialogo mentre
tasti LEVEL +/ per effettuare queste guardate la TV o un film (pagina 29).
regolazioni.
23
It
VSX_516_Italian.fm Page 24 Friday, January 6, 2006 2:46 PM
24
It
VSX_516_Italian.fm Page 25 Friday, January 6, 2006 2:46 PM
Capitolo 6:
Ascolto del sistema
Solo per il modello VSX-516 Se si collegato
Importante un diffusore surround posteriore, si veda
English
Alcune funzioni spiegate in questa sezione anche Uso dellelaborazione del canale
non saranno possibili a seconda della posteriore surround a pagina 28.
fonte (ad esempio, PCM 88,2 kHz / 96 kHz,
DTS 96 kHz (24 bit) o fonti WMA 9 Pro).
Deutsch
Premere STANDARD durante lascolto
Riproduzione automatica della fonte.
Lopzione di ascolto pi semplice e diretta Se la fonte codificata Dolby Digital, DTS o
consiste nelluso della funzione Auto Dolby Surround, il formato di decodificazione
Surround. Con questa funzione, il ricevitore corretto verr selezionato automaticamente e
Franais
rivela automaticamente il tipo di fonte in fase di
visualizzato sul display.2
riproduzione e seleziona la riproduzione
multicanale o stereo.1 Con fonti a due canali, premere STANDARD
ripetutamente per selezionare da3:
2 Pro Logic II MOVIE Suono fino a 5.1
canali, particolarmente adatto per i film
Italiano
2 Pro Logic II MUSIC Suono fino a 5.1
Quando si ascolta una fonte, premere
canali, specialmente adatto per le fonti
STEREO per la riproduzione automatica di
musicali
una fonte.
Premere ripetutamente fino a che AUTOSURR. 2 PRO LOGIC Suono surround a 4.1
Nederlands
non viene mostrato brevemente sul display canali
(indicher quindi il formato di decodifica o di Solo per il modello VSX-516:
riproduzione). Controllare le spie del formato 2 Pro Logic IIx MOVIE Suono fino a 6.1
digitale sul display per vedere lelaborazione canali, particolarmente adatto per i film
della fonte.
2 Pro Logic IIx MUSIC Suono a 6.1
canali, particolarmente adatto per le fonti
Espaol
musicali
Ascolto con il suono surround 2 Pro Logic IIx GAME Suono a 6.1
Usando questo ricevitore, possibile ascoltare canali, particolarmente adatto ai video
una qualsiasi fonte con il suono surround. giochi
Comunque, le opzioni disponibili dipendono
dallimpostazione dellaltoparlante e dal tipo di
fonte in fase di ascolto.
Nota
1 Solo per il modello VSX-516 Los formatos de sonido envolvente estreo (matriz) se descodifican con Neo:6 CINEMA o 2
Pro Logic IIx MOVIE (para ms detalles sobre estos formatos de descodificacin, consulte Ascolto con il suono surround sopra).
La funzione Auto Surround viene cancellata se collegate le cuffie o selezionate gli ingressi analogici multicanale.
2 Solo per il modello VSX-516 Se lelaborazione del canale surround posteriore (pagina 27) impostata su OFF o se il diffusore
surround posteriore impostato su NO (pagina 35), 2 Pro Logic IIx diventa 2 Pro Logic II (suono a 5.1 canali).
3 Durante lascolto alle fonti a 2 canali nella modalit Dolby Pro Logic II(x) Music, ci sono altri tre parametri da regolare: Center
Width, Dimension, e Panorama. Consultare Impostazione delle opzioni relative agli effetti sotto per regolare tali parametri.
25
It
VSX_516_Italian.fm Page 26 Friday, January 6, 2006 2:46 PM
2 PRO LOGIC Suono surround a 4.1 canali 6-STEREO (Solo per il modello VSX-516)
Neo:6 CINEMA Suono a 6.1 canali, Simula un suono multicanale per una
sorgente stereo, usando tutti gli
particolarmente adatto per i film altoparlanti.
Neo:6 MUSIC1 Suono a 6.1 canali, VIR. SURR Crea un effetto surround
particolarmente adatto per le fonti musicali virtuale usando soltanto il subwoofer e gli
altoparlanti frontali.
Solo per il modello VSX-516 Con le fonti
multicanale, se si sono collegati gli altoparlanti EX POWER (Solo per il modello VSX-416)
posteriori surround e se stato selezionato SB Selezionare questa modalit quando si
utilizzano gli altoparlanti surround insieme
ON, possibile selezionare (a seconda del agli altoparlanti frontali (vedere lo schema
formato): di pagina 18 per limpostazione degli
2 Pro Logic IIx MUSIC Vedi sopra altoparlanti in modalit Extra Power).
Dolby Digital EX Crea un suono del PHONESUR. Crea un effetto surround
canale surround posteriore per le fonti a generale attraverso la cuffia.
5.1 canali e fornisce una decodificazione
pura per le fonti a 6.1 canali (come Dolby Impostazione delle opzioni relative
Digital Surround EX) agli effetti
DTS-ES Vi consente di riprodurre fonti a Quando si usano gli effetti surround,
6.1 canali con la codificazione DTS possibile regolare numerosi parametri.
1 Premere ripetutamente EFFECT/CH SEL
Uso degli effetti surround Advanced per selezionare il parametro che si desidera
La funzione Advanced surround crea una vasta regolare.
gamma di effetti surround. Provare le diverse A seconda dello stato o della modalit corrente
modalit con varie colonne sonore per del ricevitore, alcune opzioni potrebbero non
soddisfare le proprie preferenze.2 essere disponibili. Per maggiori informazioni
fare riferimento alla tabella che segue.
Solo per il modello VSX-416 Tra le opzioni
elencate, disponibile solo il parametro
EFFECT.
Premere ADV.SURR ripetutamente per 2 Usare i tasti LEVEL +/ per impostare il
selezionare una modalit dascolto. parametro secondo le proprie esigenze.
ADV. MOVIE Adatta per la visione di film. Per conoscere le opzioni disponibili per
ADV. MUSIC Adatta per le sorgenti ciascun parametro consultare la tabella che
musicali. segue. I valori predefiniti, se non indicati come
TV SURR. Produce un suono surround per tali, sono elencati in grassetto.
le sorgenti televisive sia mono sia stereo.
SPORTS Adatta per i programmi sportivi.
ADV. GAME Adatta per i videogiochi.
EXPANDED Simula un suono
multicanale per le sorgenti a due canali.3
Nota
1 Con sorgenti a 2 canali nella modalit Neo:6 Music, possibile regolare leffetto Center image (consultare Impostazione delle
opzioni relative agli effetti sotto).
2 Premendo ADV.SURR con la cuffia collegata, viene selezionata automaticamente lopzione PHONES SURROUND.
A seconda della sorgente e della modalit audio selezionata, il diffusore posteriore surround presente nella configurazione
potrebbe non emettere audio. Per maggiori dettagli, consultare la sezione Uso dellelaborazione del canale posteriore surround a
pagina 28.
