Professional Documents
Culture Documents
Star1 User Manual
Star1 User Manual
: 10.10.2004
FEATURES : 1/83
STAR1
TELEPHONE EXCHANGE
INSTALLATION &
USER MANUEL
MULTİTEK STAR1 INSTALLATION AND SYSTEM
: 10.10.2004
FEATURES : 2/83
STAR1
TELEPHONE EXCHANGE
INSTALLATION & USER MANUAL
Thank you for selecting the STAR1 telephone exchange. This manual
teaches the features of your exchange. So you may get the best
performance from your exchange for years without having any trouble.
Please note that the product ,their specification and the information appearing in this
document are subject to change by Multitek without notice.
DOC.STAR1-02-050505
MULTİTEK STAR1 INSTALLATION AND SYSTEM
: 10.10.2004
FEATURES : 3/83
INDEX
INSIDE OF THE STAR1 EXCHANGE BOX 8
Exchange Installation & System Features 9
Selection Of The Place To Install The Exchange 9
Grounding The Exchange 9
Definition Of A Good Ground 9
Installation Of The Exchange 9
Installing The Exchange 9
Installation Of The Exchange Cables 10
Connecting KTS300 Operator Console Set 10
Connecting The subscribers 10
Connecting 220V Power Line 10
Connecting Batteries If Exists 10
Giving Energy 10
STAR1 EXCHANGE CABLING AND BOARD PLACEMENT 11
STAR1 Exchange Board Types 11
1.RECTIFIER BOARD (mpu0158) 12
2.Main Board(mpu0161) 14
3.16 Subscriber Board(mpu0159) 15
4. External Board(mpu0160) 16
5.Call Attendant Board(mpu0162) 16
6.Battery Module (mpu0170) 17
The place chosen for the installation mush have the following conditions :
- The exchange must be installed to a place with no humidity, with no water leakage.
- The place must not be dirty, smoky.
- The place must not be near of the voltage generator, uninterrupted power supplies, high
voltage power lines.
- The exchange must not be installed above the radiator, or to the place where sun shines
directly.
- The exchange must be installed preferably 1.5 m above the ground with empty surrounding
to work easily.
- The installed place must be sufficiently lightened.
- The exchange must be installed in a place where not many people may reach to.
It is not necessary to have a good ground for the operation of STAR1 exchange. However to
protect the exchange against high voltages a good ground is a must.
The exchange plug is provided with ground connection. If the exchange is installed in a place
where there is no ground connection at all the exchange ground must be connected to a
radiator or to a water pipe with a thick cable. This is better than nothing for protection of the
system against high voltages.
Attention: If you connect the exchange ground to the phase of the mains power by
mistake you destroy the high voltage varistors of the exchange and give some harm to
your exchange and the Telecom lines .
paper guide provided .Insert the fixings and screws and hang the exchange on the
wall. It is advisable to install the exchange about 1.5 meter above the ground.
Installation of the exchange cables :
Place a MDF box about 1 m near the exchange. Connect the cable between the exchange
and MDF in proper order. Similarly connect the telephone internal and external lines to the
other side of the MDF in order.
A five meter long ,two sides plugged cable is given with the KTS300 special key telephone
set (operator console set).One side of the cable is inserted to the socket on the exchange
and the other side to the telephone set.
Giving energy :
After you connect the power line of the exchange to the mains socket , press the power
switch located inside the cabinet . The exchange gets the power. 220v LED on the exchange
rectifier board becomes on and if the exchange properly working Active LED on the main
board stars blinking.
MULTİTEK STAR1 INSTALLATION AND SYSTEM
: 10.10.2004
FEATURES : 11/83
EXT BOARD
VOICE ATTENDANT EXT 7-12
MAIN BOARD
The basic exchange has a main board and a rectifier board with a 220 VAC transformer. The
basic capacity of the exchange is 6 external and 16 internal terminals. The capacity of the
exchange may be increased by adding the subscriber or the external boards on top of each
other. The call attendant board is similarly inserted on to top of the other boards.
MULTİTEK STAR1 INSTALLATION AND SYSTEM
: 10.10.2004
FEATURES : 12/83
1.RECTIFIER BOARD(mpu0158)
220VAC transformer and the rectifier board generates the necessary voltages to the system.
It is connected to the main board of the exchange by a socket. The output voltages of the
rectifier board are;
75VAC (ring)
-24 VDC (line feeding)
+ 5 VDC
+ 5 VDC
+ 10 VDC (for consoles)
The STAR1 RECTIFIER BOARD shows the main diagram of the rectifier board.
RING BRIDGE
It connects the ring voltage to the system. If a battery module is connected the bridge
position must be changed.
COOLERS
They are the coolers of the voltage circuits.
220V LED
It shows the main power exists.
-24V LED
It shows -24V available
+5V LED
It shows +5V available
+5V LED
It SHOWS +5v available
+10V LED
It shows +10V available
-24V Fuse
It protects -24V output. When the fuse is blown –24V LED becomes off
+5V Fuse
MULTİTEK STAR1 INSTALLATION AND SYSTEM
: 10.10.2004
FEATURES : 13/83
It protects +5V output. When the fuse is blown +5V LED becomes off
+5V Fuse
It protects +5V output. When the fuse is blown +5V LED becomes off
+10V Fuse
It protects +10V output. When the fuse is blown +10V LED becomes off
RECTIFIER BOARD OUTPUT SOCKET
It is the connection point to the main board of the system.
220 VAC FEEDING TRANSFORMER
It supplies the voltages to the rectifier board. The output voltages are 75 VAC,30 VAC and 10
VAC. The primary input of the transformer has a 1A/250V fuse for protection.
