Professional Documents
Culture Documents
Amacan P Booklet
Amacan P Booklet
Amacan P
50 Hz
All rights reserved. The contents provided herein must neither be distributed, copied, reproduced,
edited or processed for any other purpose, nor otherwise transmitted, published or made available to
a third party without the manufacturer's express written consent.
Contents
3
Water: Water Transport
Submersible Pump in Discharge Tube
4 Amacan P
Water: Water Transport
Submersible Pump in Discharge Tube
▪ High reliability thanks to bearing temperature monitoring, ▪ that there is a sufficient liquid cover above the hydraulic
vibration sensor, thermal motor protection, leakage system (propeller) (shown in diagram depending on pump
sensors in the motor and connection space, and leakage size)
monitoring of the mechanical seal system. ▪ that the pump does not draw in air-entraining vortices
▪ Low-vibration hydraulic system; inlet ribs and optimised (shown in diagram depending on flow rate)
bellmouth for vortex-free inflow. ▪ that there is no cavitation in the hydraulic system (check
▪ Absolutely water-tight resin-sealed cable entries prevent against the NPSHrequired value indicated in the technical
any water from entering the motor – even in the event of literature).
a damaged cable. The following conditions must be met:
– NPSHavailable > NPSHrequired + safety allowance
1) If larger reserves are stipulated by local regulations or are required to compensate for uncertain factors in system
calculations, these larger reserves must be provided.
Amacan P 5
Water: Water Transport
Submersible Pump in Discharge Tube
Selection aid for material variants and fluid temperature per fluid
Comments, further recommendations
Max. permissible
[°C]
Material
variants
Screen4)
Waste water
▪ Industrial, corrosive, non-abrasive, slightly acidic; pH 40 G1 ⃝ ✔ 2-component high solid epoxy finish coat
value ≥ 6 (RAL 5002) 250 µm required
▪ Industrial, corrosive, non-abrasive, with lacquer/paint/ 40 G1 ⃝ - Lacquer/paint/varnish suspension = free of
varnish suspensions solvents
▪ Industrial, corrosive, non-abrasive fluids containing 40 G1 ✔ ✔ -
faeces
▪ Industrial, corrosive, non-abrasive fluids not 40 G1 ⃝ ✔ -
containing faeces
▪ Municipal, treated 40 G1 ⃝ ✔ -
Suspended solids, water/sand mixture 40 G1 ✔ - Up to 200 mg/l
Sludge 40 G1 ✔ - Up to 2 % dry solids content
Water, seawater and brackish water 255) G3 ⃝ - Use of anodes6) and 2-component high
solid epoxy finish coat (RAL 5002) 250 µm
required
Water, cooling water 40 G1 ⃝ - -
Water, surface water
▪ River water 40 G1 ✔ ✔ -
▪ No details specified 40 G1 ✔ ✔ -
▪ Lake water, fresh water 40 G1 ⃝ ✔ -
▪ Lake water, dam water 40 G1 ⃝ - -
Water, stormwater
▪ With strainer 40 G1 ⃝ - -
▪ Without strainer 40 G1 ✔ ✔ -
Water, raw water 40 G1 ⃝ - -
Water, contaminated water
2) Fluids to be pumped which are not listed in this table usually require higher-grade materials. Contact KSB.
3) Using a casing wear ring with a groove for flushing will reduce the efficiency by 2 % to 3 %.
4) See table "Openings of screen bars".
5) For t > 25 °C contact KSB (stainless steel variant).
6) Efficiency reduced by 2 % to 3 %; anode to be checked every 6 to 12 months
6 Amacan P
Water: Water Transport
Submersible Pump in Discharge Tube
Max. permissible
temperature
Material
variants
Screen4)
▪ Slightly contaminated water 40 G1 ⃝ - -
▪ Mixed water, with strainer 40 G1 ⃝ - -
▪ Mixed water, without strainer 40 G1 ✔ ✔ -
▪ Mixed water containing faeces 40 G1 ✔ ✔ -
▪ Mixed water not containing faeces 40 G1 ✔ ✔ -
Water, clean water 40 G1 ⃝ - -
2) Fluids to be pumped which are not listed in this table usually require higher-grade materials. Contact KSB.
