Professional Documents
Culture Documents
Maxstar 140: With Auto-Link
Maxstar 140: With Auto-Link
Maxstar 140: With Auto-Link
February 1999
Processes
Stick (SMAW) Welding
Description
Maxstar 140 R
With Auto-Link
OM-2224
Y Marks a special safety message. This group of symbols means Warning! Watch Out! possible
ELECTRIC SHOCK, MOVING PARTS, and HOT PARTS hazards.
Consult symbols and related instructions below for necessary
. Means Note; not safety related. actions to avoid the hazards.
OM-2224 Page 1
Arc rays from the welding process produce intense D Shut off shielding gas supply when not in use.
visible and invisible (ultraviolet and infrared) rays D Always ventilate confined spaces or use
that can burn eyes and skin. Sparks fly off from the approved air-supplied respirator.
weld.
D Wear a welding helmet fitted with a proper shade of filter to protect
your face and eyes when welding or watching (see ANSI Z49.1
and Z87.1 listed in Safety Standards). HOT PARTS can cause severe burns.
D Wear approved safety glasses with side shields under your
helmet. D Do not touch hot parts bare handed.
D Use protective screens or barriers to protect others from flash and D Allow cooling period before working on gun or
glare; warn others not to watch the arc. torch.
D Wear protective clothing made from durable, flame-resistant
material (leather and wool) and foot protection.
MAGNETIC FIELDS can affect pacemakers.
WELDING can cause fire or explosion. D Pacemaker wearers keep away.
D Wearers should consult their doctor before
Welding on closed containers, such as tanks,
drums, or pipes, can cause them to blow up. Sparks going near arc welding, gouging, or spot
can fly off from the welding arc. The flying sparks, welding operations.
hot workpiece, and hot equipment can cause fires
and burns. Accidental contact of electrode to metal objects can
cause sparks, explosion, overheating, or fire. Check and be sure the
area is safe before doing any welding. NOISE can damage hearing.
D Protect yourself and others from flying sparks and hot metal.
Noise from some processes or equipment can
D Do not weld where flying sparks can strike flammable material. damage hearing.
D Remove all flammables within 35 ft (10.7 m) of the welding arc. If
this is not possible, tightly cover them with approved covers. D Wear approved ear protection if noise level is
high.
D Be alert that welding sparks and hot materials from welding can
easily go through small cracks and openings to adjacent areas.
D Watch for fire, and keep a fire extinguisher nearby.
D Be aware that welding on a ceiling, floor, bulkhead, or partition CYLINDERS can explode if damaged.
can cause fire on the hidden side.
D Do not weld on closed containers such as tanks, drums, or pipes, Shielding gas cylinders contain gas under high
pressure. If damaged, a cylinder can explode.
unless they are properly prepared according to AWS F4.1 (see Since gas cylinders are normally part of the welding
Safety Standards). process, be sure to treat them carefully.
D Connect work cable to the work as close to the welding area as
practical to prevent welding current from traveling long, possibly D Protect compressed gas cylinders from excessive heat,
unknown paths and causing electric shock and fire hazards. mechanical shocks, slag, open flames, sparks, and arcs.
D Do not use welder to thaw frozen pipes. D Install cylinders in an upright position by securing to a stationary
support or cylinder rack to prevent falling or tipping.
D Remove stick electrode from holder or cut off welding wire at
contact tip when not in use. D Keep cylinders away from any welding or other electrical circuits.
D Wear oil-free protective garments such as leather gloves, heavy D Never drape a welding torch over a gas cylinder.
shirt, cuffless trousers, high shoes, and a cap. D Never allow a welding electrode to touch any cylinder.
D Remove any combustibles, such as a butane lighter or matches, D Never weld on a pressurized cylinder explosion will result.
from your person before doing any welding.
D Use only correct shielding gas cylinders, regulators, hoses, and
fittings designed for the specific application; maintain them and
associated parts in good condition.
FLYING METAL can injure eyes.
D Turn face away from valve outlet when opening cylinder valve.
D Welding, chipping, wire brushing, and grinding D Keep protective cap in place over valve except when cylinder is in
cause sparks and flying metal. As welds cool, use or connected for use.
they can throw off slag.
