Professional Documents
Culture Documents
Engg Data Sheets Calc
Engg Data Sheets Calc
6 1 Pages 1
Ambient Design
7 Material Strength Strength Max ºF
8 SA-36 Plate 16,600 16,600 900 Carbon Steels
9 SA-106 B Seamless Pipe 17,100 17,100 1,000
10 SA-234 WPB Fittings 17,100 17,100 1,000
11 SA-105 Forging 20,000 18,894 1,000
12 SA-516 70 Plate 20,000 19,647 1,000
13 SA-414 G Sheet 21,400 21,400 900
14 SA-213 TP316L Sms Tube 16,700 14,330 850 Stainless Steel 316L
15 SA-240 316L Plate 16,700 14,330 850
16 SA-312 TP316L Sms. and Wld. Pipe 16,700 14,330 850
17 SA-403 316L Sms and Weld Fittings 16,700 14,330 850
18 SA-479 316L Bar 16,700 14,330 850
19 SA-213 TP316 Sms Tube 20,000 17,412 1,500 Stainless Steel 316
20 SA-240 316 Plate 20,000 17,412 1,500
21 SA-312 TP316 Sms. and Wld. Pipe 20,000 17,412 1,500
22 SA-403 316 Sms and Weld Fittings 20,000 17,412 1,500
23 SA-479 316 Bar 20,000 17,412 1,500
24 SA-213 TP304L Sms Tube 16,700 14,288 1,200 Stainless Steel 304L
25 SA-240 304L Plate 16,700 14,288 1,200
26 SA-312 TP304L Sms. and Wld. Pipe 16,700 14,288 1,200
27 SA-403 304L Sms and Weld Fittings 16,700 14,288 1,200
28 SA-479 304L Bar 16,700 14,288 1,200
29 SA-213 TP304 Sms Tube 20,000 12,547 1,500 Stainless Steel 304
30 SA-240 304 Plate 20,000 12,547 1,500
31 SA-312 TP304 Sms. and Wld. Pipe 20,000 16,971 1,500
32 SA-403 304 Sms and Weld Fittings 20,000 16,971 1,500
33 SA-479 304 Bar 20,000 16,971 1,500
34 SB-209 6061-T6 plate 0.051-0.249", wld 6,000 0 400 Aluminum
35 SB-209 6061-T651 plate 0.25-5", wld 6,000 0 400
36 SB-209 6061-T6 plate 0.051-0.249" 10,900 0 400
37 SB-209 6061-T651 plate 0.25-4.0" 10,900 0 400
38 SB-209 6061-T651 plate 4.0-5.0" 10,300 0 400
39 SB-211 A96061-T6 bar 0.125-0.249", wld 6,000 0 400
40 SB-234 A96061-T6 tubes 0.025-0.200", wld 6,000 0 400
41 SB-241 A96061-T6 sms. Pipe, wld 6,000 0 400
42 SB-247 A96061-T6 forging, wld 6,000 0 400
43 SB-308 A96061-T6 shapes, wld 6,000 0 400
44 Material properties are compliant with ASME Section IID Table 1A
45
46 Fluid Properties:
47 810.0 P [psi] - pressure at top of vessel
48 115.00 H [ft] - fluid height
49 0.940 SG - specific gravity
50 Pdesign [psi] = P+0.433*SG*H ~~ design pressure including static head 810+0.433*0.94*115 = 856.8073
51 Pdesign is to be used in the design of subsequent components (shell, head, nozzle, etc)
52 This sheet is for educational use only - use at your own risk.
8 Dimensions:
9 98.500 Do [in] - outside diameter Do
10 0.200 t [in] - nominal wall thickness
11 118.200 L [in] -length
12 0.000 Corr [in] - corrosion allowance t
Length
15 16,600 S [psi] - allowable stress
Long Seam
16 0.80 El - long seam efficiency (circ stress)
17 0.80 Ec - circ seam efficiency (long stress)
18 0.0% UTP [%] - undertolerance allowance
19 14.5 P [psi] - interior pressure
