Professional Documents
Culture Documents
Manual TX Multi C
Manual TX Multi C
TECHNICAL FEATURES
Model Tx Multi C
1 Battery 2032 (3V)
Frequencies 300 - 390 MHz
3 Channels
Special Chip
How to do it?
1. Locate the selector switch at the back of your TX Multi C. Remove the cover to access the DIP switch
selectors and hidden button.
2. Select on the brand selector of your TX Multi C the 8 DIP switch combination for the brand of your
garage door opener. (See table 1).
3. Press once the learn button of your receiver to open programmation. Please check your garage door
opener’s manual to find the button.
4. Press the button of your TX Multi C you want to use.
5. Your remote is ready to be used.
Example:
If your original remote is Genie GM3T, GITR-3 or G3T-BX in 390 MHz frequency, then on your TX Multi C
you need to select the following DIP switch combination. By doing this your TX Multi C will be compatible
with these original remotes and you will be able to operate your Genie garage door opener.
GENIE
GM3T GITR-3
6 G3T-BX
390 MHz
Another example, if we do another combination, like the one below, our TX Multi C will be compatible
with Liftmaster 315 MHz (garage door operator’s orange button)
LIFTMASTER
971LM
972LM
2 973LM
974LM
Security +
390 MHz
IMPORTANT: IF YOUR GARAGE DOOR OPENER IS LIFTMASTER, PLEASE ALWAYS CHECK THE COLOR OF
YOUR GARAGE DOOR OPENER BEFORE START PROGRAMMING. DEPENDS ON THE COLOUR OF YOUR
LIFTMASTER GARAGE DOOR OPENER YOU MAY NEED ONE OR ANOTHER COMBINATION.
IN THIS CASE THE LIFTMASTER BUTTON IS ORANGE. YOU WILL FIND DIP COMBINATIONS FOR THIS KIND
OF GARAGE DOOR OPENER AT POSITION 2.
TABLE 1
Original remote
Compatible brand and
# Brand combination (and Liftmaster learn
frequency
button color)
LIFTMASTER
Lobas
TX2028
371LM
1 811 LM
971 LM
Craftman
Security+
315 MHz
LIFTMASTER
971LM
972LM
2 973LM
974LM
Security +
390 MHz
LIFTMASTER
Chamberlain
3
Lobas
390 MHZ
GENIE
4
315 MHz
GENIE
1024
5
315 MHz
Section A
GENIE
GM3T GITR-3
6 G3T-BX
390 MHz
OVERHEAD
7 109130-390
390 MHz
CLONE MODE
ATTENTION: CLONE MODE MUST BE DONE ON A TABLE. PLEASE BE AWARE THAT CLONE MODE IS ONLY
AVAILABLE FOR THE FOLLOWING BRANDS AND MODELS:
How to do it?
1. Locate the selector switch at the back of your TX Multi C. Remove the cover to access the DIP
switch selectors and hidden button.
2. Pull DIP switch number 2 and 7 up on your TX Multi C as shown below. This combination works for
all the brands.
3. Place your TX Multi C in front of your original remote separated each other between 3 to 6
centimeters
4. Press the hidden button of your TX Multi C for 2 seconds. Check that LED remains on.
5. Press the button of your TX Multi C you want to use to operate your garage door opener. Then the
LED of the TX Multi C will turn off.
6. Keep pressed the button of the original remote that works on your garage door opener. While you
do this the LED of the TX Multi C will remain on. Keep pressing the button of the original remote
until the LED of your TX Multi C starts flashing quickly. Remember some brands take longer than
others
7. Your TX Multi C is ready to be used.
ATTENTION: ONLY BUTTON NUMBER ONE WORKS IN THIS MODE. PLEASE BE AWARE THAT SEQUENTIAL
FLASH MODE IS ONLY AVAILABLE FOR THE CERTAIN BRANDS AND FREQUENCIES.
How to do it?
1. Locate the selector switch at the back of your TX Multi C. Remove the cover to access the DIP
switch selectors and hidden button.
2. Pull DIP switch number 1 and 2 up on your TX Multi C as shown below. This combination works for
all the brands.
3. Press the hidden button of your TX Multi C for 2 seconds. Check that the LED remains on.
4. Press the button of your TX Multi C that you want to use as many times as shown in table 2 for the
brand and frequency of your garage door opener. LED will flash as many times as you pressed.
IMPORTANT: wait until LED stops flashing before pressing again the button.
LIFTMASTER
315 MHZ
1 TIME
LIFTMASTER
390 MHZ
3 TIMES
LIFTMASTER
4 TIMES 390 MHZ