Professional Documents
Culture Documents
619.5 619.6
619.5 619.6
INSTRUKCJA SERWISOWA
SERVICE MANUAL
ODKURZACZ TYP 619.5; 619.6
VACUUM CLEANER TYPE 619.5; 619.6
1
Sposoby oznaczania typów odkurzacza
Marking the types of the vacuum cleaner
619. .
Wykonanie / Design: Filtr wylotowy / Outlet filter:
5 - ze zwijaczem / with rewinder E - elektrostatyczny /
6 - bez zwijacza / without electrostatic
rewinder S - klasy S / S class
Bp
Wp P
Zd
Wm C
~230 M
2
SCHEMAT POŁĄCZEŃ ELEKTRYCZNYCH ODKURZACZA TYP 619.5
VACUUM CLEANER 619.5 ELECTRIC DIAGRAM
Bp
Wp P
~230
Wm C
Uz M
3
Rysunek części i podzespołów typ 619.6.XXXE, 619.5.XXXE, 619.5.XXXS
Parts and components drawing type 619.6.XXXE, 619.5.XXXE, 619.5.XXXS
4
Tabela wykazu części i podzespołów odkurzacza typ 619.6 i 619.5; 619.5S
List of parts and components for vacuum cleaner type 619.6 i 619.5; 619.5S
5
Przegroda – filtr
15 BARRIER 519.0019 5900215783185 x x x CZARNY BLACK 1
piankowy
16 Osłona dolna BOTTOM GUARD 519.0011 5900215780146 x x x CZARNY BLACK 1
17 Uszczelka filtra FILTER GASKET 619.0261 5900215811468 x -- -- 1
Filtr powietrza
18 OUTLET AIR FILTER 519.0052 5900215779584 x x -- --
1
wylotowego
Złącze 2-POLE
19 225.0400 -- x -- -- 1
dwubiegunowe CONNECTOR
20 Odciążka STAY WIRE 39.0017 -- x -- -- 1
Płytka
21 PLATE 519.0032 -- x 1
przyłączeniowa
Przewód
22 POWER CORD 42.4071 5900215792972 x CZARNY BLACK
przyłączeniowy 1
23 Zwijacz przewodu CORD REWINDER 269.0 5900215786360 x x -- -- 1
Przewód
24 CONNECTION WIRE 519.0101 5900215794099 x x CZARNY BLACK 1
przyłączeniowy
25 Ramka FRAME 519.5047 5900215531274 x x -- -- 1
5900215929897 CZARNY BLACK
26 Wnęka kpl. PLUG POCKET 519.5045 5900215867861 x x ZIELONY GREEN 1
5900215927640 CZERWONY RED
27 Bezpiecznik kpl. FUSE 619.0148 5900215799780 x x x -- -- 1
2
Przewód wewnętrzny L- 60mm / 0.5mm
28 INTERNAL WIRE x x x -- -- 1
kpl. 6.3 - 1
Zespół przewodów SET OF PUMP
29 619.0060 5900215531243 x x x -- --
1
pompki WIRES
30 Kolanko ELBOW 619.0007 5900215786346 x x x -- -- 1
31 Amortyzator pompki PUMP WIRE SET 619.0008 5900215792729 x x x -- -- 2
32 Pompka PUMP 619.0145 5900215799766 x x x -- -- 1
33 Kolanko (Pipeta) ELBOW-PIPETTE 619.0149 5900215799797 x x x -- -- 1
Amortyzator SELF-ADHESIVE
34 519.0129 5900215531267 x x x -- -- 1
samoprzylepny SHOCK ABSORBER
35 Osłona pompki PUMP GUARD 619.0047 5900215531229 x x x -- -- 1
36 Wężyk PIPE 619.0036 5900215794037 x x x -- -- 1
6
37 Uszczelka GASKET 619.0046 5900215523811 x x x -- -- 1
5900215815954 CZARNY BLACK
38 Blokada INTERLOCK 519.0008 5900215868325 x x - ZIELONY GREEN 1
5900215531342 CZERWONY RED
39 Sprężyna SPRING 875.0026 -- x x - -- -- 1
5900215814551 CZARNY BLACK