20 Calculated Properties:
21 Volume [cuft] = ((Do/2-t)^2)*pi()*L/1728 ((98.5/2-0.2)^2)*PI()*118.2/1728 = 517.01
22 Weight [lb] = (Do-t)*pi()*L*t*40.84/144 (98.5-0.2)*PI()*118.2*0.2*40.84/144 = 2070.49
23 Variables:
24 UT [in] = t*UTP 0.2*0 = 0.000
25 nt [in] = t-Corr-UT 0.2-0-0 = 0.200
26 Ri [in] = Do/2-nt 98.5/2-0.2 = 49.050
27 Required Thickness: UG-27(c)(1,2)
28 ta [in] = P*Ri/(S*El-0.6*P) ~~ long sem 14.5*49.05/(16600*0.8-0.6*14.5) = 0.054
29 tb [in] = P*Ri/(2*S*Ec+0.4*P) ~~ circ seam 14.5*49.05/(2*16600*0.8+0.4*14.5) = 0.027
30 Treq [in] = MAX(ta,tb)+Corr ~~ required minimum thickness MAX(0.054,0.027)+0 = 0.054
31 CheckTreq = Treq <= nt 0.054 <= 0.2 = Acceptable
32 Maximum Pressure: UG-27(c)(1,2)
33 Pint1 [psi] = (S*El*nt)/(Ri+0.6*nt) (16600*0.8*0.2)/(49.05+0.6*0.2) = 54
34 Pint2 [psi] = (2*S*Ec*nt)/(Ri-0.4*nt) (2*16600*0.8*0.2)/(49.05-0.4*0.2) = 108
35 PMax [psi] = Min(Pint1,Pint2) ~~ maximum allowed design pressure MIN(54,108) = 54.0
36 CheckP = PMax >= P 54 >= 14.5 = Acceptable
37 Treq provides a worst case required thickness for nozzle analysis for a nozzle located on the long seam or circ seam
38 This sheet will not calculate thick walled vessels Check → Not a thick walled vessel, calculations are valid
39 The UG-16(b) minimum thickness requirement has not been taken into consideration here.
40 This sheet cannot be used to check for allowable exterior pressure loads.
41 Use the Weld Efficiency program to calculate El and Ec
42 This sheet is for educational use only - use at your own risk.
17 Calculated Properties:
18 Approx. cone weight based on steel, lbs = 1061.7
19 Approx. cone volume , cuft = 16.87
20 a [rad] = ATAN((ODL-ODS)/(2*L)) ~~ alpha angle in ATAN((49.61-33.858)/(2*23.622))
radians = 0.322
21 angle [deg] = Degrees(a) ~~ alpha angle in degrees DEGREES(0.322) = 18.439
22 nt [in] = t-Corr ~~ thickness with corrosion allowance removed 1.18-0 = 1.180
23 Required Thickness: VIII-1 UG-32(g)
24 Treq [in] = P*ODL/(2*COS(a)*(S*E+0.4*P)) + Corr ~~required minimum thickness
25 870.2*49.61/(2*COS(0.322)*(19204*1+0.4*870.2)) + 0 = 1.164
26 CheckTreq = Treq <= t 1.164 <= 1.18 = Acceptable
27 Maximum Pressure: VIII-1 UG-32(g)
28 Pmax [psi] = 2*S*E*nt*cos(a)/(ODL-0.8*nt*cos(a)) ~~maximum allowed design pressure
29 2*19204*1*1.18*COS(0.322)/(49.61-0.8*1.18*COS(0.322)) = 882.6
30 CheckPMax = Pmax >= P 882.6 >= 870.2 = Acceptable
31 T provides a worst case required thickness for nozzle analysis for a nozzle located on the large end of the cone and located
32 on the long seam weld.
33 The UG-16(b) minimum thickness requirement has not been taken into consideration here.
34 Discontinuity checks which are required for each end of the cone when it is welded to a straight shell are not included
35 in this sheet.
