Professional Documents
Culture Documents
NTN OWC Catalog
NTN OWC Catalog
One-way Clutches
Tension Pulleys,
Bottom Roller Bearings
*ワンウェイほか/B294-B308_*ワンウェイほか/B294-B308 11/05/25 13:48 ページ 296
One-way Clutches
Type HFL
One-way clutch HFL has an outer ring drawn from thin
HFL 10 22
steel plate by precision drawing, a clutching function, and
Width an integral needle roller and cage assembly capable of
φ8―φ35 supporting radial load at its both ends respectively.
Bore diameter
Thus, this HFL can function as clutch and, in addition,
Type code
support radial load.
Both of Type HF and HFL use a polyamide resin cage Table 2 Recommended housing wall thickness (recommended)
and press the needle rollers to a wedge, which is formed Housing material Housing wall thickness
between the outer ring cam face and the shaft, by action Iron-based 0.75 (D−Fw) and over
of a plate spring supported with the cage.
Light metal alloy 1.5 (D−Fw) and over
For values of D and Fw, refer to the relevant dimension table.
Clutch fit
Table 1 shows the one-way clutch fits on shaft and in
housing. Both of Type HF and HFL are only press-fitted in a Shaft and housing requirements
housing, needing no axial fixing by use of a snap ring, etc.
However, due to the outer ring drawn from thin steel by Table 3 shows the shaft and housing requirements.
precision drawing, the performance of the both is directly
affected by the dimensional and profile deviations of the Table 3 Shaft and housing requirements (recommended)
shaft/housing. To avoid such an inverse affect, shaft and
Shaft Housing
housing accuracy must be controlled with good care. Any Characteristics
housing is required to have the wall thickness of a Type HF Type HFL Type HF Type HFL
specified value or more. Table 2 shows the Roundness (max) IT3 (IT4) IT4 (IT5)
recommended value. Cylindricality (max) IT3 (IT4) IT4 (IT5)
Surface roughness 0.2a 1.6a
Table 1 Clutch fits (recommended)
Housing Surface hardness HRC58―64 −
Type Shaft
Iron series Light metal alloy Effective hardened
layer depth (min) 0.4mm −
HF
h5 (h6) N6 (N7) R6 (R7)
HFL
B-296
*ワンウェイほか/B294-B308_*ワンウェイほか/B294-B308 11/05/25 13:48 ページ 297
Lubrication
Oil lubrication is optimum for these one-way clutches, A
but generally grease lubrication is mostly applied to this
type of one-way clutch. NTN one-way clutches are filled
up with a suitable grease. These clutches need no further 15˚
grease replenishment, but subject to general applications.
In replenishing, good care must be exercised of too
much grease filling. Too much filling could cause B
interference with smooth clutching. A=D−(0.2∼0.3)mm
For selection of an appropriate lubricant, contact NTN B=Fw−(0∼0.025)mm
D=Outer diameter of one-way clutch mm
Engineering for technical assistance. Fw=Roller inscribed circle diameter mm
(Refer to applicable Dimensions Table.)
Delay angle[deg]
○
2 HF2016 28.5N・m ○
2 HF2016 28.5N・m
oneway clutch can vary 3˚
○
3 HF3020 90N・m cycles exceeds 106, 3˚
○
3 HF3020 90N・m
depending on the oneway ○
1
change in the delay angle ○
1
clutch designation and the on NTNoneway clutches is
2˚ 2˚
magnitude of torque the small (data obtained from
○
2
○
2
oneway clutch carries. The the NTN analyzer).
chart in the right graphically 1˚ 1˚
illustrates the trend in relation ○
3
between load torque and ○
3
B-297
*ワンウェイほか/B294-B308_*ワンウェイほか/B294-B308 11/05/25 13:48 ページ 298
Type HF
Type HF
FW 6〜35mm
Boundary dimensions Torque capacity Bearing Mass Part number by radial load
Md numbers
mm N・m kgf・m kg (approx.)
Fw D C needle roller oil retaining
0 (approx.) bearing bearing
−0.25
B-298
*ワンウェイほか/B294-B308_*ワンウェイほか/B294-B308 11/05/25 13:48 ページ 299
Type HFL
C
φD φFW
Type HFL
d 8〜35mm
Shaft dia. Boundary dimensions Basic load ratings Bearing Torque capacity Mass
dynamic static dynamic static numbers
mm mm N kgf N・mm kgf・m kg
d Fw D C
0
−0.25 Cr Cor Cr Cor (approx.)
B-299