3) Using a casing wear ring with a groove for flushing will reduce the efficiency by 2 % to 3 %.
4) See table "Openings of screen bars".
Amacan P 7
Water: Water Transport
Submersible Pump in Discharge Tube
8 Amacan P
Water: Water Transport
Submersible Pump in Discharge Tube
Related documents
▪ General Arrangement Drawings 1580.39
▪ Motor Data Booklet 1580.505
▪ Planning Information 0118.55
Amacan P 9
Water: Water Transport
Submersible Pump in Discharge Tube
Data to be indicated in the purchase order 1 Suspension arrangement attached to cover (or cross beam
for BU/BG)
▪ Designation of the pump
2 Lifting ring (standard, included in the scope of supply)
▪ Flow rate Q, head Htotal 3 Optional (intermediate) lifting ring(s)
▪ Head Htotal 4 Lower edge of discharge tube = lower edge of pump
▪ Type and temperature of the fluid pumped The support rope is an accessory and can be supplied with
additional lifting rings and a support spacer (⇨ Page 47) as an
▪ Voltage, frequency, starting method, cable length option. The standard design is supplied without intermediate
▪ Quantity and language of operating manuals lifting ring(s).
▪ Required accessories
– For discharge tubes indicate all required elevations
and the type of installation.
– For flow-straightening vanes indicate the type of
installation and whether the design is with or without
suction umbrella.
– For a support rope indicate dimension "L", the
number of additional lifting rings (depending on the
lifting height of the hoisting tackle) as well as the
elevations and type of installation.
10 Amacan P
Water: Water Transport
Submersible Pump in Discharge Tube
Material variants
Overview of materials
Part No. Description G1 G318)
(seawater variant)
112 Pump bowl EN-GJL-200 (JL 1030)
138 Bellmouth EN-GJL-200 (JL 1030)
230 Impeller 1.4517
350 / Bearing housing / bearing bracket EN-GJL-250 (JL 1040)
330
360 Bearing cover EN-GJL-250 (JL 1040)
412 O-ring NBR19)
(Viton-FPM)20)
433 Mechanical seal SiC /SiC (bellows NBR19),Viton - FPM20))
(pump end)
Mechanical seal SiC /SiC (bellows NBR19), Viton - FPM20))
(drive end)
502 Casing wear ring Stainless steel
571 Bail EN-GJS-400-15 (JS 1030)/S235JRG221)
811 Motor housing EN-GJL-250 (JL 1040)
812 Motor housing cover EN-GJL-250 (JL 1040)22)
818 Shaft (rotor) 1.4021 1.4057
834 Cable gland -
Gland housing EN-GJL-250 (JL 1040)
Various Screws/bolts Stainless steel
99-16 Anode - Zn
Other materials on request.
Notes on material
Duplex stainless steel (1.4517 or technically equivalent
material)
This type of cast steel is resistant to cavitation, has excellent
strength values and is used for high circumferential speeds. An
excellent resistance to pitting corrosion makes ferritic-
austenitic stainless steel a popular choice for pumping acidic
waste water with a high chloride content as well as seawater
and brackish water. Thanks to its good chemical resistance, e.g.
also against waste water containing phosphorous and
sulphuric acid, this material is used in a wide range of
applications in the chemical industry and and process
engineering. Pumps made of duplex stainless steel have a very
long service life, even when handling brines, chemical waste
water (pH 1–12), grey water and landfill leachate.