220V TRANSFORMER
SOCKET
COOLERS
RING BRIDGE
STAR1
RECTIFIER BOARD
+10V FUSE
-24V FUSE
+5V FUSE
+5V FUSE
SPECIAL POWER
TERMINALS
+ ø
-
BATTERY MODULE SOCKET ø
VOLTAGE LEDS 8 7 6 5 4 3 2 1
The main board of the system has all the necessary circuitry for microcontroler , RAM,FLASH
and the other circuits. The main board has also 16 internal subscriber and 6 external line
circuits. The figure shows the connection points of the main board.
ENERGYİ
SOCKETİ
BAT
SUBSCRIBER OR EXTERNAL
SUBSCRIBER OR EXTERNAL
EXTENSION SOCKETS
EXTENSION SOCKETS
Battery Bridge
STAR1
MAINBOARD
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
T6
TT
T4
T1
T2
T5
CONSOLE a b a b a b CONSOLE
SUBSCRIBER
STAR1 SUBSCRIBER
SUB SUB SUB SUB
10 12 14 16
SUBSCRIBER TERMINALS
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
The external board provides additional 6 external to the exchange. It has the 6 external line
circuits and their connection terminals. The board is manufactured as 3 or 6 external.
MULTİTEK STAR1 INSTALLATION AND SYSTEM
: 10.10.2004
FEATURES : 17/83
EXTENSION SOCKETS
STAR1 EXTERNAL
BOARD
EXTERNAL CONNECTION
TERMINALS
T T T T
T T
7 8 11 12
9 10
It answers the incoming calls coming to exchange by a greeting and allows to call the internal
lines. Therefore, it reduces the burden of the operators. The call attendant board is produced
as 4 or 8 call attendant channels.
MULTİTEK STAR1 INSTALLATION AND SYSTEM
: 10.10.2004
FEATURES : 18/83
1 2 3 4 5
6 7 8
VOICE ATTENDANT
BOARD SOCKETS
If the main power of the exchange (220VAC) is often broken down it is necessary to add the
Battery Module to the exchange to back up the system power. The battery module works with
two pieces of 12V maintenance free battery up to 12 Amper hours capacity. When the mains
power is off the battery module supplies the exchange energy and when the power is on the
battery module charges the batteries.
MT26,STAR2 and STAR1 use the some battery module circuit.2x12V battery is connected to
module with a pair of cable with minimum 2x0.75 mm2 thickness.
The module connection to the exchange is done by a cable with two sides plugged.
-It is recommended not to connect more than 12 Amper hour capacity batteries to the
system. The exchange may have trouble to charge the batteries.
-If the battery cables are connected wrong side the 3A fuse on the board is blown out.
-When the battery voltage becomes less than 18V the module separates the battery from the
exchange. So it prevents to dry out the batteries.
-Note that connection of any type of battery other than the maintenance free battery may
cause problem to the system.
MULTİTEK STAR1 INSTALLATION AND SYSTEM
: 10.10.2004
FEATURES : 19/83
12V RING
+ - LED LED
The batteries are connected to the battery + - terminals on the battery module of the
exchange. The board has a 3A battery fuse. If the batteries are wrong connected the fuse is
blown - out.
The batteries feeds the exchange until the voltage drops to 18V. When the battery voltage
becomes less than 18 volts the battery is disconnected from the exchange automatically.
When the power comes back the batteries are charged by the system.
When the battery module is connected to the system RING BRIDGE position on the main
board should be changed otherwise the telephones do not ring.
(Please see the exchange –PC connection section for more details about the ET2000
PC call logging program )
Note : Exchange side DTR (Data Terminal Ready ) on the main board is connected to the
printer connector pin 20. This pin is used detect if the printer is connected and operating. If
the printer is not connected or its power is off the call logging data are stored in the
exchange memory and when the printer starts operating all stored data are transferred. If
DTR terminal is used it is necessary to enter the program 7447 964 .(To cancel enter 7447
965 )
The printer prints out external calls indicating calling, transferred internal lines, called number
date, start time and duration of the call pulse count and cost.
Example:
Each external line in the exchange has an optional charge detector of 12/16 KHZ.
If the charge pulses are received and if the unit fee of the charge pulse is entered the printer
prints out the pulse - count and cost of the call. If the charging signal is not received the
printer prints out all calls longer than 20 sec.
The exchange stores the charging data of last 70 calls. If it is required it is possible to print
the last 99 stored data to the printer by a program ( program 892 ).
MULTİTEK STAR1 INSTALLATION AND SYSTEM
: 10.10.2004
FEATURES : 22/83
The printer program has various programs for printing the call data . ( Look the printer
programs ).
MUSIC ON HOLD
When the external lines are on - hold the exchange gives music to the waiting side. STAR1
exchange has two types of music.
Note: The external music is connected to the exchange at TEYP a and b terminals.
The subscribers on the exchange are numbered as 0, 101, 102 to 179 for STAR1.
- All subscriber are restricted to make out going call ( other than the subscribers allowed by
the program ).
- Incoming calls may ring up to four subscribers at the same time (subscribers defined by the
program 97. Default number 0 ).
Subscribers who do not have night service restriction will have the same authorization as
day. If he is fully restricted for day he will have the city call authorization for night. The
subscriber allowed to have night calls are programmed by the program 83 aaa 0.
WARNING : If you connect DP telephones or telephones with long duration flash button it
is advisable to set the flash time 600 ms. Otherwise all conversations will be cut off during the
transfer.
* button:
A) Pressing * makes on hold the conversation as hook - flash. ( It may be used as hook -
flash function ).
B) Pressing * seizes the 1.th external line after the dial tone.
# button:
A) Pressing # functions as hook - on and then hook off the telephone ( to receive the dial
tone without playing the hook of the phone ).
B) Pressing # after the dial tone seizes 2.th external line.
C) # is also used to send hook-flash to the external line where an upper exchange terminal is
needed to be on hold and transfer.