Quando si seleziona una modalht di ascolto Advanced Surround, possibile regolare il livello degli effetti usando il
parametro EFFECT in Impostazione delle opzioni relative agli effetti sotto.
3 Usare con Dolby Pro Logic per un effetto surround stereo (il campo stereo pi ampio rispetto alle modalit Standard con
sorgenti Dolby Digital).
26
It
VSX_516_Italian.fm Page 27 Friday, January 6, 2006 2:46 PM
English
(Valido solo sinistro e destro, ampliando zione
se si utilizza (impostazioni pi alte) o predefi- Durante lascolto di una fonte, premere
un restringendo (impostazioni pi nita: 3
STEREO per la riproduzione stereo.
altoparlante basse) tale canale.
centrale) Premere ripetutamente per commutare tra:
STEREO Laudio viene ascoltato con le
Dimensiona Regola il bilanciamento del 3 a +3
Deutsch
suono surround dalla parte Imposta- impostazioni surround definite dallutente;
anteriore a quella posteriore, zione comunque possibile usare le funzioni
rendendo il suono pi distante predefi- Midnight, Loudness e Tone.
(impostazione negativa) o pi nita: 0
vicino (impostazione positiva).
DIRECT Oltrepassa tutti gli effetti ed
impostazioni surround in modo tale che
Panoramaa Amplia limmagine stereo OFF laudio rimanga il pi vicino possibile al
Franais
frontale fino a comprendere gli
altoparlanti surround per ON segnale audio della fonte.1
ottenere un effetto avvolgente. AUTO SURR. Per maggiori dettagli,
Center Regola limmagine centrale per 0 a 10
consultare Riproduzione automatica a
Imageb creare un effetto stereo pi Imposta- pagina 25.
(Valido solo ampio per le voci. Regolare zione
Italiano
se si utilizza leffetto da 0 (il canale centrale predefi-
un viene trasmesso agli nita: 3
altoparlante altoparlanti anteriori destro e Ascolto con la funzione Acoustic
centrale) sinistro) a 10 (il canale centrale
viene trasmesso solo
Calibration EQ
allaltoparlante centrale). Solo per il modello VSX-516
Nederlands
Effect Imposta il livello degli effetti per 10 a 90
Impostazione standard: OFF / ALL CH
la modalit Advanced Surround (dopo Auto MCACC Setup o EQ Auto
selezionata (ciascuna modalit Setting)
pu essere impostata
E possibile ascoltare le fonti usando la
separatamente).
funzione Acoustic Calibration Equalization
a Disponibile solo con sorgenti a 2 canali in modalit Dolby impostata in Impostazione automatica del
Espaol
Pro Logic IIx Music. suono surround (MCACC) a pagina 8 o
b Disponibile solo con sorgenti a 2 canali in modalit Neo:6
Music.
Calibratura acustica EQ a pagina 33. Vedere a
queste pagine per ulteriori informazioni sulla
funzione Acoustic Calibration Equalization.
Ascolto stereo
Alla selezione STEREO o DIRECT, sentirete la
fonte solo attraverso gli altoparlanti anteriori di
sinistra e destra (e possibilmente anche
attraverso il subwoofer, secondo le Durante lascolto di una fonte, premere
impostazioni dellaltoparlante). (SHIFT +) ACOUSTIC EQ.
Premere ripetutamente per selezionare tra:
ALL CH Nessun peso speciale viene dato
ad un canale particolare.
Nota
1 Se si attiva lascolto in modalit Midnight, Loudness, Dialog Enhancement, la funzione Sound Retriever o i comandi tonalit
quando selezionata la modalit DIRECT, il ricevitore passa automaticamente alla modalit STEREO.
27
It
VSX_516_Italian.fm Page 28 Friday, January 6, 2006 2:46 PM
28
It
VSX_516_Italian.fm Page 29 Friday, January 6, 2006 2:46 PM
posteriore surround oppure - nel caso in cui il VSB ON Virtual Surround Back sempre
suono risulti migliore nel formato di codifica usato (ad esempio per il materiale
originale del materiale (ad esempio 5.1) - codificato 5.1)
possibile specificare al ricevitore che questo
effetto sia applicato solo alle sorgenti con VSB AUTO (Solo per il modello VSX-516) La
codifica 6.1, quali Dolby Digital EX o DTS-ES.1 funzione Virtual Surround Back viene
Solo per il modello VSX-516 Questa tabella applicata automaticamente alle sorgenti
indica quando sentirete il canale surround con codifica 6.1 (ad esempio, Dolby Digital
English
posteriore virtuale (= Il suono viene EX o DTS-ES)
riprodotto attraverso il diffusore surround). VSB OFF La modalit Virtual Surround
Premere SB ch (SB ch PROCESSING)/ VSB Back disattivata
MODE per selezionare unopzione per il
canale posteriore surround virtuale.
Deutsch
Ad ogni pressione, la selezione cambia come segue:
Standard
SBch
Surround
Tipo di fonte Processing / Fonti Fonti stereo
Advanced
Modalit VSB multicanale 2 Pro Logic II x 2 Pro Logic Neo:6
ON
Franais
Fonte Dolby Digital EX/DTS- a
ES/WMA9 Pro multicanale
codificata a 6.1 canali AUTO a
surround
Italiano
Fonte stereo codificata Dolby ON a,b a
Digital/DTS/WMA9 Pro; altra
fonte stereo digitale AUTO c a
Nederlands
a Escluso il formato WMA9 Pro
b Valido solo utilizzando la modalit Virtual Surround Back.
c Non valido quando si utilizza la modalit Virtual Surround Back.
Nota
1 La modalit Virtual Surround Back non pu essere usata con le cuffie, in modalit STEREO / DIRECT, n se il diffusore
surround impostato su NO in Impostazione degli altoparlanti a pagina 35 (solo per il modello VSX-516 il diffusore posteriore
surround deve essere comunque impostato su NO).
29
It
VSX_516_Italian.fm Page 30 Friday, January 6, 2006 2:46 PM
Nota
1 La funzione Sound Retriever valida solo per le sorgenti a 2 canali.
2 Durante la riproduzione da ingressi multicanale, non possibile usare alcuna funzione o modalit audio ed possibile
impostare solo i livelli relativi a volume e canali.
30
It
VSX_516_Italian.fm Page 31 Friday, January 6, 2006 2:46 PM
Capitolo 7:
Men System Setup
Uso del menu System Setup Impostazione manuale dei
English
La sezione che segue spiega come impostare diffusori mediante il menu
in dettaglio i parametri che consentono di
specificare lutilizzo del ricevitore. Viene inoltre Manual MCACC
descritta la regolazione di precisione delle Solo per il modello VSX-516
impostazioni di sistema per i singoli E possibile usare le impostazioni nel men
Deutsch
altoparlanti. dimpostazione manuale MCACC per fare delle
regolazioni dettagliate quando avete
familiarizzato con il sistema. Prima di fare
queste impostazioni, bisogna aver completato
la procedura Impostazione automatica del
suono surround (MCACC) a pagina 8.