Comparison of materials
EN ASTM
EN-GJL-200 (JL 1030) A 48 Class 30 B
EN-GJL-250 (JL 1040) A 48 Class 40 B
1.4517 A 890 CD 4 MCu
1.4021 A 276 Type 420
1.4057 A 276 Type 431
NBR NBR
FPM FKM
EN-GJS-400-15 (JS 1030) A 536: 60–40–18
S235JR A 284 B
18) Pump set with cathodic protection (anodes to be checked every 6 to 12 months) and top coat of 250 µm
19) Nitrile rubber (Perbunan)
20) FPM fluorocarbon rubber variant available as an option against a surcharge
21) EN-GJS-400-15 (JS 1030) for motors: 80 6 … 205 6, 55 8 … 160 8, 40 10 … 120 10; all other motors: S235JR
22) For P1600-1060 in S235JR
Amacan P 11
Water: Water Transport
Submersible Pump in Discharge Tube
Selection chart
1000 Q [IM.gpm] 2000 3000 4000 5000 10000 20000 30000 40000 50000 100000
20
50
40
B4 800/900-540
B4 1500/1600-1060
10 B4 600-350 6 pol ① B4 1000-700
8 pol 12 pol
4 pol B4 1200-870
① 10 pol ① ① 30
B4 700-470
A4 1000-700
6 pol
① A4 800/900-540 8 pol A4 1200-870 A4 1500/1600-1060
10 pol 12 pol
6 pol
A4 700-470 ① ①
A4 600-350 6 pol ① ① 20
4 pol
5
① A4 1500/1600-1060
A4 1200-870 14 pol
A4 500-270
12 pol ①
4 pol ① A4 1000-700
① ①
4 10 pol
A4 800-540 ① G3 2200-1480
8 pol
A4 700-470 ① ②
3 10
8 pol
A4 600-350
6 pol ①
①
2 A4 500-270 G3 2200-1480
6 pol
① ②
5
H
[m] H [ft]
1
3
200 300 400 500 Q [m /h] 1000 2000 3000 4000 5000 10000 20000 30000 40000 50000
100 Q [l/s] 200 300 400 500 1000 2000 3000 4000 5000 10000
① Standard range
② Special range on request
12 Amacan P
Water: Water Transport
Submersible Pump in Discharge Tube
Characteristic curves
n = 1450 rpm
23°
9° 11° 13° 17° 19° 21°
15°
2
400 600 Q [m³/h] 800 1000 1200
35
10 23°
9° 13° 15° 21°
17° 19°
11° NPSH [ft]
R
NPSH [m]
R
20
5
15 20
P [kW]
P [hp]
10
23°
21°
10
19°
17°
5 15°
13°
9° 11°
23) These values are valid for a density = 1 kg/dm³ and a kinematic viscosity of up to 20 mm²/s.
Amacan P 13
Water: Water Transport
Submersible Pump in Discharge Tube
9° 11° 21°
13° 15° 17° 19°
1000 1200Q [m³/h]1400 1600 1800 2000 2200 2400 2600 2800
50
NPSH [m]
R
10
NPSH [ft]
R
10
2
60 80
P [kW]
60
40
P [hp]
40
20 21°
19°
13° 15° 17° 20
9° 11°
1000 1200Q [m³/h]1400 1600 1800 2000 2200 2400 2600 2800
K4200308s/2
24) These values are valid for a density = 1 kg/dm³ and a kinematic viscosity of up to 20 mm²/s.
14 Amacan P
Water: Water Transport
Submersible Pump in Discharge Tube
Qmin
70 70 η [%]
70 H [ft]
70
70 75
75
10 75
75 80
80
75 30
80
82.9
82.0
80 82.0
8
80.9
79.2
80
H [m] 80 80 80
6 75 20
75 75
75 75
70 70 70
70 70
18°
12° 14° 16°
4 10°
18°
10° 14° 16°
12° 40
10
NPSH [ft]
R
NPSH [m]
R
20
5
60 80
P [hp]
50
P [kW] 60
40 18°
16°
14°
30 12° 40
10°
25) These values are valid for a density = 1 kg/dm³ and a kinematic viscosity of up to 20 mm²/s.
Amacan P 15
Water: Water Transport
Submersible Pump in Discharge Tube
n = 960 rpm
Qmin
2.5 70 70
70 8
70
70 75 η [%]
75 75
70 75
70
75
70 75.8
2.0 78 76.9
75 78
78.3 75 6
77.2 78.2
75.9 78
74.4 78 75
73.3
1.5 H [ft]
75 75 70
75 75
70
H [m] 4
70 70
70 70
70 70
1.0 60
60
60
60 60 60
60 60
2
0.5
23°
9° 11° 13° 17° 19° 21°
15°
23°
13° NPSH [ft]
4 9° 15° 17° 21° R
19°
11°
NPSH [m] 10
R
6 8
P [kW]
4
P [hp]
4
23°
21°
2 19°
17°
15° 2
13°
9° 11°
26) These values are valid for a density = 1 kg/dm³ and a kinematic viscosity of up to 20 mm²/s.