MULTİTEK STAR1 INSTALLATION AND SYSTEM
: 10.10.2004
FEATURES : 24/83
Attention : It is needed to press longer than ordinary buttons for the * and # buttons.
Note : * is used for the function of the flash operation for the remote programming.
RINGING CURRENTS
STAR1 has there types of ringing current duration;
External call : The telephone rings slowly to indicate an external call. (2 sec on 4 sec off)
Note: It is possible to use access code 9 instead of any group code if the subscriber is
allowed to access only one group. But if a subscriber is allowed to access more than one
group he must dial the group access code.
MULTİTEK STAR1 INSTALLATION AND SYSTEM
: 10.10.2004
FEATURES : 26/83
For call forward if absent feature use 742 code. The telephone rings for 4 seconds if
not answered routed to the forwarded subscriber.(e.g. 742 15 directs the calls to the
number 15 if it is not answered in 4 seconds.)
For cancelling call forward if absent feature use only 742 code.
CONFERENCE
When you are making an external line conversation, if another call comes to your phone you
hear bip sounds on your earphone. To answer the second call you have to park the current
line and seize the other.(See the answering second call sections.)
CONSULTATION HOLD
When you are talking to an internal or external subscriber if you need to talk to another
internal subscriber;
- If the called number does not answer or if you want return back to the pervious call you
press * ( or hook - flash ).
- If the called number is busy ,if you hook - on your phone the call is parked on the busy
subscriber .The busy subscriber hears bip tone on his ear. When the phone become free it is
ringed.
- If the transferred external call is not answered in 1 minute the call is routed to the operator.
- If you make any mistake during the transfer operation or you hook - on, the call returns back
to you.
The external line becomes parked for the duration of 1 minutes. If it is not seized back in one
minute, it returns back to you automatically. You may park as many external as you need.
If you need to seize back a specific parked external line dial the external selection number
( e.g. 531 for the first external ).
If the parked external line is not seized back in one minute, it returns back to the subscriber.
- Hook - on.
The subscriber that the call is parked on hears the bip tone. When he hooks on the telephone
rings and talks. If the call parked is not serviced in one minute it is routed to the operator.
CALL PICKUP
To answer a call ringing a telephone,
- Receive the dial tone.
- Dial 72, and than the ringing subscriber number. if you are in a call group
( PBX ) to answer any ringing subscriber in the group you just dial 80.
For example, if 11 is ringing dial 72 11 to seize the call.
INTRUSION
If the called line is busy and if you want to make intrusion;
- After hearing the busy tone, dial 49. If your level of intrusion is higher than the called line
level you entered to the conversation of the called subscriber. The sides hear bip tones
(optional) . If your intrusion level is lower than the busy subscriber you hear congestion tone.
-You become out of conversation when you hook - on. The exchange allows three levels of
intrusion;
Fully restricted, half restricted, unrestricted. Same level authorized subscribers may not
intrude their conversations.
MULTİTEK STAR1 INSTALLATION AND SYSTEM
: 10.10.2004
FEATURES : 30/83
AUTOMATIC CALLING
- All subscribers of the exchange have the feature of the automatic calling. Automatic calling
is an useful feature when the called external number is busy or if you want the exchange to
call an external number automatically.
- If there are more than one automatic call request at a time the exchange puts them in
queue and serves in order.
- The exchange calls the numbers in maximum 15 times. When the called side rings it makes
the connection. If the called terminal is not reached in 15 times the request cancelled.
- When the call is established but the originating terminal is busy you hear a bip tone in your
earphone. You have to hook - on the phone immediately and answer the call.
- When you hear busy or congestion tone during an external call ,the first dial * (or hook -
flash) and then 77.
- Hear the acceptance tone (ring back) and hook on the phone.
- The exchange finds the external number for you and makes the connection.
- When you receive the busy tone, dial 48 and hear the acceptance tone.
MULTİTEK STAR1 INSTALLATION AND SYSTEM
: 10.10.2004
FEATURES : 31/83
- Hook - on.
- When the subscriber queued hooks on his telephone your phone starts ringing. When you
hook-off the other side stars ringing and you talk.
- Or when the external line / lines queued becomes free your phone starts ringing and when
you hook on the external line is connected to you. You hear Telecom dial tone.
- After hold on the external line, dial 741 than the internal line number ad hook - on.
- When the subscriber that the call is transferred hooks - on the external line comes back to
you by ringing your phone.
- You may make as many serial call transfer as you wish.
- When someone dials the external access code the exchange gives a bip tone, requiring the
password. When the three digit correct password is entered the external line is seized and
Telecom dial tone is heard.
DON’T DISTURB
If you do not want to be disturbed by your ringing telephone;
When someone calls you your telephone rings once and stops. You may answer the phone
any time as long as the calling party keeps ringing.
DOOR OPENER
If you want to open the door by your phone, dial 71 and hook – on the telephone. A special
relay in the exchange operates for 1 second ( or 2 sec by programming ).
(Be sure to connect your door opener to OZR a - b terminals of the exchange).
It is possible to restrict some subscribers to open the door.
(By program 82aa4 / 5).
When the subscriber hooks – off his telephone the exchange starts dial automatically the
external number defined in the exchange speed dial memory 99.
For this feature the subscriber must be defined as hot line (see the programming code
80 aa 7) and the external number must be entered into the common memory 99.
7600 RINGING
7001 MEETING
7602 AT HOME
7603 ABSENT
7604 CALL LATER
7605 ON ATRIP
7606 AT LUNCH
7607 VACATION
e.g. : If you are in a meeting, dial 7601 and hook - on your phone. When a terminal with
KTS300 telephone calls you they see " MEETING " message on their LCD display.
For cancelling the messages enter 7600 and hook - on.