OUTLET FILTER
40 Osłona wylotu 519.0013 5900215868332 x x x ZIELONY GREEN 1
GUARD CZERWONY RED
5900215927596
OUTLET FILTER
41 Filtr ‘’HEPA’’ 619.0190 5900215810478 x -- -- 1
"HEPA"
5900215942704 CZARNY BLACK
OUTLET HEPA
42 Osłona filtra klasy S 619.0069 5900215531359 x ZIELONY GREEN 1
FILTER GUARD CZERWONY RED
5900215942711
5900215790657 CZARNY BLACK
43 Podstawa BASE 519.0001 5900215868301 x x x ZIELONY GREEN 1
5900215927565 CZERWONY RED
44 Zawór z wężykiem VALVE WITH PIPE 619.0048 5900215802084 x x x -- -- 1
45 Koło przednie kpl. FRONT WHEEL 2000.0022 5900215793313 x x x CZARNY BLACK 2
5900215531366 CZARNY BLACK
46 Koło tylne kpl. REAR WHEEL 519.0045 x x x CZERWONY RED
2
5900215531380
5900215872612 CZARNY BLACK
47 Osłonka WHEEL CAP 519.0004 5900215881478 x x x ZIELONY GREEN 2
5900215982601 CZERWONY RED
Uchwyt zbiornika FRONT CONTAINER
48 519.0024 5900215790305 x x x PLATYNOWY PLATINUM 1
przedni HANDLE
5900215529592 CZARNY BLACK
49 Gniazdo węża HOSE SOCKET 519.0065 5900215892436 x x x ZIELONY GREEN 1
5900215531397 CZERWONY RED
50 Uszczelka gniazda SEAT GASKET 519.0064 5900215779614 x x x -- -- 1
51 Kołek PIN 519.0025 -- x x x -- -- 1
5900215822372 PLATYNOWY PLATINUM
52 Zbiornik przedni FRONT CONTAINER 519.0223 x x x CZARNY BLACK
1
5900215531403
5900215962849 SZARY DARK GREY
53 Uchwyt HANDLE 519.0036 x x x CZERWONY RED
1
5900215927619
54 Osłona wyłącznika SWITCH GUARD 519.0040 5900215794303 x x x POPIELATY LIGHT GREY 1
7
Wyłącznik H8350
55 SWITCH H8350 07.0428 5900215804255 x x x -- -- 1
AB -ARCOLECTRIC
56 Osłona wyłącznika SWITCH GUARD 619.0033 5900215793122 x x x -- -- 1
Wyłącznik H8303
57 SWITCH H8303 07.0429 5900215523835 x x x -- --
AB -ARCOLECTRIC 1
58 Uchwyt wyłącznika SWITCH HANDLE 519.0041 5900215864228 x x x POPIELATY LIGHT GREY 1
5900215962863 CZARNY BLACK
59 Pokrywa COVER 619.0034 5900215817392 x x x ZIELONY GREEN 1
5900215918310 CZERWONY RED
5900215779423 CZARNY BLACK
60 Zaczep pokrywy COVER CATCH 519.0033 x x x SZARY DARK GREY
1
5900215823904
61 Uszczelka GASKET 519.0009 5900215779430 x x x -- -- 1
5900215872582 CZARNY BLACK
62 Pokrywa górna UPPER COVER 519.0035 5900215868349 x x x ZIELONY GREEN 1
5900215927602 CZERWONY RED
63 Filtr wodny kompletny WATER FILTER CPL 619.0450 5900215531410 x x x -- -- 1
Kondensator
64 CAPACITOR 519.0093 -- x x x -- -- 1
WXP-224K/EPCOS
część handlowa
65 Oring 20x3 ORING 20x3 07.0556 commercial x x x -- -- 1
component
część handlowa
66 Oring 8x1,5 ORING 8x1,5 07.0559 commercial x x x -- -- 1
component
część handlowa
67 Sprężyna Ø0.5 SPRING Ø0.5 619.0066 commercial x x x -- -- 1
component
część handlowa
Sprężyna pokrywy
68 COVER SPRING Ø1.2 519.0037 commercial x x x -- -- 1