D Read and follow instructions on compressed gas cylinders,
D Wear approved safety glasses with side associated equipment, and CGA publication P-1 listed in Safety
shields even under your welding helmet. Standards.
OM-2224 Page 2
OM-2224 Page 3
OM-2224 Page 4
Un simple contact avec des pices lectriques peut Il y a DU COURANT CONTINU IMPORTANT dans les
provoquer une lectrocution ou des blessures graves. convertisseurs aprs la suppression de lalimenta-
Llectrode et le circuit de soudage sont sous tension
ds que lappareil est sur ON. Le circuit dentre et les tion lectrique.
circuits internes de lappareil sont galement sous
tension ce moment-l. En soudage semi-automatique ou automatique, D Arrter les convertisseurs, dbrancher le courant lectrique, et d-
le fil, le dvidoir, le logement des galets dentranement et les pices charger les condensateurs dalimentation selon les instructions
mtalliques en contact avec le fil de soudage sont sous tension. Des indiques dans la partie entretien avant de toucher les pices.
matriels mal installs ou mal mis la terre prsentent un danger.
D Ne jamais toucher les pices lectriques sous tension.
D Porter des gants et des vtements de protection secs ne comportant
pas de trous.
D Sisoler de la pice et de la terre au moyen de tapis ou dautres LES FUMES ET LES GAZ peuvent
moyens isolants suffisamment grands pour empcher le contact phy- tre dangereux.
sique ventuel avec la pice ou la terre. Le soudage gnre des fumes et des gaz. Leur
D Ne pas se servir de source lectrique courant lectrique dans les zones inhalation peut tre dangereux pour votre sant.
humides, dans les endroits confins ou l o on risque de tomber.
D Se servir dune source lectrique courant lectrique UNIQUEMENT si le D Eloigner votre tte des fumes. Ne pas respirer
procd de soudage le demande. les fumes.
D Si lutilisation dune source lectrique courant lectrique savre nces-
D A lintrieur, ventiler la zone et/ou utiliser un chappement au ni-
saire, se servir de la fonction de tlcommande si lappareil en est quip. veau de larc pour lvacuation des fumes et des gaz de soudage.
D Couper lalimentation ou arrter le moteur avant de procder linstal- D Si la ventilation est insuffisante, utiliser un respirateur alimenta-
lation, la rparation ou lentretien de lappareil. Dverrouiller tion dair homologu.
lalimentation selon la norme OSHA 29 CFR 1910.147 (voir normes D Lire les spcifications de scurit des matriaux (MSDSs) et les ins-
de scurit). tructions du fabricant concernant les mtaux, les consommables,
D Installer et mettre la terre correctement cet appareil conformment les revtements, les nettoyants et les dgraisseurs.
son manuel dutilisation et aux codes nationaux, provinciaux et D Travailler dans un espace ferm seulement sil est bien ventil ou
municipaux. en portant un respirateur alimentation dair. Demander toujours
D Toujours vrifier la terre du cordon dalimentation Vrifier et sassu- un surveillant dment form de se tenir proximit. Des fumes et
rer que le fil de terre du cordon dalimentation est bien raccord la des gaz de soudage peuvent dplacer lair et abaisser le niveau
borne de terre du sectionneur ou que la fiche du cordon est raccorde doxygne provoquant des blessures ou des accidents mortels.
une prise correctement mise la terre. Sassurer que lair de respiration ne prsente aucun danger.
D Ne pas souder dans des endroits situs proximit doprations de
D En effectuant les raccordements dentre fixer dabord le conducteur
dgraissage, de nettoyage ou de pulvrisation. La chaleur et les
de mise la terre appropri et contre-vrifier les connexions.
rayons de larc peuvent ragir en prsence de vapeurs et former
D Vrifier frquemment le cordon dalimentation pour voir sil nest pas des gaz hautement toxiques et irritants.
endommag ou dnud remplacer le cordon immdiatement sil est
D Ne pas souder des mtaux munis dun revtement, tels que lacier
endommag un cble dnud peut provoquer une lectrocution.
galvanis, plaqu en plomb ou au cadmium moins que le revte-
D Mettre lappareil hors tension quand on ne lutilise pas. ment nait t enlev dans la zone de soudure, que lendroit soit
D Ne pas utiliser des cbles uss, endommags, de grosseur insuffi- bien ventil, et si ncessaire, en portant un respirateur alimenta-
sante ou mal pisss. tion dair. Les revtements et tous les mtaux renfermant ces l-
D Ne pas enrouler les cbles autour du corps. ments peuvent dgager des fumes toxiques en cas de soudage.