MULTİTEK STAR1 INSTALLATION AND SYSTEM
: 10.10.2004
FEATURES : 34/83
AUTHORISATION TRANSFER
(Making calls from a telephone as your telephone authorization)
It is possible to use any internal telephone of the exchange as your telephone with the same
authorization. For example, if the telephone where you are has no access to the external
lines you may change its authorization to your telephone level. When the telephone is
hooked-off the authorization level of the telephone returns to the old values.
- Only subscribers allowed may make external outgoing calls. They will have the same class
of service as day. If they are restricted for day they are allowed to make only city calls in the
night service.
- Incoming calls ring the subscribers defined by the program. Maximum four internal terminals
may be ringed at the same time. One answers the call when he hooks off.
The night service is cancelled by entering 7448 from the operator telephone.
PBX FEATURE
When your telephone is busy or you are absent if you want to re-route the call to another
subscriber you have to use PBX feature of the exchange. PBX feature is activated by the
programming codes 860 or 862. It is possible to make a PBX group for the internal or
external calls by the program 860 or a PBX group for only external calls by the program 862.
Maximum 10 subscribers may be in a PBX group and it is allowed to make 9 different PBX
groups.
MULTİTEK STAR1 INSTALLATION AND SYSTEM
: 10.10.2004
FEATURES : 37/83
- By program code 94 assign one (or more) external to make a group of externals.
- By program code 85 define the subscriber which group he uses.
- By program code 92 redirect the incoming calls coming from the external to his phone.
The exchange allows the calls coming from an external line to be routed to any internal line. It
is possible to route each external coming call one by one to the different subscribers.
Program code 92 is used for routing the external calls to the subscribers. Initially all calls are
directed to the operator number 0.
It is possible to program the hook - flash duration of the each terminal one by one by program
code 83. The hook - flash time may be programmed as 80,150,250, 600,800
MULTİTEK STAR1 INSTALLATION AND SYSTEM
: 10.10.2004
FEATURES : 40/83
or 1000 milisecond .
WARNING : 80 msecond hook - flash time is the default value of the exchange. If the
exchange has the DP telephone sets or the telephones with flash button, it is advisable to
make 600 ms hook - flash time for those telephones.
*,#,A,B,C,D buttons for the exchange features. ( see programming code 83aaa2/3 ). Initially
all internal numbers are allowed to use *, # , A,B,C,D buttons.
75 ss kkkk* where ;
ss : memory of code number 01-20
kkkk : maximum 4 digits restriction code.
* ( or hook - flash ) : if the code less than 4 digits it is the terminator.
Note that the programming code 7447 is not needed for entering the codes .
( If 75 ss* is entered the previously entered code is erased ).
B) By programming code 85 define the restriction code group to the subscribers. See the
programming section for the code restriction table.
MULTİTEK STAR1 INSTALLATION AND SYSTEM
: 10.10.2004
FEATURES : 42/83
Example : Let us assume the internal number 150 will be restricted to call the numbers
started with 251,262 and the number 180 is restricted to the numbers starting with the codes
271 and 281.
It is possible to connect as many as required door phone device to the system. The door
phones are called for talking with their terminal numbers. The door phones are the special
design devices as the followings;
Any internal terminal (s) is defined as door phone terminal by program 82 aa 6/7.
It is also possible to define the internal number that will ring when the call button on the door
phone is pressed by the program 82 aaa 8.
The ring durations of the internal and external rings may be changed vice versa. The
program 953 is used for that purpose.
As a default * button may be used to hold on the conversation and # button is used to refresh
the dial tone. Program 966 and 967 changes the functions of * and # vice versa.
If the subscriber has the hand free telephone and if a radio/CD player is connected to the
exchange for the hold on music it is possible to program the subscriber to listen music when
he is free. For that feature;
-Subscriber hooks of the telephone and receives the dial tone. If he does not
dial any number in 6 seconds the subscriber is connected to the music source
of the exchange.
-To call a number he must hook off the telephone.
-When there is a call to him the music stops and he hears the ringing
tone. When he hooks on and off the telephone he answers the call.
Programming code 81 aa 5/6 makes the music subscriber.
It is possible to program the exchange so that an external calls may ring up to 4 subscribers
at the same time. The ringing subscribers is defined by the program 97 as the night service
subscribers. The program for ringing the subscribers for an external call is 851078/851079.
As a default an external call may ring the operator.
The exchange may test the externals automatically to detect if some of them are broken. The
test may be performed when it is required or periodically at hours 07 00 and 19 00. See the
programs 851082 , 851083 and 851084.
FICTIVE CHARGING
If the externals of the exchange do not have the 12/16 KHz charging signal the exchange
may perform fictive charging for each call. (It is also possible to make fictive charging for
some externals while the others use 12/16 KHz charging pulse.)
-Program 93h 4/5 programs externals for fictive charging.
-Program 88 3-5 xxx enters the charging duration for local, area and International
calls.
MULTİTEK STAR1 INSTALLATION AND SYSTEM
: 10.10.2004
FEATURES : 45/83
2. LCR Programs:
The following programs is used for the LCR :
7447 9503 LCR feature is used in the exchange.
7447 9502 LCR feature not used (DEFAULT)
9513 50 Free
Note: The table shows the default values.
The route number and the dialled prefix may be re-programmed.
An example application for the default routes:
Let us assume only numbers starting with 053 may be called through the external 4 and all
other numbers are called through the external 1,2,3. The following program is entered for
each external line to define the routes allowed to them.
The Exchange LCR Table shows the default LCR table and the numbers. This table may be
re-arranged according to the needs. To program it ,enter the exchange programming code
7447,then 9513 and then the corresponding LCR memory number , route number and the
digits that will be analysed (up to 4) and end it with * (star) key.
Example: If numbers starting with 056 is needed to direct a new route 9, enter
When you create a new LCR table please be careful about the followings;
One may require to see the existing LCR table defined in the exchange.
