Professional Documents
Culture Documents
Service Manual: Digital Multifunctional System
Service Manual: Digital Multifunctional System
Feb TopPage
SERVICE MANUAL
CODE: 00ZAR6020/S2E
DIGITAL MULTIFUNCTIONAL
SYSTEM
AR-6020/6023
AR-6020D/6023D
AR-6020N/6023N
MODEL AR-6026N/6031N 2
CONTENTS
Parts marked with " " are important for maintaining the safety of the set. Be sure to replace these parts with
specified ones for maintaining the safety and performance of the set.
2) If there is any abnormality such as a smoke or an abnormal When dusts enter the machine, it may cause a breakdown or
smell, interrupt the job and disconnect the power plug. copy quality issues.
3) Be sure to connect the grounding wire. If an electric leakage Some machines require intake and exhaust of air.
occurs without grounding, a fire or an electric shock may result. If intake and exhaust of air are not properly performed, copy dirt
For proper machine functionality, the machine must be or a breakdown may be a result.
grounded. 8) Unstable or slant surface
4) When connecting the grounding wire, never connect it to the fol- If the machine drops or falls down, it may cause an injury or a
lowing points. breakdown.
It may cause an explosion, a fire or an electric shock. If there are optional paper desks and the copier desks specified,
- Gas tube it is recommendable to use them.
When using the optional desk, be sure to fix the adjuster and
- Lightning conductor
lock the casters.
- A water pipe or a water faucet, which is not recognized as a
grounding object by the authorities.
- Grounding wire for telephone line
!2 20 -8 62
!2
$$ !2
."
!2
!2
..
-8 #3
-8 #3
-8 %"
-8
#3
!2
$3
!2 $3
!2 20 -8 62
!2
."
!2
..
-8
#3
-8
%"
-8
#3
!2
$3
!2 $3
2 2. Option List
Model/Option AR-6020/6023 AR-6020D/6023D AR-6020N/6023N AR-6026N/6031N Note
Document AR-RP11 Reversing single pass feeder (RSPF) O O O O
Feed System MX-VR12 Document cover STD O O O
Paper Feed MX-CS12 500-sheet paper feed unit O O O STD without motor
System MX-CS13 500-sheet paper feed unit O O O O with motor
AR-DS19 Stand (Large) O O O O
Stand
AR-DS20 Stand (Small) O O O O
AR-NB7 NETWORK EXPANSION KIT O O STD *1 STD *1
Printer AR-PB10 PRINTER EXPANSION KIT X X O O
Expansion MX-EB14 EXPANSION MEMORY BOARD O O O O
MX-PK10 *2 PS EXPANSION KIT O O O O
MX-USX1 SHARPDESK 1 LICENSE kit O O O O
MX-USX5 SHARPDESK 5 LICENSE kit O O O O
Application /
MX-US10 SHARPDESK 10 LICENSE kit O O O O
Solution
MX-US50 SHARPDESK 50 LICENSE kit O O O O
MX-USA0 SHARPDESK 100 LICENSE kit O O O O
AR-6020
[2] SPECIFICATIONS Service Manual
1.Basic specifications
A.Engine Composition
AR-6020 SPECIFICATIONS 2 – 1
2 15.Feb
216x340)
216x330)
8.5x13.5
8.5x13.4
8.5x11R
Type *2
5.5x8.5
8.5x14
8.5x13
8.5x11
A5R*1
11x17
16KR
A4R
B5R
16K
A3
B4
A4
B5
A5
8K
Inch-1 Yes Yes No No No Yes Yes Yes No Yes No Yes No No No No No No No No
Inch-2 Yes No No No Yes Yes Yes Yes No Yes No Yes No No No No No No No No
Inch-3 Yes No No Yes No Yes Yes Yes No Yes No Yes No No No No No No No No
AB-1 Yes Yes No No No Yes No No No Yes Yes Yes Yes Yes Yes Yes No No No No
AB-2 Yes No No No Yes Yes No No No Yes Yes Yes Yes Yes Yes Yes No No No No
AB-3 Yes No No No Yes Yes No No No Yes Yes Yes Yes No No Yes No Yes Yes Yes
AB-4 Yes No No Yes No Yes No No No Yes Yes Yes Yes Yes Yes Yes No No No No
AB-5 Yes No Yes No No Yes No No No Yes Yes Yes Yes Yes Yes Yes No No No No
AR-6020 SPECIFICATIONS 2 – 2
2 15.Feb
AR-6020 SPECIFICATIONS 2 – 3
2 15.Feb
Output Tray It is possible to use the Multi Bypass and each paper tray.
Output Paper Size A4/A4R, B5/B5R, 16K/16KR, 8.5”x11”/8.5”x11”R
Thin paper(55-59g/m2 13-16 lb bond)
Output Paper Type Plain paper(60-105g/m2 16-28 lb bond)
Recycled paper
AR-6020 SPECIFICATIONS 2 – 4
(4) Usable Paper Size and Weight (Main Unit Output Tray, Duplex Section)
Output Section
Main Unit Output tray
Duplex Section
(Non-Offset)
11x17 Yes Yes
8.5x14 216x356mm Yes Yes
8.5x13.5 216x343mm Yes Yes
8.5x13.4 216x340 mm Yes Yes
8.5x13 216x330 mm Yes Yes
8.5x11 Yes Yes
8.5x11R Yes Yes
7.25x10.5 No Yes
7.25x10.5R No Yes
5.5x8.5 No Yes
5.5x8.5R No Yes
A3 Yes Yes
B4 Yes Yes
Paper Size A4 Yes Yes
A4R Yes Yes
B5 Yes Yes
B5R Yes Yes
A5 No Yes
A5R Yes Yes
B6R No Yes
A6R No Yes
8K Yes Yes
16K Yes Yes
16KR Yes Yes
Envelope*1 - Yes
Extra - Yes
Custom - -
Thin Paper 55-59g/m2 13-16lb bond No Yes
60-105g/m2 16-28lb bond Yes Yes
Plain Paper
Recycled Paper Yes Yes
Heavy paper 106-128g/m2 28 lb bond -32 lb bond No Yes
Paper Type Heavy paper 129-200g/m2 32 lb bond -110 lb Cover No Yes
Envelope - Yes
OHP - Yes
Label - Yes
Tab Paper - -
J.Operation panel
(1)Display Device
(2)Key
AR-6020 SPECIFICATIONS 2 – 5
2 15.Feb
*1 According to the BA, the icon of Power Saving Key can uses the key (crescent mark) to indicate.
AR-6020 SPECIFICATIONS 2 – 6
2. Copy functions
A. Copy Ratio
Item Contents
AB Series 25%*,50,70,81,86,100,115,122,141,200,400%*
Copy Ratio (Fixed)
Inch Series 25%*,50,64,77,95,100,121,129,141,200,400%*
Platen 25-400%(376 levels by 1%)
Zoom
R-SPF 50-200%(151 levels by 1%)
Preset Ratio None
Yes (25-400% for both horizontally and vertically, However, when R-
XY Zoom
SPF is used, 50-200%)
Item Contents
Exposure Mode Auto/Text/Photo
Writing: 600 x 600 dpi
Resolution Scanning: 400 (main) x 600 (sub) dpi (Photo Mode), 400 (main) x
600 (sub) dpi (AE, Text Mode)
Writing : 2 values
Gradation
Scanning: 256 gradations
Number of manual steps 5 steps (Text/Photo)
Toner Save Mode Yes (the setting is different depending on the area)
C. Copy function
Item Contents
Auto Paper Selection (APS) O
Auto Magnification Selection (AMS) O
Auto Tray Switching O
Support Mixed Original X
Stream Feeding Mode O
Memory Copy (SOPM) O
Rotation Copy O
Sort Function O *Except for Interrupt Copy
e-Sort
Group Function O
Rotation Sort O
Sky Shot Prevention X
XY Zoom O
OC O *Except for enlarged copy
Dual Page Copy
RSPF X
AB series 10mm(5, 10, 15, 20mm)
Margin Shift
Inch series 1/2 inch (1/4,1/2,3/4,1 inch)
AB series 10mm(5, 10, 15, 20mm)
Edge+Center Erase
Inch series 1/2 inch (1/4,1/2,3/4,1 inch)
B/W Reverse X
2in1 / 4 in 1 O
ID Card Copy O (can enlarge, because the ID Card Copy for all destinations.)
