Professional Documents
Culture Documents
ZTE Cell Selection and Reselection Radio PDF
ZTE Cell Selection and Reselection Radio PDF
LAI
CGI
NCC BCC
BSIC
A B C
D E F
C1 = RXLEV - RXLEV_ACCESS_MIN
- Max(MS_TXPWR_MAX_CCH - P ,0)
where,
RXLEV_ACCESS_MIN is the minimum received level the
MS is allowed to access the network
MS_TXPWR_MAX_CCH is the maximum power level of
the control channel (when MS sending on RACH);
RXLEV is average received level;
P is the maximum TX power of MS;
MAXX, YX; if X Y.
MAXX, YY; if Y X.
C2C1CROHPTTTO, when PT 31
C2C1CRO , when PT31
Area A
BTS B
BTS A
BTS C
In areas where the cells overlay with each other and differ in
capacity, traffic and functions, the telecom operator often
hopes that the MS can have priority in selecting some cells,
that is, the setting of cell priority. This function is set by way of
the parameter "Cell Bar Qualify" (CBQ).
A B
0 <-110dBm
1 -110dBm -109dBm
2 -109dBm -108dBm
61 -50dBm -49dBm
62 -49dBm -48dBm
Default: LIMIT14 LIMIT28 LIMIT315 LIMIT425
The IMSI detach process is that: the MS notifies the network that it
is moving from the working state to the non-working state, or the
process of the SIM card being taken from the MS. When receiving
the notification from the MS, the network will indicate the IMSI
subscriber to be in the non-working state, so the connection
request ending the subscriber as the called party will be rejected.
The corresponding IMSI attach process is that the MS notifies the
network that it has been in the working state , or the SIM card is re-
inserted into the MS. When the MS re-enters the working state, it
will detect whether the current LAI is the same as the LAI finally
recorded in the MS. If they are the same, the MS will start the IMSI
attach process, otherwise the MS will start the location updating
process (instead of the IMSI attach process). When receiving the
location updating or IMSI attach process, the network will indicate
the IMSI subscriber being in the working state.
ZTE University univ.zte.com.cn
univ.zte.com.cn
The information contained in the file is solely property of ZTE corporation. Any kind of disclosing without permission is prohibited.
IMSI Attach/Detach (ATT)
An ATT mark should be set as YES so that the network will no longer
process the connection process using the MS as the called after the
MS shuts down, thus saving the processing time of the network
entities and saving lots of network resources.
Please note that the ATT in different cells but in the same location
area should be set the same. Because the shutdown of the MS in
cells where the ATT is YES will start the IMSI detach process, and the
network will record the fact that the MS is in the non-working state and
reject all the connection requests when using MS as the called. When
the MS restarts and is in the same location area (so the location
update process is not started) as when it shuts down but is in a
different cell and the ATT of the cells is set as NO, so the MS will not
start the IMSI attach process, either. In this case, the MS cannot
become the called party until it starts the location updating process.
3 3
4 4
5 5
6 6
7 7
8 8
9 9
The reasons for the location update in the GSM system are
of two types: one is that the MS finds its location area
changed (with a different LAC), the other one is that the
network requires the MS to periodically update its location.
The frequency of periodic location update is controlled via
the network and the period length is determined by the
parameter T3212.
In general, in areas with larger traffic and signaling flow,
you should select the larger T3212e.g. 16 hours, 20
hours or even 25 hours, but in areas with smaller traffic
and lower signaling flow, you can set the smallerT3212 (3
hours or 6 hours, etc.). In areas where traffic is far beyond
the system capacity, we recommend that you set T3212 as
0.
ZTE University univ.zte.com.cn
univ.zte.com.cn
The information contained in the file is solely property of ZTE corporation. Any kind of disclosing without permission is prohibited.
NCCPERM