36 This sheet cannot be used to check for allowable exterior pressure loads.
37 This sheet is for educational use only - use at your own risk.
8 Dimensions:
9 24.000 Do [in] - outside diameter of head
10 0.188 tb [in] - thickness before forming
11 0.159 tf [in] - thickness after forming (note 1)
12 0.010 Corr [in] - corrosion allowance
13 2.000 Skirt [in] - straight skirt length
14 Material and Conditions:
15 SA-240 304 Material
16 20,000 S [psi] - allowable stress
17 1.00 E - head longitudinal efficiency
18 50.0 P [psi] - interior pressure
19 Calculated Properties:
20 note 1: Suggested thickness after forming Approx. head weight based on steel, lbs = 43.56
21 0.125 in Approx. head volume including skirt, cuft = 1.52
22 Variables:
23 nt [in] = tf-Corr ~~ thickness with corrosion allowance removed 0.159-0.01 = 0.149
24 D [in] = Do-2*nt ~~ ID with corrosion allowance removed 24-2*0.149 = 23.701
25 h [in] = D/4 ~~ inside crown height 23.701/4 = 5.925
26 ho [in] = h+nt 5.925+0.149 = 6.075
27 D/2h = D/(2*h) 23.701/(2*5.925) = 2.000
28 Do/2ho = Do/(2*ho) 24/(2*6.075) = 1.975
29 Ro [in]= Kzero*Do 0.889*24 = 21.334
30 Required Thickness: App. 1-4(c), UG-37(a)(1)
31 App1-4(f) = tf/(Kone*D) 0.159/(0.9*23.701) = 0.0075
32 App1-4(f)Calc = if(AND(0.0005=<App1-4(f),App1-4(f)<0.002),"Calculation Required","Calculation not required")
33 App. 1-4(f) Calculation Not Required
34 Treq [in] = (P*D*K)/(2*S*E-0.2*P)+Corr ~~ required minimum thickness
35 (50*23.701*1)/(2*20000*1-0.2*50)+0.01 = 0.040
36 CheckTreq = Treq<=tf 0.04<=0.159 = Acceptable
37 Maximum Pressure: App. 1-4(c), UG-37(a)(1)
38 Pmax [psi] = (2*S*E*nt)/(K*D+0.2*nt) ~~ maximum allowed design pressure
39 (2*20000*1*0.149)/(1*23.701+0.2*0.149) = 251.8
40 CheckPMax = Pmax >= P 251.8 >= 50 = Acceptable
41 App. 1-4(f) calculation is not included on this sheet
42 The UG-16(b) minimum thickness requirement has not been taken into consideration here.
43 Nozzles may be subject to a smaller required thickness depending on location in the head.
44 Only the knuckle required thickness is calculated on this sheet
45 Heads may be subject to stress relief if large elongation occurs - UCS-79(d), UNF-79(d), UHA-44(d)
46 Use the Weld Efficiency program to calculate E
47 This sheet cannot be used to check for allowable exterior pressure loads.
48 This sheet is for educational use only - use at your own risk.
8 Dimensions:
9 98.425 Do [in] - outside diameter of head
10 98.425 L [in] - inside crown radius (note 1)
11 9.843 IKR [in] - inside knuckle radius (note 2)
12 0.787 tb [in] - thickness before forming
13 0.669 tf [in] - thickness after forming (note 3)
14 0.118 Corr [in] - corrosion allowance
15 2.000 Skirt [in] - straight skirt length
16 Material and Conditions:
17 SA - 36 Material
18 16,600 S [psi] - allowable stress
19 0.85 E - head longitudinal efficiency
20 101.5 P [psi] - interior pressure
21 Calculated Properties:
22 note 1:Suggested radius L per UG-32(j) 98.43 Approx. head weight based on steel, lbs = 2358.81
23 note 2:Suggested radius IKR per UG-32(j) 5.906 Approx. head volume including skirt, cuft = 60.62
24 note 3:Suggested thickness after forming 0.6690
25 Variables:
26 nt [in] = tf-Corr ~~ thickness with corrosion allowance removed 0.669-0.118 = 0.551