16 Amacan P
Water: Water Transport
Submersible Pump in Discharge Tube
20
15 20
P [kW]
P [hp]
10
23° 10
21°
5
19°
15° 17°
9° 11° 13°
27) These values are valid for a density = 1 kg/dm³ and a kinematic viscosity of up to 20 mm²/s.
Amacan P 17
Water: Water Transport
Submersible Pump in Discharge Tube
23°
9° 11° 21°
13° 15° 17° 19°
9° 11° 40
13° 15° 17° 19° 21° 23°
10
NPSH [ft]
R
NPSH [m]
R
20
5
80
100
60
P [hp]
P [kW]
40
50
23°
21°
20 19°
13° 15° 17°
9° 11°
28) These values are valid for a density = 1 kg/dm³ and a kinematic viscosity of up to 20 mm²/s.
18 Amacan P
Water: Water Transport
Submersible Pump in Discharge Tube
η [%]
Qmin 80 80
80 80 H [ft]
80 83
8 83 83
80
83
80
84.4 84.7
83 83.8
83.3 83.8 82.3
6 82.2 83 20
83
83
H [m] 83 83
80 80 80 80 80
80 80
4
70 70
70 70 70 70
70
2
5
9° 11° 21°
13° 15° 17° 19°
NPSH [m] 50
R
10
10
150 200
P [kW]
P [hp]
100
100
50 21°
19°
13° 15° 17°
9° 11°
29) These values are valid for a density = 1 kg/dm³ and a kinematic viscosity of up to 20 mm²/s.
Amacan P 19
Water: Water Transport
Submersible Pump in Discharge Tube
2
5
9° 11° 21°
13° 15° 17° 19°
NPSH [m] 50
R
10
10
150 200
P [kW]
P [hp]
100
100
50 21°
19°
13° 15° 17°
9° 11°
30) These values are valid for a density = 1 kg/dm³ and a kinematic viscosity of up to 20 mm²/s.
20 Amacan P
Water: Water Transport
Submersible Pump in Discharge Tube
65
65 65 30
65 Qmin 70 η [%]
70 70 70
70 70
70 75 75
75 75
8 75
75 80 80 80
80 H [ft]
75
80
H [m] 80 82.7 81.3
84.8
83.9
80 84.0
6 82.8 80 20
81.0
80
80 80
80
80 80
75
75
75 75
75 75 75
4
70 70 22°
18° 20°
12° 14° 16°
10°
10
1500 2000 Q [m³/h] 2500 3000 3500 4000
22°
20° 35
18°
10 10° 14° 16°
12°
NPSH [ft]
R
NPSH [m]
R
20
100
80
100
P [kW]
60
22° P [hp]
20°
18°
16°
40 14°
12° 50
10°
31) These values are valid for a density = 1 kg/dm³ and a kinematic viscosity of up to 20 mm²/s.
Amacan P 21
Water: Water Transport
Submersible Pump in Discharge Tube
40
12
70
70 η [%]
H [ft]
10 Qmin
80
30
80
83
8 83.2
81.5
83
H [m]
80
80
6 20
70
10° 12°
4
2000 2500 Q [m³/h] 3000 3500 4000
10
NPSH [ft]
R
6 20
120 160
P [kW]
140
100
P [hp]
120
80
12°
100
10°
Free passage
Angle Free passage [mm] Angle Free passage [mm]
[°] [°]
12 92 10 85
32) These values are valid for a density = 1 kg/dm³ and a kinematic viscosity of up to 20 mm²/s.
22 Amacan P
Water: Water Transport
Submersible Pump in Discharge Tube
40
12 Qmin
70 70 70 70
70 70 η [%]
70 75 75
75 75
75 H [ft]
75
81 81
10 75 81 81
81 84 84
83.1 81.7 30
81 85.3
84 84.4
81 84.4 84 81
8 83.2 84 84
81.5 81
H [m] 81 81
81 81
81
75 20
6 75
75
75 75 75
75
70 22°
18° 20°
12° 14° 16°
10°
4
2000 3000 Q [m³/h] 4000 5000 6000
10
NPSH [ft]
R
20
200
P [kW]
150 200
22° P [hp]
20°
100 18°
16°
14°
12° 100
10°
33) These values are valid for a density = 1 kg/dm³ and a kinematic viscosity of up to 20 mm²/s.