D Si la pice soude doit tre mise la terre, le faire directement avec un
cble distinct ne pas utiliser le connecteur de pice ou le cble de
retour.
OM-2224 Page 5
Downloaded from www.Manualslib.com manuals search engine
LES RAYONS DE LARC peuvent pro- LES ACCUMULATIONS DE GAZ ris-
voquer des brlures dans les yeux et quent de provoquer des blessures ou
sur la peau. mme la mort.
Le rayonnement de larc du procd de soudage
gnre des rayons visibles et invisibles intenses D Fermer lalimentation du gaz protecteur en cas de
(ultraviolets et infrarouges) susceptibles de provoquer non utilisation.
des brlures dans les yeux et sur la peau. Des tincelles sont projetes D Veiller toujours bien arer les espaces confins ou se servir dun respi-
pendant le soudage. rateur dadduction dair homologu.
D Porter un casque de soudage muni dun cran de filtre appropri pour
protger votre visage et vos yeux pendant le soudage ou pour regar-
der (voir ANSI Z49.1 et Z87.1 numr dans les normes de scurit).
D Porter des protections approuvs pour les oreilles si le niveau sondre est
DES PICES CHAUDES peuvent pro-
trop lev. voquer des brlures graves.
D Utiliser des crans ou des barrires pour protger des tiers de lclair
et de lblouissement; demander aux autres personnes de ne pas re- D Ne pas toucher des parties chaudes mains
garder larc. nues
D Porter des vtements de protection constitu dans une matire dura- D Prvoir une priode de refroidissement avant
ble, rsistant au feu (cuir ou laine) et une protection des pieds. dutiliser le pistolet ou la torche.
OM-2224 Page 6
Downloaded from www.Manualslib.com manuals search engine
1-3. Dangers supplmentaires en relation avec linstallation, le fonctionnement
et la maintenance
OM-2224 Page 7
Downloaded from www.Manualslib.com manuals search engine
1-4. Principales normes de scurit
Safety in Welding and Cutting, norme ANSI Z49.1, de lAmerican Wel- Safe Handling of Compressed Gases in Cylinders, CGA Pamphlet
ding Society, 550 N.W. Lejeune Rd, Miami FL 33126 P-1, de la Compressed Gas Association, 1235 Jefferson Davis High-
way, Suite 501, Arlington, VA 22202.
Safety and Health Sandards, OSHA 29 CFR 1910, du Superintendent
of Documents, U.S. Government Printing Office, Washington, D.C. Rgles de scurit en soudage, coupage et procds connexes, nor-
20402. me CSA W117.2, de lAssociation canadienne de normalisation, vente
de normes, 178 Rexdale Boulevard, Rexdale (Ontario) Canada M9W
Recommended Safe Practice for the Preparation for Welding and Cut- 1R3.
ting of Containers That Have Held Hazardous Substances, norme Safe Practices For Occupation And Educational Eye And Face Protec-
AWS F4.1, de lAmerican Welding Society, 550 N.W. Lejeune Rd, Mia- tion, norme ANSI Z87.1, de lAmerican National Standards Institute,
mi FL 33126 1430 Broadway, New York, NY 10018.
National Electrical Code, NFPA Standard 70, de la National Fire Pro- Cutting and Welding Processes, norme NFPA 51B, de la National Fire
tection Association, Batterymarch Park, Quincy, MA 02269. Protection Association, Batterymarch Park, Quincy, MA 02269.
OM-2224 Page 8
Downloaded from www.Manualslib.com manuals search engine
SECTION 2 SPECIFICATIONS AND INSTALLATION
2-1. Specifications
Amperes
Input Input At
KVA
Power Rated
Welding Maximum AT
Rated Welding Load
Single- Amperage Open-Circuit 100% KW Dimensions Weight
Output Output,
Phase Range Voltage DC Duty
50/60Hz,
AC Cyc.