27 D [in] = Do-2*nt ~~ ID with corrosion allowance removed 98.425-2*0.551 = 97.323
28 L/r = L/IKR 98.425/9.843 = 10.000
29 M= 0.25*(3+sqrt(L/IKR)) 0.25*(3+SQRT(98.425/9.843)) = 1.541
30 Ro [in] = L+tb 98.425+0.787 = 99.212
31 Required Thickness: App. 1-4(a), App. 1-4(d)
32 App1-4(f) = tf/L 0.669/98.425 = 0.007
33 App1-4(f)Calc = if(AND(0.0005=<App1-4(f),App1-4(f)<0.002),"Calculation Required","Calculation not required")
34 App. 1-4(f) Calculation Not Required
35 Treq [in] = (P*L*M)/(2*S*E-0.2*P)+Corr ~~ required minimum thickness
36 (101.5*98.425*1.541)/(2*16600*0.85-0.2*101.5)+0.118 = 0.664
37 CheckTreq = Treq<=tf 0.664<=0.669 = Acceptable
38 Maximum Pressure: App. 1-4(a), App. 1-4(d)
39 Pmax [psi] = (2*S*E*nt)/(L*M+0.2*nt) ~~ maximum allowed design pressure
40 (2*16600*0.85*0.551)/(98.425*1.541+0.2*0.551) = 102.5
41 CheckPMax = Pmax >= P 102.5 >= 101.5 = Acceptable
42 App. 1-4(f) calculation is not included on this sheet
43 Nozzles may be subject to a smaller required thickness depending on location in the head.
44 Only the knuckle required thickness is calculated on this sheet
45 Heads may be subject to stress relief if large elongation occurs - UCS-79(d), UNF-79(d), UG-37(a)(1)
46 The UG-16(b) minimum thickness requirement has not been taken into consideration here.
47 This sheet cannot be used to check for allowable exterior pressure loads.
48 Use the Weld Efficiency program to calculate E
49 This sheet is for educational use only - use at your own risk.
8 Dimensions:
9 24.000 Do [in] - outside diameter of head
10 0.188 tb [in] - thickness before forming
11 0.159 tf [in] - thickness after forming
12 0.010 Corr [in] - corrosion allowance
13 Material and Conditions:
14 SA-240 304 Material
15 20,000 S [psi] - allowable stress
16 1.00 E - head longitudinal efficiency
17 50.0 P [psi] - interior pressure
18 Calculated Properties:
19 Approx. head weight based on steel, lbs = 47.4
20 Approx. head volume, cuft = 2.01
21 Variables:
22 nt [in] = tf-Corr ~~ thickness with corrosion allowance removed 0.159-0.01 = 0.149