Amacan P 23
Water: Water Transport
Submersible Pump in Discharge Tube
n = 725 rpm
9° 11°
13° 15° 17° 19° 21° 23°
6 20
NPSH [m]
R
4 NPSH [ft]
R
2
5
40
30 40
P [kW]
P [hp]
20
20
23°
21°
10
19°
11° 13° 15° 17°
9°
34) These values are valid for a density = 1 kg/dm³ and a kinematic viscosity of up to 20 mm²/s.
24 Amacan P
Water: Water Transport
Submersible Pump in Discharge Tube
6 70 70 20
70 70 Qmin
70 80 80
70 80 η [%]
70 80 83 83
70 80 83 83
80 83 H [ft]
80 84.6 84.3 84.3 83.7
4 80 83 84.2
82.6 83.6
81.8 83
83
H [m] 83 83 83 83 10
80 80
80 80
80 80 80
80
2 70
70 70
70 70 70 70
70
23°
21°
15° 17° 19°
9° 11° 13°
0 0
1000 2000 Q [m³/h] 3000 4000 5000
9°
17° 23° 40
11° 19°
13° 15° 21°
10
NPSH [ft]
R
NPSH [m]
R
20
5
100
60
P [hp]
P [kW]
40
50
23°
21°
20
19°
15° 17°
9° 11° 13°
35) These values are valid for a density = 1 kg/dm³ and a kinematic viscosity of up to 20 mm²/s.
Amacan P 25
Water: Water Transport
Submersible Pump in Discharge Tube
10
70 70
Qmin
80 η [%]
80 80 80
8 80 83
80 83 83
83
80 82.5
83 84.0
85.1
85.3
6 85.1 20
84.0 83
80
82.9 83
83 80
83 83
80
4 80 80 80 80 70
70
H [m] 70 H [ft]
70 70 70
70
2
19° 21°
15° 17°
9° 11° 13°
0 0
4000 5000 Q [m³/h] 6000 7000 8000 9000 10000 11000
10
NPSH [ft]
R
10
2
350
P [hp]
200
P [kW] 200
100 21°
19°
17°
15°
13° 50
9° 11°
36) These values are valid for a density = 1 kg/dm³ and a kinematic viscosity of up to 20 mm²/s.
26 Amacan P
Water: Water Transport
Submersible Pump in Discharge Tube
40
12
Qmin
η [%]
75 75 75
75 H [ft]
75
75 80 80
80
10 75 80
80 83 83
83
80 30
83
84.2 82.8
86.4
80 85.5
83
85.5
8
84.3 83
82.5
83 80
H [m] 83 83
83 80
80 80 80
6 80 80 20
75 75
75 75 75
75 75
22°
18° 20°
12° 14° 16°
10°
4
3000 4000 Q [m³/h] 5000 6000 7000 8000 9000 10000
10
NPSH [ft]
R
20
5
300 400
P [hp]
250
300
200
P [kW] 22°
20°
18°
150 200
16°
14°
12°
10°
100
3000 4000 Q [m³/h] 5000 6000 7000 8000 9000 10000
K4200368s/1
37) These values are valid for a density = 1 kg/dm³ and a kinematic viscosity of up to 20 mm²/s.
Amacan P 27
Water: Water Transport
Submersible Pump in Discharge Tube
n = 580 rpm
70 70
6 Qmin 20
80 80 η [%]
80 80
80
83
80 83
83 83 H [ft]
80 81.9
83.4
83 84.5
4 84.7 83
83.4 84.5
80
82.2 83
83
83 83 80
H [m] 10
80
80 80 80 80
70
70
2 70
70 70 70
70
19° 21°
15° 17°
9° 11° 13°
0 0
3000 4000 Q [m³/h] 5000 6000 7000 8000
NPSH [ft]
R
NPSH [m]
R
20
5
10
180
P [hp]
100
P [kW] 100
50 21°
19°
17°
15°
13°
9° 11°
20
38) These values are valid for a density = 1 kg/dm³ and a kinematic viscosity of up to 20 mm²/s.