Franais
1 Premere RECEIVER sul telecomando, poi Queste impostazioni vanno fatte solo una volta
premere il tasto SETUP. (se non cambiate lubicazione dellattuale
sistema di altoparlanti o aggiungete nuovi
2 Usare / per selezionare altoparlanti).
limpostazione che si desidera regolare e
quindi premere ENTER.
Italiano
A. MCACC (Solo modello VSX-516) Questa Importante
modalit costituisce un modo rapido, Per alcune delle impostazioni qui sotto,
efficiente e automatico per impostare il bisogna collegare il microfono al pannello
suono surround (vedi a Impostazione anteriore e posizionarlo al livello
automatica del suono surround (MCACC) a
Nederlands
dellorecchio nella normale posizione
pagina 8). dascolto. Vedi a Impostazione automatica
M. MCACC (Solo modello VSX-516) Per del suono surround (MCACC) a pagina 8 se
sintonizzare con precisione le impostazioni non siete sicuri come procedere. Vedere
degli altoparlanti e personalizzare leffetto Altri problemi che possono sorgere durante
Acoustic Calibration EQ (vedi a luso della funzione Auto MCACC a
Impostazione manuale dei diffusori pagina 9 per le note sugli alti livelli di
Espaol
mediante il menu Manual MCACC sotto). rumore sullo sfondo e altre possibili
SP SETUP Specificare dimensione, interferenze.
numero, distanza e bilanciamento Se si usa un subwoofer, attivarlo ed alzare
complessivo degli altoparlanti collegati il volume nella posizione centrale.
(vedere Impostazione manuale dei diffusori
mediante il menu Manual MCACC sotto). 1 Selezionare M.MCACC dal men System
Setup.
IN ASSIG. Specificare cosa si collegato Vedi a Uso del menu System Setup sopra se
agli ingressi digitale e dei componenti non gi visualizzato questo schermo.
video (vedere Men Input Assign a
pagina 36). 2 Selezionare limpostazione da regolare.
OTHER Effettuare impostazioni Se queste sono le prime impostazioni, bisogna
personalizzate a seconda di come si sta eseguirle in ordine.
usando il ricevitore (vedere il Menu di CH LEVEL Effettuare regolazioni fini al
impostazione Other a pagina 37). bilanciamento complessivo del sistema di
diffusori (vedere Livello canale ottimo
sotto).
31
It
VSX_516_Italian.fm Page 32 Friday, January 6, 2006 2:46 PM
32
It
VSX_516_Italian.fm Page 33 Friday, January 6, 2006 2:46 PM
Cercare di far suonare i due toni come se 1 Selezionare EQ A. SET dal men
arrivassero contemporaneamente ad una dimpostazione Manuale MCACC.
posizione leggermente davanti a voi tra le Assicurarsi che sia collegato il microfono.
braccia. Se state usando un subwoofer, questo
viene rivelato automaticamente
ogniqualvolta si accende il sistema.
Assicurarsi che sia acceso e che il volume
English
sia nella posizione centrale.
Vedere anche Altri problemi che possono
sorgere durante luso della funzione Auto
Quando sembra che le impostazioni di ritardo MCACC a pagina 9 per le note sugli alti
siano corrispondenti, premere l (cursor gi) livelli di rumore di fondo e altre possibili
per confermare e continuare sul canale interferenze.
Deutsch
successivo.
2 Attendere il termine della funzione EQ
Per consentire un confronto, laltoparlante Auto Setup.
di riferimento cambia secondo Mentre il ricevitore emette i toni di prova, il
laltoparlante selezionato. bilanciamento della frequenza viene regolato
Se si vuole tornare indietro e regolare un automaticamente per le seguenti
Franais
canale, usare semplicemente / per impostazioni:
selezionarlo. A. CH La regolazione All Channel Adjust
(tutti i canali) unimpostazione piatta, in
4 Al termine, premere RETURN. cui tutti gli altoparlanti sono impostati
Lunit ritorner al men dimpostazione individualmente. Quindi, nessun peso
manuale MCACC.
Italiano
speciale viene dato ad un canale
particolare.
Calibratura acustica EQ F.ALG La regolazione Front Align Adjust
La funzione Acoustic Calibration Equalization (Allineamento frontale) bilancia il suono
un tipo dequalizzatore per gli altoparlanti complessivo in modo che tutti gli
(escluso il subwoofer). Funziona misurando le altoparlanti siano impostati secondo le
Nederlands
caratteristiche acustiche della stanza e impostazioni degli altoparlanti frontali
neutralizzando le caratteristiche ambientali (nessuna equalizzazione viene applicata ai
che possono colorare il materiale della fonte canali frontali sinistro e destro).
originale. Questo fornisce unimpostazione Lunit ritorner al men dimpostazione
dequalizzazione piatta. Se non siete Acoustic Cal EQ dopo aver impostato Acoustic
soddisfatti della regolazione automatica, Calibration Equalization.
Espaol
possibile regolare queste impostazioni
manualmente per ottenere un bilanciamento Copiatura delle impostazioni Acoustic
della frequenza adatto al vostro gusto Calibration EQ
personale. Se si vuole regolare manualmente lAcoustic
Calibration EQ (vedere Impostazione manuale
Impostazione automatica della funzione della funzione Acoustic Calibration EQ sotto),
Acoustic Calibration EQ consigliamo di copiare le impostazioni A. CH o
Se si gi completata Impostazione F.ALG dallimpostazione EQ A. SET
automatica del suono surround (MCACC) a precedente (o da Impostazione automatica del
pagina 8, A. CH ADJ e F.ALG ADJ (sotto) suono surround (MCACC) a pagina 8) su una
dovrebbero gi essere impostati. Perci, se si delle impostazioni personalizzate (C1 o C2).
Invece di fornire una curva EQ piatta, fornisce
desidera regolare le impostazioni
un punto di riferimento da cui iniziare.
manualmente, saltare a Impostazione manuale
della funzione Acoustic Calibration EQ sotto. 1 Selezionare EQ COPY dal men
dimpostazione manuale MCACC.