Enter the following program:
7447 9514
to damp the LCR table to the printer or PC. The default table format is shown below;
- - -
- - -
- - -
50 - -
The program for entering the PIN code (from the number 0 operator telephone):
Entering PIN number is the same as entering speed call numbers to the special memory of
the operator telephone.
- Hook-off the telephone
- Dial 78 and then the memory number corresponding to the required route.
e.g. If you select route 6 dial 7805.
- Then dial 1
- Enter PIN number
- Enter * or flash. You hear the dial tone.
Example: If the PIN number is 222 333 4444 and the route is 5 , enter 7804 1 222 333 4444*
5.1.2 Entering the Long Distance Operator Access Number to the Exchange:
The access number is the long distance operator call number and it is usually in the from of
08xx xxx xxxx.
The access numbers are entered to the common memory 11-18 of the exchange.
- Hook-off the telephone
- 78 and the corresponding common memory number is dialled.
Example: If the long distance operator route is 5 selected enter 7814
MULTİTEK STAR1 INSTALLATION AND SYSTEM
: 10.10.2004
FEATURES : 50/83
- Dial 1 ,
- Then the access number ,
- Enter * to terminate the program.
Example: If the access number is 0811 222 3333 and the route is 5 enter 78 14 1 0811 222
3333 *.
Entering the PIN and the operator access number to the exchange is not enough for using
them.
They should also be activated to use.
The access code for this route becomes active .So whenever a number belonged to that
route is dialled the exchange first dials the access number automatically.
Example: If you want to activate the access number for the route 5, enter 7447 9511 51 .
Example: If you want to activate the PIN number for the route 5 enter 7447 95 12 51.
Whenever a number starting with 00 is dialled the exchange first dialles the access code then
PIN number automatically and then the dialled number.
The following program is entered by the operator telephone:
(note that default table parameters are used. )
- LCR feature is activated :
7447 9503
- Program the external lines that use that route.
For example, the 1.and 2 external lines will be used for local, area and the international calls
through the long distance operator.(The other externals are out of service)
When the number starting with 00 (international call) is dialled the exchange first dials the
access number of the operator and then the PIN number and then the dialled number. The
user ,off course ,will not be aware of those actions. He only keeps dialling his number.
VOICE ATTENDANT
( ROBOT OPERATOR ) FEATURES
STAR1 exchange has a voice attendant (robot operator) board. Voice attendant module
answers the incoming calls, reads the recorded message and gives appropriate voice
messages to the calling side about the internal number that the calling party wishes to talk.
When the voice attendant answers the calling party may dial the internal number directly,
without the help of operator.
NECESSARY EQUIPMENT
The exchange has a voice attendant board which may be placed in the sockets at the top of
the boards. The voice attendant board may be four or eight channels. The four channel voice
attendant is ready to use as default .If eight channel board is used the channels must be
given to the service by the program 85 100 6x where x is the channel number.
After programming 7447 918 the following messages are read to the voice attendant:
Programming Message # Advisable message Max Message
Code structure duration Listening Code
7447 85100 01 1. message Good day. Please dial 25 sec. 7447 85 100 41
the internal number.
7447 85100 02 2. message You are connected to the 6 sec. 7447 85 100 42
operator.
7447 85100 03 3. message The number you dialled 3 sec. 7447 85 100 43
is busy.
7447 85100 04 4. message The number you dialled 6 sec. 7447 85 100 44
does not answer.
7447 85100 05 5. message You are connected to the 3 sec. 7447 85 100 45
number you dialled
7447 85100 06 6. message The number you dialled 3 sec. 7447 85 100 46
is wrong.
7447 85100 07 7. message We are closed. Please 6 sec. 7447 85 100 47
call in working hours.
MULTİTEK STAR1 INSTALLATION AND SYSTEM
: 10.10.2004
FEATURES : 54/83
Example:
- After entering 7447 85 100 01 you get the dial tone for 4 seconds.
- When the tone is interrupted you read the message for maximum 25 sec of duration.
- Whenever you hook-on the phone (before time out) the message is recorded.
- You may listen the recorded message you read by dialling 7446 85 100 41
All externals that were programmed for the DISA feature is answered by the voice
attendants.
The externals without DISA feature is routed directly to the operator .
The calls may be answered by the voice attendant if the call came from the external with the
DISA feature. DISA feature for an external line is entered by the program 93 ee 3 where ee
corresponds to the external number. To cancel it one must enter 93 ee 2 .
The call from an external without DISA feature is routed to the operator.
- Message must be recorded in a quite place before the exchange is given to the service.
- After entering the message code, 4 second dial tone is given for the preparation. You start
reading the message immediately after the tone stops.
- The message must be terminated before the maximum duration reached. The message is
terminated by hooking on the cradle of the phone by hand ( otherwise the noise is also
recorded).
- If the message you read is longer than the maximum duration you hear the congestion
tone. You must re-record.
- If you want to leave silence time at the end of the message you just wait and hook-on the
phone.
When the exchange in the night service the voice attendant may serve the calls.
7447 8510072 (default) Voice attendant does not serve for the night service.
7447 8510073 Voice attendant serve also during the night service.
7447 8510070 Voice attendant reads the message 7 and release the line.
7447 8510071 (default) Voice attendant does not read the message 7 for night service .
You may active the exchange to read the 7 th. message at any time.
The voice attendant answers the call by reading the 7 th. message ( If the message is
recorded for maximum duration it cuts the call immediately after reading the message).
7447 913 Voice attendant reads the message 7 and release the line.
7447 914 (default) Voice attendant works as standard.
It is possible to program the exchange so the first ten internal line may be called by the voice
attendant by a single digit. (The internal numbers 0,101-109 is called as 0,1-9)
7447 8510074 The first ten subscribers is called by the single digit.
7447 8510075 (default) The first ten subscribers is called with the directory number.