28 Amacan P
Water: Water Transport
Submersible Pump in Discharge Tube
30
75 75
75
75 80
Qmin
8 75 80 80 η [%]
75 80
75 80 84
H [ft]
84 84
80
80 84
84 86.1 86.5 20
6 85.5 85.5
85.0 84.0
83.8
H [m] 84
84 84
84 84
4 80
80 80 80
80 80 80
75 75
75 75 75 10
75 75
9° 11° 21°
13° 15° 17° 19°
NPSH [m]
R 40
10
NPSH [ft]
R
20
300 400
P [kW]
P [hp]
200
200
21°
100
19°
13° 15° 17°
9° 11°
39) These values are valid for a density = 1 kg/dm³ and a kinematic viscosity of up to 20 mm²/s.
Amacan P 29
Water: Water Transport
Submersible Pump in Discharge Tube
Qmin
75 η [%]
75 75 75
75
10 75 80 80
75 80 80
80 84
84 84 30
80
84 84.7 83.3
80 86.9
86.0
8 84 86.0
84 H [ft]
84.8
83.0
H [m] 84
84 84 84 80
80
6 80 20
80 80
80 80
75 75
75 75 75
75 75
22°
18° 20°
12° 14° 16°
4 10°
10
NPSH [ft]
R
NPSH [m]
R
20
5
400
P [kW]
300 400
22°
20°
18° P [hp]
200 16°
14°
12°
10° 200
40) These values are valid for a density = 1 kg/dm³ and a kinematic viscosity of up to 20 mm²/s.
30 Amacan P
Water: Water Transport
Submersible Pump in Discharge Tube
n = 485 rpm
6 75 20
75
75 Qmin
75 80
75 80 80 η [%]
75 80
75 80 84
84 84
80
80 84 H [ft]
84 85.6 85.9
4 85.0 85.0 83.5
84.4
83.3
84
84 84
H [m] 84 84 10
80
80 80 80
80 80 80
75 75
2 75 75 75 75
75
9° 11° 21°
13° 15° 17° 19°
0 0
4000 6000 Q [m³/h] 8000 10000 12000 14000
NPSH [ft]
R
NPSH [m]
R
20
5
10
200
150 200
P [kW]
P [hp]
100
100
21°
50 19°
13° 15° 17°
9° 11°
41) These values are valid for a density = 1 kg/dm³ and a kinematic viscosity of up to 20 mm²/s.
Amacan P 31
Water: Water Transport
Submersible Pump in Discharge Tube
H [m] 84
84 84
84 84
84 84
4 80
80 80 80
80 80 80
75 75
75 75 75 75 10
75
9° 11° 21°
13° 15° 17° 19°
8000 10000Q [m³/h]12000 14000 16000 18000 20000 22000 24000 26000
NPSH [m] 50
R
10
10
600 800
P [kW]
600
400
P [hp]
400
200
21°
19° 200
13° 15° 17°
9° 11°
8000 10000Q [m³/h]12000 14000 16000 18000 20000 22000 24000 26000
K4200318s/2
42) These values are valid for a density = 1 kg/dm³ and a kinematic viscosity of up to 20 mm²/s.
32 Amacan P
Water: Water Transport
Submersible Pump in Discharge Tube
H [m] 84
84 84
84 84
84 84
4 80
80 80 80
80 80 80
75 75
75 75 75 75 10
75
65 65 65 65 65 65
2 65
9° 11° 21°
13° 15° 17° 19°
8000 10000Q [m³/h]12000 14000 16000 18000 20000 22000 24000 26000
NPSH [m] 50
R
10
10
600 800
P [kW]
600
400
P [hp]
400
200
21°
19° 200
13° 15° 17°
9° 11°
8000 10000Q [m³/h]12000 14000 16000 18000 20000 22000 24000 26000
K43226s/0
43) These values are valid for a density = 1 kg/dm³ and a kinematic viscosity of up to 20 mm²/s.
