Professional Documents
Culture Documents
Hp-A 510 Top Weighting Arm SCT 3412ne1102
Hp-A 510 Top Weighting Arm SCT 3412ne1102
Hp-A 510 Top Weighting Arm SCT 3412ne1102
s
Technical News
The HP-A 50 top weighting arm was designed for Drafting System Settings:
worsted ring spinning machines with 3-roller double
max. total drafting zone: h’+v’ 222 mm
apron drafting systems with and without EliTeQCom-
max. distance A’ 290 mm
pactSet.
min. distance e 68 mm
Application: Back zone v’ min./max. 40/69 mm
Main zone h’ min./max. 53/82 mm
Spinning of wool, man-made fibres and blends of up
to 20 mm staple length.
The HP-A 50 top weighting arm consists of top arm
body, weighting lever, 3 weighting units and clearer
roller support, or without the latter in case of machines
with EliTeQCompactSet.
SCT.342 NE .02
Features
Weighting Components HP-C Top Apron Cradles
Each top roller is held by a weighting unit consisting SUESSEN top apron cradles HP-C allow quick and
of the spring support, the leaf spring and the top roller trouble-free replacement of the top aprons.
retainer with wide contact area for reliable guidance The cradles can be easily fitted and removed.
of the top rollers. The leading edge of the metal cradle is equipped with
an anti-friction clip.
The weighting units allow direct and friction-free
weighting of the top rollers. The leaf spring prevents The HP-A 50 top weighting arm can be equipped
sideforces on the top rollers. with the cradles HP-C W70 and HP-C W0 (chart ).
The top roller retainers are machined after assembly
Cradle Nip Point Slip
of the top weighting arms to ensure alignment of
Drafting Drafting
top rollers and bottom rollers. Adjustment is not
necessary. up to 70 mm
HP-C W 70
fibre length
Even under load, each weighting unit can be easily up to 20 mm
adjusted to the desired position by loosening the up to 00 mm fibre length
HP-C W 0
fixing screw. fibre length
Fig. 2
1 loaded 2 partly-raised
2
HP-C Top Apron Cradles
TW R B Top Apron
Cradle
B
40,5 mm mm mm mm
HP-C 7540 W 70 75
HP-C 8240 W 70 82.5
HP-C 9040 W 70 90 55.1 40.5 63 x 40 x
R
Cradle Spacers
X
Cradle Spacers
mm
brown 3.5
grey 4
yellow 5
blue 6
x
beige 7
black 8
Chart 2
3
HP-R Top Rollers
TW
14 TW Y
Top Roller
mm mm
HP-R 7019 KH 70 100
Ø 19
TW Y
Top Roller
mm mm
HP-R 7540 FHRU . . . 75 5
HP-R 8240 FHRU . . . 82.5 22.5
HP-R 9040 FHRU . . . 90 30
HP-R 0040 FHRU . . . 00 40
HP-R 040 FHRU . . . 0 50
4
Maintenance of HP-R Top Rollers (with black end caps)
Relubrication Inject approx. cm3 lubricating grease through the hole in the end cap.
Clean the grease point.
Recommended
lubricator SUESSEN lubricator with pointed adapter
Fitting:
Setting Sequence
5
3 3 3 . Set the Weighting Pressure on
All Top Rollers
Use:
– the spanner (4 or 5)
– the hexagon key (2)
Fig. 6
6
2. Set the Height on all Top Weighting Arms
Use:
– the gauge (8)
– the torque wrench (9)
– the screw driver (0)
7
3. Set the Distances of the Top Rollers
on the Master Top Arm
Use:
– the spanners (4 or 5)
– the caliper gauge
π The master top arm must be loaded. Use spanners
(4 or 5) to loosen the screws (6) of the weighting
units to be set approximately /4 turn.
π Use the caliper gauge to set the top roller distan-
ces according to the values shown in the
SUESSEN setting chart.
π Tighten the screws (6).
Use:
– the gauge ()
Fig. 9 – the key (4)
π Remove top aprons with cradle from the middle
11 12 13 top roller.
π Loosen fixing screws (2) of gauge () with key
(4).
π Place the gauge on the closed top arm and push
stop elements (3) onto the top roller arbors
(Fig.0).
π Tighten the fixing screws (2).
The top roller setting has been transferred to the
gauge.
s
π Use spanners (4 or 5) to loosen the screws (6) of
the weighting units approximately /4 turn.
π Place gauge () on the open top arm and push
the top rollers into the stop elements (3).
π Close the top arm and tighten screws (6).
π Remove the gauge with the top arm being closed.
Technische Änderungen vorbehalten. Reserva-se o direito de alterações técnicas. Teknik deǧişimlerin hakkı bizde saklıdır.
Technical modifications reserved. Reservado el derecho de introducir modificaciones técnicas. Con riserva di modifiche tecniche.