Ø1.2 component
część handlowa
69 Opaska zaciskowa CLAMP BAND 619.0028 commercial x x x -- -- 2
component
część handlowa 8 619.6
SCREW
71 Wkręt ST 3,9x16-C-Z 01.0331 commercial x x x -- --
ST 3,9X16-C-Z component 6 619.5; 619.5S
część handlowa
72 Blachowkręt 3,9×25 SCREW 3,9X25 01.0341 commercial x x x -- -- 26
component
8
Wyposażenie odkurzacza
Vacuum cleaner equipment
9
Wykaz wyposażenia odkurzacza serii 619
List of equipment for vacuum cleaner type 619
10
Rysunek części i podzespołów zwijacza przewodu typ 269.0000
Parts and components drawing cord rewinder type 269.0000
11
Tabela wykazu części i podzespołów zwijacza przewodu typ 269.0000
List of parts and components cord rewinder type 269.0000
12
Rysunek części i podzespołów filtra kpl. typ 619.0450
Parts and components drawing filter cpl. type 619.0450
13
Tabela wykazu części i podzespołów filtra kpl. typ 619.0450
List of parts and components filter cpl. type 619.0450
14
DEMONTAŻ ODKURZACZA I PODZESPOŁÓW
15
Demontaż zbiornika przedniego
Demontaż wyłączników
- Zwolnić przycisk zaczepu 60, podnieść pokrywę górną 62 i odkręcić cztery wkręty 71.
- Ściągnąć uchwyt 53, oddzielić pokrywę 59 od pokrywy górnej 62 poprzez odłączenie
wiązki przewodów od wyłączników 55 i 57.
- Wcisnąć lekko zaczepy uchwytu wyłącznika 58 i wyciągnąć uchwyt razem z wyłącznikiem
55 (57) oraz osłonką 54 (56).
- Z uchwytu wyłącznika 58 zdjąć osłonkę 54 (56) i wypchnąć wyłącznik 55 (57).
- Zwolnić przycisk zaczepu 60 , podnieść pokrywę górną 62, wyjąć zbiornik przedni 52
i zbiornik tylny 2.
- Odkręcić cztery wkręty 71 znajdujące się w pokrywie górnej 62 i ściągnąć uchwyt 53.
- Poprzez odłączenie wiązki przewodów elektrycznych od wyłączników 55 i 57 oddzielić
pokrywę 59 od pokrywy górnej 62, ścisnąć zaczepy przelotki rurki giętkiej kpl. 10
i przepchnąć ją przez otwór pokrywy górnej 62.
16
- Odkręcić cztery wkręty 72 łączące zaczep lewy 7 i zaczep prawy 8 z osłoną górną silnika
9; odchylić zaczepy 7, 8 i usunąć pokrywę górną 62 z zaczepem pokrywy 60 i sprężyną
pokrywy 68.
- Odkręcić cztery wkręty 72 mocujące pas boczny 6; podnieść pas boczny do góry i nie
odłączając wężyka 36 od króćca wlotu 4, położyć go obok podstawy 43.
- Przełożyć wtyczkę przewodu przyłączeniowego przez otwór znajdujący się we wnęce kpl.
26; usunąć wnękę kpl. 26.
- Otworzyć osłonę wylotu 40 i wyciągnąć ją razem z filtrem powietrza wylotowego 18; nie
rozłączając połączeń elektrycznych delikatnie zdjąć cały zespół (tj. osłonę górną 9, osłonę
dolną 16, agregat ssący 12) z tulejowych żeber podstawy 43; umieścić go na podstawie
i odłączyć przewody elektryczne od styków pierścieniowych kpl. zwijacza przewodu 23.