Off-set Print X
Preheat Function O(Terms can be specified by system setting)
Auto Power Shutoff O(Terms can be specified by system setting)
System Setting O
Duplex Copy O(Only for D-model/N-model)
O(Can be specified according to area/Settings can be changed by service
Toner Save Mode
simulation)
Account Control O(Only copy can be controlled. Number of control: 20)
AR-6020 SPECIFICATIONS 2 – 7
3. Printer function
A. Driver supported OS
USB
Twain/ Network Custom Custom
OS *1 SPLC Custom PS PPD
Button Twain/ PCL6 PCL5e
Manager
Server 2003 No CD-ROM No CD-ROM No CD-ROM CD-ROM
Server 2003x64 No CD-ROM No CD-ROM No CD-ROM CD-ROM
Server 2008 No CD-ROM No CD-ROM No CD-ROM CD-ROM
Server 2008x64 No CD-ROM No CD-ROM No CD-ROM CD-ROM
Vista CD-ROM CD-ROM CD-ROM CD-ROM No CD-ROM CD-ROM
Vistax64 CD-ROM CD-ROM CD-ROM CD-ROM No CD-ROM CD-ROM
Windows Windows7 CD-ROM CD-ROM CD-ROM CD-ROM No CD-ROM CD-ROM
Windows7x64 CD-ROM CD-ROM CD-ROM CD-ROM No CD-ROM CD-ROM
Windows8 CD-ROM CD-ROM CD-ROM CD-ROM No CD-ROM CD-ROM
Windows8x64 CD-ROM CD-ROM CD-ROM CD-ROM No CD-ROM CD-ROM
Windows8.1 CD-ROM CD-ROM CD-ROM CD-ROM No CD-ROM CD-ROM
Windows8.1 x64 CD-ROM CD-ROM CD-ROM CD-ROM No CD-ROM CD-ROM
Server 2012 x64 No CD-ROM No CD-ROM No CD-ROM CD-ROM
9 No No No No No No No
X 10.2 No No No No No No No
X 10.3 No No No No No No No
X 10.4 No No No No No CD-ROM No
Mac X 10.5 No No No No No CD-ROM No
X 10.6 No No No No No CD-ROM No
X 10.7 No No No No No CD-ROM No
X 10.8 No No No No No CD-ROM No
X 10.9 No No No No No CD-ROM No
B. PDL emulation/Font
* When NW Expansion Kit and PS Expansion Kit are expanded, Nova-Light has optional font because it supports PS3.
* IPP,HTTP, and POP support SSL, but the Russia not support SSL.
AR-6020 SPECIFICATIONS 2 – 8
D. Direct Print
(1)File Transmission Method
Communication Method Operation Method Support
1 Pull Print After access to FTP service by operation panel and select the file, the printing is performed. No
FTP
2 Push Print Send the print instruction from PC to MFP by FTP client software. Yes
It can view the data on client PC by the “send a print job” on web page, and send a print
3 WEB Page Push Print No
instruction to MFP.
Send the attached data of E-mail to MFP by client PC, the printing is performed. It can enter
4 E-mail Push Print No
the print set instruction in the body of E-mail.
USB flash Connect the USB memory to MFP, and select the data in USB memory by operation panel,
5 Pull Print No
drive the printing is performed.
Shared After access to Shared Folder by operation panel and select the file, the printing is per-
6 Pull Print No
Folder formed.
(2)File Format
File Type Extension Support
TIFF TIFF,TIF Yes*1
JPEG FIF,JPE,JPEG,JPG Yes*1
PCL PCL,PRN,TXT Yes*1
XPS XPS No
PDF PDF Yes*2
Encrypted PDF PDF No (only NULL password*2)
PS PS,PRN Yes*2
*1: Network expansion kit for S/D model and Print expansion kit is needed.
*2: PS expansion kit is needed.
E. Print Function
PCL6 PostScript3
Function Contents SPLC
compatible compatible
Bar-code Font JetCAPS BarDIMM emulation No No No
2 units of MFP is connected tandem and
writing out is performed by 2 MFP working together. Only when HDD is
Network Tandem Print No No No
installed.
Divide jobs by PC and send them to MFPs.
ROPM One RIP processing enables plural numbers of printing out. Yes Yes Yes
RIP processing shall be available during printing. And printing shall be
Multi access support No No No
available during scanning.
Paper direction setting for duplex
As for papers having front/back attribute such as letter head or punching
printing of letter head paper or
paper, Front/back side and print order shall be corrected at duplex No No No
punch paper. [Support printing on
printing.
logo paper (SEGA AOK Company)]
The administrator can distribute driver to each client by Sharp Remote
Driver Distribution Function Device Management. No No No
Or it can use MSI to download and install.
The form is downloaded to the MFP in advance and only the data
Form Overlay No No No
contents is sent, then fit them into the form by MFP to print.
Support Planet Press by Object if Lune Inc. (software which performs
Support Planet Press No No No
mapping of form (DL in advance) and variable data inside the printer.)
Support Heisei fonts No Yes No
Add support font
Support Morisawa fonts No No No
A technology developed by Apple Corps. To detect the peripherals on
Bonjour for Macintosh environment the network automatically and connect. It enables users for dynamic No Yes No
network connection with computers, peripherals and software.
Layout print Various layouts fitted to different print usage are available. Yes No No
Function that performs saddle stitch print by small amount of pages to
Perfect binding No No No
restrain adding of thickness by plural pages binding.
Support Sharp Print System Support Print in anywhere. No No No
Support WSD The Discovery function of printer Yes Yes Yes
When print image and size is coincide and different direction of paper is
indicated as the paper feed tray, the image is rotated 90 degrees
Rotation in 90 degrees function Yes Yes Yes
automatically to print. (However, direction change during job is not
available.)
Printing position of odd/even pages is adjusted. (They can be adjusted
Printing position adjustment for
separately.) No No No
odd/even pages
Value can be adjusted by the unit of mm/inch
AR-6020 SPECIFICATIONS 2 – 9
PCL6 PostScript3
Function Contents SPLC
compatible compatible
It is a function that a certain items are turned ON mandatorily, in order to
restrict the operation by user level. The target operations for restriction
are as follows;
Consideration should be taken in designing, so as to respond to
additional requests.
