Professional Documents
Culture Documents
Ar6020 6023 6026 6031 - Im
Ar6020 6023 6026 6031 - Im
Feb
INSTALLATION MANUAL
CODE: 00ZAR6020/I2E
DIGITAL MULTIFUNCTIONAL
SYSTEM
AR-6020/6023
AR-6020D/6023D
AR-6020N/6023N
MODEL AR-6026N/6031N 2
CONTENTS
Parts marked with " " are important for maintaining the safety of the set. Be sure to replace these parts with
specified ones for maintaining the safety and performance of the set.
CONTENTS
2 [2] AR-6020/6023/6020D/6023D/6020N/6023N/6026N/6031N
(MAIN UNIT)
1. Installing conditions. . . . . . . . . . . . . . . . . . . . . . . . 2- 1
2. Removal of protective material and fixing screw. . 2- 1
3. Installing procedure. . . . . . . . . . . . . . . . . . . . . . . . 2- 1
4. Removal and storage of fixing screw . . . . . . . . . . 2- 3
5. Paper feed tray setup . . . . . . . . . . . . . . . . . . . . . . 2- 3
[3] AR-RP11(REVERSE SINGLE PASS FEEDER)
1. Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3- 1
2. Packed items check . . . . . . . . . . . . . . . . . . . . . . . 3- 1
3. Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3- 1
[4] MX-CS12/CS13 (500 SHEET PAPER FEED UNIT)
1. Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4- 1
2. Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4- 1
[5] AR-DS19/DS20(STAND LARGE/SMALL)
1. Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5- 1
2. Packed items check . . . . . . . . . . . . . . . . . . . . . . . 5- 1
3. Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5- 1
[6] AR-NB7(NETWORK EXPANSION KIT)
1. Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6- 1
2. Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6- 1
[7] MX-EB14 (EXPANSION MEMORY BOARD)
1. Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7- 1
2. Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7- 1
[8] MX-PK10(PS EXPANSION KIT)
1. Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8- 1
2. Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8- 1
[9] AR-PB10(PRINT EXPANSION KIT)
1. Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9- 1
2. Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9- 1
[10] Setting, Adjustments, Operation check
1. Firmware version check and version up . . . . . . . . 10- 1
2. Function and operation check . . . . . . . . . . . . . . . . 10- 1
[11] Necessary works before moving the machine . . . . 11- 1
Service Manual
Machine Environment, Installation and Transportation
If the installing (use) conditions are not satisfied, the machine may not If the voltage is outside the specified range, please have a certified
exhibit full performance, resulting in problems. It may also cause electrician upgrade the outlet.
safety problems. Using the following information, make sure all (Electrical work is required.)
aspects of installation, space, power, transportation, leveling, and
Use of a step-up transformer is also available. In this case, the capac-
safety are met.
ity must be great enough for the max. power consumption of the
No. Content machine.
A Transportation space
(3)Power frequency, waveform
B Installing space
C Power source (Capacity, voltage, frequency, safety, plug) The frequency must be within the range of the specified frequency +/-
D Floor strength 2%. If the power waveform is improper, a problem may occur with the
Direct rays of the sun, dust, temperature, humidity, gasses, machine.
E
chemicals, vibration
(4)Safety
F Note for handling PWB and electronic parts
Be sure to properly ground the machine.
A.Transportation space Grounding (earth connection) must be performed before inserting the
For installation of a large size machine, be sure to check that the door power plug into the power outlet.
size is wide enough before bringing in. When disconnecting the earth connection, be sure to disconnect the
power plug from the power outlet in advance.
B.Installing space
(5)Power plug
The following space must be provided around the machine in order to
assure machine performance and proper operations. Check the shape of the power plug of the machine, and insert it into a
power outlet of the acceptable shape.
If any option is installed, provide the additional space for with installa-
Power plug stated in power capacity.
tion.
Adequate space must be provide behind the machine for proper venti- D.Floor strength and level
lation of heat and dust. The machine will not function properly if heat
This machine is considerably heavy and becomes heavier with an
and dust cannot be properly expelled from the machine.
option installed.
The floor must be strong enough to safely support the weight of the
30 cm machine as well as any installed options.
If the unit is not properly leveled, toner density may become affected
degrading the copy / print quality.