Amacan P 33
Water: Water Transport
Submersible Pump in Discharge Tube
Qmin 70 70
70
75 η [%]
75
10 75
80
80
30
84
80
84
8 86.5
85.3 H [ft]
83.5
H [m]
84 84
6 80 20
80 80
75 75 75
10° 14°
12° 40
10
NPSH [ft]
R
NPSH [m]
R
20
600
400
P [hp]
P [kW]
300 400
14°
12°
10°
44) These values are valid for a density = 1 kg/dm³ and a kinematic viscosity of up to 20 mm²/s.
34 Amacan P
Water: Water Transport
Submersible Pump in Discharge Tube
10
NPSH [ft]
R
20
5
600 800
P [hp]
P [kW]
600
400 22°
20°
18°
16°
400
14°
12°
10°
200
6000 8000 Q [m³/h]10000 12000 14000 16000 18000 20000 22000
K43229s/0
45) These values are valid for a density = 1 kg/dm³ and a kinematic viscosity of up to 20 mm²/s.
Amacan P 35
Water: Water Transport
Submersible Pump in Discharge Tube
n = 415 rpm
Qmin 75
75
80 80
75 80
75 80 84 84
84
75 80 η [%]
75 84 20
6 80
75 84
80
80 84
87.1 86.8 86.1
86.8
84
86.7
H [ft]
84 85.0
84.2 86.1
4
84
84
84
84
84 84 84
H [m] 84 80 10
80 80
80 80 80 75
80 80
75 75
2 75 75 75 75
75
23°
21°
15° 17° 19°
9° 11° 13°
0 0
6000 8000Q [m³/h]10000 12000 14000 16000 18000 20000 22000
10
NPSH [ft]
R
20
300 400
P [kW]
P [hp]
200
200
23°
21°
100
19°
15° 17°
9° 11° 13°
46) These values are valid for a density = 1 kg/dm³ and a kinematic viscosity of up to 20 mm²/s.
36 Amacan P
Water: Water Transport
Submersible Pump in Discharge Tube
75
75 Qmin
75 82 82
75 82
75 82 85 85 η [%]
85
6 75 82 85 20
75 86.5
82 85 86.5 86.5
82 86.8
85 86.5 87.1 86.1
82 86.8
86.7
86.5 H [ft]
85.0 86.1 86.5 86.5
84.2 86.5
4 85
85
85 85 85 85 82
82 10
H [m] 82 82
82 82 82
82 75
75 75
2 75 75 75 75
75
23°
21°
15° 17° 19°
9° 11° 13°
0 0
6000 8000Q [m³/h]10000 12000 14000 16000 18000 20000 22000
10
NPSH [ft]
R
20
300 400
P [kW]
P [hp]
200
200
23°
21°
100
19°
15° 17°
9° 11° 13°
47) These values are valid for a density = 1 kg/dm³ and a kinematic viscosity of up to 20 mm²/s.
Amacan P 37
Water: Water Transport
Submersible Pump in Discharge Tube
Dimensions
d4
h1
d1
h4
h2
45°
X
l1
h3
d2
d3
48) Pump set with 10-metre power cable (400 V) and 5-metre rope
38 Amacan P
Water: Water Transport
Submersible Pump in Discharge Tube
D
s1 45°
h7
d7
d8 A
d9
Amacan P 39
Water: Water Transport
Submersible Pump in Discharge Tube
d4
d1 h1
X
h4
h2
X
45°
l1
h3
d2
d3
49) Pump set with 10-metre power cable (400 V) and 5-metre rope
40 Amacan P
Water: Water Transport
Submersible Pump in Discharge Tube
D
s1 45°
h7
d7
d8 A
d9
49) Pump set with 10-metre power cable (400 V) and 5-metre rope
Amacan P 41
Water: Water Transport
Submersible Pump in Discharge Tube
42 Amacan P
Water: Water Transport
Submersible Pump in Discharge Tube
Installation types
Overview of installation types
BG discharge tube
BU discharge tube Overflow design with covered intake chamber
Overflow design with open intake chamber
DG discharge tube
DU discharge tube Underfloor discharge with covered intake chamber
Underfloor discharge with open intake chamber
Amacan P 43
Water: Water Transport
Submersible Pump in Discharge Tube
Scope of supply
Depending on the model, the following items are included in
the scope of supply:
▪ Pump set complete with 10 m power cable
▪ O-ring
▪ Back-up name plate
Accessories (optional):
▪ Support rope
▪ Accessories for cable support
- Spacer
- Turnbuckle
- Support spacer
- Shackle
- Cable clamps
▪ Cable support sleeves
▪ Flow-straightening vane to prevent floor vortices
▪ Discharge tube in various designs (steel or GFRP)
44 Amacan P
Water: Water Transport
Submersible Pump in Discharge Tube
Accessories
Amacan P 45
Water: Water Transport
Submersible Pump in Discharge Tube
Variant 1 Variant 2
Flow-straightening vane cast from concrete Steel section
s2
sR
s1
hR
hR
A
D
(e1) (e1)
lR lR
46 Amacan P
Water: Water Transport
Submersible Pump in Discharge Tube
59-8
59-17.2
59-24
720
59-47*
A A
59-7
59-17.1
*= The number of (intermediate) lifting rings depends on the lifting height of the hoisting tackle and on the building structure.
