Download as pdf or txt
Download as pdf or txt
You are on page 1of 11

Previous Screen

Welcome: r461ah
Product:  EXCAVATOR
Model:  336D L EXCAVATOR M4T
Configuration: 336D L Excavators M4T00001-UP (MACHINE) POWERED BY C9
Engine

Special Instruction 
Installation Procedure for 255-1923 Front Lines Gp {5057}
Media Number -GEHS0403-00 Publication Date -22/10/2012 Date Updated -22/10/2012

   
i04751894

Installation Procedure for 255­1923 Front Lines Gp {5057}
SMCS ­ 5057

Excavator:
330D (S/N: GBC1­UP; GGE1­UP; THJ1­UP; LRM1­UP; ERN1­UP; RAS1­UP; T2Y1­UP)
336D (S/N: PTB1­UP; JBF1­UP; J2F1­UP; LMG1­UP; MYG1­UP; KDJ1­UP; PPN1­UP; MYP1­UP; JWR1­UP; DTS1­UP; M4T1­UP; WET1­UP)
Mobile Hydraulic Power Unit:
330D MHPU (S/N: GMN1­UP)
Work Tool:
HYDRAULIC KIT (S/N: HKD1­UP)

Introduction
This special instruction covers the installation procedure for 255­1923 Front Lines Gp on the models and applications listed above.

Safety Section

Do not operate or work on this machine unless you have read and
understand the instructions and warnings in the Operation and
Maintenance Manuals. Failure to follow the instructions or heed the
warnings could result in injury or death. Contact your Cat dealer for
replacement manuals. Proper care is your responsibility.

Personal injury can result from hydraulic oil pressure and hot oil.

Hydraulic oil pressure can remain in the hydraulic system after the
engine has been stopped. Serious injury can be caused if this pressure is
not released before any service is done on the hydraulic system.

Make sure all of the work tools have been lowered to the ground, and
the oil is cool before removing any components or lines. Remove the oil
filler cap only when the engine is stopped, and the filler cap is cool
enough to touch with your bare hand.

Personal injury or death can result from improperly checking for a
leak.

Always use a board or cardboard when checking for a leak. Escaping
air or fluid under pressure, even a pin­hole size leak, can penetrate body
tissue causing serious injury, and possible death.

If fluid is injected into your skin, it must be treated immediately by a
doctor familiar with this type of injury.
Illustration 1 g00104545

Prevent the machine from movement. Park the machine on a level surface.

Attach a "Do Not Operate" warning tag to the start switch before you service or repair the equipment. These warning tags (Special Instruction, SEHS7332) are available
from your Caterpillar dealer.

Required Parts
Table 1
255­1923 Front Lines Gp Revision ­04    

Item     Qty     Part No     Description    

(1)     1     7Y­3731     Flange    

(2)     4     105­3477     Bolt    


(3)     1     141­1313     Hose As    

(4)     1     177­2653     Relief Valve Gp    

(5)     2     187­5853     Block    

(6)     1     207­6443     Hose As    

(7)     1     212­5148     Block    

(8)     1     255­1892     Support    

(9)     1     255­1894     Support    

(10)     1     255­1936     Block    

(11)     2     260­7959     Bracket    

(12)     1     260­8030     Support    

(13)     1     260­8098     Support    

(14)     1     260­8193     Tube As    

(15)     1     266­1278     Block    

(16)     1     266­1279     Flange    

(17)     1     266­1303     Hose As    

(18)     1     275­1384     Hose As    

(19)     1     275­1439     Block    

(20)     1     369­6858     Plug As    

(21)     1     099­8232     O­Ring Seal    

(22)     4     101­7401     Bolt    

(23)     4     101­7404     Bolt    

(24)     4     108­3819     Bolt    

(25)     1     148­8330     Connector As    

(26)     2     148­8335     Connector As    

(27)     1     148­8347     Elbow As    


(28)     1     148­8356     Elbow As    

(29)     1     153­6237     Elbow As    

(30)     3     1P­3702     Rectangular Seal    

(31)     3     1P­3703     Rectangular Seal    

(32)     2     1P­4578     Half Flange    

(33)     4     280­2747     Bolt    

(34)     1     4J­0522     O­Ring Seal    

(35)     1     5K­9090     O­Ring Seal    

(36)     2     5P­7470     Clip    

(37)     2     5P­7471     Clip    

(38)     2     5P­8182     Grommet    

(39)     1     6J­2680     O­Ring Seal    

(40)     6     8T­4121     Hard Washer    

(41)     2     8T­4136     Bolt    

(42)     10     8T­4139     Bolt    

(43)     4     8T­4176     Bolt    

(44)     4     8T­4196     Bolt    

(45)     30     8T­4223     Hard Washer    

(46)     8     8T­4956     Bolt    

(47)     8     8T­5092     Bolt    


Illustration 2 g03310418
255­1923 Front Lines Gp

Installation Procedure

NOTICE
Keep all parts clean from contaminants.