Also, color shift or image distortion may occur.
To assure proper Image quality, make sure the machine is sitting level.
30 cm 45 cm
E.Direct rays of the sun, dust, temperature, humid-
ity, gasses, chemicals, vibration
C.Power source (Capacity, voltage, frequency, (1)Temperature and humidity (Environmental conditions)
safety, plug) This machine is designed to perform properly under the specified tem-
If the power specifications are not satisfied, the machine cannot exhibit perature and humidity. If the temperature and humidity exceeds the
full with performance and may cause safety trouble. specified range, the machine may not operate properly and or cause
equipment failure.
Strictly observe the following specifications.
Especially when the humidity is too high, paper absorbs humidity to
(1)Power capacity cause a paper jam or dirty copy.
Check that the following power capacity is satisfied. If not, additionally Do not install the machine near a heater, an air conditioning outlet, or a
provide a proper power source. humidifier.
Current capacity Condensation may form inside the machine causing multiple prob-
lems. Make sure machine has proper ventilation.
Japan: 20A or more
Humidity㧔RH㧕
EX 100V: 15A or more
85%
EX 200V: 10A or more
60%
20%
Check the shape of the power plug of the machine, and insert it into a
power outlet of the acceptable shape.
(2)Contaminates
If dust enters the machine, it may cause dirty copy and a paper jam,
resulting in a shortened lifetime.
(3)Direct sunlight
If the machine is installed in direct sunlight, the exterior of the machine
may be discolored and abnormal copies may be produced.
(5)Vibration
Avoid installation near a machine which produces vibrations.
If vibrations are applied to the copier machine, copy images may be
deflected and a trouble may be caused.
!2 20 -8 62
!2
$$ !2
."
!2
!2
..
-8 #3
-8 #3
-8 %"
-8
#3
!2
$3
!2 $3
B.Power source
-Use an exclusive to dedicated power outlet. If the power plug of this
machine is inserted into a power outlet commonly used with other
illumination units, flickers of the lamp may be result. Use a power outlet
which is not used commonly with any illumination units.
-Avoid complex wiring.
C.Grounding wire connection. 3) Remove the screw fixing the developer cartridge and disconnect the
harness of the developer.
-To avoid danger, the power outlet must be grounded. If no grounding
wire is connected and a leakage occurs, a fire or an electric shock may
be result.
6) Remove the developer cover from the developer cartridge. 10) Attach the developer cartridge to the main unit, and secure it with
the screw.
2
8) Check that two hooks of the developer cover is hooked on the toner
cartridge guide, and secure the toner cartridge guide to the 4 or 5 times
developing unit. Then, tighten up the screws of the developer cover.
2) Insert the toner cartridge along the guides until it locks in place while
Hook pushing the lock release lever
* Check that the DV seal is free from the developer. If developer is If there is any dirt or dust on the toner cartridge, remove it before
attached to the DV seal, clean it. installing the cartridge.
* After supplying developer, do not tilt or shake the developer
cartridge.
* Check that the both ends of the DV seals are not put in the developer
cover.
2 9) Connect the harness of developer cartridge to the developer
cover.
2) Hold the paper pressure plate and turn the fixing screw in the arrow
direction. 3) Use the [SIZE] key to select the paper size.
Fixing Screw
2) Push the pressure plate down until it locks in place. Push the centre
of the pressure plate down until it locks into place.
Partition(B)
Partition(A)
4) Move the document glass to the right side and remove the left OC
glass fixing plate
1 2 3 4 5
3. Installation
Turn the main switch of the machine to the “OFF” position and then
remove the power plug of the machine from the outlet.
5) Fix the SPF glass with caring the position of fixing boss.
1) Lift the document cover from the machine and tilt it to the rear side
to remove it.
10) Fix the harness with the clamp as shown in the figure.
7)Remove the rear cabinet and cut out the cut-out portion.
11) Pass the harness to the hole of the Rear cabinet and fix the rear
cabinet..
8)Attach the AR-RP11.
2 4
1 3 5 6 7
4) Fix the 2nd connection drive unit to the main unit with the screw
(Packed items M3x6S).
<Rear left>
<Rear right>
Attach the main unit with MX-CS12 and MX-CS13 with the
plates (Packed item Plate) and the screws (Packed items
M4x12P).