23 L [in] = (Do-2*nt)/2 ~~ inside radius with corrosion allowance removed (24-2*0.149)/2 = 11.851
24 Ro [in]= Do/2 24/2 = 12.000
25 Required Thickness: UG-32(f)
26 Treq [in] = (P*L)/(2*S*E-0.2*P)+Corr ~~required minimum thickness
27 (50*11.851)/(2*20000*1-0.2*50)+0.01 = 0.025
28 CheckTreq = Treq<=tf 0.025<=0.159 = Acceptable
29 Maximum Pressure: UG-32(f)
30 Pmax [psi] = (2*S*E*nt)/(L+0.2*nt) ~~ maximum allowed design pressure
31 (2*20000*1*0.149)/(11.851+0.2*0.149) = 502.9
32 CheckPMax = Pmax >= P 502.9 >= 50 = Acceptable
33 App. 1-4(f) calculation is not included on this sheet
34 Heads may be subject to stress relief if large elongation occurs - UCS-79(d), UNF-79(d), UHA-44(d)
35 Use the Weld Efficiency program to calculate E
36 The UG-16(b) minimum thickness requirement has not been taken into consideration here.
37 This sheet cannot be used to check for allowable exterior pressure loads.
38 This sheet is for educational use only - use at your own risk.
8 Shell Inputs:
9 SA 516 Gr 70 Material
10 19,204 Sv [psi] - allowable stress
11 1.00 E1 - efficiency of shell at nozzle
12 47.244 Ds [in] - inside diameter of shell
13 1.180 nt [in] - nominal shell wall thickness
14 1.100 Treq [in] - required shell wall thickness
15 0.000 sca [in] - head or shell corrosion allowance
16 Nozzle Inputs:
17 SA 160Gr B Material
18 19,204 Sn [psi] - allowable stress
19 1.00 E - nozzle efficiency
20 4.488 Do [in] - outside diameter of nozzle
21 0.237 Nwall [in] - nominal wall thickness of nozzle
22 0.000 Lp [in] - exterior projection of nozzle
23 5.900 Ip [in] - interior projection of nozzle
24 0.000 nca [in] - nozzle corrosion allowance
25 12.5% UTP [%] - undertolerance allowance
26 870.2 Pn [psi] - interior pressure
27 1.180 Leg41 [in] - fillet size
28 0.000 Leg43 [in] - fillet size
29 Variables:
30 UT [in] = Nwall*UTP 0.237*0.1 = 0.030
31 Rn [in] = Do/2 - (Nwall-nca) + UT 4.488/2 - (0.237-0) + 0.03 = 2.037
32 tn [in] = Nwall-nca 0.237-0 = 0.237
33 ti [in] = Nwall-2*nca 0.237-2*0 = 0.237
34 d [in] = Do-2*tn 4.488-2*0.237 = 4.014
35 h [in] = MIN(Ip-sca,2.5*nt,2.5*ti) MIN(5.9-0,2.5*1.18,2.5*0.237) = 0.593
36 fr1 = MIN(Sn/Sv,1) MIN(19204/19204,1) = 1.000
37 fr2 = MIN(Sn/Sv,1) MIN(19204/19204,1) = 1.000
38 Required Thickness: UG-27(c)(1,2)
39 TreqN [in] = (Pn*Rn)/(Sn*E - 0.6*Pn)+nca ~~ required minimum thickness
40 (870.2*2.037)/(19204*1 - 0.6*870.2)+0 = 0.095
41 CheckTreqN = TreqN <= Nwall 0.095 <= 0.237 = Acceptable
43 Area Replacement:
44 Ar [in^2] = 1*d*Treq*1+2*tn*Treq*1*(1-fr1) ~~ required Area
45 1*4.014*1.1*1+2*0.237*1.1*1*(1-1) = 4.415
46 A1 [in^2] = max(d, 2*(nt+tn))*(E1*nt-1*Treq)-2*tn*(E1*nt-1*Treq)*(1-fr1)
47 MAX(4.014, 2*(1.18+0.237))*(1*1.18-1*1.1)-2*0.237*(1*1.18-1*1.1)*(1-1) = 0.321
48 A2 [in^2] = min((tn-trnR)*fr2*Min(5*nt,2*Lp) , (tn-trnR)*fr2*Min(5*tn,2*Lp))
49 MIN((0.237-0.095)*1*MIN(5*1.18,2*0) , (0.237-0.095)*1*MIN(5*0.237,2*0)) = 0.000
50 A3 [in^2] = Min(5*nt*ti*fr2,5*ti*ti*fr2,2*h*ti*fr2)
51 MIN(5*1.18*0.237*1,5*0.237*0.237*1,2*0.593*0.237*1) = 0.281
1 A41 [in^2] = Leg41^2*fr2 1.18^2*1 = 1.392
2 A43 [in^2] = (Leg43-nca)^2*fr2 (0-0)^2*1 = 0.000
3 Aa [in^2] = A1+A2+A3+A41+A43 ~~ actual area 0.321+0+0.281+1.392+0 = 1.994
4 CheckA = Aa >= Ar ~~ check area replacement 1.994 >= 4.415 = ERROR
5 The UG-16(b) minimum thickness requirement has not been taken into consideration here.
6 The required weld size is not checked on this sheet
7 This sheet cannot be used to check for allowable exterior pressure loads.