(Intermediate lifting rings are supplied as an option).
List of components
Part No. Description Material
59-8 Turnbuckle Stainless steel
59-17.2 Shackle Stainless steel
59-47 (Intermediate) lifting ring(s) Stainless steel
59-24 Rope, low rotation design Stainless steel
720 Spacer EPDM
59-17.1 Shackle Galvanised steel (stainless
steel optional)
59-7 Support spacer GFRP
Amacan P 47
Water: Water Transport
Submersible Pump in Discharge Tube
2 6
5 4
OW 380 091-00
List of components
Part No. Description Part No. Description
1 Cable clamp (approximately every 400 mm) 4 Support rope 59-24
2 Control cable 5 Spacer
3 Power cable 6 Clamp cover
4 3
A 2 6 5 1 6
OW 380 836-00
48 Amacan P
Water: Water Transport
Submersible Pump in Discharge Tube
List of components
Part No. Description
1 Discharge tube cover50)
2 Cover
3 Welding sleeve
4 Threaded bush with cable entry to DIN 22419 with strain relief and protection against kinking and twisting
5 Eyeplate for fastening the cable support (support rope)
6 Gasket, e.g. rubber with fabric reinforcement
X A-A
A -- A
A
A 1 5 6 8 4 7
OW 380 861-00
List of components
Part No. Description
1 Discharge tube cover51)
2 Transit frame (cable gland)
3 Packing and insert blocks
4 Cover segment with cable gland
5 Closed-cell profile joint in groove between the two cover parts
6 Sealing arrangement of groove between the two cover parts
7 Support brackets for cover segment with cable glands
8 Gasket (e.g. rubber with fabric reinforcement)
Amacan P 49
Water: Water Transport
Submersible Pump in Discharge Tube
571
834
412
412 812
412 350
818
811
(80--1)
360
412
350
112
412
412
230
433
138
502
0W 380 600-00
List of components
Part No. Description Part No. Description
112 Pump bowl 502 Casing wear ring
138 Bellmouth 571 Bail
230 Impeller 811 Motor housing
350 Bearing housing 812 Motor housing cover
360 Bearing cover 818 Shaft (rotor)
412 O-ring 834 Cable gland
433 Mechanical seal - -
50 Amacan P
Water: Water Transport
Submersible Pump in Discharge Tube
Amacan P 700-470
Amacan P 800-540
Amacan P 900-540
Amacan P 1000-700
Amacan P 1200-870
Amacan P 1500-1600
Amacan P 1600-1060
Motor version: UTG/XTG
V
412
834
571
82-5
812
412 330
818
811
(80--1)
360
412
V
350
112
412
412
230
433
138
502
UG 1132000
List of components
Part No. Description Part No. Description
112 Pump bowl 502 Casing wear ring
138 Bellmouth 571 Bail
230 Impeller 811 Motor housing
330 Bearing bracket 812 Motor housing cover
350 Bearing housing 82-5 Adapter
360 Bearing cover 818 Shaft (rotor)
412 O-ring 834 Cable gland
433 Mechanical seal - -
Amacan P 51
23.05.2013
1580.5/12-EN
KSB Aktiengesellschaft
P.O. Box 200743 • 06008 Halle (Saale) • Turmstraße 92 • 06110 Halle (Germany)
Tel. +49 345 4826-0 • Fax +49 345 4826-4699
www.ksb.com