Print Policy Function No No No
- User authentication every time
- Forced Retention
- Forced black and white print
- Obtain the login name of Windows
- Accounting Code
Toner Save Mode Toner Save Mode (1 step) No No No
Support RET Support simulated resolution No No No
Print density adjustment Function to switch in 5 stages. Yes Yes Yes
A4/Letter
Automatic Automatic switching while output, it may not out of paper. No No No
Switching Function
AR-6020 SPECIFICATIONS 2 – 10
2 15.Feb
* For N model and S/D model while the network expansion kit was
expanded. 9. Ambient conditions
85%
Overseas 100V Overseas 200V
20/23 cpm : 220-
60%
240V 5A
Voltage 100-127V 12A
26/31 cpm : 220-
240V 8A
Frequency 50/60Hz 50/60Hz
Power code | Sharp model Fixed Type (Direct) Inlet or direct
Power Switch 1 switch 20%
AR-6020 SPECIFICATIONS 2 – 11
2 15.Feb
B. Europe
No. Name Product name Content Life Remark
20K
1 Toner cartridge(Black) MX-237GT Toner cartridge x1 Life setting by A4 6% document
23K(Toner save mode)
8.4K
2 Toner cartridge(Black) MX-238GT Toner cartridge x1 Life setting by A4 6% document
10K(Toner save mode)
20cpm/23cpm : 75K
3 Developer MX-312GV Developer x1
26cpm/31cpm : 100K
20cpm/23cpm : 75K
4 Drum KIT MX-312GR Drum x1
26cpm/31cpm : 100K
D. Asia
No. Name Product name Content Life Remark
20K
1 Toner cartridge(Black) MX-237AT Toner cartridge x1 Life setting by A4 6% document
23K(Toner save mode)
8.4K
2 Toner cartridge(Black) MX-238AT Toner cartridge x1 Life setting by A4 6% document
10K(Toner save mode)
20cpm/23cpm : 75K
3 Developer MX-312AV Developer x1
26cpm/31cpm : 100K
20cpm/23cpm : 75K
4 Drum KIT MX-312AR Drum x1
26cpm/31cpm : 100K
2
5SE ENVI
RONMENT
CONDITIONS
1 2 3 4 5 6 7 8
The lot number is of 8 digits. Each digit indicates the content as follows.
The number is printed on the right under side of the back surface of the
4EMPERATURE developer bag.
1 Alphabet
Standard environmental Temperature 20 - 25 degrees C
Indicates the production factory.
conditions Humidity 65 +/- 5%RH
2 Number
Usage environmental Temperature 10 - 35 degrees C
conditions Indicates the production year.
Humidity 20 - 85%RH
3, 4 Number
Indicates the production month.
B.Life(packed conditions) 5, 6 Number
Indicates the production day.
Photoconductor drum (36 months from the production month)
7 Hyphen
Developer, toner (24 months from the production month) 8 Number
Indicates the production lot.
1 2 3 4 5
1 Alphabet
Indicates the model conformity code. L for this model.
2 Number
Indicates the end digit of the production year.
3 Number or X, Y, Z
Indicates the month of packing.
X stands for October, Y November, and Z December.
4, 5 Number
Indicates the day of the month of packing.
AR-6020/6023/
6020D/6023D
with Network
Expansion Kit
No. Name Function/Operation
1 Toner cartridge lock release lever To replace the toner cartridge, pull out the toner cartridge while pushing on this lever.
2 Toner cartridge Contains toner.
3 Fusing unit release levers To remove the paper misfeed in the fusing unit, push down on these levers and remove the paper.
4 Roller rotating knob Rotate to remove misfeed paper.
5 Photoconductive drum Images are formed on the photoconductive drum.
6 Fusing unit paper guide Open to remove misfeed paper.
2
3
4
5
6
7
12 13 14 15 16
9 10 11 12 13
5. Sensor, switch
2
9
7
3
2
1
8
6
7
8
9
10
11
12
22 13
14
15 21
19
21 19 17 20 16
21 19
1. General
Each adjustment item in the adjustment item list is associated with a specific Job number. Perform the adjustment procedures in the sequence
of Job numbers from the smallest to the greatest.
However, there is no need to perform all the adjustment items. Perform only the necessary adjustments according to the need.
Unnecessary adjustments can be omitted. Even in this case, however, the sequence from the smallest to the greatest Job number must be
observed.
If the above precaution should be neglected, the adjustment would not complete normally or trouble may occur.
3. Details of adjustment 3) Push the developing doctor in the arrow direction, and tighten
the fixing screws of the developing doctor in the sequence of
13233.
ADJ 1 Process section 4) Check the clearance of the developing doctor. If it is within the
specified range, then fix the doctor fixing screw with screw
1-A Developing doctor gap adjustment lock.
1) Loosen the developing doctor fixing screw A. * When inserting a thickness gauge, be careful not to scratch
the developing doctor and the MG roller.
2) Insert a thickness gauge of 1.5mm to the three positions at
20mm and 150mm from the both ends of the developing doc-
tor as shown. 1-B MG roller main pole position adjustment
1) Remove the DV front cover, and put the developing tank on a
flat surface.
20mm
2) Tie a string to a needle or a pin.
150mm
3) Hold the string and bring the needle close to the MG roller hor-
izontally. (Do not use paper clip, which is too heavy to make a
correct adjustment.) (Put the developing unit horizontally for
20mm this adjustment.)
A
1 4) Do not bring the needle into contact with the MG roller, but
bring it to a position 2 or 3mm apart from the MG roller. Mark
A the point on the MG roller which is on the extension line from
DV front cover
3
the needle tip.
A 5) Measure the distance from the marking position to the top of
2 the doctor plate of the developing unit to insure that it is 18mm.
AR-6020 ADJUSTMENTS 5 – 1
If the distance is not within the specified range, loosen the fix-
ing screw A of the main pole adjustment plate, and move the
adjustment plate in the arrow direction to adjust. 1-D Grid bias voltage adjustment
NOTE: Use a digital multi-meter with an internal resistance of
10Mohm or more.
1) Execute SIM 8-2.
2
3
4
2
3
4
<SIM8-1>
Setting
LED Output mode Default
range
AUTO indicator COPY 0 - 650 400
TEXT indicator COPY-TSON 0 - 650 320
PHOTO indicator PRINTER 0 - 650 400
TEXT indicator & PHOTO
PRINTER-TSON 0 - 650 400
indicator
AR-6020 ADJUSTMENTS 5 – 2
C = 10 x R (mm)
ADJ 2 Mechanism section When the C value is increased by 10, the image loss amount is
decreased in 1mm.
NOTE: If a jam error or paper empty occurs during copying in the
adjustment by the simulation, the image data is not saved, 4) Measure the distance between the lead edge of the paper and
and therefore recopying is required. the image printing start position (H mm). Then, set the value
(A) by calculating with the following formula.
2-A Image position adjustment A4(8.5" x 11")
AR-6020 ADJUSTMENTS 5 – 3
2) Make a copy, Then use the copy output as an original to make NOTE: Before performing the 2nd print surface rear edge void
an RSPF copy again. adjustment, be sure to perform the 2nd print surface lead
3) Check the copy output. If necessary, perform the following edge position adjustment. Never reverse the sequence.
adjustment procedures <Adjustment specification>
4) Execute SIM 50-6.
Set Spec Set
Adjustment mode SIM LED
5) Set the RSPF lead edge position set value (AUTO indicator value value range
ON) so that the same image is obtained as that obtained in the AUTO
previous OC image lead edge position adjustment. +
TEXT
Rear edge void SIM 50-1
+
PHOT 1 step:
LED Adjustment mode 4mm or
O 0.1m 1 - 99
AUTO indicator Front document scan position adjustment less
m shift
TEXT indicator Back document scan position adjustment* 1st print surface SIM 50-
AUTO
PHOTO indicator Rear edge void adjustment (RSPF) rear edge void 19*
2nd print surface SIM 50-
TEXT
rear edge void 19*
2-A (3)Rear edge void adjustment
*Set to S -> D mode before execution.
NOTE: This adjustment executes the rear edge void adjustment.
<How to operate>
2-A (4)Paper off center adjustment
When the adjustment value of the paper reading position is
increased by 1, the timing of the reading start becomes faster and NOTE: This adjustment executes the copy image on the copy and
the machine reads the paper faster in 0.1mm amount. the center offset position of paper reading adjustment.
When the adjustment value of the paper reading position is <How to operate>
increased by 1, the image reading start position is shifted to the When the adjustment value is entered by the [Numeric] keys and
reverse direction. The adjustment range is from 1 to 99. press the [START] key, the setting value is saved and the machine
makes one copy. (The setting value range is from 1 to 99.)