8 This sheet is for educational use only - use at your own risk.
8 Shell Inputs:
9 SA 516 Gr 70 Material
10 19,204 Sv [psi] - allowable stress
11 1.00 E1 - efficiency of shell at nozzle
12 47.244 Ds [in] - inside diameter of shell
13 1.180 nt [in] - nominal shell wall thickness
14 1.100 Treq [in] - required shell wall thickness
15 0.000 sca [in] - shell corrosion allowance
16 Nozzle Inputs:
17 SA - 106 Material
18 19,204 Sn [psi] - allowable stress
19 1.00 E - nozzle efficiency
20 4.488 Do [in] - outside diameter of nozzle
21 0.237 Nwall [in] - nominal wall thickness of nozzle
22 5.906 Lp [in] - exterior projection of nozzle
23 0.000 Ip [in] - interior projection of nozzle
24 0.040 nca [in] - nozzle corrosion allowance
25 12.5% UTP [%] - undertolerance allowance
26 870.2 Pn [psi] - interior pressure
27 Reinforcement:
28 SA 516 Gr 70 Material
29 19,204 Sp [psi] - allowable stress of repad
30 1.180 te [in] - repad thickness
31 7.874 Dp [in] - outside diameter
32 1.000 Leg41 [in] - fillet size
33 1.000 Leg42 [in] - fillet size
34 0.000 Leg43 [in] - fillet size
35 0.500 LegG [in] - depth of groove
36 Variables:
37 UT [in] = Nwall*UTP 0.237*0.1 = 0.030
38 Rn [in] = Do/2 - (Nwall-nca) + UT 4.488/2 - (0.237-0.04) + 0.03 = 2.077
39 ti [in] = Nwall-2*nca 0.237-2*0.04 = 0.157
40 h [in] = MIN(Ip-sca,2.5*nt,2.5*ti) MIN(0-0,2.5*1.18,2.5*0.157) = 0.000
41 tn [in] = Nwall-nca 0.237-0.04 = 0.197
42 d [in] = Do-2*tn 4.488-2*0.197 = 4.094
43 Required Thickness: UG-27(c)(1,2)
44 TreqN [in] = (Pn*Rn)/(Sn*E - 0.6*Pn)+nca ~~ required minimum thickness
45 (870.2*2.077)/(19204*1 - 0.6*870.2)+0.04 = 0.137
46 CheckTreqN = TreqN <= Nwall 0.137 <= 0.237 = Acceptable
108 Pipe Required Wall Thickness - trn from internal, trnE from external pressure
110 trn = (P*Rn)/(Sn*E - 0.6*P) <= tn-UT = (101*2.203)/(20000*1 - 0.6*101) trn =
111 trnE = (3*Do*Pa)/(4*B) <= tn-ut = (3*4.49*14.5)/(4*20000) trnE =
112
270
271
=
ling right -------->
l or Head Section
Page 1
Manual dh for hillside nozzles
Automatic Limit Diameter
Curved Shell or Head Section
t
Leg41
eg41 Shell
Vt
Rn = 2.203
UT = 0.002
t= -0.064
tn = 0.042
fr1 = 1.000
fr2 = 1.000
tc41 = -0.045
F= 1.000
0.011 Okay
0.002 Okay
-0.045 Okay
0.316 ERROR
25)+0.118)) <= 0.16-0.002
Internal External
2.085
1.043
-2.354
-2.354
-0.010
-0.013
0.000 0.000
-2.364 -2.366
(4.449) (3.409)
0 0
Do
Nt
t/2
t/2
Nozzle
Leg41
Leg41 Shell
Vt
UW-16.1 (b)
Do
Nt
t
Leg41
Leg41 Shell
Nozzle
Vt
UW-16.1 (c)
Leg41 Shell
Nozzle
Vt
UW-16.1 (c)
OD Nozzle
Nt Leg43
Full
t Penn.
Leg41
Leg41 Shell
Nozzle
Vt
Leg43
Proj
Leg5
Leg41 Shell
Nozzle
Nozzle
Shell Vt
Vt LegG
Leg43
Do
Nt Dp
t/2
t/2 L
Leg41 tp
di
Leg41 Shell
Nozzle
Vt UG-40 (a-2)
UW-16.1 (e)
Do OD Nozzle
Nt Leg43 Nt
t/2 Full Leg43
t/2 Penn.
Leg41
Leg41
Nozzle
Leg41 Shell
Leg41
Nozzle
Vt
Leg43 Vt
Ip
Shell
Nozzle
Vt
Leg43 Vt
Ip
Shell
Do
Leg43 Nt Do
Nt Leg41 t
Leg41
Leg41
Nozzle
Shell
Nozzle
Leg41
Vt
Leg43 Vt
Proj
Shell
1 2 3 4 5 6 7 8
* Light wall thicknesses are identical to stainless steel schedule 10S in sizes thru 12" and to Sch 10 in
** Standard wall thicknesses are identical to Stainless steel schedule 40S in sizes thru 12"
** Extra Strong wall thicknesses are identical to Stainless steel schedule 80S in sizes thru 12"
Undertolerance
This chart provides the under-tolerance allowance for pipes and
tubes listed in Section IIA. For example SA-53 under-tolerance
is listed as -12.5% (pipe wall can be 12.5% Thin). Use a value
of +12.5% in the Pipe spreadsheet. Undertolerance is not
used for rolled shell.