- Odłączyć w/w przewody elektryczne od styków zwijacza i wyciągnąć zwijacz przewodu 23
z rowków podstawy 43.
- Rozwinąć przewód przyłączeniowy 24 nawinięty na szpulę, odchylić zaczepy labiryntu
i wypchnąć go ze szpuli; odłączyć przewód przyłączeniowy 24 od styków U i wyciągnąć go
z labiryntu.
- Zwolnić przycisk zaczepu pokrywy 60, następnie podnieść pokrywę górną 62 i wyjąć
zbiornik przedni 52 oraz zbiornik tylny 2.
- Odkręcić cztery wkręty 71 znajdujące się w pokrywie górnej 62 i ściągnąć uchwyt 53.
- Oddzielić pokrywę 59 od pokrywy górnej 62 poprzez odłączenie wiązki przewodów
elektrycznych od wyłączników 55 i 57, ścisnąć zaczepy przelotki rurki giętkiej kpl. 10 i
przepchnąć ją przez otwór pokrywy górnej 62 .
- Odkręcić cztery wkręty 72; odchylić zaczepy 7, 8 i usunąć pokrywę górną 62 z zaczepem
pokrywy 60 i sprężyną pokrywy 68.
- Odkręcić cztery wkręty 72 mocujące pas boczny 6. Podnieść pas boczny do góry i nie
odłączając wężyka 36 od króćca wlotu 4, położyć go obok podstawy 43.
- Odkręcić cztery wkręty 72 łączące osłonę górną 9 z osłoną dolną 16. Usunąć osłonę
górną 9, uszczelkę górną 11 i wyciągnąć agregat ssący 12.
- Odłączyć od agregatu ssącego przewody elektryczne.
Demontaż pompki
- Zwolnić przycisk zaczepu pokrywy 60, następnie podnieść pokrywę górną 62 i wyjąć
zbiornik przedni 52 oraz zbiornik tylny 2.
- Odkręcić cztery wkręty 71 znajdujące się w pokrywie górnej 62 i ściągnąć uchwyt 53.
- Oddzielić pokrywę 59 od pokrywy górnej 62 poprzez odłączenie wiązki przewodów
elektrycznych od wyłączników 55 i 57, ścisnąć zaczepy przelotki rurki giętkiej kpl. 10 i
przepchnąć ją przez otwór pokrywy górnej 62 .
- Odkręcić cztery wkręty 72; odchylić zaczepy 7, 8 i usunąć pokrywę górną 62 z zaczepem
pokrywy 60 i sprężyną pokrywy 68.
- Odkręcić cztery wkręty 72 mocujące pas boczny 6, a następnie zdjąć pas boczny 6 z
podstawy 43 i odłączyć wężyk 36 od króćca wlotu 4.
- Podnieść agregat do góry (zabudowany) i wyciągnąć: osłonę pompki 35, pompkę 32.
- Odłączyć od pompki: zespół przewodów pompki 29, bezpiecznik kpl. 27.
- Zdemontować: kolanko 33 z wężykiem 36, kolanko 30 z wężykiem i opaską zaciskową 69
oraz amortyzatory 31.
17
MONTAŻ ODKURZACZA TYP 619
UWAGI
18
Ewentualne uszkodzenia odkurzaczy typ 619
Objawy
Lp Przyczyny uszkodzenia Sposób naprawy
uszkodzenia
Brak napięcia w gniazdku Sprawdzić czy jest napięcie w
gniazdku
1. Odkurzacz nie Uszkodzony przewód przyłączeniowy lub Zdemontować odkurzacz, sprawdzić
pracuje lub wewnętrzne połączenia elektryczne przewód przyłączeniowy i
pracuje z wewnętrzne połączenia elektryczne.
przerwami Usunąć usterki lub wymienić na
nowe uszkodzone przewody.
