Professional Documents
Culture Documents
GENEX Probe&Assistant V300R017C00 Terminal Operation Guide (HUAWEI ATH)
GENEX Probe&Assistant V300R017C00 Terminal Operation Guide (HUAWEI ATH)
V300R017C00
Terminal Operation Guide
(HUAWEI ATH)
Issue 01
Date 2017-01-06
and other Huawei trademarks are trademarks of Huawei Technologies Co., Ltd.
All other trademarks and trade names mentioned in this document are the property of their respective
holders.
Notice
The purchased products, services and features are stipulated by the contract made between Huawei and
the customer. All or part of the products, services and features described in this document may not be
within the purchase scope or the usage scope. Unless otherwise specified in the contract, all statements,
information, and recommendations in this document are provided "AS IS" without warranties, guarantees
or representations of any kind, either express or implied.
The information in this document is subject to change without notice. Every effort has been made in the
preparation of this document to ensure accuracy of the contents, but all statements, information, and
recommendations in this document do not constitute a warranty of any kind, express or implied.
Website: http://www.huawei.com
Email: support@huawei.com
Related Personnel
Prepared by Date
Reviewed By Date
Tested By Date
Approved By Date
Change History
Contents
4 FAQs...............................................................................................................................................19
4.1 FAQ-01.........................................................................................................................................................................19
4.2 FAQ-02.........................................................................................................................................................................19
4.3 FAQ-03.........................................................................................................................................................................19
4.4 FAQ-04.........................................................................................................................................................................20
4.5 FAQ-05.........................................................................................................................................................................20
4.6 FAQ-06.........................................................................................................................................................................23
4.7 FAQ-07.........................................................................................................................................................................23
1 Overview
After the manufacture mode is enabled on a HUAWEI Honor 7i to connect to the GENEX
Probe, the RNDIS network adapter is unavailable. As a result, the USB tethering cannot be
used during tests. The RAS dial speed is about 40 Mbit/s.
If the RAS dial speed is not considered, the mobile phones whose models are as follows can
be used for tests:
ATH-AL00, ATH-UL01, and ATH-UL06
If the mobile phone versions are as follows, the USB tethering can be used, the RNDIS
network adapter can be enabled through configurations, and these phones can be connected to
the GENEX Probe:
ATH-AL00C00B140 or later
ATH- UL01C432B150
ATH-UL06C469B130
You can touch Setting > About Phone > Build number to view the mobile phone version
number.
2.1 Preparations
Material Description Obtaining Method
Root package Consists of the Honor 7i Contact the DPM of the corresponding
used to enable root package and the region to obtain the download address.
USB tethering in RDNIS port
one-click mode configuration file and
scripts.
Driver Driver
Handset WinDriver_2.00.10.00.rar
Qualcomm The unlock code type is Huawei employees: contact the local
background NCK_DIAGUNLOCK. terminal service manager to obtain the
unlock code code; alternatively, sent the IMEI of the
(NCK_DIAGUN test mobile phone to pa_phu@huawei.com
LOCK code) by mail for application.
Non-Huawei employees: provide the
IMEI of the test mobile phone to local
Huawei engineers and ask their help for
application.
Notice:pa_phu@huawei.com just deal
with unlock code application every
Friday,please apply it before Friday.
Forcing function Used to implement
APK forcing functions.
ForceFunction_V1.
3.rar
----End
Step 4 Touch Background Settings. On the displayed screen, touch Background Debug.
The Background Debug dialog box is displayed.
Step 5 Select Open.
The Input Password dialog box is displayed.
Skip this step if Open has been selected for Background Debug.
----End
----End
If the Allow USB debugging dialog box is displayed, select Always allow from this
computer and click OK.
When you perform operations provided in section 2.4"(Optional) Enabling the RNDIS
Network Adapter," select Always allow from this computer if the Allow USB debugging
dialog box is displayed. If it is not selected, the script execution will fail.
----End
Perform operations provided in this section to enable the RNDIS network adapter in the
manufacture mode, enable USB tethering during Probe connection, and resolve the limited
RAS dialing speed problem. Skip this section if the data service test is not required or the
live-network throughput is less than 40 Mbit/s.
Ignore the error message "SogouPhoneService.exe not found" and pay attention to other error
messages in this window.
If the following error messages are displayed, ensure that you have correctly performed the
steps in sections 2.3.2and 2.3.3"device offline", "device not found", or "error: device
unauthorized. Please check the confirmation dialog on your device."
----End
Before performing the steps in this section, ensure that the version of the mobile phone is
consistent with that of the root package because the inconsistency will result in phone
powered-on failure. If they are inconsistent, contact the DPM to obtain the correct root
package.
Step 15 Ensure that the ADB test environment has been installed properly.
Step 16 Decompress the root package used to enable USB tethering in one-click mode, and run
02.root.bat.