Items not included in this chart
Maximum
Wall, inch 0.125 0.625 1 2 4 7 10
0.017 0.002 0.002 0.0025 0.003
0.024 0.003 0.0025 0.003 0.0035
0.034 0.0035 0.0035 0.0035 0.004 0.006
0.057 0.004 0.004 0.0045 0.005 0.007 0.009
0.082 0.005 0.006 0.007 0.008 0.01 0.012
0.119 0.007 0.008 0.009 0.01 0.012 0.014
0.164 0.009 0.01 0.011 0.012 0.014 0.016
0.219 0.011 0.012 0.013 0.015 0.017 0.019
0.283 0.015 0.016 0.018 0.02 0.022
Factor G Charts
LDo = 1.3140312
ThisLDo = 1
NextLDo = 1.5
Range = 0.5
RatioThisLDo = 0.3719376
RatioNextLDo = 0.6280624
DoT2
DoT --> 0 4 5 6
Value 0.0959 0.0959 0.08870897 0.0706472
Next DoT 4 5 6 8
DoT = 1839.0805
ThisDoT = 1000
NextDoT = 10001
Range = 9001
RatioThisDoT = 0.9067792
RatioNextDoT = 0.0932208
ValueThis DoT = 3.315E-05
ValueNextDoT = 3.315E-05
Value for A= 3.315E-05
Do
Leg5
Nt
Leg41 Leg41
Leg41 Leg42
Shell Vt Ring te
Nozzle
g Vt
Leg43 Shell
Proj
LegG
Dp
Leg43
Weld to connect
.1 (i) modified t to reinforcing pad
Leg43
Full Do
t Penn.
Dp UW-16.1 (h)
Leg42 Nt Leg41
Ring te Leg42
UG-40 (a-2)
Nozzle
g Vt
Shell
Dp
Weld to connect
t to reinforcing pad
5 Ring te
Leg41
Nozzle
g Vt
Shell
Vt Dp
Shell
LegG
(k) UW-16.1(q)
Leg42
5 Ring te
Leg41
Nozzle
g Vt
Shell
Vt Dp
Shell
LegG
(k) UW-16.1(q)
Do
Do Nt
t Leg5
Leg41
Leg41
Leg42
Leg41
5 Ring te
Nozzle
Vt g Vt
Shell
Shell
Dp
6.1 (k) modified
LegG
UW-16.1(q) - modified
*** Nominal
X-stg 80 100 120 140 160 XX-stg Size
.147 .147 #N/A #N/A #N/A .188 .294 0.5
.154 .154 #N/A #N/A #N/A .219 .308 0.75
.179 .179 #N/A #N/A #N/A .250 .358 1
.191 .191 #N/A #N/A #N/A .250 .382 1.25
.200 .200 #N/A #N/A #N/A .281 .400 1.5
.218 .218 #N/A #N/A #N/A .344 .436 2
.276 .276 #N/A #N/A #N/A .375 .552 2.5
.300 .300 #N/A #N/A #N/A .438 .600 3
.318 .318 #N/A #N/A #N/A #N/A .636 3.5
.337 .337 #N/A .438 #N/A .531 .674 4
.375 .375 #N/A .500 #N/A .625 .750 5
.432 .432 #N/A .562 #N/A .719 .864 6
.500 .500 .594 .719 .812 .906 .875 8
.500 .594 .719 .844 1.000 1.125 1.000 10
.500 .688 .844 1.000 1.125 1.312 1.000 12
.500 .750 .938 1.094 1.250 1.406 #N/A 14
.500 .844 1.031 1.219 1.438 1.594 #N/A 16
.500 .938 1.156 1.375 1.562 1.781 #N/A 18
.500 1.031 1.281 1.500 1.750 1.969 #N/A 20
.500 1.219 1.531 1.812 2.062 2.344 #N/A 24
.500 #N/A #N/A #N/A #N/A #N/A #N/A 30
.500 #N/A #N/A #N/A #N/A #N/A #N/A 36
.500 #N/A #N/A #N/A #N/A #N/A #N/A 42
9 10 11 12 13 14 15
8 10 15 20 25 30 40 50 60
0.04889 0.0348711151 0.0185562 0.0119668 0.0085113 0.0064508 0.004165 0.0030322 0.002302
10 15 20 25 30 40 50 60 80
Do Leg43
Dp
Nt Leg41
Leg5
Leg41
tp
Leg42 di
5 Ring te
Nozzle
g Vt
Shell UG-40 (a-2) & UW-16.1(i)
Proj Dp
LegG
Leg43
g Vt
Shell
Proj Dp
LegG
Leg43
OD Nozzle