33
It
VSX_516_Italian.fm Page 34 Friday, January 6, 2006 2:46 PM
34
It
VSX_516_Italian.fm Page 35 Friday, January 6, 2006 2:46 PM
English
manuale MCACC. altoparlanti anteriori riproducono le
frequenze dei bassi efficientemente
oppure se non stato collegato un
Configurazione manuale degli subwoofer. Selezionare SMALL per inviare
altoparlanti le basse frequenze al subwoofer.1
Queste impostazioni ottimizzano le prestazioni del
Deutsch
Center (C) Selezionare LARGE se
suono surround (se si ritengono adeguate le
impostazioni eseguite in Uso della Configurazione laltoparlante centrale riproduce le basse
rapida a pagina 7 oppure in Impostazione frequenze efficientemente oppure
automatica del suono surround (MCACC) a selezionare SMALL per inviare le basse
pagina 8 (solo per il modello VSX-516), non frequenze allaltro altoparlante o subwoofer.
necessario effettuare ulteriori regolazioni). Queste Se non stato collegato un altoparlante
Franais
impostazioni vanno fatte solo una volta (se non centrale, scegliere NO (il canale centrale
cambiate lubicazione dellattuale sistema di viene inviato agli altoparlanti anteriori).
altoparlanti o aggiungete nuovi altoparlanti). Surround (S) Selezionare LARGE se gli
1 Selezionare SP SETUP dal men System Setup. altoparlanti surround riproducono in modo
efficace le frequenze basse. Selezionare
2 Usare / per selezionare SMALL per inviare le basse frequenze
Italiano
limpostazione che si desidera regolare e allaltro altoparlante o subwoofer. Se non
quindi premere ENTER. sono stati collegati gli altoparlanti
SP SET Specificare le dimensioni e il numero surround, scegliere NO (il suono dei canali
di altoparlanti che si sono collegati (vedere surround viene inviato agli altoparlanti
Impostazione degli altoparlanti sotto). anteriori o al subwoofer).
Nederlands
X.OVER Specificare quali frequenze Surround Back (SB) Selezionare LARGE
saranno inviate al subwoofer (vedere Rete
Crossover sotto). se gli altoparlanti posteriori surround
riproducono in modo efficace le frequenze
CH LEVEL Regolare il bilanciamento
basse. Selezionare SMALL per inviare le
complessivo del sistema di altoparlanti
(vedere Livello del canale sotto). frequenze basse agli altri diffusori o al
subwoofer. Se non si collegato il diffusore
SP DISTN. Specificare la distanza degli
Espaol
altoparlanti dalla posizione dascolto surround posteriore, selezionare NO.2
(vedere Distanza dell altoparlante sotto). Subwoofer (SW) I segnali LFE e le basse
3 Premere RETURN dopo aver regolato frequenze dei canali impostati su SMALL
ciascun parametro secondo le proprie esigenze. sono emessi dal subwoofer se si seleziona
YES. Scegliere limpostazione PLUS per far
Impostazione degli altoparlanti emettere il suono dei bassi dal subwoofer
continuamente o per dei bassi pi profondi
Usare questimpostazione per specificare la
configurazione degli altoparlanti (formato, (le frequenze basse normalmente riprodotte
numero di altoparlanti).
Nota
1 Se si seleziona SMALL per i diffusori frontali, il subwoofer fisso su YES. Inoltre, non possibile impostare su LARGE i diffusori
centrale, surround e surround posteriore se i diffusori frontali sono impostati su SMALL. In questo caso, tutte le frequenze basse
sono inviate al subwoofer.
2 Se i diffusori surround sono impostati su NO, il diffusore surround posteriore viene impostato automaticamente su NO.
Se si seleziona un solo altoparlante posteriore surround, accertarsi che tale altoparlante sia collegato al terminale surround
posteriore sinistro.
35
It
VSX_516_Italian.fm Page 36 Friday, January 6, 2006 2:46 PM
dagli altoparlanti anteriori e centrale sono 4 Regolare il livello di ciascun canale mediante
inviate al subwoofer)1. Se non si collegato i tasti /.
un subwoofer, selezionare NO (i bassi Se stato selezionato T. TONE M., usare /
vengono emessi dagli altri altoparlanti). per passare da un altoparlante allaltro.
Limpostazione T. TONE A. emette i toni di
Rete Crossover prova nel seguente ordine (a seconda delle
Impostazione standard: 100Hz impostazioni degli altoparlanti):
Questimpostazione decide il taglio tra i suoni L C R RS SB* LS SW
dei bassi riproducendo i toni da tutti gli *Solo per il modello VSX-516
altoparlanti selezionati come LARGE, o il
subwoofer e riproduce i suoni bassi da quelli Regola il livello di ogni altoparlante durante
selezionati come SMALL.2 Inoltre decide dove lemissione del tono di prova.4
tagliare i bassi nel canale LFE.
Distanza dell altoparlante
1 Selezionare X.OVER dal menu SP SETUP. Per una buona profondit sonora ed unottima
2 Usare / per scegliere il punto di separazione dal sistema, bisogna specificare
taglio della frequenza. la distanza degli altoparlanti dalla posizione
Le frequenze sotto il punto di taglio saranno dascolto.5 Il ricevitore sar poi in grado di
trasmesse al subwoofer (o altoparlanti LARGE). aggiungere il ritardo necessario per un suono
surround efficiente.
Livello del canale 1 Selezionare SP DISTN. dal men SP SETUP.
Mediante queste impostazioni possibile
regolare il bilanciamento generale del sistema 2 Usare / per scegliere laltoparlante
di altoparlanti. desiderato, quindi impostare la distanza.
Usare / per regolare la distanza di ogni
1 Selezionare CH LEVEL dal men SP SETUP.
altoparlante (in incrementi di 0,1 metri).
2 Usare / per selezionare unopzione
di impostazione.
T. TONE M. Spostare manualmente il Men Input Assign
test di prova da altoparlante ad
I parametri del menu Input Assign devono
altoparlante e regolare individualmente i
essere configurati solo nel caso in cui gli
livelli dei canali.
apparati digitali non siano stati collegati
T. TONE A. Regolare i livelli dei canali secondo le impostazioni predefinite per gli
quando il test di prova si sposta ingressi digitali.
automaticamente da un altoparlante allaltro.
3 Conffermare la selezione dellopzione Assegnazione degli ingressi digitali
dimpostazione. Impostazioni predefinite:
I toni di prova inizieranno a suonare appena COAX 1 (coassiale) DVD
premete ENTER.3 COAX 2 (coassiale) DVR
OPT 1 (ottico) CD
Nota
1 Se la qualit dei bassi non risulta soddisfacente, ascoltare la risposta dei bassi con il subwoofer impostato su PLUS e YES
oppure con gli altoparlanti frontali impostati alternativamente su LARGE e SMALL e verificare quale impostazione produce il
suono migliore. Se avete problemi, lopzione pi facile far passare tutti i suoni dei bassi al subwoofer selezionando SMALL per
gli altoparlanti anteriori.
2 Per ulteriori informazioni sulla selezione dei formati degli altoparlanti, vedi a Impostazione degli altoparlanti.
3 Quando il volume raggiunge il livello di riferimento, vengono emessi dei toni di prova.
4 Se si usa un misuratore del livello della pressione sonora (SPL), leggere la posizione dascolto principale e regolare il livello
di ogni altoparlante a 75 dB SPL (pesato C/lettura lenta).