LED Adjustment mode
When the [INTERRUPT] key is pressed, the process is interrupted
AUTO indicator 1st print surface paper reading position adjustment
TEXT indicator 2nd print surface paper reading position adjustment * and the machine goes into the sub code input standby mode. When
PHOTO indicator Rear void adjustment (RSPF) the [CA] key is pressed, the simulation is terminated.
(When the adjustment value is increased by 1, the position is
* Supported for the installed models only. Skipped for the models shifted by 0.1mm.)
without installation.
1) Set a scale as shown in the figure below. LED Adjustment mode
AUTO, 1st tray indicator Print center offset (1st tray paper feed)
A4(8.5" x 11") AUTO, 2nd tray indicator Print center offset (2nd tray paper feed)
AUTO, 3rd tray indicator Print center offset (3rd tray paper feed) *
AUTO, 4th tray indicator Print center offset (4th tray paper feed)*
AUTO, Bypass tray indicator Print center offset (Bypass tray paper feed)
TEXT, 1st tray indicator 2nd Print center offset (1st tray paper feed)
* Supported for the installed models only. Skipped for the models
without installation.
When the 2nd printer center offset is selected, the duplex setting
becomes the S-D.
Paper rear edge
When the adjustment value of the print center offset is increased,
2) Set the document size to A4 (8.5" x 11"), and make a copy at the image position is shifted to the right. When the adjustment
100%. value of the print center offset is decreased, the image position is
shifted to the left.
3) If necessary, perform the following adjustment procedure.
When the larger value is set, the black banding could be appeared
due because the machine reads the outside of the shading area.
Void amount (Standard value: 4mm or less) When printing is made with bypass tray, use A3 paper with the AB
destination or the W-letter with the Inch destination.
When the 2nd print center offset is adjusted by reading from OC
with setting the duplex as the S-D, the machine makes a copy by
Scale image reading the 2nd paper automatically after reading the 1st paper.
1) Set a test chart (UKOG-0089CSZZ) on the document table.
Paper rear edge
2) Select a paper feed port and make a copy. Compare the copy
and the test chart. If necessary, perform the following adjust-
ment procedure.
4) Execute SIM 50-1 and set the density mode to AUTO + TEXT 3) Execute SIM 50-10. After completion of warm-up, shading is
+ PHOTO (Rear edge void).The currently set adjustment value performed and the currently set off center adjustment value of
is displayed. each paper feed port is displayed.
5) Enter the set value and press the [START] key. The correction 4) Enter the set value and press the [START] key. The correction
value is stored and a copy is made. value is stored and a copy is made.
<Duplex mode adjustment> <Duplex mode adjustment>
* 1st print surface (auto duplex) rear edge void adjustment: * 2nd print surface (auto duplex) off-center adjustment:
SIM50-19 <<AUTO>> SIM50-10 (TEXT, 1st tray indicator)
*2nd print surface (auto duplex) rear edge void adjustment:
SIM50-19<<TEXT>>
*Set to S -> D mode before execution.
AR-6020 ADJUSTMENTS 5 – 4
<Adjustment specification> 2) Manually turn the mirror base drive pulley and bring No. 2/3
mirror base unit into contact with the positioning plate. At that
Set Spec Set
Adjustment mode SIM LED
value value range time, if the front frame side and the rear frame side of No. 2/3
Paper off center SIM 50- AUTO Add 1: Single: 1 - 99 mirror base unit are brought into contact with the positioning
10 + 0.1mm Center plate at the same time, the mirror base unit parallelism is
Selecte shift to R +/- proper. If one of them is in contact with the positioning plate,
d tray side. 2.0mm
perform the adjustment of next step.
ON
2nd print surface SIM 50- TEXT Reduce Duplex:
off-center 10 + 1: 0.1mm Center
1st tray shift to L +/-
side. 2.5mm
AR-6020 ADJUSTMENTS 5 – 5
7) With the scanner unit B in contact with both stoppers, fit the 4) Check the difference (distortion balance) between left-hand
edge of the scanner unit A with the right edge of the frame, and and right-hand side images distortions.
fix the scanner unit A with the fixing screw.
Lc Lc
Copy A Copy B
Ld Ld
There is no difference There is some difference
between the distortion on between the distortion on
the right and that on the left. the right and that on the left.
Lc Ld Lc Ld
If Lc = Ld, the distortion on the left is equal to that on the right.
(The distortions are balanced.)
If the above condition is satisfied, go to the procedure 6).
If not, perform the following procedures.
5) Change the height balance of the scanner rail on the front
frame side.
, ,
AR-6020 ADJUSTMENTS 5 – 6
2-D Main scanning direction (FR direction) 2-E Sub scanning direction (scanning
magnification ratio adjustment direction) distortion adjustment
This adjustment executes the main scanning direction (Front/Rear)
and sub scanning direction magnification ratio adjustments. 2-E (1)OC mode in copying
When the adjustment value is entered by the [Numeric] keys and This adjustment executes the main scanning direction (Front/Rear)
press the [START] key, the setting value is saved and the machine and sub scanning direction magnification ratio adjustments.
makes one copy. When the adjustment value is entered by the [Numeric] keys and
Switching can be made with [AUTO/TEXT/PHOTO] key, and the press the [START] key, the setting value is saved and the machine
set value of the selected mode is displayed on the number of cop- makes one copy.
ies display. Switching can be made with [AUTO/TEXT/PHOTO] key, and the
When the adjustment value is increased by 1, the printing copy is set value of the selected mode is displayed on the number of cop-
expanded in 0.1%. The adjustment range is from 1 to 99. ies display.
When the adjustment value is increased by 1, the printing copy is
LED Adjustment mode
expanded in 0.1%. The adjustment range is from 1 to 99.
TEXT indicator Main scanning direction magnification
ratio (OC/RSPF)
PHOTO indicator Sub scanning direction magnification ratio LED Adjustment mode
(OC) TEXT indicator Main scanning direction magnification
ratio (OC/RSPF)
1) Place a scale on the document table as shown in the figure PHOTO indicator Sub scanning direction magnification ratio
(OC)
below.
Before execution of this adjustment, remove the document table
glass.
1) Place a scale on the original table as shown below, and make
a normal (100%) copy.
<Adjustment specification>
Set
Mode Specification SIM Set value
range
Add 1:0.1%
Main scanning increase 4) After warm-up, shading is performed and the current set value
At normal: +/-
direction magni- SIM 48-1 Reduce 1: 1 - 99
fication ratio
1.0%
0.1% of the main scanning direction magnification ratio is displayed
decrease on the display section in 2 digits.Enter the SIM 48-1 mode.
5) Enter the set value and press the [START] key. The set value
is stored and a copy is made.Enter the SIM 48-1 mode.
<Adjustment specification>
Mode Specification SIM Set value Set range
Add 1:0.1%
Sub scanning
increase
direction mag- Normal SIM 48-1
Reduce 1: 1 - 99
nification ratio +/-1.0% (PHOTO)
0.1%
(OC mode)
decrease
AR-6020 ADJUSTMENTS 5 – 7
2-E (2)RSPF sub scanning direction 2-F Off center adjustment
magnification ratio
This adjustment executes the main scanning direction (Front/Rear) 2-F (1)OC mode
and sub scanning direction magnification ratio adjustments. This adjustment executes the paper reading off center adjustments.
When the adjustment value is entered by the [Numeric] keys and Switching can be made with [AUTO/TEXT/PHOTO] key, and the
press the [START] key, the setting value is saved and the machine set value of the selected mode is displayed on the number of cop-
makes one copy. ies display.
Switching can be made with [AUTO/TEXT] key, and the set value of When the adjustment value is increased by 1, the copy position is
the selected mode is displayed on the number of copies display. shifted to the left in 0.1mm as the reading start position is top. The
When the adjustment value is increased by 1, the printing copy is adjustment range is from 1 to 99.
expanded in 0.1%. The adjustment range is from 1 to 99.