Nt
Nozzle
R
te
Shell
R/2
R/2 Vt
Dp
UG-40(i)
Nozzle
R
te
Shell
R/2
R/2 Vt
Dp
UG-40(i)
UG-42(c)
Do Shell Vt
80 100 125 150 200 250 300 400 500 600
-1.004365 -1.130182 -1.318759 -1.471083 -1.707744 -1.88941 -2.034798 -2.260428 -2.431798 -2.568636
-1.004365 -1.130182 -1.318759 -1.471083 -1.707744 -1.88941 -2.034798 -2.260428 -2.431798 -2.568636
-1.004365 -1.130182 -1.318759 -1.471083 -1.707744 -1.88941 -2.034798 -2.260428 -2.431798 -2.568636
-1.004365 -1.130182 -1.318759 -1.471083 -1.707744 -1.88941 -2.034798 -2.260428 -2.431798 -2.568636
-1.484126 -1.657577 -1.829738 -1.966576 -2.181115 -2.344862 -2.476254 -2.681937 -2.838632 -2.966576
-1.920819 -2.080399 -2.238072 -2.365523 -2.565431 -2.718967 -2.844664 -3.039054 -3.19044 -3.313364
-2.28735 -2.438899 -2.590067 -2.712198 -2.888777 -3.055024 -3.176526 -3.367543 -3.5157 -3.636388
-2.552864 -2.695772 -2.849865 -2.962083 -3.155302 -3.308646 -3.428504 -3.618436 -3.765443 -3.885903
-2.725842 -2.872895 -3.019997 -3.139063 -3.328827 -3.474955 -3.595166 -3.782516 -3.928118 -4.048662
-2.88701 -3.033019 -3.179092 -3.298119 -3.486401 -3.631384 -3.750872 -3.937552 -4.08272 -4.203099
-3.096846 -3.241526 -3.386096 -3.504802 -3.691169 -3.835079 -3.953652 -4.139541 -4.284186 -4.403737
-3.29152 -3.435061 -3.57773 -3.695312 -3.879949 -4.024145 -4.141947 -4.327353 -4.471644 -4.588544
-3.466999 -3.612833 -3.754179 -3.870633 -4.053369 -4.196403 -4.313005 -4.497837 -4.64129 -4.758164
-3.663152 -3.813275 -3.947306 -4.069663 -4.25003 -4.390215 -4.50799 -4.69017 -4.830667 -4.94992
-3.742487 -3.924837 -4.113509 -4.257275 -4.471083 -4.623423 -4.727346 -4.910569 -5.055517 -5.005243
-3.757607 -3.950146 -4.14422 -4.300185 -4.543705 -4.728323 -4.87647 -5.054531 -5.055517 -5.005243
-3.764472 -3.958607 -4.149669 -4.306731 -4.55444 -4.744835 -4.898076 -5.054531 -5.055517 -5.005243
-3.764472 -3.958607 -4.152427 -4.310691 -4.560667 -4.754487 -4.91364 -5.054531 -5.055517 -5.005243
-3.764472 -3.958607 -4.152427 -4.310691 -4.560667 -4.754487 -4.91364 -5.054531 -5.055517 -5.005243
-3.764472 -3.958607 -4.152427 -4.310691 -4.560667 -4.754487 -4.91364 -5.054531 -5.055517 -5.005243
15 16 17 18 19 20 21 22 23 24
-2.725842 -2.872895 -3.019997 -3.139063 -3.328827 -3.474955 -3.595166 -3.782516 -3.928118 -4.048662
-2.88701 -3.033019 -3.179092 -3.298119 -3.486401 -3.631384 -3.750872 -3.937552 -4.08272 -4.203099
-2.827065 -2.973463 -3.119918 -3.23896 -3.427793 -3.573202 -3.692959 -3.879889 -4.025218 -4.145658
0.001489 0.001063 0.000759 0.000577 0.000373 0.000267 0.000203 0.000132 9.44E-05 7.15E-05
Shell
Vt
-4.236572 -4.383
-4.390103 -4.536685
-4.332999 -4.479523
4.65E-05 3.31E-05