Professional Documents
Culture Documents
Aplicatii Rezolvate: Sevadaclickpec, C, C, C
Aplicatii Rezolvate: Sevadaclickpec, C, C, C
Command: CIRCLE¬
Specify center point for circle or [3P/2P/Ttr (tan tan radius)]: 307.83,97.39¬
Specify radius of circle or [Diameter] <20.50>: 20.5¬
X = 323.80
Command: CIRCLE¬ Y = 238.33
Specify center point for circle or [3P/2P/Ttr (tan tan radius)]: 341.81, 117.0¬
Specify radius of circle or [Diameter] <20.50>: 20.5¬
X = 264.60
Y = 211.50
Command: CIRCLE¬ X = 264.54
Specify center point for circle or [3P/2P/Ttr (tan tan radius)]: Y = 211.44
307.83,138.17¬
Specify radius of circle or [Diameter] <20.50>: 20.5¬
Command: CIRCLE¬
X = 264.33
Specify center point for circle or [3P/2P/Ttr (tan tan radius)]: X = 264.64 Y = 151.48
264.33,151.48¬ Y = 148.50
Specify radius of circle or [Diameter] <20.50>: 105.3¬
X = 307.83
Y = 138.17
Command: CIRCLE¬ X = 319.14
Specify center point for circle or [3P/2P/Ttr (tan tan radius)]: 264.60,211.50
¬ Y = 117.03
Specify radius of circle or [Diameter] <20.50>: 65¬
C4
P2 X = 307.83
Y = 138.17
Command: EXTEND¬ X = 319.14
Current settings: Projection=UCS, Edge=None Y = 117.03
Select boundary edges ...¬ C2
Select objects or <select all>:se va da click pe C2, C3
X = 307.83
Y = 97.39
C1
X = 341.81
Y = 117.00
In continuare putem sa stergem linia ajutatoare.
Va trebui sa editam cele doua varfuri care nu se ating. Astfel daca dam click
pe C1 apoi pe patratelul din partea superioara (acest lucru este confirmat de
inrosirea patratelului) putem il tragem spre C2.
Continuare-pg3
Command: TRIM ¬
Current settings: Projection=UCS, Edge=None
Select cutting edges ¬
Select objects or <select all>:se va da click astfel ca desenul sa arate ca cel
alaturat X = 323.80
Y = 238.33
X = 264.60
Y = 211.50
X = 264.54
Y = 211.44
Command: CIRCLE¬
Specify center point for circle or [3P/2P/Ttr (tan tan radius)]: 3P¬ X = 264.33
Specify first point on circle: tan¬{se va da click pe P1} X = 264.64 Y = 151.48
Specify second point on circle:tan¬{se va da click pe P2} Y = 148.50
Specify third point on circle:tan¬{se va da click pe P3}
X = 307.83
Command: TRIM ¬ Y = 138.17
Current settings: Projection=UCS, Edge=None X = 319.14
Select cutting edges¬ P1 Y = 117.03
Select objects or <select all>:se va da click astfel ca segmentul albastru sa
dispara
X = 307.83
P3 Y = 97.39
P2
X = 341.81
Y = 117.00
Continuare-pg4
Aplicatii propuse
Aplicatia va avea aceleasi dimensiuni ca cea rezolvata anterior.
X = 210.00
Y = 148.50
NOTA:
Coordonatele x=210 y=148.5
reprezinta centrul piesei. Pentru a
muta piesa se va alege base point:
X = 264.60 Y = 148.50 urmata de
noile coordonate (210,148.5)
Pentru centru de rotatie la array
avem X = 209.85 Y = 151.50.