Professional Documents
Culture Documents
336d L Excavators M4t00001-Up (Machine) Powered by c9 Engine (Sebp5387 - 33) - Documentation
336d L Excavators M4t00001-Up (Machine) Powered by c9 Engine (Sebp5387 - 33) - Documentation
Welcome: r461ah
Product: EXCAVATOR
Model: 336D L EXCAVATOR M4T
Configuration: 336D L Excavators M4T00001-UP (MACHINE) POWERED BY C9
Engine
Special Instruction
Installation Procedure for 255-1923 Front Lines Gp {5057}
Media Number -GEHS0403-00 Publication Date -22/10/2012 Date Updated -22/10/2012
i04751894
Installation Procedure for 2551923 Front Lines Gp {5057}
SMCS 5057
Excavator:
330D (S/N: GBC1UP; GGE1UP; THJ1UP; LRM1UP; ERN1UP; RAS1UP; T2Y1UP)
336D (S/N: PTB1UP; JBF1UP; J2F1UP; LMG1UP; MYG1UP; KDJ1UP; PPN1UP; MYP1UP; JWR1UP; DTS1UP; M4T1UP; WET1UP)
Mobile Hydraulic Power Unit:
330D MHPU (S/N: GMN1UP)
Work Tool:
HYDRAULIC KIT (S/N: HKD1UP)
Introduction
This special instruction covers the installation procedure for 2551923 Front Lines Gp on the models and applications listed above.
Safety Section
Do not operate or work on this machine unless you have read and
understand the instructions and warnings in the Operation and
Maintenance Manuals. Failure to follow the instructions or heed the
warnings could result in injury or death. Contact your Cat dealer for
replacement manuals. Proper care is your responsibility.
Personal injury can result from hydraulic oil pressure and hot oil.
Hydraulic oil pressure can remain in the hydraulic system after the
engine has been stopped. Serious injury can be caused if this pressure is
not released before any service is done on the hydraulic system.
Make sure all of the work tools have been lowered to the ground, and
the oil is cool before removing any components or lines. Remove the oil
filler cap only when the engine is stopped, and the filler cap is cool
enough to touch with your bare hand.
Personal injury or death can result from improperly checking for a
leak.
Always use a board or cardboard when checking for a leak. Escaping
air or fluid under pressure, even a pinhole size leak, can penetrate body
tissue causing serious injury, and possible death.
If fluid is injected into your skin, it must be treated immediately by a
doctor familiar with this type of injury.
Illustration 1 g00104545
Prevent the machine from movement. Park the machine on a level surface.
Attach a "Do Not Operate" warning tag to the start switch before you service or repair the equipment. These warning tags (Special Instruction, SEHS7332) are available
from your Caterpillar dealer.
Required Parts
Table 1
2551923 Front Lines Gp Revision 04
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
Note: Put identification marks on all hoses, on all hose assemblies, on all harness assemblies, and on all tube assemblies for installation purposes. Plug all hose
assemblies and all tube assemblies. Plugging hoses and tubes helps to prevent fluid loss, and helps to keep contaminants from entering the system.
Illustration 3 g03310421
Valve group (A)
(4) 1772653 Relief Valve Gp
(5) 1875853 Block
(7) 2125148 Block
(11) 2607959 Bracket
(12) 2608030 Support
(21) 0998232 ORing Seal
(23) 1017404 Bolt
(26) 1488335 Connector As
(31) 1P3703 Rectangular Seal
(42) 8T4139 Bolt
(43) 8T4176 Bolt
(45) 8T4223 Hard Washer
(46) 8T4956 Bolt
(47) 8T5092 Bolt
1. Assemble valve group (A) .
Illustration 4 g03310422
Valve group (B)
(5) 1875853 Block
(10) 2551936 Block
(11) 2607959 Bracket
(13) 2608098 Support
(20) 3696858 Plug As
(31) 1P3703 Rectangular Seal
(42) 8T4139 Bolt
(45) 8T4223 Hard Washer
(47) 8T5092 Bolt
2. Assemble valve group (B) .
Illustration 5 g03310424
(3) 1411313 Hose As
(6) 2076443 Hose As
(9) 2551894 Support
(14) 2608193 Tube As
(17) 2661303 Hose As
(18) 2751384 Hose As
(24) 1083819 Bolt
(25) 1488330 Connector As
(28) 1488356 Elbow As
(29) 1536237 Elbow As
(32) 1P4578 Half Flange
(33) 2802747 Bolt
(36) 5P7470 Clip
(37) 5P7471 Clip
(38) 5P8182 Grommet
(40) 8T4121 Hard Washer
(44) 8T4196 Bolt
(45) 8T4223 Hard Washer
(46) 8T4956 Bolt
3. Install valve groups (A) and (B) .
Illustration 6 g03313763
(2) 1053477 Bolt
(16) 2661279 Flange
(19) 2751439 Block
(22) 1017401 Bolt
(27) 1488347 Elbow As
(30) 1P3702 Rectangular Seal
4. Install flange (16) and block (19) .
Illustration 7 g03313761
(2) 1053477 Bolt
(3) 1411313 Hose As
(6) 2076443 Hose As
(8) 2551892 Support
(9) 2551894 Support
(15) 2661278 Block
(16) 2661279 Flange
(17) 2661303 Hose As
(18) 2751384 Hose As
(19) 2751439 Block
(22) 1017401 Bolt
(25) 1488330 Connector As
(29) 1536237 Elbow As
(30) 1P3702 Rectangular Seal
(32) 1P4578 Half Flange
(33) 2802747 Bolt
(36) 5P7470 Clip
(37) 5P7471 Clip
(38) 5P8182 Grommet
(40) 8T4121 Hard Washer
(41) 8T4136 Bolt
(44) 8T4196 Bolt
(45) 8T4223 Hard Washer
(46) 8T4956 Bolt
5. Install hoses (3), (18), (17), and (6) .
Copyright 1993 - 2017 Caterpillar Inc. Mon Apr 17 2017 07:56:27 GMT-0500 (Hora est. Pacífico, Sudamérica)
All Rights Reserved. r461ah
Private Network For SIS Licensees.