9) Pass the harness of MX-CS12 to the 2nd sheet. Then, bent and
hook the 2nd sheet as shown in the figure to cover the harness.
MX-CS13
MX-CS12
Fix the 2nd sheet to the PWB. C.Turn on the power of the main unit
1) Power to the main unit.
2) Turn ON the power switch.
MX-CS12
MX-CS13
[5]AR-DS19/DS20(STAND LARGE/SMALL)
1. Unpacking 2) <AR-DS19>
Put the MX-CS12 or MX-CS13 on the Stand. Fit the positioning pins of
Open the package and take out the stand. Then, check the packed the Stand (2 places) with the positioning holes of the MX-CS12 or MX-
items. CS13. At this moment, do not make contacted the main unit with the fix-
ing plate of the Stand. * The main unit needs to be connected with the
<AR-DS19> <AR-DS20> MX-CS12 or MX-CS13 when the MX-CS12 or MX-CS13 is fixed to the
Stand
Do not contact.
Fixing plate
Positioning pin
Fixing plate
Positioning pin
1 2 3
<AR-DS20>
Put the MX-CS12 or the main unit with the MX-CS12 on the Stand. Fit
the positioning pins of the Stand (2 places) with the positioning holes of
(AR-DS20) the MX-CS12.
5
(AR-DS19)
4
Positioning pin
3. Installation
1) Remove the tray of the MX-CS12/CS13.
3) <AR-DS19>
Fix the Stand with the MX-CS12 or the main unit with the MX-CS12 by
the Fixing screw B (2 pieces).
<AR-DS20> 6) Fix the Fixing plate Rear with caring the fixing direction as shown in
Fix the Stand to the MX-CS12 or MX-CS13 with the Fixing plate Front the figure and the Fixing screw A/B.
R/L with caring the fixing direction as shown in the figure and the Fixing <AR-DS19>
screw A/B.
Fixing screw B
Face up
the longer part.
Fixing screw B
Fixing screw A
Face up
the longer part.
Fixing plate Front L
Fixing screw A
<AR-DS20>
4) Fix the tray of MX-CS12 or MX-CS13.
8) Rotate the adjusters to fix the machine to the floor surface not to
move the machine.
<AR-DS19>
<AR-DS20>
1. Unpacking 2. Installation
Turn the main switch of the machine to the “OFF” position and then
remove the power plug of the machine from the outlet.
1)Remove the Rear cabinet.
3)Connect the harnesses of the network PWB unit to the MCU PWB as
shown in the figure
4)Fix the Network PWB unit and the saddle bracket to the main unit. On 7) Fix the scanner left cover bottom.
the left top fixing position, it is necessary to fix the RSPF plate if the
RSPF unit is installed into the machine.
Screw
(M3x8 S-Tight)
2 6) Cut the area of the Scanner cover shown in the following figure.
2. Installation
Turn the main switch of the machine to the “OFF” position and then
remove the power plug of the machine from the outlet.
4) Attach the Rear cabinet.
1) Turn off the power switches of the main unit.
1. Unpacking 3) From the [Device Setup] menu, click the [Product Key Setting]
under the [Device Management] menu.
1 2
Note: - N model 4) Select the [Printer Expansion Kit] from the [Option name], and input
the product key of the PCL license from the [Product Key]. Then,
To set up the PS driver, do not use the CD-ROM which is
click the [Submit].
included in the MX-PK10 but use the PCL CD-ROM which is
included in AR-PB10.Installation.
- S/D model
In the case of the S/D model, the PCL CD ROM is not packed
with the main unit. It is packed with the optional printer expansion
kit AR-NB7.
2. Installation
<Note before installation>
Note: To enable PS, the product key must be acquired. (For details of
the acquiring method of the product key, refer to the distributor.)
Write down the acquired product key on the product key sheet
and pass it to the user.
8) Select the [PostScript] from the [Option name], and input the prod- 4) Select the [PostScript] from the [Option name], and input the prod-
uct key of the PS license from the [Product Key]. Then, click the uct key of the PS license from the [Product Key]. Then, click the
[Submit]. [Submit].