Single-
Phase
2-2. Description
1 Welding Power Source
This unit is a compact, light weight,
portable welding power source
containing the latest high perfor-
1 mance electronics that supplies
DC weld output for use with the
Stick Electrode and TIG welding
processes.
This unit also has a carrying strap
and quick-disconnect weld output
receptacles to aid portability and to
encourage use wherever the job
may be located. Because of its
electronic design, this unit con-
sumes only modest amounts of in-
put power and provides superb arc
characteristics. Further, it is easy
to install and simple to operate.
This welding power source is
equipped with the advanced Auto-
Link circuitry which automatically
adjusts the unit to operate from the
available input voltage without
making any internal changes. The
circuitry works with either 115 or
230 volts input power.
DP-00400
OM-2224 Page 9
DP-00401
3
4
DP-00401
OM-2224 Page 10
110 A @ 35% Duty Cycle (115 V Input) 80 A @ 100% Duty Cycle (115 V Input)
140 A @ 25% Duty Cycle (230 V Input) 100 A @ 100% Duty Cycle (230 V Input)
Overheating
0 A or V
15
OR
Minutes Reduce Duty Cycle
193 116
OM-2224 Page 11
Stick Min.
TIG Min.
OM-2224 Page 12
18 in
(460 mm)
2
Airflow Distance
Requirements
18 in
(460 mm)
ETP-1400-PDF
OM-2224 Page 13
1 Rear Panel
1 2 Power On/Off Switch
Rotate the Power Switch to the On
or Off position as needed accord-
2 ing to the markings on the rear pan-
el.
3 Input Power Cord
DP-00335
OM-2224 Page 14
1
Ref.ST-157 357-C / DP-00400
OM-2224 Page 15
4
3
6
Tools Needed:
DP-00333
Y Disconnect input power plug from Loosen strain relief clamp, and push sever- 7 Green Ground Lead
receptacle before installing differ- al inches of power cord into unit.
ent input power cord. Insert new power cord through strain relief,
Mark location of switch terminals where and push an extra inch into unit.
Remove the case by removing the two top black and white leads are connected, and
handle screws and sliding case up and off. note location of ground lead. Disconnect Connect ground lead and black and white
Disconnect case grounding wire when re- leads from ground terminal and switch. leads to marked locations. Double-check all
moving case. 2 Black Switch Lead connections.
1 Input Power Cord 3 Rear Panel Reinstall Power Switch onto rear panel. Pull
Remove knob from Power Switch (4). Note 4 Power Switch power cord back through strain relief until
how knob goes onto shaft. leads are properly dressed in unit. Tighten
Pull out power cord from rear of unit. clamp.
Remove screws holding Power Switch in
5 Case Grounding Lead
place, and pull switch out toward inside of Reinstall case and reconnect case ground-
unit. 6 White Lead ing lead during assembly.
OM-2224 Page 16
6
4
1 Ready Light a dual reading dial. Be sure to set it ac- check electrode recommendations.) For
This light comes On when the Power cording to the input voltage supplying TIG welding, connect work cable to this re-
Switch on the rear panel is placed in the power to the unit. ceptacle (normally uses straight polarity).
ON position. The light indicates that the 3 Overtemperature Light 5 STICK / TIG Selector Switch
unit is energized and ready for welding op-
erations. This light comes ON when the unit over- This switch provides a simple and easy
heats. When this happens, the unit shuts way to select the required welding pro-
. The fan motor is thermostatically down and the fan motor runs. Once the unit cess. Place the switch in the desired posi-
controlled and only runs when cooling has cooled down, the output will come tion to suit the application. This switch is
is needed. back ON. Reduce the duty cycle or amper- NOT a Polarity Switch. This switch acti-
2 Amperage Adjustment Control age before starting to weld again. This vates the Lift Arc circuit.
This control adjusts the desired amperage light flashes if the input voltage (primary) is
6 Negative Weld Output Recptacle
for the welding application. Use this control too low or if there is an input overcurrent
to set the required value for the specific job fault. For STICK welding, connect the work
and electrode. The dial is calibrated in ac- cable to this receptacle (normally uses re-
4 Positive Weld Output Receptacle
tual amperes according to the input volt- verse polartiy connections, but always
age used to power the unit. For STICK welding, connect the electrode check electrode recommendations.) For
cable to this receptacle (normally uses re- TIG welding, connect torch cable to this re-
. The Amperage Adjustment Control is verse polartiy connections, but always ceptacle (normally uses straight polarity).