Il tono di prova del subwoofer emesso ad un basso livello di volume. Pu essere necessario regolare il livello dopo il test
con una colonna sonora vera.
E possibile cambiare i livelli del canale in qualunque momento usando EFFECT/CH SEL e +/ sul telecomando. possibile
impostare due livelli di canale: uno per DVD 5.1 e uno per le modalit di ascolto.
5 Per ottenere un suono surround ottimale, accertarsi che il diffusore surround posteriore si trovi alla stessa distanza rispetto
alla posizione di ascolto.
36
It
VSX_516_Italian.fm Page 37 Friday, January 6, 2006 2:46 PM
Queste operazioni devono essere eseguite solo DUAL MONO Isolare un canale quando
nel caso in cui i componenti digitali non siano si ascoltano i dischi con codifica dual
stati collegati secondo le impostazioni mono (vedere Impostazione Dual Mono
predefinite sopraindicate. Questi parametri sotto).
indicano al ricevitore il componente collegato LFE ATT Impostare il livello attenuatore
a un terminale specifico, in modo che per il canale LFE (Impostazione LFE
corrisponda ai tasti del telecomando. Attenuator sotto).
English
1 Selezionare IN ASSIG. dal men System 3 Usare i tasti / per regolare ciascun
Setup. parametro, confermando con il tasto RETURN
al termine di ciascuna schermata.
2 Usare i tasti / per selezionare il
numero dellingresso digitale al quale si Impostazione di controllo della
collegato il componente digitale. gamma dinamica
Deutsch
I numeri corrispondono ai numeri allinterno Impostazione standard: OFF
degli ingressi sul retro del ricevitore. Consente di specificare la quantit di
3 Selezionare il componente che corrisponde regolazioni della gamma dinamica per le
colonne sonore Dolby Digital o DTS:
a quello collegato a quellingresso.
Usare i tasti / e ENTER per MAX La gamma dinamica ridotta (i
suoni forti hanno un volume ridotto,
Franais
selezionare DVD, TV, CD, CDR, DVR
oppure OFF. mentre i suoni silenziosi sono aumentati).
Se si assegna un ingresso digitale ad una MID Impostazione media.
certa funzione (ad esempio DVD) gli OFF Nessuna regolazione della gamma
ingressi digitali precedentemente dinamica (per ascoltare ad un alto livello
assegnati a quella funzione si del volume).
Italiano
spegneranno automaticamente.
Impostazione Dual Mono
4 Premere RETURN una volta terminato. Impostazione standard: CH1
Consente di specificare la modalit di
riproduzione delle colonne sonore Dolby
Menu di impostazione Other Digital con codifica dual mono:1
Nederlands
Il men Other serve per fare delle impostazioni CH2 Solo il canale 2 viene riprodotto
personalizzate secondo lutilizzo del ricevitore. CH1 CH2 Ambedue i canali sono
riprodotti attraverso gli altoparlanti anteriori
1 Selezionare OTHER dal men System
Setup. CH1 Solo il canale 1 viene riprodotto
Nota
1 Questimpostazione funziona solo con colonne sonore dual mono codificate Dolby Digital e DTS.
37
It
VSX_516_Italian.fm Page 38 Friday, January 6, 2006 2:46 PM
Capitolo 8:
Come usare il sintonizzatore
4 Premere ENTER per memorizzare la stazione.
Ascolto della radio Come denominare le stazioni
I seguenti punti spiegano come sintonizzare le preselezionate
stazioni radio FM e AM e come memorizzare le
possibile assegnare un nome alle stazioni di
frequenze per poterle richiamare preselezione in modo da poterle richiamare
successivamente. facilmente.
1 Premere AM o FM per selezionare la 1 Selezionare la stazione di preselezione a
banda di sintonizzazione desiderata. cui assegnare il nome.
Vedi a Ascolto delle stazioni preselezionate
2 Sintonizzare una stazione. sotto.
Ci sono tre modi per fare questo:
Sintonizzazione automatica Tenere 2 Premere (SHIF +) TUNER EDIT.
premuto TUNING +/ per un secondo Nella posizione del primo carattere viene
visualizzato un cursore.
circa. La ricerca automatica si interrompe
alla stazione successiva. 3 Inserire il nome desiderato, quindi premere
Sintonizzazione manuale Per cambiare ENTER.
I nomi possono essere lunghi fino a quattro
la frequenza di un passo per volta, premere caratteri.
TUNING +/.
Usare il comando MULTI JOG sul pannello
Sintonizzazione ad alta velocit Tenere frontale o i tasti STATION +/ sul telecomando
premuto TUNING +/ in modo continuativo. per selezionare i caratteri, quindi premere
Se il segnale debole, premere il tasto MPX ENTER per confermare. Se non inserito
per commutare il ricevitore sulla modalit di nessun carattere, viene inserito uno spazio.
ricezione mono.
Suggerimento
Una volta nominata una stazione di
Come salvare le stazioni di preselezione, si pu premere DISPLAY quando
preselezione si ascolta una stazione per commutare il display
Questo ricevitore in grado di memorizzare tra il nome e la frequenza.
fino a 30 stazioni, conservate in tre gruppi da
10 stazioni ciascuno.1
Ascolto delle stazioni preselezionate
E necessario aver memorizzato delle stazioni per
1 Sintonizzare la stazione da memorizzare. poter ascoltarle. Vedere Come salvare le stazioni
di preselezione a pagina 38 se non lo si gi fatto.
2 Premere (SHIFT +) TUNER EDIT.
Lindicazione ST. MEMORY appare sul 1 Premere AM o FM per selezionare il
display, seguita dalla classe che lampeggia. ricevitore.
3 Premere CLASS per selezionare una delle 2 Premere CLASS per selezionare la classe in
cui memorizzata la stazione.
tre classi e quindi premere STATION (+/) per Premere questo ripetutamente per cambiare
selezionare la stazione di preselezione tra le classi A, B e C.
desiderata.
Usare il comando MULTI JOG dopo aver 3 Premere STATION (+/) per selezionare la
premuto STATION (pannello frontale) per stazione di preselezione desiderata.
scegliere le stazioni di preselezione.
Nota
1 Quando si salva una frequenza FM, si salva anche limpostazione MPX.
38
It
VSX_516_Italian.fm Page 39 Friday, January 6, 2006 2:46 PM
English
spettacolo che stanno trasmettendo.
pressione del tasto:
Una funzione del RDS la possibilit di ricerca
per tipo di programma. Ad esempio, possibile Radio Text (RT): messaggi inviati da una
cercare una stazione che sta trasmettendo uno stazione radio. Ad esempio, un stazione
spettacolo con il tipo di programma, Jazz. radio di programmi parlati pu fornire un
possibile cercare i seguenti tipi di numero di telefono come RT.
Deutsch
programma:1 Program Service Name (PS): il nome della
stazione radio.