It is possible to make voice channel out of service for maintenance purposes or in case
failure of some channels for STAR1. To make the voice channels out of service
If the voice attendant can not serve to all incoming calls because of the heavy
traffic the calls are routed to the operator telephone.
It may be needed to restrict some internal terminals not to be called by the outside calls ;
7447 99 aaa 6 Subscriber may not be callable through the voice attendant.
7447 99 aaa 7 (default)Subscriber may be callable through the voice attendant.
MULTİTEK STAR1 INSTALLATION AND SYSTEM
: 10.10.2004
FEATURES : 56/83
DYF02 DOORPHONE
DYF04 AND TS702T VIDEODOORPHONE
It is possible to connected as many as required number of door phone to the exchange. The
door phones are connected to the exchange as the telephone with two wire .The door phone
terminals are programmed with 82 aaa 7/6 codes. The door phone is called by its terminal
number.
The calls can not be transferred to the door phones. But it is possible to call door phones
from outside with DISA or Voice Attendant feature. In that case, the call duration is limited to
3 minutes.
The door phones that may be connected to the exchange are following types:
Mini printer is a serial printer to down load the call information to the exchange. It works
with 220VAC power and it is connected to the exchange with two cables.
( Note : Polarity of wires is important. If it is wrong connected, the printer does not work ).
Connect the mains power to the printer. If the connection is correct printer starts working.
Enter the related programs to the exchange for printing various type of call data.
See the programming section of the exchange for more details about the printer programs.
MULTİTEK STAR1 INSTALLATION AND SYSTEM
: 10.10.2004
FEATURES : 58/83
Calling number
00902164203838
Date 15/01 13:36 (01) CID Memory no
Time CALL
(T1) (T2) (T3) (T4)
KTS300 screen
The numbers are reviewed by up and down buttons (T2, T3).(Note: you may see empty
memories at the beginning) When you hook-on the phone the calling information disappears.
When the number is seen on the screen if you press CALL (T4) the exchange starts calling
the number and then you talk. When you hook-on the phone caller id screen disappears.
MULTİTEK STAR1 INSTALLATION AND SYSTEM
: 10.10.2004
FEATURES : 60/83
KTS-300
Operator Console and Key Telephone Set
LCD
PARK
OTOCALL
T1 T2 T3 T4
Handset PARK S
MEMCALL 1 2 3
OTOMEM
4 5 6
CONF
M1
FLASH
7 8 9
M2
REDIAL
M3 * #
HOLD HOOK-OFF
M4 HF
1.General :
KTS-300 key telephone set may be connected to the exchanges as an operator console set.
It may also be used as a key telephone set connected to the internal lines of the exchange.
The number of KTS-300 set that may be connected to the exchanges is twenty .
3.Preparation of KTS-300 :
-Connect one side of the spiral cord to the handset and the other side to the handset jack
located at the button of the telephone cabinet.
-Adjust the desired ring level to L (low) or H (high) .
After those adjustments the telephone is ready to be connected to the exchange.
MULTİTEK STAR1 INSTALLATION AND SYSTEM
: 10.10.2004
FEATURES : 61/83
It is recommended to use 6 wire flat cable (6xAWG26/7FLAT) between the connection boxes
and telephones. After installing the cable between the two set , 6P/6C type plugs are inserted
to the ends of the cable. The cables used must be in the same order for two sides.
DIAL NUMBER
MULTİTEK STAR1 INSTALLATION AND SYSTEM
: 10.10.2004
FEATURES : 62/83
You dial the internal number that KTS-300 is connected to. While your hear the busy tone
on the earphone the following message is seen on the screen:
OKEY
If you do not see that message either you dial the wrong internal number or you connected
the set to the wrong cable.
If you hook-on the set and then hook-off you see the screen of the telephone is working as
receiving the message as DIAL e .t .c .
The LCD of the telephone is 4 line x 16 characters dot matrix display. Each line shows the
followings:
from an area without the CID service you see UNAVAILABLE information on the
screen.
STAR1 exchanges have 50 calling line memories.
Calling number
00902164203838
Date 15/01 13:36 (01) CID Memory no
Time CALL
(T1) (T2) (T3) (T4)
KTS300 screen
The numbers are reviewed by up and down buttons (T2, T3).(Note: you may see empty
memories at the beginning) When you hook-on the phone the calling information disappears.
When the number is seen on the screen if you press CALL (T4) the exchange starts calling
the number and then you talk. When you hook-on the phone caller id screen disappears.
T1,T2,T3,T4 buttons
Default: They are used to seize the external lines1 to 4.
If you press another Tx button when you are in conversation with an external line the new
external is seized and the other is released. When you are in conversation with an external
line if you press M1-M4internal line call buttons the external is hold on and the internal is
called automatically. If you hook on the phone the call is transferred to the called internal line.
b) T1-T4 may also be used for seizing the other external lines by programming. For example,
it is possible to program T1 button for seizing the external 6.
OTO CALL
If a called external number is busy and you press the OTO CALL button you see on the
screen WILL CONNECT message. You hook-on the phone. The wandering arrows are seen
on the screen , indicating that the exchange keeps calling the number. When the called party
starts ringing your telephone rings and you talk.
MEM CALL
To call a number recorded inside of the special or common memory of the exchange ,press
MEM CALL button and the dial the memory number. The exchange calls that number and
you talk.
OTO MEM
If you want the exchange to connect you a number recorded inside of the exchange memory
you press OTO MEM and dial the memory number. You see WILL CONNECT message on
the screen . You hook-on the phone The exchange calls the number and connects it. The
wandering arrows seen on the screen indicates that the exchange keeps calling the number.
M1,M2,M3,M4 buttons
Default values:
M1 to M4 buttons are initially used for calling the internal numbers as following table.