9) Close the browser and restart the MFP. At this moment, the PS 5) Restart the MFP. At this moment, the PS function is activated.
function is activated.
10) Restart the MFP.
B. PS3 check
<S/D model> 1) Print the test page in PS3 fonts by the key operation of the opera-
1) Set the IP address of the MFP. tion panel. (Select the PS font list by the procedures described in
the data list print printer test page of the system setup guide.)
2) Input the IP address of the MFP into the browser.
Click the [Admin mode]. Check to confirm that printing is made normally.
!00,)#!4)/.
.5-"%2
-!#().%
3%2)!,
.5-"%2
02/$5#4
+%9
1. Unpacking
A. Packed items check
2. Installation
A. Enable setting of functions
1) Enter the product key to enable the functions.
a) Enter the system setting mode.
b) The machine enters the product key input mode.
c) Enter the product key.
d) Press the registration key.
2) After completion of the product key input, turn OFF the power
switch on the operation panel of the machine, and turn OFF
the main power switch.
3) Turn ON the main power switch and the power switch on the
operation panel.
Example:
<Solder composition code of lead-free solder>
p
Bi-Sn-Ag
“BATTERY DISPOSAL”
THIS PRODUCT CONTAINS A LITHIUM PRIMARY (MANGANESS DIOXIDE) MEMORY BACK-UP BATTERY THAT MUST BE
DISPOSED OF PROPERLY. PLEASE CONTACT YOUR LOCAL SHARP DEALER OR AUTHORIZED SERVICE REPRESENTATIVE
FOR ASSISTANCE IN DISPOSING OF THIS BATTERY.
U.S.A.AND CANADA ONLY
#/092)'(4 © "9 3(!20 #/20/2!4)/.
!LL RIGHTS RESERVED
0RODUCED IN *APAN FOR ELECTRONIC $ISTRIBUTION
.O PART OF THIS PUBLICATION MAY BE REPRODUCED
STORED IN A RETRIEVAL SYSTEM OR TRANSMITTED
IN ANY FORM OR BY ANY MEANS
ELECTRONIC MECHANICAL PHOTOCOPYING RECORDING OR OTHERWISE
WITHOUT PRIOR WRITTEN PERMISSION OF THE PUBLISHER
4RADEMARK ACKNOWLEDGEMENTS
v -ICROSOFT¤ 7INDOWS¤ 7INDOWS¤ 7INDOWS¤ -E 7INDOWS .4¤
7INDOWS¤ 7INDOWS¤ 80 7INDOWS¤ 6ISTA 7INDOWS¤ 7INDOWS ¤
7INDOWS¤ 7INDOWS ¤ 3ERVER 7INDOWS 3ERVER
¤
¤ 3ERVER AND )NTERNET %XPLORER ARE
7INDOWS ¤ REGISTERED TRADEMARKS OR
TRADEMARKS OF -ICROSOFT #ORPORATION IN THE 53! AND OTHER COUNTRIES
v 0OST3CRIPT IS A REGISTERED TRADEMARK OF !DOBE 3YSTEMS )NCORPORATED
v -ACINTOSH -AC /3 !PPLE4ALK %THER4ALK ,ASER 7RITER AND 3AFARI ARE REGISTERED
TRADEMARKS OR TRADEMARKS OF !PPLE #OMPUTER )NC
v )"- 0#!4 AND 0OWER 0# ARE TRADEMARKS OF )NTERNATIONAL "USINESS -ACHINES
#ORPORATION
v !CROBAT¤ 2EADER #OPYRIGHT¤
!DOBE 3YSTEMS )NCORPORATED !LL RIGHTS
RESERVED !DOBE THE !DOBE LOGO !CROBAT AND THE !CROBAT LOGO ARE TRADEMARKS OF
!DOBE 3YSTEMS )NCORPORATED
v 0#, IS A REGISTERED TRADEMARK OF THE (EWLETT
0ACKARD #OMPANY
v 3HARPDESK IS A TRADEMARK OF 3HARP #ORPORATION
v !LL OTHER TRADEMARKS AND COPYRIGHTS ARE THE PROPERTY OF THEIR RESPECTIVE OWNERS
SHARP CORPORATION
Business Solutions CS Promotion Center
First Edition : September 2014
Latest Edition : February 2015