News Notizie Finance Notizie di borsa,
Affairs Attualit economia, commercio, Program Type (PTY): indica il tipo di
Info Informazioni ecc. programma in fase di trasmissione.
generali Children Programmi per
Frequenza corrente del sintonizzatore
Franais
Sport Sport bambini
Educate Programmi Social Affari sociali (FREQ).
educativi Religion Programmi
Drama Drammi sulla religione
radiofonici, ecc. Phone In Il pubblico Ricerca dei programmi RDS
Culture Cultura esprime la propria opinione possibile cercare un tipo di programma
nazionale o regionale, per telefono nellelenco precedente.
Italiano
teatro, ecc. Travel Viaggi di tipo
Science Scienze e vacanziero invece di notizie 1 Premere il tasto FM per selezionare la
tecnologia sul traffico
Varied Talk show, quali Leisure Tempo libero e banda FM.3
quiz o interviste. hobby
Pop M Musica pop Jazz Jazz 2 Premere PTY SEARCH (pannello frontale).
SEARCH appare sul display.
Nederlands
Rock M Musica rock Country Musica country
Easy M Musica leggera Nation M Musica
Light M Musica classica popolare in lingua diversa 3 Usare il controllo MULTI JOG per
leggera dallinglese selezionare il tipo del programma da ascoltare.
Classics Musica classica Oldies Musica popolare
seria degli anni 50 e 60 4 Premere ENTER per localizzare il tipo di
Other M Altri tipi di Folk M Musica folk programma.
musica che non rientrano Document Documentari Il sistema inizia la ricerca attraverso le stazioni
Espaol
nelle categorie di cui sopra preselezionate per trovare una corrispondenza.
Weather Previsioni del
Dopo la localizzazione della stazione, la ricerca
tempo
si ferma e la stazione viene riprodotta per
cinque secondi.
Nota
1 Inoltre, vi sono altri tre tipi di programmi: TEST, Alarm! e None. Alarm! e TEST sono usati per avvisi di emergenza. Non
possibile localizzare questo programma, ma il sintonizzatore cambia automaticamente a questo segnale di trasmissione RDS.
None appare nulla quando non si trova un tipo di programma.
2 Se viene assorbito del rumore durante la visualizzazione dello scorrimento RT, alcuni caratteri possono non essere
visualizzati correttamente.
Se si vede NO RADIO TEXT DATA sul display RT, significa che nessun dato RT inviato dalla stazione di trasmissione. Il
display passer automaticamente sul display di dati PS (in assenza di dati PS, viene visualizzata la frequenza).
Sul display PTY, potrebbe apparire NO DATA. In questo caso, il display PS viene mostrato dopo qualche secondo.
3 RDS possibile solo per la banda FM.
39
It
VSX_516_Italian.fm Page 40 Friday, January 6, 2006 2:46 PM
Nota
1 Il sistema RDS effettua la ricerca solo delle stazioni di preselezione. Se nessuna stazione stata preselezionata o se il tipo del
programma non stato trovato tra le stazioni di preselezione, lindicazione NO PTY appare sul display. FINISH significa che
stata completata la ricerca.
2 EON possibile solo nella banda FM.
3 Non possibile localizzare annunci sul traffico e notizie allo stesso tempo.
4 Non possibile usare i tasti TUNER EDIT e PTY SEARCH mentre illuminato lindicatore EON sul display.
Se desiderate cambiare ad una funzione che non sia quella del sintonizzatore quando lindicatore EON sta lampeggiando,
premere su EON MODE per disattivare EON.
40
It
VSX_516_Italian.fm Page 41 Friday, January 6, 2006 2:46 PM
Capitolo 9:
Come fare le registrazioni
Vedere le istruzioni in dotazione con il
Come fare una registrazione registratore se non si sa come procedere. La
English
maggior parte dei videoregistratori impostano
audio o video il livello di registrazione dellaudio
E possibile fare una registrazione audio o automaticamentecontrollare il manuale
video dal sintonizzatore incorporato o da delle istruzioni per ulteriori chiarimenti.
unaltra fonte audio o video collegata al
5 Avviare la registrazione, poi avviare la
Deutsch
ricevitore (ad esempio un lettore CD o un
televisore). riproduzione del componente fonte.
Non dimenticare che non possibile fare una
registrazione digitale da una fonte analogica o
viceversa, assicurarsi che i componenti usati
per la registrazione siano collegati nella stessa
Franais
maniera (vedi Collegamento a pagina 10 per
ulteriori informazioni sui collegamenti).
Italiano
Nederlands
Lillustrazione mostra il modello VSX-516
1 Selezionare la fonte da registrare.
Usare i tasti di selezione dellingresso (INPUT
SELECTOR).
2 Selezionare il segnale dingresso (se Espaol
necessario).
Premere SIGNAL SELECT (pannello frontale)
per selezionare il segnale di ingresso
corrispondente al componente sorgente
(consultare pagina 27 per maggiori dettagli).
3 Preparare la fonte da registrare.
Sintonizzare la stazione radio, inserire il CD, la
videocassetta, il DVD ecc.
4 Preparare il registratore.
Inserire una cassetta, un MD o una
videocassetta vergine nel dispositivo di
registrazione ed impostare i livelli di
registrazione.1
Nota
1 Il volume, il bilanciamento, il tono (bassi, acuti, loudness) e gli effetti surround non influiscono sul segnale registrato.
41
It
VSX_516_Italian.fm Page 42 Friday, January 6, 2006 2:46 PM
Capitolo 10:
Riproduzione USB
Uso dellinterfaccia USB Controlli di base per la
Solo per il modello VSX-516 riproduzione
possibile ascoltare audio a due canali 1 mediante La tabella che segue mostra i controlli di base
linterfaccia USB presente sul lato frontale del presenti sul telecomando per la riproduzione USB.
ricevitore. Collegare un dispositivo di archiviazione
di massa USB2 come indicato di seguito. Tasto Funzione
Avvia la normale riproduzione.
1 Premere USB (SHIFT+CD).
Mette in pausa/riprende la
2 Collegare il dispositivo USB. riproduzione.
Il terminale USB si trova sul pannello frontale. Premere per avviare la scansione con
3 Premere (riproduzione) per avviare la riavvolgimento rapido (premere due
volte per la scansione ad alta velocit).
riproduzione.
I file e le cartelle vengono riprodotti in ordine Premere per avviare la scansione con
sequenziale in base al nome dei file (secondo lo avanzamento rapido.
standard Unicode). Allinterno di ogni directory, (premere due volte per la scansione ad
vengono prima riprodotti tutti i file, per poi passare alta velocit).
al contenuto di cartelle e sottocartelle. Salta allinizio del brano corrente,
Nello schema che segue, la riproduzione quindi al brano precedente.
procede dalla cartella 0 alla cartella 5; vengono Salta al brano successivo.
riprodotti, in sequenza, i file da 1 a 8.