LED Adjustment mode
LED Adjustment mode AUTO indicator OC paper reading
AUTO indicator RSPF document surface magnification ratio adjustment TEXT indicator RSPF paper reading in 1st surface
TEXT indicator RSPF document back magnification ratio adjustment PHOTO indicator RSPF paper reading in 2nd surface
Before execution of this adjustment, remove the document table * Supported for the installed models only. Skipped for the models
glass. without installation.
Before performing this adjustment, the OC mode adjustment in 1) Make a test chart as shown below and set it so that its center
copying must be completed. line is fit with the original guide center mark.
*To make a test chart, draw a line on A3 or 11" x 17" paper at
1) Place a scale on the original table as shown below, and make
the center in the paper transport direction
a normal (100%) copy to make a test chart.
Original guide
Center
Copy paper
(A3 or 17" x 11")
Original guide
Since the printed copy is used as a test chart, put the scale in
parallel with the edge lines. 2) Make a normal copy from the bypass tray, and compare the
copy and the test chart. If necessary, perform the following
2) Set the test chart on the RSPF and make a normal (100%)
adjustment procedures.
copy.
3) Enter the SIM 50-12 mode.
3) Compare the scale image and the actual image. If necessary,
perform the following adjustment procedures.
4) Enter the SIM 48-5 mode.
AR-6020 ADJUSTMENTS 5 – 8
4) After warm-up, shading is performed.The AUTO indicator
2-F (2)RSPF original off-center adjustment lights up and the current front surface sub scanning direction
This adjustment executes the paper reading off center adjustments. magnification ratio correction value is displayed in two digits on
Switching can be made with [AUTO/TEXT/PHOTO] key, and the the display section.
set value of the selected mode is displayed on the number of cop- 5) Enter the set value and press the [START] key. The set value
ies display. is stored and a copy is made.
When the adjustment value is increased by 1, the copy position is <Adjustment specification>
shifted to the left in 0.1mm as the reading start position is top. The
adjustment range is from 1 to 99. Mode Specification SIM Set value Set range
Single:
Center +/- Add 1:
LED Adjustment mode
3.0mm 0.1mm shift
AUTO indicator OC paper reading Original off (TEXT indicator) SIM to R side
TEXT indicator RSPF paper reading in 1st surface center mode 1 - 99
Duplex: 50-12 Reduce 1:
PHOTO indicator RSPF paper reading in 2nd surface (RSPF mode)
Center +/- 0.1mm shift
3.5mm to L side
* Supported for the installed models only. Skipped for the models (PHOTO indicator)
without installation.
Before performing this adjustment, be sure to check that the paper
off center is properly adjusted.
2-F (3)Mechanical off-center adjustment
In case a satisfactory result cannot be obtained by repeating the
1) Make a test chart for the center position adjustment and set it
above procedures, perform the following procedure.
on the RSPF. Draw a line on a paper in the scanning direc-
tion. * Supported for the installed models only. Skipped for the models
without installation.
Paper transport direction Before performing this adjustment, be sure to check that the paper
Front surface Back surface off center is properly adjusted.
1) Loosen the paper feed tray off-center adjustment screws (2
pcs.) at the center section of the lift plate of the paper feed tray,
and change the gear unit position in the front/rear frame direc-
tion.
2) Make a normal copy from the bypass tray, and compare the
copy and the original test chart. If necessary, perform the fol-
lowing adjustment procedures.
original copy
a
AR-6020 ADJUSTMENTS 5 – 9
<Adjustment specification>
ADJ 3 Image density adjustment Density LED Expo- Sharp Set value Density
mode sure Gray mode
level Chart
3-A Copy mode image density adjustment output
NOTE: This adjustment sets the copy density for each mode. "2" is
Auto Auto - slightly Auto
<How to operate> copied.
When this adjustment is executed, the warm-up and the shading is "3" is
performed. Then, the current setting value is displayed in 2-digits. Text Text 3 slightly Text
copied. The greater
When the adjustment value is entered by the [Numeric] keys and the set
Photo
press the [START] key, the setting value is saved and the machine "2" is value is the Photo
(Error
Photo 3 slightly greater the (Error
makes one copy. diffu-
copied. density is diffusion)
When the setting value is increased, the printing copy becomes sion)
The smaller
darker. When the setting value is decreased, the printing copy "2" is the set
Toner Auto/ Toner
- slightly
becomes lighter. save Photo value is the save
copied smaller the
With this adjustment, only the Exp3 copy can be printed. If the set-
"3" is density is.
ting value is increased, the Exp.1 and the Exp.5 copy also become Toner Text/ Toner
3 slightly
save Photo save
darker. If the setting value is decreased, the Exp.1 and the Exp.5 copied
copy also become lighter. "2" is
Photo Auto/Text/ Photo
3 slightly
When the [INTERRUPT] key is pressed, the process is interrupted (Dither) Photo (Dither)
copied
and the machine goes into the sub code input standby mode. When
the [CA] key is pressed, the simulation is terminated.
The switching of each setting and display can be made with press-
ing the [AUTO/TEXT/PHOTO] key. The adjustment range is from 1
to 99.
UKOG-0162FCZZ
AR-6020 ADJUSTMENTS 5 – 10
[6] SIMULATIONS 2. List of simulations
Main Sub
1. General Contents
code code
01 Mirror scanning operation
Perform the following procedure to enter the simulation mode.
01 02 Mirror home position sensor (MHPS) status display
"#" key Interrupt key CLEAR key ( ) Interrupt key
05 Mirror scanning operation aging
Main code [START] key Sub code [START] key
01 Reversing single pass feeder (RSPF) aging
02 RSPF sensor status display
When the CLEAR ALL key is pressed, the simulation mode is cancelled.
03 RSPF motor operation check
When the INTERRUPT key is pressed, the process is interrupted and 02
08 RSPF paper feed solenoid operation check
the screen returns to the sub code entering display.
09 RSPF reverse solenoid operation check
* After canceling the simulation mode, be sure to turn OFF/ON the
11 RSPF PS release solenoid operation check
power and check the operation.
02 Used to display the state of the sensors in the desk.
Note: If the machine is stopped by a misfeed or paper empty while in the
03 Used to check the operations of the motor in the desk.
simulation mode or adjustment, the simulation / adjustment must
07 Used to check the operations of the lift up motor in the desk.
be restarted.
04 Used to check the operations of the paper feed clutch in the
08
desk.
Used to check the operations of the paper transport clutch in
09
the desk.
01 Operation panel display check
05 02 Fusing lamp operation check
03 Copy lamp lighting check
01 Paper feed solenoid/clutch operation check
02 Resist roller solenoid/clutch operation check
06 20 Used to check the operations of the paper feed clutch.
21 Used to check the operations of the PS clutch.
22 Used to check the operations of the manual paper feed clutch.
01 Warm-up display and aging with jam
07
06 Intermittent aging
01 Developing bias output
08 02 Main charger output
06 Transfer setting and output
01 Duplex motor forward rotation check
02 Duplex motor reverse rotation check
09
04 Duplex motor RPM adjustment
05 Duplex motor switchback time adjustment
10 01 Toner motor operation
14 - Trouble cancel (except for U2)
16 - U2 trouble cancel
20 01 Maintenance counter clear
01 Maintenance cycle setting
21
02 Mini maintenance cycle setting
01 Maintenance counter display
02 Maintenance counter display
03 Jam memory display
04 Jam total counter display
05 Total counter display
06 Developing counter display
07 Mini maintenance preset display
08 RSPF counter display
09 Paper feed counter display
10 Developer counter display
14 P-ROM version display
22 15 Trouble memory display
16 Duplex print counter display
17 Copy counter display
18 Printer counter display
19 Scanner mode counter display
21 Scanner counter display
22 RSPF jam counter display
50 Developer counter display
51 Drum counter display
52 Toner counter display
53 Transfer unit counter display
54 Fusing unit counter display
05 Duplex print counter clear 01 Flash ROM program writing mode (MCU)
49
06 Paper feed counter clear 02 Flash ROM program writing mode (NNB)
14 RSPF jam total counter clear 18 Memory reverse position adjustment in duplex copy
15 Scanner mode counter clear 19 Rear edge void adjustment in duplex copy
01 Main motor operation check 51 09 Used to adjust the ON/OFF timing of the DHV voltage.
Auto developer adjustment (Initial setting of toner density when 20 Polygon motor stop operation adjustment
25 02
replacing developer) 21 1CS pick up roller adjustment.