192 999
OM-2224 Page 17
3 Months
3 Months
Repair Or Replace
Cracked Cables
And Cords
6 Months
Y Do not remove case when
blowing out inside of unit
(see Section 4-2) .
Blow out inside. During
heavy service clean
monthly.
OM-2224 Page 18
DP-00333
OM-2224 Page 19
Trouble Remedy
No weld output; unit completely inop- Place line disconnect switch for circuit powering welder in On position.
erative; Ready light Off.
Be sure input power cord is plugged in and that receptacle is receiving input power.
No weld output; Ready light On; Over- Check and secure loose weld cable(s) into receptacle(s) on welding power source.
Temperature light Off.
No weld output; Ready light On; Over- Unit overheated causing thermal shutdown. Allow unit to cool with fan On (see Section 2-5).
Temperature light On.
Check and correct blocked/poor airflow to and around unit or move unit clear of blockages (see
Section 2-7).
No weld output; Ready light On; Over- Turn Power Switch Off and back On again. If light continues to flash, call or take machine to Facto-
Temperature light Flashing. ry Authorized Service Agent (this condition may indicate a fault in the power section).
Erratic or improper welding arc or out- Use proper size and type of weld cable (see your Distributer).
put.
Check and reverse electrode polarity; check and correct poor connections to workpiece.
Fan not operating (unit is equipped Unit is cool and not warmed up enough to require fan cooling.
with Fan-On-Demand so fan runs only
when needed).
Have Factory Authorized Service Agent check fan motor and control circuitry.
Stick welding problems: Hard starts; Use proper type and size of electrode.
poor welding characteristcs; unusual
spattering problems. Use method shown in Section 8 to get better starts.
Check and reverse electrode polarity; check and correct poor connections to workpiece.
TIG welding problems: Wandering arc; Use proper type and size of tungsten.
hard starts; poor welding character-
istcs; spattering problems. Use properly prepared tungsten.
Check and reverse electrode polarity; check and correct poor connections to workpiece.
TIG welding problems: Tungsten elec- Shield weld zone from drafts.
trode oxidizing and not remaining bright
after conclusion of weld. Check shielding gas supply, and be sure it is the correct type (argon) and that the cylinder is not empty.
Check and change electrode polarity; move Changeover Switch to TIG position.
OM-2224 Page 20
C-193 705
Tools Needed:
OM-2224 Page 22
AMPERAGE
RANGE
ELECTRODE
DIAMETER
100
150
200
250
300
350
400
450
PENETRATION
50
ELECTRODE
POSITION
USAGE
3/32
DC*
AC
1/8
6010
5/32
& 3/16
6011 7/32
1/4 6010 EP ALL DEEP MIN. PREP, ROUGH
1/16 HIGH SPATTER
6011 EP ALL DEEP
5/64
3/32 6013 EP,EN ALL LOW GENERAL
1/8 SMOOTH, EASY,
6013 7014 EP,EN ALL MED FAST
5/32
3/16 LOW HYDROGEN,
7018 EP ALL LOW STRONG
7/32
1/4 FLAT
7024 EP,EN HORIZ LOW SMOOTH, EASY,
3/32 FASTER
FILLET
1/8
5/32 NI-CL EP ALL LOW CAST IRON
7014
3/16 308L EP ALL LOW STAINLESS
7/32 *EP = ELECTRODE POSITIVE (REVERSE POLARITY)
1/4 EN = ELECTRODE NEGATIVE (STRAIGHT POLARITY)
3/32
1/8
5/32
7018
3/16
7/32
1/4
3/32
1/8
5/32
7024
3/16
7/32
1/4
3/32
1/8
Ni-Cl
5/32
3/16
3/32
308L 1/8
5/32
Ref. S-087 985-A
S-0050
OM-2224 Page 23
90 90
GROOVE WELDS
10-30
45
45
2 3 4
5 S-0053-A
S-0052-B
OM-2224 Page 24
NOTE Weld bead shape is affected by electrode angle, arc length, travel speed, and
thickness of base metal.