Połączenia wykonać wg schematu
połączeń elektrycznych
Uszkodzony wyłącznik Wymienić wyłącznik
Zły styk szczotki z komutatorem w
wyniku zabrudzenia Postępować wg Instrukcji demontażu
Duże zużycie szczotek lub zawieszanie i napraw oraz Katalogu części
się szczotek w szczotko trzymaczu zamiennych
Zwarcie lub przerwa w uzwojeniu wirnika agregatów ssących
Przerwa w uzwojeniu stojana
Uszkodzenie łożysk
2. Nadmierne Nadmierne nagrzewanie się agregatu Postępować wg Instrukcji demontażu
nagrzewanie się ssącego i napraw oraz Katalogu części
odkurzacza zamiennych agregatów ssących
3. Małe podciśnienie Uszkodzona uszczelka Wymienić uszczelkę na nową
Nadmiernie zabrudzony filtr piankowy Oczyścić filtr piankowy
Postępować wg Instrukcji demontażu
Zwarcie lub przerwa w uzwojeniu wirnika
i napraw agregatów ssących
4. Woda nie Osadzenie się kamienia lub Udrożnić zatkane miejsca lub
wypływa ze zanieczyszczeń na zaworze w zbiorniku wymienić elementy na nowe
spryskiwacza lub tylnym, zatkana szczelina w
wypływa z małą spryskiwaczu
prędkością
- Komplet wkrętaków
- Lutownica elektryczna
- Kleszcze do obnażania przewodów
- Woltomierz kl. 1.5 zakres 0÷300V
- Watomierz kl.1.5 zakres 100/200/300V , 5/10A
- Amperomierz kl.1.5 zakres 5/10A
19
DISASSEMBLY OF VACUUM CLEANER AND ITS COMPONENTS
20
Removing the front container
Undo the two screws 72, which secure the front container handle 48 in the pin 51;
undo the two screws 71, and pull out the socket and gasket 50.
To remove the rear container remove the cap 1 and undo the valve 3. Remove o-ring
65 from the valve.
- From the upper plate 4 remove the grid 3 and take out the inlet filter 2.
- Remove the upper cover from the body 5.
- Remove: paper bag 16, gasket 7, 1 and detach the filter holder 11.
- From the body catches remove the following: foam filter 12, and gasket 6 from the side
wall of the body.
- Turn back the filter body and remove from its catches the cap 10, filter cartridge I 8 or filter
cartridge II 9.
- Undo the two screws 72, remove the setting plate 15, float 14 with gasket 13.
- Detach the labyrinth 10 and pull out the connection wire 1 and contacts 9.
- Remove the ring embedment 12 (for this purpose, lift up the embedment from the bottom
with a flat screwdriver).
- Remove slip rings 11 and 13 from the ring embedment.
- From the body 8 remove: spool 1, spring 6, lever 7.
- From the spool remove: spring 3, bearing 2.
- Release the catch switch 60, lift the upper cover 62 and undo the four screws 71.
- Remove the handle 53, detach the cover 59 from the upper cover 62 by disconnecting
wiring harnesses from switches 55 and 57.
- Gently press the catches of the switch handle 58 and pull out the handle along with the
switch 55 (57) and switch guard 54 (56).
- Remove the guard 54 (56) from the switch handle 58 and push out the switch 55 (57).
- Release the catch switch 60, lift the upper cover 62, remove the front container 52 and
rear container 2.
- Undo the four screws 71 in the upper cover 62 and remove the handle 53.
- By disconnecting the wiring harness from the switches 55 and 57 detach the cover 59 and
upper cover 62, tighten the catches of the flexy tube grommet. 10 and push it through the
opening in the upper cover 62.
21
- Undo the four screws 72, which connect left catch 7 and right catch 8 with the upper cover
9; unfold catches 7, 8and remove the upper cover 62 with cover catch 60 and spring 68.
- Undo the four screws 72, which secure the side strip 6; lift up the side strip and, without
detaching the pipe 36 from the inlet stub pipe 4 put it next to the base 43.
- Pull the plug of the power cord through the opening located in the pocket 26; remove the
pocket 26.
