Professional Documents
Culture Documents
Manual Installation LDM Lamp Driver Installation Sheet Rev A
Manual Installation LDM Lamp Driver Installation Sheet Rev A
Manual Installation LDM Lamp Driver Installation Sheet Rev A
1 Product Overview
The LDM Lamp Driver Modules (LDM-32, LDM-E32, and LDM-R32) are used to drive lamps or LEDs in a
custom mimic connected to an addressable fire panel.
2 Installation
WARNING: Remove all power sources to the panel before installation. Leave the
external and main power OFF until installation is complete.
Page 1 of 4
Relay Power Ribbon Cable connection
LDM-32
(or LDM-E32) J5 J6 J7 J8
J11
LDM-R32 J10
J5 J6 J7 J8 9.;>
J10>=D2? J9
K1 K32
Standoff Standoff
K2 K31
TB4
TB1 K3 K30
1 1
2 2
3
K4 K29 3
4 4
5 K5 K28 5 J2
6 6
Chassis LDM-32 LDM-R32 7 K6 K27 7
(or LDM-E32) 8 8
Figure 2-2 – Mounting a LDM-R32 on top of Figure 2-3 - Connecting the Relay Power
a LDM Module Ribbon Cable
2.3 Connections
NOTE: When cables are not run in a conduit, shielding on cables for EIA-485
connections must be grounded outside the enclosure and fire panel. See the LDM
Series Instruction Manual for more information.
IN
OUT 120 CPU Board
OUT EOL
NC Supervision 7 Last IN
Inputs 6 LDM-32
IN 5
OUT 4
IN 3
OUT 2 IN
EGnd 1 OUT
OUT
NC Supervision 7 IN
Inputs 6
IN 5
OUT 4
IN 3 IN
OUT 2 OUT
EGnd 1
OUT
First IN
LDM-32
NC Supervision 7
Inputs 6
IN 5
OUT 4
IN 3
OUT 2
EGnd 1
Figure 2-4 – Power (TB1) and ACS Comms (TB2) connections to the CPU
Figure 2-5 - Connecting LDM-E32 expander modules with the ribbon cable
Page 2 of 4
Point Status LEDs: Point Status LEDs:
Use RED for Alarm points Use RED for Alarm points System
YELLOW for Trouble points, and System YELLOW for Trouble points, and
GREEN for Output points.
Trouble LED
GREEN for Output points. Trouble LED (Yellow)
(Yellow)
Custom Custom
J5 J6
Graphic Graphic
J7
J11 J8 Display Display
+5
J4 Common
J10
LAMP J9
SWITCH POWER
Figure 2-6 - Lamp/LED Wiring for 5 V DC Figure 2-7 - Lamp/LED Wiring for 24 V DC
NOTE: All LEDs must be in the same room as the LDM modules.
3 Configuration
3.1 Setting the Address and Operating Modes
SW4
5
6
Switch set to
7
OFF position
8
LDM-32
NOTE: The available address range for the LDM-32 is 2-32 (inclusive.)
1. Set a unique address for the LDM-32 using the rotary address switches along the side of the
module.
2. Set the operating mode using the DIP switches on the LDM-32. See Table 1 for a description of the
switch functions.
3. Configure annunciator points via the panel’s keypad or through VeriFire Tools. Refer to the panel’s
Programming Manual for further information on programming the annunciator.
Page 3 of 4
Switch Switch Default
Description
Bank No. Setting
1 OFF Turn ‘ON’ when the lamp driver is used to control relays.
2 OFF Configures the number of expander modules.
See Table for details.
3 OFF
4 OFF Not used.
Turn ‘ON’ for Receive Only mode, to mirror another LDM at the
5 OFF
SW3 same address in a different location.
Turn ‘ON’ for Piezo Disable, to disable the buzzer from sounding
6 OFF
for any event.
Turn ‘ON’ for Switch Inhibit, to disable point control switches on
7 OFF
the annunciator.
Turn ‘ON’ for Flash Inhibit, to disable the flashing of LEDs for
8 OFF unacknowledged events. Also disables piezo.
N.B.: Flash Inhibit must be ON when using the LDM-R32.
Table 1 – DIP Switches and Default Settings
O 2 3
F O 1 2
1 F F
F
O 2 3
F ON OFF
2 F
Position Position
O 2 3
F
3 F
4 Supplemental Documentation
Page 4 of 4