Correct Angle
Angle Too Small 10 - 30 Angle Too Large
Drag
ELECTRODE ANGLE
Spatter
NOTE Normally, a single stringer bead is satisfactory for most narrow groove weld joints;
however, for wide groove weld joints or bridging across gaps, a weave bead or
multiple stringer beads work better.
S-0054-A
OM-2224 Page 25
S-0662
3
S-0060 / S-0058-A / S-0061
OM-2224 Page 26
S-0057-B
Workpiece dirty. Remove all grease, oil, moisture, rust, paint, coatings, slag, and dirt from work surface before
welding.
Amperage too high for electrode. Decrease amperage or select larger electrode.
Arc length too long or voltage too high. Reduce arc length or voltage.
OM-2224 Page 27
Insufficient heat input. Increase amperage. Select larger electrode and increase amperage.
Improper welding technique. Place stringer bead in proper location(s) at joint during welding.
Momentarily hold arc on groove side walls when using weaving technique.
Workpiece dirty. Remove all grease, oil, moisture, rust, paint, coatings, slag, and dirt from work surface before
welding.
Improper joint preparation. Material too thick. Joint preparation and design must provide access to bottom of groove.
Insufficient heat input. Increase amperage. Select larger electrode and increase amperage.
OM-2224 Page 28
Waviness Of Bead weld metal that is not parallel and does not cover
joint formed by base metal.
Excessive heat input. Use restraint (clamp) to hold base metal in position.
OM-2224 Page 29
NOTE For additional information, see your distributor for a handbook on the Gas
Tungsten Arc Welding (GTAW) process. Wear clean gloves to prevent
contamination of tungsten electrode.
Typical argon shielding gas flow rates are 15 to 35 cfh (cubic feet per hour) 7 to 16.5 lpm (liters per minute).
*Not Recommended.
The figures listed are intended as a guide and are a composite of recommendations from American Welding Society (AWS) and electrode
manufacturers.
OM-2224 Page 30
2-1/2 Times
Electrode Diameter
1 Stable Arc
2 Flat
1
Diameter of this flat determines
amperage capacity.
2
3 Grinding Wheel
3 4 Straight Ground
4
Ideal Tungsten Preparation Stable Arc
1 Arc Wander
2 Point
1 3 Grinding Wheel
4 Radial Ground
2
OM-2224 Page 31
OM-2224 Page 32
Welding direction 75
75 15
Welding direction
OM-2224 Page 33
90
Butt Weld And Stringer Bead
70
20
20
T Joint
70
20
10
40
Lap Joint
70
20
30
90
Corner Joint
70
20
OM-2224 Page 34
OM-2224 Page 35
1 2
15
16
3
13
14
11, 12
4
10 5
9
. Hardware is common and
not available unless listed. DP-00331
To maintain the factory original performance of your equipment, use only Manufacturers Suggested
Replacement Parts. Model and serial number required when ordering parts from your local distributor.
OM-2224 Page 36
15
10
14
. Hardware is common and 13 11
not available unless listed. 12
DP-00346
To maintain the factory original performance of your equipment, use only Manufacturers Suggested
Replacement Parts. Model and serial number required when ordering parts from your local distributor.
OM-2224 Page 37
DP-00347
OM-2224 Page 38
tor....
you
Within the warranty periods listed below, Miller will repair or 3. Equipment that has been modified by any party other
than Miller, or equipment that has been improperly
Service replace any warranted parts or components that fail due to
such defects in material or workmanship. Miller must be installed, improperly operated or misused based upon
You always get the fast, industry standards, or equipment which has not had
reliable response you notified in writing within thirty (30) days of such defect or
failure, at which time Miller will provide instructions on the reasonable and necessary maintenance, or equipment
need. Most replacement warranty claim procedures to be followed. which has been used for operation outside of the
parts can be in your specifications for the equipment.
hands in 24 hours. Miller shall honor warranty claims on warranted equipment
MILLER PRODUCTS ARE INTENDED FOR PURCHASE
listed below in the event of such a failure within the warranty
Support time periods. All warranty time periods start on the date that AND USE BY COMMERCIAL/INDUSTRIAL USERS AND
PERSONS TRAINED AND EXPERIENCED IN THE USE
Need fast answers to the the equipment was delivered to the original retail purchaser,
or one year after the equipment is sent to a North American AND MAINTENANCE OF WELDING EQUIPMENT.
tough welding questions?