- Open the outlet cover 40 and pull it out with the exhaust air filter 18; without disconnecting
electrical wires gently remove the entire set (i.e. upper cover 9, bottom cover 16, suction
unit 12) with base fins 43; place it on the base and disconnect electrical wires from ring
contacts of the cord rewinder 23.
- Disconnect electrical wires from contacts of the cord rewinder and remove the cord
rewinder 23 from the base grooves 43.
- Unwind the power cord 24 wound on the spool, unfold catches of the labyrinth and push it
out of the spool; disconnect the power cord 24 from U contacts and pull it out of the
labyrinth of.
- Release the cover catch switch 60, lift the upper cover 62, remove the front container 52
and rear container 2.
- Undo the four screws 71 in the upper cover 62 and remove the handle 53.
- Detach the cover 59 from the upper cover 62 by disconnecting the wiring harness of the
electrical wires from the switches 55 and 57, tighten the catches of the flexy tube grommet
10 and push it through the opening in the upper cover 62.
- Undo the four screws 72, unfold catch 7, 8 and remove the upper cover 62; with the cover
catch 60, and spring 68.
- Undo the four screws 68, which secure the side strip 6; lift up the side strip and, without
detaching the pipe 36 from the inlet stub pipe 4, put it next to the base 43.
- Undo the four screws 72, which connect the upper cover 9 with the bottom cover 16.
Remove the upper cover 9, upper gasket 11 and suction unit 12.
- Disconnect electrical wires from the suction unit.
- Undo the four screws 72, which secure the side strip 6, remove the side strip 6 from the
base 43 and detach the pipe 36 from the inlet stub pipe 4.
- Lift up the suction unit (built-in) and remove: Pump cover 35, pump 32.
- From the pump, remove: Set of pump wires 29, fuse 27.
- Remove: elbow-pipette 33 with pipe 36, elbow 30 with the pipe and clamp band 69 and
shock absorber 31.
22
ASSEMBLY OF THE VACUUM CLEANER TYPE 619
Assemble the vacuum cleaner in reverse order to disassembly. At the same time
observe the below notes and use the catalogue drawing.
Particular attention should be paid to correct connection of the inner wiring in
accordance with the wiring diagram.
On installing all components sealed with rubber gaskets make sure the gaskets
tightly adhere to the mated parts, as it is the precondition for the correct operation of the
vacuum cleaner.
Assemble the cord rewinder in reverse order to disassembly. The following sections
include some information related to the installation of individual parts:
when embedding the spring set in the spool an arrow on the rack should overlap
the small projection on the flange of the spool,
make sure that the spring rack is carefully pushed into spool clips,
before installing the embedment of the rings on the body axis, apply a layer of
industrial-grade petroleum jelly to the ring track,
upon winding the cable onto the spool tighten the spring by rotating the spool
fivefold.
NOTES
1. Any repairs can be carried out only after the device is disconnected from the mains.
2. Repairs and maintenance should be carried out by a qualified employee, only after
reading the operating manual of the product and this manual.
3. The heating of the suction assembly during extended periods of use is normal.
Maintenance check is required if the suction assembly warms up too rapidly.
4. For proper operation of the suction assembly, it must be periodically inspected,
particularly thorough removal of dust from the assembly with particular emphasis on
the commutator and brush plates is required and worn brushes must be replaced.
5. We do not ship individual parts
6. We reserve the right to change the shape of the parts to improve the quality and
functionality of the product.
23
Potential damage to the vacuum cleaner type 619
4. Water does not Scaling or dirt on the valve in the rear Remove the clogging or replace the
flow out of the container, clogged fissure in the spray components
spray nozzle or nozzle
flows out at a
slow rate
LIST OF TOOLS
– A set of screwdrivers,
– Electric soldering iron,
– Pliers for baring wires,
– Voltmeter class 1.5, range 0-300 V,
– Wattmeter class 1.5, range 100/200/300 V, 5/10,
– Ammeter class 1.5, range 5/10.
24