Importante
Se sul display viene visualizzato il messaggio
USB ERR provare a eseguire le operazioni
descritte di seguito:
USB ERR Cosa significa
USB ERR 1 I requisiti di alimentazione del
dispositivo USB sono troppo elevati per
questo ricevitore.
USB ERR 2 Il dispositivo USB non compatibile
USB ERR 3 Per maggiori dettagli su questo
Accertarsi che il ricevitore si trovi in messaggio di errore, consultare la
modalit standby quando si scollega il sezione Localizzazione dei guasti a
dispositivo USB. pagina 44.
42
It
VSX_516_Italian.fm Page 43 Friday, January 6, 2006 2:46 PM
English
lalimentazione USB. dallapplicazione usata per codificare i file
Se il problema persiste, probabile che il AAC. Questa unit riproduce i file AAC
dispositivo USB in uso non sia compatibile. codificati da iTunes, con estensione .m4a.
I file protetti con tecnologia DRM non vengono
Compatibilit dellaudio compresso riprodotti; inoltre, i file codificati con alcune
Si noti che, nonostante la compatibilit con la
Deutsch
versioni di iTunes potrebbero non essere
maggior parte delle combinazioni di velocit di
riprodotti.
bit/frequenza di campionamento standard per
laudio compresso, alcuni file con codifica Apple e iTunes sono marchi registrati di Apple
Computer, Inc. negli Stati Uniti e in altri Paesi.
irregolare potrebbero non esssere riprodotti.
Lelenco che segue indica i formati compatibili Informazioni su WMA
Franais
per i file audio compressi:
MP3 (MPEG-1/2/2.5 Audio Layer 3)
Frequenze di campionamento: 8 kHz a 48
kHz; velocit di bit: da 8 kbps a 320 kbps
(velocit consigliata: 128 Kbps o
superiore); estensione file: .mp3
Italiano
WMA (Windows Media Audio) Il logo Windows Media stampato sulla
Frequenze di campionamento: da 32 kHz / confezione indica che questo ricevitore in
44,1 kHz; velocit di bit: da 32 kbps a 192 grado di riprodurre file Windows Media Audio.
kbps (velocit consigliata: 128 Kbps o Lacronimo WMA sta per Windows Media
Nederlands
superiore); estensione file: .wma; WM9 Audio e si riferisce ad una tecnologia di
Pro e WMA con codifica lossless: No compressione dati audio sviluppata da
AAC (MPEG-4 Advanced Audio Coding) Microsoft Corporation. Questa unit riproduce
Frequenze di campionamento: 11,025 kHz i file WMA codificati usando Windows Media
a 48 kHz; velocit di bit: da 16 kbps a 320 Player, con estensione .wma. Si noti che i file
kbps (velocit consigliata: 128 Kbps o protetti con tecnologia DRM non vengono Espaol
superiore); estensione file: .m4a; Codifica riprodotti; inoltre, i file codificati con alcune
Apple lossless: No versioni di Windows Media Player potrebbero
non essere riprodotti.
Altre informazioni sulla compatibilit
Riproduzione a velocit di bit variabile VBR Microsoft, Windows Media e il logo di Windows sono
marchi di fabbrica o marchi di fabbrica registrati di
(Variable Bit Rate) MP3/WMA/MPEG-4
Microsoft Corporation negli Stati Uniti e/o in altri paesi.
AAC: S1
Compatibile con la tecnologia di protezione
DRM (Digital Rights Management): S (i file
audio protetti con tecnologia DRM non
vengono riprodotti con questo ricevitore).
Nota
1 Si noti che in alcuni casi il tempo di riproduzione potrebbe non essere visualizzato correttamente.
43
It
VSX_516_Italian.fm Page 44 Friday, January 6, 2006 2:46 PM
Capitolo 11:
Informazioni addizionali
Localizzazione dei guasti
Le operazioni errate sono spesso interpretate come problemi o malfunzionamenti. Se si sospetta
qualche problema nel componente, si prega di controllare i punti qui sotto. A volte, il problema
rimane in un altro componente. Esaminare gli altri componenti ed apparecchi elettrici usati. Se il
problema non pu essere rettificato anche dopo aver effettuato i controlli sopra descritti, chiedere
al centro di servizio Pioneer pi vicino o al proprio concessionario di svolgere i lavori di riparazione.
Se lunit non funziona in modo normale per via degli effetti esterni, quali lelettricit statica,
scollegare la spina dalimentazione dalla presa murale e ricollegarla per ritornare alle normali
condizioni duso.
Problema Rimedio
La corrente non si accende. Scollegare la spina del cavo dalimentazione dalla presa ed
inseritela nuovamente.
Assicurarsi che non vi siano cavi scollegati di altoparlanti che
toccano il pannello posteriore. Ci potrebbe fare spegnere
automaticamente il ricevitore.
Se lalimentazione si spegne automaticamente, portare lunit al
centro autorizzato o al concessionario Pioneer pi vicino per farla
aggiustare.
Non viene emesso suono Assicurarsi che il componente sia collegato correttamente (fare
quando selezionata una riferimento a Collegamento a pagina 10).
funzione. Premere MUTE sul telecomando per disattivare la funzione
corrispondente.
Non viene emessa alcuna Assicurarsi che il componente sia collegato correttamente (fare
immagine quando si seleziona riferimento a Collegamento a pagina 10).
una funzione. Selezionare il componente corretto (usare i tasti di selezione di
ingresso).
Notevole rumore nelle Collegare lantenna (pagina 15) e regolarne la posizione in modo da
trasmissioni radio. ottenere una ricezione ottimale.
Spostare i cavi scollegati dai terminali e dai fili dellantenna.
Allungare completamente lantenna FM a filo, posizionarla in modo
da ottenere una ricezione ottimale e fissarla a una parete (oppure
collegare unantenna FM esterna).
Collegare unantenna AM interna o esterna (fare riferimento a
pagina 15).
Spegnere le apparecchiature che causano interferenze o
posizionarli lontano dal ricevitore (oppure allontanare le antenne
dalle apparecchiature che causano interferenze).
Non possibile selezionare Collegare unantenna esterna (fare riferimento a pagina 15).
automaticamente le stazioni di
trasmissione.
Assenza di suono dagli Collegare correttamente gli altoparlanti (vedere pagina 16).
altoparlanti surround o Consultare Impostazione degli altoparlanti a pagina 35 per
centrali. controllare le impostazioni degli altoparlanti.
Fare riferimento Livello del canale a pagina 36 per controllare i livelli
dellaltoparlante.
44
It
VSX_516_Italian.fm Page 45 Friday, January 6, 2006 2:46 PM
Problema Rimedio
Assenza di audio dagli Fare riferimento a Impostazione degli altoparlanti a pagina 35 per
altoparlanti surround controllare le impostazioni dellaltoparlante posteriore surround.
posteriori. Fare riferimento Livello del canale a pagina 36 per controllare i livelli
dellaltoparlante.