Contact your distributor. distributor or eighteen months after the equipment is sent to In the event of a warranty claim covered by this warranty, the
an International distributor. exclusive remedies shall be, at Millers option: (1) repair; or
The expertise of the
(2) replacement; or, where authorized in writing by Miller in
distributor and Miller is 1. 1 Year Parts and Labor appropriate cases, (3) the reasonable cost of repair or
there to help you, every * Maxstar 140 replacement at an authorized Miller service station; or (4)
step of the way. payment of or credit for the purchase price (less reasonable
* Motor Driven Guns (w/exception of Spoolmate 185)
depreciation based upon actual use) upon return of the
* Process Controllers goods at customers risk and expense. Millers option of
* Positioners and Controllers repair or replacement will be F.O.B., Factory at Appleton,
Wisconsin, or F.O.B. at a Miller authorized service facility as
* Automatic Motion Devices determined by Miller. Therefore no compensation or
* Robots reimbursement for transportation costs of any kind will be
allowed.
* IHPS Power Sources
* Water Coolant Systems TO THE EXTENT PERMITTED BY LAW, THE REMEDIES
PROVIDED HEREIN ARE THE SOLE AND EXCLUSIVE
* HF Units REMEDIES. IN NO EVENT SHALL MILLER BE LIABLE
* Grids FOR DIRECT, INDIRECT, SPECIAL, INCIDENTAL OR
CONSEQUENTIAL DAMAGES (INCLUDING LOSS OF
* Spot Welders PROFIT), WHETHER BASED ON CONTRACT, TORT OR
* Load Banks ANY OTHER LEGAL THEORY.
* SDX Transformers ANY EXPRESS WARRANTY NOT PROVIDED HEREIN
* Miller Cyclomatic Equipment AND ANY IMPLIED WARRANTY, GUARANTY OR
REPRESENTATION AS TO PERFORMANCE, AND ANY
* Running Gear/Trailers REMEDY FOR BREACH OF CONTRACT TORT OR ANY
* Plasma Cutting Torches (except APT, ZIPCUT & OTHER LEGAL THEORY WHICH, BUT FOR THIS
PLAZCUT Models) PROVISION, MIGHT ARISE BY IMPLICATION,
OPERATION OF LAW, CUSTOM OF TRADE OR COURSE
* Deutz Engines (outside North America) OF DEALING, INCLUDING ANY IMPLIED WARRANTY OF
* Field Options MERCHANTABILITY OR FITNESS FOR PARTICULAR
(NOTE: Field options are covered under True Blue PURPOSE, WITH RESPECT TO ANY AND ALL
for the remaining warranty period of the product they EQUIPMENT FURNISHED BY MILLER IS EXCLUDED
are installed in, or for a minimum of one year AND DISCLAIMED BY MILLER.
whichever is greater.)
Some states in the U.S.A. do not allow limitations of how long
2. 6 Months Batteries an implied warranty lasts, or the exclusion of incidental,
indirect, special or consequential damages, so the above
3. 90 Days Parts and Labor limitation or exclusion may not apply to you. This warranty
provides specific legal rights, and other rights may be
* MIG Guns/TIG Torches
available, but may vary from state to state.
* APT, ZIPCUT & PLAZCUT Model Plasma Cutting
Torches In Canada, legislation in some provinces provides for certain
additional warranties or remedies other than as stated
* Remote Controls herein, and to the extent that they may not be waived, the
* Accessory Kits limitations and exclusions set out above may not apply. This
Limited Warranty provides specific legal rights, and other
* Replacement Parts (No labor) rights may be available, but may vary from province to
* Spoolmate 185 province.
miller_warr 1/98
Distributor
Address
City
State Zip
Resources Available
Always provide Model Name and Serial/Style Number.
Contact the Delivering Carrier for: File a claim for loss or damage during
shipment.
For assistance in filing or settling claims,
contact your distributor and/or equipment
manufacturers Transportation Department.