Professional Documents
Culture Documents
Radar Pre-Quotation-Instalation Questionaire
Radar Pre-Quotation-Instalation Questionaire
Radar Pre-Quotation-Instalation Questionaire
Pre-Survey Checklist
The successful installation and accurate quotation for a Radar relies upon the accurate provision of
information relating to navigation equipment fitted (or to be fitted) in the vessel concerned.
To assist in this initial process the following details are requested: -
II-POWER REQUIREMENTS
Emergency Generator Yes [ X ] NO [ ] Is a UPS Required Yes [ X ] NO [ ]
Vessels 230V [ X ] Spare Breaker
main/emergency available at the Yes [ ] NO [ ]
110V [ ]
voltage Emergency Power
Distribution Panel
Note A : Vessels with GT =>10,000 T , should have a CAT-I ( 23” Display ) Radar as per IMO requirements
III-NAVIGATION EQUIPMENT
Station Satcom Pte Ltd,
30 Cecil Street,
#19-08 Prudential Tower,
Singapore
2
1 D/GPS #1
Make JRC
Model JRC/ JLR-7700
Is Signal connected to old Radar Yes [ X ] NO [ ]
If No is a NMEA Buffer available with Yes [ ] NO [ ]
spare output?
2 D/GPS #2
Make JRC
Model JRC/ JLR-7700
Is Signal connected to old Radar Yes [ X ] NO [ ]
If No is a NMEA Buffer available with Yes [ ] NO [ ]
spare output?
3 Gyro Compass
Make TOKIMEC
Model TOKIMEC/ TG-6000
Is Signal connected to old Radar Yes [ X ] NO [ ]
If analogue Gyro, is any converter Yes [ ] NO [ ]
with spare outputs available? Gyro Converter needed [ ]
4 Speed Log
Make JRC
Model JRC/JLN 202 & JRC/ JWW-5
Is Signal connected to old Radar Yes [ X ] NO [ ]
If PPM analogue signal, is any Yes [ ] NO [ ]
converter with spare outputs Speed log to NMEA converter is needed [ ]
available?
5 AIS
Make FURNO
Model FURNO/ FA-150
Is Signal connected to old Radar Yes [ ] NO [ X ]
If NO is a Spare output available or a Spare O/P [ ] NMEA Buffer needed [ ]
NMEA Buffer is needed?
6 Echo Sounder “ Optional for MFD “
Make JRC
Model JRC/JFE-380
Is a NMEA output available? Yes [ ] NO [ ]
7 Anemometer“ Optional for MFD “
Make TYPE – B,NIPPON ELECTRIC INSTRUMENT
Model
Is a NMEA output available? Yes [ ] NO [ ]
8 ECDIS“ Optional “
Make JRC
Model JRC/ JAN-901B
Is Old Radar Connected to ECDIS Yes [ X ] NO [ ]
If Yes , Type of connection : Radar Over Lay [ X ] ARPA Targets[ ]
9 VDR
Make RUTTER
Model RUTTER, VDR-100G3
Is Old Radar Connected to VDR Yes [ ] NO [ ]
If Yes , Type of connection : VGA [ ] DVI [ ] 5-BNC [ ] Special Connector [ ]
Is any additional interface kit/cables Yes [ ] NO [ ]
will be required?
10 Other Radar Onboard
Make
Model
Is Old Radar inters witched to the Yes [ ] NO [ ]
other Radar
V- SCANNER MOUNTING
Are old scanners mounted on Main Mast [ X ] Individual Mast [ ]
A- Height of the handrail and could it obstruct the B
array movement. [ 100 ]
B- Distance from mid of the current pedestal to the
Main mast and could it obstruct the array A
movement. [ 150 ]
VI-Location of Equipment
Photos, Sketches & Plans are important as they give much better overview than a long text.
a) Sketch
Kindly locate on the below grid the proposed location for the Radar as well as location of equipment listed in III
b) Photos
Kindly provide photos for the following:
1. Full Bridge view from Starboard Side.
2. Full Bridge view from Port Side.
3. Proposed location for the Radar Display.
4. Proposed location for the Radar Scanner.
5. General photos for the equipment listed in III.
6. Suggested cable penetrations for various signals.
7. Head Panels needed to be opened.
8. Suggested cables routes especially for the Scanner cables.
c) Plans :
Estimated Distances between the following:
From Radar Display Proposed Location to Emergency Power Distribution Panel 2.2 m.
D/GPS#1 Buffer 2.2 m.
D/GPS#2 Buffer 2.2 m.
Gyro Signal Distribution 5.2 m.
AIS Distribution box AIS fitted top of the X- band
radar display
Speed Log 5.20 m.
Notes:
Vessel has two RADAR
1. X band (with ARPA) –JMA-9253-7CA
2. S band (without ARPA) – JMA 9303