----End
----End
Step 3 Open the build.prop file in the D:\ directory. Search for the field ro.config.hw_channel_info.
Change its value to 1,0,460,1,1, and add the attribute ro.config.persist_usb_tethering=true
before the field ro.config.hw_USB_on_enable_FD=true, as shown in the following figures.
Step 4 Run the following ADB commands one by one to replace the file in the terminal system with
the modified one:
adb remount
adb push D:\build.prop /system/
adb shell chmod 644 /system/build.prop
----End
If the Remote NDIS based Internet Sharing Device port of the terminal on which the RNDIS
network adapter and USB tethering have been enabled is unavailable, see section 4.4"FAQ-
04."
----End
Step 12 Configure parameters. Set Type to MS, Model to HUAWEI Athena, and select the default
value from the Modem port drop-down list. If no default value is available, reinstall the
driver or set the terminal. Set Com port to a required value (for details about how to query
the Com port, see the next step). After the configuration is complete, click OK.
Step 13 Right-click My Computer and choose Computer Management from the shortcut menu. In
the Computer Management window, click Device Manager and obtain the port number of
the preceding port.
Step 14 (Optional) Click in the Device Configure window to automatically search for terminals,
as shown in the following figure.
----End
----End
The USB tethering can be enabled only on the terminal whose RNDIS network adapter is
enabled. Ensure that data services are enabled before tests.
In the test plan, configure the FTP and ping data services and do not set the dial-up item.
Step 18 Set Dial Up Type to Share by USB, and Network Card to Remote NDIS based Internet
Sharing Device.
----End
4 FAQs
4.1 FAQ-01
Question
What do I do if the dial-up test plan fails to be executed?
Answer
Configure the correct APN for the dial-up.
4.2 FAQ-02
Question
What do I do if the RNDIS port is still unavailable after performing steps in section
2.4.4"Performing Configurations to Make Settings Take Effect?"
Answer
This problem occurs because the manual configurations do not take effect when the terminal
is being rooted, Repeat steps in sections 2.4.3and 2.4.4until the RNDIS port is available.
4.3 FAQ-03
Question
What do I do if the Probe fails to be reconnected to the terminal after the RNDIS feature is
used and USB tethering is disabled through UI?
Answer
All ports are unavailable in the Windows device manager. As a result, the Probe connection
fails. The reason is as follows: USB tethering is forcibly enabled by setting system attributes
during the version update. Disabling USB tethering (on the UI) during the use of the RNDIS
results in the disabling of all ports. In this case, set the port mode to Google mode and restart
the mobile phone to resolve this problem. Do not use the UI to disable USB tethering during
the use of the RNDIS feature, unless otherwise specified. The purpose is to avoid unknown
errors.
4.4 FAQ-04
Question
For the terminal on which the RNDIS network adapter has been enabled, what do I do if the
terminal ports are unavailable?
Answer
Step 19 Choose Settings > Developer options, and disable Developer options.
Restarting the terminal in the manufacture mode automatically enables Developer options.
Therefore, Developer options must be manually disabled every time the terminal is restated
in the manufacture mode.
Step 20 Enable USB tethering in the manufacture mode, switch to the Google mode, and restart the
terminal.
Step 21 Ensure that the following ports are available in the Device Manager window:
[COM&LPT] DBAdapter Reserved Interface
[Modem] Android Adapter Modem
[Network] Remote NDIS based Internet Sharing Device
Repeat Step 19 to Step 20 every time the terminal is restated in the manufacture mode.
----End
4.5 FAQ-05
Question
What do I do if simultaneous network access fails when the Probe is connected to multiple
terminals?
Answer
Step 22 Check whether the local network adapter and firewall are disabled. If they are in enabled
state, disable them.
Step 23 The displayed network connection status indicates that the network cable is removed. In this
case, check whether the NDIS port and modem port are available and whether the Probe is
correctly connected to the terminal. If no exception occurs, switch the Google mode to the
manufacture mode, and switch back to the Google mode. In the problem still persists, restart
the terminal in Google mode.
Step 24 If an IP address that is the same as the obtained dynamic IP address exists on the subnet,
manually change the obtained IP address to a different one for simultaneous network access.
Command for viewing the IP address:
Enter cmd.
If the same IP address exists, change the obtained IP address to a different one on the subnet.
If the obtained dynamic IP address is different and network access still fails, check whether
Mobile data of the terminal is enabled. If it is in disabled state, enable it.
----End
4.6 FAQ-06
Question
What do I do if the error message "error: Device not found" is displayed after I run adb pull
system/build.prop d:\, but I can run adb_check.bat successfully?
Answer
Add adb pull system/build.prop d:\ to adb_check.bat.
4.7 FAQ-07
Question
What do I do if adb_check.bat fails to be executed after the terminal has been set
successfully?
Answer
Restore the factory settings for the terminal, and then perform the operations again.