Button STAR1 STAR2
M1 Internal number 101 Internal number 11
M2 Internal number 102 Internal number 12
M3 Internal number 103 Internal number 13
M4 Internal number 104 Internal number 14
b) Programming M1-M4 buttons to call the numbers recorded inside the exchange
memory:
It is possible to program M1-M4 buttons to call the numbers recorded inside of the special or
common memory of the exchange.
Thus, you may call an external number by a single touch. For example, if M1 is programmed
for memory 56,when M1 is pressed the number in memory 56 called and talked.
PARK
During a conversation with an external line if you press PARK button the external line
becomes on hold and your telephone becomes free for other tasks by giving you the dial
tone. In that case ,for example, you may dial 6 to seize the another external line calling.
MULTİTEK STAR1 INSTALLATION AND SYSTEM
: 10.10.2004
FEATURES : 65/83
PARK S
It is used to re-seize the external lines parked before.
CONF
This button is used to make conference call with the internal or external lines .If you are
talking to an external or internal line and you want to add another internal or external line to
the conversation, press CONF, call the third party and re-press CONF button. You are in
conference.
FLASH
FLASH may be used to hold on the conversation.
(NOTE: If FLASH will be used to transfer the calls instead of * the flash feature of the
subscriber must be programmed at the exchange (program 7447 83 aaa /5)).
If the flash feature (600 ms) is not programmed the flash button cuts the conversation by
giving the dial tone.
REDIAL
To call the last external number that you dialled, press REDIAL and hold on .
HF (Hand free)
You can make calls or activate some features by pressing HF button without hooking-off the
handset. Some features of the telephone turns on the HF automatically when the related
button is pressed. (e.g. press T1 to seize the external T1 without hooking-off the handset)
WARN (Key 1)
If the called internal number is busy and you press WARN button , you inject a tone to the
earphone of the busy subscriber.
PICK UP (Key 6 )
If there is an incoming external call you may answer that by pressing PICK UP button.(To
use that feature, the telephone must be either hooked-off or HF pressed).
HOLD (Key *)
You may hold on a conversation by pressing * button.
Note that * pressing duration must be longer than the other digits.
HOOK-OFF (Key # )
When your phone is hook-off, pressing this button gives you dial tone.
Note that # pressing duration must be longer than the other digits.
KEYS PROGRAMMING
RESTORE DEFAULTS
TUR ENG FRA
ESC ENTER
All pages of programming mode has the same bottom line with the following functions;
To escape from the programming mode, you have to make either ESC,...ESC until reaching
to the main page or just hook-on the phone.
a) RESTORE DEFAULTS
Press PARK and CONF at the same time. The main page appears. Press T2 to select
RESTORE DEFAULTS and make ENTER by pressing T4 .The telephone becomes off and
the all data return to the factory set values.
b) LANGUAGE SELECTION
Press PARK and CONF at the same time. The main page appears. Press T2 to select
TUR ENG FRA fields. Tur corresponds to Turkish ,Eng to English and Fra to French. Make
ENTER .The telephone becomes off for a few seconds and the new language becomes
active.
c) PROGRAM KEYS
When PROGRAM KEYS line is flashing make ENTER (T4).The following screen appears. By
playing up and down (T1,T2 keys ) select the key that will be programmed and make ENTER
(T4).
T1 T2 T3 T4
M1 M2 M3 M4
ESC ENTER
1. T1-T4 Programming:
If you select one of T1-T4 and make ENTER you see the following screen.
Tx LINE NO
Tx GROUP NO
ESC ENTER
(Tx: T1-T4)
MULTİTEK STAR1 INSTALLATION AND SYSTEM
: 10.10.2004
FEATURES : 67/83
ENTER EXT NO
(PRESENT) (NEW VALUE)
VALUE --- ---
The external number value 01,02,03,....,12is entered by using the keypad digits. (Please be
sure about the maximum number of external connected to the exchange).
After making ENTER the new value is assigned to that key. If you make ESC before ENTER
you are back to the previous page.
If you enter the unvalid data and make enter ,the page does not change until you key the
valid data.
ENTER GROUP NO
(PRESENT) (NEW GROUP NO)
2. M1-M4 programming:
If you select one of M1-M4 on the program keys screen and make ENTER the following
screen appears:
ENTER Mx SUB NO
ENTER Mx MEMORY NO
ESC ENTER
Mx ENTER SUB NO
(PRESENT) ( NEW VALUE)
VALUE --- ---
ESC ENTER
ENTER Mx MEMORY NO
(PRESENT) (NEW VALUE )
VALUE --- ---
ESC ENTER
Note: You may stop the programming at any time by hooking-on the phone or making
ESC.. ESC. All programs changed and entered will be saved in the KTS-300 memory.
Some messages are shown on the screen depending on the feature used. Those messages
are usually self instructive such as NIGHT SERVICE , FOLLOW ME e. t. c. Other than the
messages ,there are two icons shown on the screen .
T1.............................T5 T11..........................T15
T6............................T10 T16..........................T20
0.............................104 140...........................144
105............................109 145...........................149
- - - -
- - - -
- - - -
- -
- - - -
- -
135 ...........................139 175............................179
BATTERY MODULE
If the main power of the exchange (220VAC) is often broken down it is necessary to add the
Battery Module to the exchange to back up the system power. The battery module works with
two pieces of 12V maintenance free battery up to 12 Amper hours capacity. When the mains
power is off the battery module supplies the exchange energy and when the power is on the
battery module charges the batteries.
MT26,STAR2 and STAR1 use the some battery module circuit.2x12V battery is connected to
module with a pair of cable with minimum 2x0.75 mm2 thickness.
The module connection to the exchange is done by a cable with two sides plugged.
-It is recommended not to connect more than 12 Amper hour capacity batteries to the
system. The exchange may have trouble to charge the batteries.