04 Used to display the operation data of the toner supply quantity. 06 Used to adjust the RSPF width detection level.
02 Size setting 53 07 Used to set or check the RSPF width adjustment value.
03 Auditor setting 08 RSPF scanning position automatic adjustment
04 Copier duplex setting 60 01 SDRAM (image memory area) access check
05 Count mode setting 01 Used to check the operation of the LSU unit.
61
06 Destination setting 03 Used to set the laser power.
07 Machine condition check (CPM) 63 01 Shading check
08 Interrupt Copying setting 64 01 Self print
18 Toner save mode setting
30 CE mark conformity control ON/OFF
26
31 Auditor mode exclusive setup
36 Cancel of stop at maintenance life over
37 Cancel of stop at developer life over
38 Cancel of stop at drum life over
39 Memory capacity check
43 Side void amount setting
51 Copy temporary stop function setting
54 Life correction ON/OFF setting
69 Used to set the operating for toner end
30 01 Paper sensor status display
01 Developing counter clear
42
02 Developing counter clear
01 Fusing temperature setting 1
02 Fusing temperature setting 2
43
03 Fusing temperature setting 3
04 Fusing temperature setting 4
01 Used to set the process control operation.
Used to display the result data of the process control operation
09
1.
Used to display the result data of the process control operation
10
2.
Used to display the result data of the process control operation
44 11
3.
Used to display the result data of the process control operation
12
4.
Used to display the output level of the temperature and
14
humidity sensor.
34 Setting cleaning between jobs
02 Copy density adjustment (600dpi)
Copy exposure level adjustment, individual setting (Text)
10
600dpi
Copy exposure level adjustment, individual setting (Photo)
11
600dpi
Exposure mode setting
46 19 (Gamma table setting/AUTO exposure operation mode setting/
Photo image process setting)
20 RSPF exposure correction
29 Image contrast adjustment (600dpi)
30 AUTO exposure limit setting
31 Image sharpness adjustment
When the [INTERRUPT] key is pressed in the LCD check mode, the machine goes back to the sub code input
standby mode.
When the [CA] key is pressed, the simulation is terminated.
When the [START] key is pressed with all the lamps ON, the machine goes back to the key input check mode.
01 Operation panel display check
<< Key input check mode>>
When the machine goes into the key input check mode, [- - -] is displayed on the number of copies display. Every
time when a key on the operation panel is pressed, the input value is added on the number of copies display.
[- - -] [ 1] [ 2] •••.
When a key is pressed once, it is not counted again.
05 When the [START] key is pressed, the input number is added and displayed for 3 sec, and the machine goes into
the LED lighting check mode (LED all ON state). When the [INTERRUPT] key is pressed for the first time, it is
counted. When the key is pressed for the second time, the machine goes into the sub code input mode. When the
[CA] key is pressed for the first time, it is counted. When the key is pressed for the second time, the simulation is
terminated. (Note for the key input check mode).
•Press the [START] key at the end. (When the key is pressed during the process, the machine goes into the LED
lighting check mode (all ON state).).
•When two or more keys are pressed simultaneously, they are ignored.
When the [START] key is pressed, the fusing lamp turns ON for 500ms and OFF for 500ms.
The operation is repeated 5 times.
02 Fusing lamp operation check After completion of the process, the machine goes into the sub code input standby mode.
When the [INTERRUPT] key is pressed during the process, the machine goes to the sub code input standby mode.
When the [CA] key is pressed, the simulation is terminated.
When the [START] key is pressed, the copy lamp lights up for 5 sec. After completion of lighting, the machine goes
into the sub code input mode.
When the [INTERRUPT] key is pressed, the process is interrupted and the machine goes into the sub code input
03 Copy lamp lighting check
standby mode. When the [CA] key is pressed, the simulation is terminated.
When the [INTERRUPT] key is pressed during the process, the machine goes to the sub code input standby mode.
When the [CA] key is pressed, the simulation is terminated.
When the [START] key is pressed, the main motor rotates for 30 sec at the speed corresponding to the set
magnification ratio. To prevent wasting the toner, carry out the operational sequence of starting up and shutting
down of the process unit. At this moment, the polygon motor is also operated to perform the laser discharge.
01 Main motor operation check
During the operation, the sub code is displayed on the number of copies display. When the [INTERRUPT] key is
pressed, the machine stops operation and goes to the sub code input standby mode. When the [CA] key is
pressed, the simulation is terminated.
When the [START] key is pressed, the cooling fan rotates for 30 sec.
During the operation, the sub code is displayed on the number of copies display. When the [INTERRUPT] key is
02 Cooling fan operation check
pressed, the machine stops operation and goes to the sub code input standby mode. When the [CA] key is
pressed, the simulation is terminated.
When the [START] key is pressed in the sub code input state, the Paper feed clutch turns ON for 500ms and OFF
for 500ms. This operation is repeated 20 times.
06 20 Paper feed clutch operation check During the operation, the sub code is displayed on the number of copies display. When the [INTERRUPT] key is
pressed, the machine stops operation and goes to the sub code input standby mode. When the [CA] key is
pressed, the simulation is terminated.
When the [START] key is pressed in the sub code input state, the PS clutch turns ON for 500ms and OFF for
500ms. This operation is repeated 20 times.
21 PS clutch operation check During the operation, the sub code is displayed on the number of copies display. When the [INTERRUPT] key is
pressed, the machine stops operation and goes to the sub code input standby mode. When the [CA] key is
pressed, the simulation is terminated.
When the [START] key is pressed in the sub code input state, the Manual paper feed clutch turns ON for 500ms
and OFF for 500ms. This operation is repeated 20 times.
Manual paper feed clutch operation
22 During the operation, the sub code is displayed on the number of copies display. When the [INTERRUPT] key is
check
pressed, the machine stops operation and goes to the sub code input standby mode. When the [CA] key is
pressed, the simulation is terminated.
The duplex motor is driven in forward direction (in the paper exit direction) for 30 sec.
During the process, the display section displays the sub code.
Duplex motor forward rotation check
01 After completion of the process, the machine goes into the sub code input standby mode.
(Duplex model only)
When the [INTERRUPT] key is pressed, the machine goes into the sub code input standby mode.
When the [CA] key is pressed, the simulation is terminated.
The duplex motor is driven in reverse direction for 30 sec.
During the process, the display section displays the sub code.
Duplex motor reverse rotation check
02 After completion of the process, the machine goes into the sub code input standby mode.
(Duplex model only)
When the [INTERRUPT] key is pressed, the machine goes into the sub code input standby mode.
When the [CA] key is pressed, the simulation is terminated.
When any key input is made, it is displayed on the number of copies display.
When the [START] key is pressed, the set code data are acquired and stored in the EEPROM, and the machine
goes into the sub code input standby mode.
09 Duplex motor RPM adjustment When, however, the [START] key is pressed outside the set range, it is not assured.
04
(Duplex model only) Set range: 1 - 13 Default: 4
At that time, when the [INTERRUPT] key is pressed, the data are not rewritten and the machine goes into the sub
code input standby mode.