Consultare Uso dellelaborazione del canale posteriore surround a
pagina 28 per accertarsi che lelaborazione del canale surround
English
posteriore e la modalit del suono siano impostate nel modo corretto
per il suono surround posteriore.
Deutsch
La fonte Dolby Digital o DTS che si sta ascoltando potrebbe non
avere un canale LFE.
Commutare limpostazione del subwoofer in Impostazione degli
altoparlanti a pagina 35 su YES o PLUS.
Commutare Impostazione LFE Attenuator a pagina 37 su LFEATT 0
o LFEATT 10.
Franais
Rumore durante la Spostare la piastra dal ricevitore finch non scompare il rumore.
riproduzione da una piastra a
cassette.
Non viene emesso alcun Impostare il livello del volume digitale del lettore al massimo o nella
suono o rumore alla posizione neutra.
Italiano
riproduzione di software con
DTS.
Nederlands
emette rumore.
Il display scuro o spento. Premere ripetutamente DIMMER sul telecomando per tornare
allimpostazione predefinita.
Il dispositivo USB non viene Accertarsi di aver inserito completamente il connettore USB nel ricevitore.
riconosciuto dal ricevitore. Verificare che il formato della memoria sia FAT16 o FAT32 (i formati FAT12,
NTFS e HFS non sono supportati).
I dispositivi USB dotati di hub USB interno non sono supportati.
Quando si collega un dispositivo Se il messaggio continua ad apparire dopo aver eseguito tutti i controlli
USB, sul display viene visualizzata riportati in Important on page 42 of USB playback, richiedere la riparazione
lindicazione USB ERR3 . dellunit presso il centro di assistenza autorizzato Pioneer pi vicino o
rivolgersi al proprio rivenditore.
I file WMA o MPEG-4 AAC non I file sono stati registrati usando la tecnologia per la protezione dalla copia
vengono riprodotti. DRM (Digital Rights Management) o FairPlay. Ci non dovuto ad un guasto.
45
It
VSX_516_Italian.fm Page 46 Friday, January 6, 2006 2:46 PM
46
It
VSX_516_Italian.fm Page 47 Friday, January 6, 2006 2:46 PM
English
Risposta di frequenza Documento di garanzia . . . . . . . . . . . . . . . . . . . 1
DVR/VCR, DVD/LD, Queste istruzioni per luso
TV/SAT MONITOR. . . . . . .5 Hz a 7 MHz dB
Rapporto segnale/rumore. . . . . . . . . . . . . . 55 dB Nota
Diafonia (crosstalk) . . . . . . . . . . . . . . . . . . . 50 dB Le specifiche ed il design sono soggetti a
Deutsch
possibili modifiche senza preavviso, per
Sezione del sintonizzatore FM motivi di miglioramenti del prodotto.
Gamma di frequenza . . . . . .87,5 MHz a 108 MHz
Sensibilit utile . . . . . . . . . . .Mono:13,2 dBf, IHF Pulizia dell'unit
(1,3 V/ 75 ) Usare un panno di pulizia o un panno
50 dB Sensibilit di silenziamento . . . . Mono: 20,2 dB
asciutto per rimuovere le tracce di polvere
Franais
Stereo: 38,6 dBf
e sporcizia.
Rapporto segnale/rumore . ..Mono: 73 dB (a 85 dBf)
Stereo: 70 dB (a 85 dBf) Quando la superficie sporca, strofinarla
Distorsione . . . . . . . . . . . . . Stereo: 0,5 % (1 kHz) con un panno soffice inumidito con un
Selettivit del canale alternativo . . . 60 dB (400 kHz) detergente neutro diluito cinque o sei volte
Separazione stereo . . . . . . . . . . . . .40 dB (1 kHz) con acqua e ben strizzato, poi passare un
Italiano
Risposta di frequenza . . . . . . . . . 30 Hz a 15 kHz panno asciutto sulla superficie. Non usare
(1 dB) mai cera per mobili o prodotti di pulizia.
Ingresso dellantenna (DIN) . . 75 asimmetrico Non usare mai acquaragia, benzina, spray
insetticida o altri prodotti chimici sopra o
Sezione del sintonizzatore AM nelle vicinanze di quest'unit, poich
Nederlands
Risposta di frequenza . . . . . . 531 Hz a 1 602 kHz possono corrodere la superficie della
Sensibilit (IHF, antenna a telaio) . . . . 350 V/m stessa.
Rapporto segnale/rumore. . . . . . . . . . . . . . 50 dB
Antenna . . . . . . . . . . . . . . . . . . . Antenna a telaio
Generalit Espaol
Requisiti di alimentazione
. . . . . . . . . . . . . . . . . . . . . AC 220 V a 230 V, 50 Hz/60 Hz
Consumo corrente
VSX-416. . . . . . . . . . . . . . . . . . . . . . . . . . . . .280 W
VSX-516. . . . . . . . . . . . . . . . . . . . . . . . . . . . .320 W
Nella modalit dattesa . . . . . . . . . . . . . . 0,5 W
Dimensioni
VSX-416 . . . 420 (W) mm x 158 (H) mm x 348 (D) mm
VSX-516 . . . . 420 (W) mm x 158 (H) mm x 352,5 (D) mm
Peso (senza imballaggio)
VSX-416. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8,5 kg
VSX-516. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8,9 kg
47
It
VSX_516_Italian.fm Page 48 Friday, January 6, 2006 2:46 PM
48
It
VSX_516_Italian.fm Page 49 Friday, January 6, 2006 2:46 PM
English
Deutsch
Franais
Italiano
Nederlands
Espaol
49
It
VSX_516_Italian.fm Page 50 Friday, January 6, 2006 2:46 PM
PIONEER CORPORATION
4-1, Meguro 1-Chome, Meguro-ku, Tokyo 153-8654, Japan
PIONEER ELECTRONICS (USA) INC.
P.O. BOX 1540, Long Beach, California 90810-1540, U.S.A. TEL: (800) 421-1404
PIONEER ELECTRONICS OF CANADA, INC.
300 Allstate Parkway, Markham, Ontario L3R OP2, Canada TEL: 1-877-283-5901
PIONEER EUROPE NV
Haven 1087, Keetberglaan 1, B-9120 Melsele, Belgium TEL: 03/570.05.11
PIONEER ELECTRONICS ASIACENTRE PTE. LTD.
253 Alexandra Road, #04-01, Singapore 159936 TEL: 65-6472-7555
PIONEER ELECTRONICS AUSTRALIA PTY. LTD.
178-184 Boundary Road, Braeside, Victoria 3195, Australia, TEL: (03) 9586-6300
PIONEER ELECTRONICS DE MEXICO S.A. DE C.V.
Blvd.Manuel Avila Camacho 138 10 piso Col.Lomas de Chapultepec, Mexico,D.F. 11000 TEL: 55-9178-4270
K002_A_En