-If the battery cables are connected wrong side the 3A fuse on the board is blown out.
-When the battery voltage becomes less than 18V the module separates the battery from the
exchange. So it prevents to dry out the batteries.
-Note that connection of any type of battery other than the maintenance free battery may
cause problem to the system.
12V RING
+ - LED LED
PROGRAMMING MANUEL
OF STAR1 EXCHANGE
MULTİTEK STAR1 INSTALLATION AND SYSTEM
: 10.10.2004
FEATURES : 72/83
- Hook off the micro telephone and receive the dial tone.( “DIAL” is shown on the
display of the operator console.
- Dial programming code 7447.(“PROGRAM” is shown on the display.)
- And then, dial the codes which are given below in programming section.
- As long as you keep the telephone hook off you will be in programming mode;
no matter entered data is valid or not. If the entered data is valid the exchange
will give the ring-back tone. If not ,the busy tone will be given.
- After hearing the tone ( whether ring-back or busy ) you may go on next programming
procedures.
-After that, during your conversation, you may enter the programming codes
given below. Ring-back (or busy tone) will be heard after each valid (or unvalid ) code.
If you dial 7521 xytz * from the operator telephone the programming is locked
( xytz is the password given by you ). To enable the program one must re-enter 7521xytz*
When the exchange is locked , no one may enter the programming.
MULTİTEK STAR1 INSTALLATION AND SYSTEM
: 10.10.2004
FEATURES : 73/83
PROGRAMMING PROCEDURES
After receiving dial tone from number 0, the first dial programming code 7447 and then
following codes given bellow.
Abbreviations used:
80aaa0 Fully restricted (only callable and may call only operator).
80aaa1 Authorized to only local (internal) calls (outward restricted.)
80aaa2 Area call restricted (city call).
80aaa3 International call restricted (area call).
80aaa4 Unrestricted (DEFAULT).
80aaa5 Calls only common memory numbers.
80aaa6 Calls only common memory and city numbers.
80aaa7 External hot line (directly calls an external number given in memory number 99
or directly seize external line ) (unrestricted ).
80aaa8 Calls only city numbers and the numbers starting with 021(SPECIAL
APPLICATION)
80aaa9 Calls only the common memory numbers in memory 90-99.(For guards in a
factory)
82aaa0 Restricted.
82aaa1 Allowed (DEFAULT).
MULTİTEK STAR1 INSTALLATION AND SYSTEM
: 10.10.2004
FEATURES : 74/83
83aaa0 Authorized to make city call during the night or has a class of service as day.
83aaa1 Not authorized for night calls (DEFAULT ).
NOTE : If there is unused or un-exist external line it must be put out of service.
The same feature may be applied by dialling 7446 and 7448 from the operator (no need to
enter the programming)
When the system is in general night service:
a) When an incoming call is received from an external line, previously determined
MULTİTEK STAR1 INSTALLATION AND SYSTEM
: 10.10.2004
FEATURES : 78/83
number of subscribers are ringed at the same time (maximum 4 subscribers defined by
program 97 / default number 0).
Not: If you connect radio/CD player you cancel the built in music.
97 aaa....* where aaa: Maximum four (or less ) subscriber number (11,12,... ).
* : Transfer or hook –flash.
This program specifies the subscribers that will be ringed during the night service for
incoming calls.(Default number is 0. )
To cancel enter 97100*
Example: If one counter fee is 20 cents you enter 98002000.Please note that last
two digits has no meaning.
99 aaa 4 Incoming external call duration is restricted. The duration is defined by 99 aa 0-3.
MULTİTEK STAR1 INSTALLATION AND SYSTEM
: 10.10.2004
FEATURES : 79/83
952 is entered.
When necessary 952 resets the system retaining entered parameters unchanged.
953 Change the external and internal ring cadence of the exchange.
955 is entered.
Some times subscribers enter the pass – words to lock their telephones but latter
forget the pass-word .This program cancels all passwords entered by the sub-
scribers.
959 in entered.
All data entered related to the customer is cleared. (Exchanges becomes as out
of factory.)
MULTİTEK STAR1 INSTALLATION AND SYSTEM
: 10.10.2004
FEATURES : 80/83
When the ring button is pressed on the door phone this subscriber rings. This may be also
the video door phone TS702T.
External lines are tested and if broken they are put out of service.
HOTEL/MOTEL FEATURES
Operator dials 7441 then room number and then and then wake – up time from his
telephone set.
The operator enters 7441 105 0730.The printer prints the information for the
verification.
When the time enters becomes 07:30the telephone of the room 105 rings and when it is
hooked – off it gives a special warning tone. The wake – up service time is printed
out whether the room answer or not for the purpose of the verification.
When the customer leaves his room the operator by dialling 744781 aaa 7 prints
out the total of the charge counter ( check – out ).If a new customer moves to the
room the CHECK – IN is done again.
Example : If room number 255 corresponds to the exchange number 135 and the
customer quires 100 counter fee 7447 90 135 0100 is dialled and the result is
printed.
During each conversation of the customer the credit value is decreased. When the
credit ends the room telephone is restricted to the outside calls.
When the customer leaves the hotel the operator dials 7447 81 aaa 7 to make
CHECK – OUT. The printer prints our all relevant data including total counter and
credit value used.
FLEXIBLE NUMBERING
It is often required to change the exchange numbers according to the room
numbers of the hotel / motels. It is possible to use the flexible numbering feature
of the exchange to change terminal numbers.
It is possible to assign the following numbers to any terminal
- Numbers starting 1,2,3,4 ( up to 4 digits )
e.g 1 or 11 or 111 or 1111.
- Numbers 50,51,52,501-529.
- Numbers 61-65,67,68,69,601-619.
- Numbers 70,71,701-719.
NOTE :If you assign 11 to a room you may not assign 111 to any other place.