When the [CA] key is pressed, the simulation is terminated without rewriting the data.
When any key input is made, it is displayed on the number of copies display. When the [START] key is pressed, the
set code data are acquired and stored in the EEPROM, and the machine goes into the sub code input standby
mode.
Duplex motor switchback time Set range: 1 - 99 Default: 15
05 adjustment
(Duplex model only) (Change quantity 1 2msec/1Step)
At that time, when the [INTERRUPT] key is pressed, the data are not rewritten and the machine goes into the sub
code input standby mode.
When the [CA] key is pressed, the simulation is terminated without rewriting the data.
When the [INTERRUPT] key is pressed, the machine goes into the sub code input standby mode.
When the [CA] key is pressed, the simulation is terminated.
The drum counter and rotation distance and rotation number is displayed. (Three digits are displayed alternatively.)
By pressing the [AUTO/TEXT/PHOTO] key, the display of the version is changed.
LED Displayed version
AUTO indicator Drum counter
51 Drum rotation time display
TEXT indicator Rotation distance
PHOTO indicator Rotation number
When the [INTERRUPT] key is pressed, the machine goes into the sub code input standby mode.
When the [CA] key is pressed, the simulation is terminated.
The toner counter and the rotation number is displayed. (Three digits are displayed alternatively.) By pressing the
[AUTO/TEXT/PHOTO] key, the display of the version is changed.
LED Displayed version
52 Toner rotation time display AUTO indicator Toner counter
TEXT indicator Rotation number
When the [INTERRUPT] key is pressed, the machine goes into the sub code input standby mode.
When the [CA] key is pressed, the simulation is terminated.
The transfer rotation time is displayed. (Three digits are displayed alternatively.) By pressing the [AUTO/TEXT/
PHOTO] key, the display of the version is changed.
53 Transfer rotation time display
When the [INTERRUPT] key is pressed, the machine goes into the sub code input standby mode.
When the [CA] key is pressed, the simulation is terminated.
The fuser rotation time is displayed. (Three digits are displayed alternatively.) By pressing the [AUTO/TEXT/
PHOTO] key, the display of the version is changed.
54 Fuser rotation time display
When the [INTERRUPT] key is pressed, the machine goes into the sub code input standby mode.
When the [CA] key is pressed, the simulation is terminated.
01 Jam total counter clear When the [START] key is pressed, the jam total count value is reset to zero, and zero is displayed.
The trouble memory and the EEPROM trouble history data are cleared and "000" is displayed on the number of
02 Trouble memory clear copies display. When the [INTERRUPT] key is pressed, the machine goes into the sub code input standby mode.
When the [CA] key is pressed, the simulation is terminated.
When the [START] key is pressed, the SPF count value is reset to zero and displayed on the number of copies
RSPF counter clear
04 display. When the [INTERRUPT] key is pressed, the machine goes into the sub code input standby mode. When
(Only when the RSPF is installed)
the [CA] key is pressed, the simulation is terminated.
The duplex print count data is cleared, and zero is displayed on the number of copies display.
Duplex print counter clear
05 When the [INTERRUPT] key is pressed, the machine goes into the sub code input standby mode.
(Duplex model only)
When the [CA] key is pressed, the simulation is terminated.
24
The paper feed counter data of each paper feed section is cleared, and "000" is displayed on the number of copies
06 Paper feed counter clear display. When the [INTERRUPT] key is pressed, the machine goes into the sub code input standby mode. When
the [CA] key is pressed, the simulation is terminated.
When the [START] key is pressed, the drum count and the drum rotation distance and rotation number are reset to
zero, and the drum counter value “000” is displayed on the number of copies display. When the [INTERRUPT] key
07 Drum counter clear
is pressed, the machine goes into the sub code input standby mode. When the [CA] key is pressed, the simulation
is terminated.
When the [START] key is pressed, the copy count value is reset to zero and displayed on the number of copies
08 Copy counter clear display. When the [INTERRUPT] key is pressed, the machine goes into the sub code input standby mode. When
the [CA] key is pressed, the simulation is terminated.
<Procedures>
1)Turn OFF the power of the machine.
2)Open the front cover.
3)Install the DV unit and toner cartridge.
4)Turn ON the power of the machine with the cover opened.
5)Enter Sim25-02. (Entered value display section: "CH" is displayed. Start LED: OFF)
6)Close the front cover. (Entered value display section: "---" is displayed. Start LED: ON)
25 7)Press [START] key to execute Sim25-02.
When [START] key is pressed, the main motor rotates for 3 minutes to determine the toner sensor reference value
Auto developer adjustment (Initial and clear the developer rotation time as well as to clear the developer counter.
02 setting of toner density when replacing
developer) When the operation is completed normally, the ATC sensor reference value is displayed on the entered value
display section. If an error occurs, one of the following indicators is lighted.
LED Display mode
EL EL trouble
EU EU trouble
This simulation must be executed only immediately after installing developer, Do not execute this simulation for any
developer which has been used.
If the machine goes into the warm-up state before completion of this simulation, there is a possibility that toner may
be supplied to the developer during warm-up. In such a case, therefore, the developer must be replaced with new
one.
When this mode is executed, the toner adjustment value and the setting values are displayed on the number of
copies display. By pressing the [Copy ratio] key, the setting is changed in order. When the negative value is
displayed, the [Developer replacement required indicator lights.
Main Sub
Contents Details of operation
code code
When this mode is executed, the current setting values are displayed
When [START] key is pressed, the settings are written to the EEPROM and the machine goes into the sub code
input standby mode.
Code number Mode
0 Inch-1
1 Inch-2
2 Inch-3
3 AB-1
4 AB-2
5 AB-3
6 AB-4
7 AB-5
Enable/Disable setting of FC (8.5" x 13") size detection and Mexican legal size detection.
Press [Density Select] key to change over the lighting lamp, and enter the code number to set the document size
detection.
02 Size setting LED Code number Setting
AUTO indicator 0 FC detection disable
(The following set values indicated with are ignored.)
AUTO indicator 1 (Follow the setting marked with .)
26 TEXT indicator 0 Mexican legal detection disable (FC detection enable)
TEXT indicator 1 Mexican legal detection enable (FC detection disable)
Detection size when FC (8.5" x 13") and Mexican legal size documents are used.
Detection size
When the AUTO indicator is turned
Unit to be When the AUTO on: 1
Destination Document size
used indicator is When the TEXT When the TEXT
turned on: 0 indicator is indicator is
turned on: 0 turned on: 1
Mexican legal
EX Japan FC (8.5" x 13") B4 FC (8.5" x 13")
(8.5" x 13.4")
AB series
(FC) Mexican legal
B4 B4 FC (8.5" x 13")
(8.5" x 13.4")
Document RSPF
Mexican legal
FC (8.5" x 13") LG (8.5" x 14") FC (8.5" x 13")
Inch series (8.5" x 13.4")
(FC) Mexican legal
LG (8.5" x 14") LG (8.5" x 14") FC (8.5" x 13")
(8.5" x 13.4")
* When this simulation is executed, the binding margin setup is automatically set to the default
(left side).
When any key input is made, it is displayed on the number of copies display. When the [START] key is pressed, the
set code data are acquired and stored to the count mode set variable and in the EEPROM, and the machine goes
into the sub code input standby mode. However, if the [START] key is pressed outside the set range, it is not
assured. At that time, when the [INTERRUPT] key is pressed, the data is not rewritten and the machine goes into
the sub code input standby mode. When the [CA] key is pressed, the simulation is terminated without rewriting the
data.