Contaminants may cause rapid wear and shortened component life.

NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.

Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.

Dispose of all fluids according to local regulations and mandates.

Note: Put identification marks on all hoses, on all hose assemblies, on all harness assemblies, and on all tube assemblies for installation purposes. Plug all hose
assemblies and all tube assemblies. Plugging hoses and tubes helps to prevent fluid loss, and helps to keep contaminants from entering the system.

Illustration 3 g03310421
Valve group (A)

(4) 177­2653 Relief Valve Gp

(5) 187­5853 Block
(7) 212­5148 Block

(11) 260­7959 Bracket

(12) 260­8030 Support

(21) 099­8232 O­Ring Seal

(23) 101­7404 Bolt

(26) 148­8335 Connector As

(31) 1P­3703 Rectangular Seal

(42) 8T­4139 Bolt

(43) 8T­4176 Bolt

(45) 8T­4223 Hard Washer

(46) 8T­4956 Bolt

(47) 8T­5092 Bolt

1. Assemble valve group (A) .
Illustration 4 g03310422
Valve group (B)

(5) 187­5853 Block

(10) 255­1936 Block

(11) 260­7959 Bracket

(13) 260­8098 Support

(20) 369­6858 Plug As

(31) 1P­3703 Rectangular Seal

(42) 8T­4139 Bolt

(45) 8T­4223 Hard Washer

(47) 8T­5092 Bolt

2. Assemble valve group (B) .
Illustration 5 g03310424
(3) 141­1313 Hose As

(6) 207­6443 Hose As

(9) 255­1894 Support

(14) 260­8193 Tube As

(17) 266­1303 Hose As

(18) 275­1384 Hose As

(24) 108­3819 Bolt

(25) 148­8330 Connector As

(28) 148­8356 Elbow As

(29) 153­6237 Elbow As

(32) 1P­4578 Half Flange

(33) 280­2747 Bolt
(36) 5P­7470 Clip

(37) 5P­7471 Clip

(38) 5P­8182 Grommet

(40) 8T­4121 Hard Washer

(44) 8T­4196 Bolt

(45) 8T­4223 Hard Washer

(46) 8T­4956 Bolt

3. Install valve groups (A) and (B) .

Illustration 6 g03313763
(2) 105­3477 Bolt

(16) 266­1279 Flange

(19) 275­1439 Block
(22) 101­7401 Bolt

(27) 148­8347 Elbow As

(30) 1P­3702 Rectangular Seal

4. Install flange (16) and block (19) .

Illustration 7 g03313761
(2) 105­3477 Bolt

(3) 141­1313 Hose As

(6) 207­6443 Hose As

(8) 255­1892 Support

(9) 255­1894 Support

(15) 266­1278 Block

(16) 266­1279 Flange
(17) 266­1303 Hose As

(18) 275­1384 Hose As

(19) 275­1439 Block

(22) 101­7401 Bolt

(25) 148­8330 Connector As

(29) 153­6237 Elbow As

(30) 1P­3702 Rectangular Seal

(32) 1P­4578 Half Flange

(33) 280­2747 Bolt

(36) 5P­7470 Clip

(37) 5P­7471 Clip

(38) 5P­8182 Grommet

(40) 8T­4121 Hard Washer

(41) 8T­4136 Bolt

(44) 8T­4196 Bolt

(45) 8T­4223 Hard Washer

(46) 8T­4956 Bolt

5. Install hoses (3), (18), (17), and (6) .

Copyright 1993 - 2017 Caterpillar Inc.   Mon Apr 17 2017 07:56:27 GMT-0500 (Hora est. Pacífico, Sudamérica)
All Rights Reserved. r461ah
Private Network For SIS Licensees.

You might also like