Professional Documents
Culture Documents
WCDMA Protocols1
WCDMA Protocols1
Protocols in UMTS
Presented by:
Naveen Jakhar, ITS
Topics:
Summary
2
UMTS Network Architecture
3
OSI Communication model
Application Layer
Peer to peer protocols
Application Layer WCDMA interfaces
Presentation Layer Presentation Layer
described using OSI model
Session Layer Session Layer
OSI = Open System
Interconnect
Transport Layer Transport Layer
Developed by ISO as a
Network Layer Network Layer Network Layer
general model for computer
Data Link Layer Data Link Layer Data Link Layer
communication
Physical Layer Physical Layer Physical Layer
Used as a framework for
development and
Physical Medium Physical Medium presentation of most
Node A Node B Node C
contemporary
communication standards
Each layer communicates only with two
adjacent layers and its peer on the other side
Intermediate communication nodes
Each layer receives services from the layer
below and provides services to the layer require layers 1 through 3
above Internal operation within each layer is
independent of the internal operation
Note: WCDMA covers Layers 1-3 of OSI Model in any other layer
Page 4
UMTS Protocol stack
5
NAS or the Non Access Stratum is a set of protocols in the
UMTS that is used to convey non-radio signalling between the User
Equipment (UE) and the core network.
6
UMTS CS protocols control plane
RNC terminates
the Access
Stratum (AS)
RRC, RLC and
MAC terminate at
RNC
PHY terminates at
Node B except for
outer loop power
control
RAN (access
stratum) acts as
transport for NAS
Radio Link Control (RLC): The RLC protocol offers logical link control
8
UMTS CS protocols user plane
User plane
caries user
data
Application
end to end
protocol
Access stratum
the same for
both control
plane and user
plane
9
UMTS PS protocols control plane
Control plane
for packet data
Very similar to
control plane
for PS
Identical
access stratum
10
UMTS PS protocols user plane
Additional protocol
PDCP
PDCP
compression of IP
headers
PDCP may or may
not be used
11
PDCP: RLC:
provides protocol transparency RLC protocol provides
(wrt the underlying radio- logical link control
interface protocols) for higher- over the radio
layer protocols
interface.
support for e.g., IPv4, PPP and
IPv6 (easy introduction of new MAC
higher layer protocols) MAC protocol controls
compression of control the access signaling
information (header (request and grant)
compression) procedures for the
no user data compression in Iu radio channel
mode
Figure :Generic protocol model for UTRAN interfaces
The structure consists of two horizontal layers:
1)The Radio Network Layer and
2) The Transport Network Layer.
The Radio Network Layer is concerned with application information
to be carried either user data and control information.
The Transport Network Layer is concerned with the transport
technologies used for the UTRAN interfaces.
The two layers are logically independent of each other. This makes it
possible to change the Transport Network Layer without affecting
Radio Network Layer, if required. In Release 99, the Transport
Network Layer is based on ATM. In Release 5, IP is used.
14
The user plane includes the user data between the UE and the
network and the data bearers. The user data consists of data streams
characterized by frame protocols specific to a UTRAN interface.
The control plane includes the application protocols and the signaling
bearers, which transport the control information.
The transport network control plane includes the access link control
application protocol (ALCAP). ALCAP is used to set up transport
bearers to carry user and control plane information. It is not visible to the
Radio Network Layer.
15
Figure : Iu-CS interface protocol structure.
16
IUcs interface protocol structure
In UMTS, the interface between RAN and CN is Iu.
Iu-CS is the interface specified between the RAN and the 3G MSC.
The Iu-PS interface is defined between the RAN and the 3G SGSN.
In order to have uniformity, 3GPP specifies a single protocol at Radio Network
Layer for the Iu-CS and the Iu-PS interfaces.
The radio access network application protocol (RANAP) is the Radio Network
Layer protocol for the Iu interface. The RANAP peer entities reside in 3G
MSC/SGSN and the SRNC. The RANAP functions are specified in 3GPP TS
25.413 in detail. In summary, RANAP procedures support the following key
functions:
Radio access bearer (RAB) management including RAB setup, modification,
and release
Iu connection management
Facilitate general UTRAN procedures from the core network, e.g., paging
requests from the CN to UE
Services to upper layers including the transportation of upper layer
nonstratum protocols (i.e., call control, session management, and mobility
management) messages between the UE and CN
Overload and error handling
SRNS relocation
UE location reporting 17
The Service Connection and Control Part (SCCP) offers both connectionless and
connection-oriented services. Each active UE is assigned a separate logical link in case of
connection-oriented service between two RANAP entities.
The SCCP utilizes services provided by the lower layers to transport messages between two
entities.
Layer 3 Broadband Message Transfer Part (MTP3b) provides message routing,
discrimination, and distribution. It also provides link management functions including load
sharing between linksets.
The SSCF-NNI(Service-Specific Coordination Function for Signaling at the Network Node
Interface) maps the requirements of above layers to the requirements of SSCOP.
The SSCOP (Service-Specific Connection-Oriented Protocol)provides the mechanism for
the establishment and release of connections and the reliable exchange of signalling
information between the signalling entities.
In cases where the IP transport option is chosen, the services are provided by M3UA(MTP 3
User Adaptation Layer), SCTP (Stream Control Transmission Protocol) and IP.
AAL5 (ATM Adaptation Layer 5)is used to adapt the upper layer protocol to the
requirements of the lower ATM cells.
18
As described in the previous section, the purpose of the transport network
control plane is to set up, maintain, and release bearers to transport the data
via the user plane.
In the user plane, ATM Adaptation Layer 2 (AAL2) is used as the user data
bearer. AAL2 has been specifically designed to transport short-length packets.
19
Figure: Iu-PS interface protocol structure. 20
IUps interface protocol structure
The Iu-PS interface is specified between the RAN and the 3G SGSN.
Like GPRS, GTP-U uses UDP/IP. AAL5 is used to carry the packet-
switched user traffic over the Iu-PS interface.
21
Figure :Iur interface protocol structure. 22
Iur interface protocol structure
Iur is the interface between the RNCs.
One of the RNCs assumes the controlling role and is termed the serving
RNC (SRNC); the other RNC is termed the drifting RNC (DRNC).
Paging
Relocation execution
23
RNSAP uses the services of the Transport Layer for reliable
transfer of signaling messages in both connectionless and
connection-oriented modes.
24
25
Iub interface protocol structure
Iub is the interface between the Node B and the RNC .
Configuration verification/alignment
27
Thank You!
28