05 Count mode setting
[*1 : Total counter / Developer counter *2 : maintenance counter]
0 (Default): *1= Double count *2 = Double count
1: *1= Single count *2 = Double count
2: *1= Double count *2 = Single count
3: *1= Single count *2 = Single count
When this simulation is executed, the current set destination code number is displayed. Enter the desired code
number of the destination and press the [START] key to set the destination.
Code number Destination
0 Japan AB series
1 Inch series
2 EX Japan AB series
3 EX Japan inch series (FC)
4 EX Japan AB series (FC) (Default)
06 Destination setting 5 China (EX Japan AB series + China paper support)
6 Taiwan (EX Japan AB series + China paper support)
A copy run can be temporarily interrupted to allow another copy job to be performed.
When this simulation is executed, the current setting of the machine is displayed on the number of copies display.
Enter the desired code number of CE mark conformity and press the [START] key to set the code number.
08 Interrupt Copying setting Code number Meaning (CPM information)
0 Interrupt Copying OFF
1 Interrupt Copying ON
* The toner save mode of the user program is also changed accordingly.
The default value depends on the destination.
When this simulation is executed, the current set code number of CE mark conformity is displayed. Enter the
desired code number of CE mark conformity and press the [START] key to set the code number.
Used to set whether the bypass tray can be used or not when the auditor mode is set to the coin vendor mode..
Code number Setting
0 Exclusive setting OFF (Manual paper feed is valid)
31 Auditor mode exclusive setup 1 Exclusive setting ON (Manual paper feed is invalid)
2 Exclusive setting OFF (Manual paper feed is valid) + A3/WLT fee
* When this is set to "Exclusive setup ON," if the auditor is set to the coin vendor mode and the default tray is set
to the bypass tray, the default tray must be reset to the 1st tray.
Used to set stop at maintenance life over.
Code number Setting
36 Cancel of stop at maintenance life over
0 Stop at maintenance life over
1 Cancel of stop at maintenance life over * Default
Main Sub
Contents Details of operation
code code
When this simulation is executed, the current set code number is displayed. Enter the desired code number and
press the [START] key to set the code number. The machine goes into the sub code input state.
When this simulation is executed, the current set code number is displayed. Enter the desired code number and
press the [START] key to set the code number.
When this simulation is executed, the current memory capacity is displayed on the number of copies display.
When the [INTERRUPT] key is pressed at that time, the machine goes into the sub code input standby mode
without rewriting the data. When the [CA] key is pressed, the simulation mode is terminated without rewriting the
data.
* When this is set to "Stop," temporary stop is made for every 250 copies in one copy job.
Setting is made whether the image correction is made according to developer consumption degree (life progress)
or not.
When this simulation is executed, the current code number is displayed on the number of copies display.
(1=ON [Correction is performed.], 0=OFF [Correction is not performed.])
Enter the code number and press [START] key, and the setting is settled and written into the EEPROM and the
machine goes into the sub code input standby mode.
Switching can be made with [AUTO/TEXT/PHOTO] key, and the set value of the selected mode is displayed on the
number of copies display..
The setting entered at that time is written into the EEPROM.
LED Setting mode Default
All OFF Correction in the AE1 life. 1
Life correction ON/OFF setting AUTO indicator Correction in the AE2 life 1
54
TEXT indicator Correction in the TEXT life 1
PHOTO indicator Correction in the PHOTO (Error diffusion) life 1
AUTO indicator & TEXT Correction in the TS AE1 life. 1
indicator
AUTO indicator & PHOTO Correction in the TS AE2 life. 1
indicator
TEXT indicator & PHOTO Correction in the TS TEXT life 1
indicator
AUTO & TEXT & PHOTO Correction in the PHOTO (Dither) life 1
indicators
This simulation used to set the operating conditions for toner end.
2 When this simulation is performed, the current code number is displayed.
Enter a code number and press [START] key to save the setting.
The developer counter data in the EEPROM is cleared and “000” is displayed on the number of copies display.
Developing counter clear (Mini
01 When the [INTERRUPT] key is pressed at that time, the machine goes into the sub code input standby mode.
,meintenance)
When the [CA] key is pressed, the simulation mode is terminated.
42
The developer counter data in the EEPROM is cleared and “000” is displayed on the number of copies display.
02 Developing counter clear When the [INTERRUPT] key is pressed at that time, the machine goes into the sub code input standby mode.
When the [CA] key is pressed, the simulation mode is terminated.
<Fusing temperature setting 1>
With the simulation executed, the current set values are displayed.
Switch the set value with [Concentration SW] key and press the [START] key. Then the machine writes the data into
EEPROM and is standing by the sub-code entry..
Display
Contents Setting Display Setup range Reference Default
lamp
1 Ready standby TH_UM set value O O Table1 A 5
2 Black-White plain paper TH_UM set value O O Table1 C 4
3 Thin paper TH_UM set value O O Table1 D 3
4 Heavy paper1 TH_UM set value O O Table1 E 6
5 Heavy paper2 TH_UM set value O O Table1 F 6
6 Label paper TH_UM set value O O Table1 G 6
7 OHP TH_UM set value O O Table1 H 6
8 Envelop 1 - 9 TH_UM set value O O Table1 I 6
9 MM prior rotation start TH_UM set value O O Table2 J 2
10 MM prior rotation end TH_EX set value O O 0 - 90 K 3
11 Warm-up complete time O O 0 - 90 L 20
*1: As the set value is increased by 1, the target temperature is increased by 5 degree C.
43 01 Fusing temperature setting 1 (See Table 1.) The temperature for the default, 4, becomes 170 degree C.
*2: As the set value is increased by 1, the target temperature is increased by 5 degree C.
(See Table 1.) The temperature for the default, 0/3, becomes 50 degree C (20 ppm)/
165 degree C (23 ppm) respectively.
*3: As the set value is increased by 1, the target temperature is increased by 5 degree C.
(See Table 1.) The temperature for the default, 6, becomes 180 degree C.
*4: As the set value is increased by 1, the target temperature is increased by 10 degree C.
(See Table 2.) The temperature for the default, 2, becomes 100 degree C.
*5: The corrected temperature to be added to the target temperature varies according to the paper
size. For details, refer to 43-04.
Table 1
No. 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
Temperature
150 155 160 165 170 175 180 185 190 195 200 205 210 215 220 225 230
(Degree C)
Table 2
No. 0 1 2 3 4 5 6 7 8
Temperature
80 90 100 110 120 130 140 150 160
(Degree C)
When the [INTERRUPT] key is pressed at that time, the machine goes into the sub code input standby mode.
When the [CA] key is pressed, the simulation mode is terminated.
Display
Contents Setting Display Setup range Reference Default
lamp
1 Alarm Stop change TH_US temperature O O Table1 M 16
2 Alarm Stop release TH_US temperature O O Table1 N 6
3 After rotating time when a job is completed O O 0 - 90 O 0
02 Fusing temperature setting 2
*1: As the setup value is increased by 1, the target temperature is increased by 5 degree C.
(See Table 1.) The temperature for the default, 16, becomes 230 degree C.
*2: As the setup value is increased by 1, the target temperature is increased by 5 degree C.
(See Table 1.) The temperature for the default, 6, becomes 180 degree C.
Table 1
No. 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
Temperature
150 155 160 165 170 175 180 185 190 195 200 205 210 215 220 225 230
(Degree C)
When the [INTERRUPT] key is pressed at that time, the machine goes into the sub code input standby mode.
When the [CA] key is pressed, the simulation mode is terminated.
<Fusing temperature setting 3>
With the simulation executed, the current setup values are displayed.
Switch the set value with [Concentration SW] key and press the [START] key. Then the machine writes the data into
EEPROM and is standing by the sub-code entry.
Display Setup
Contents Setting Display Reference Default
lamp range
43 1 Preheating TH_UM set value O O Table2 S 2
TH_UM set value when Warm-Up at 120 degree C
2 O O Table1 T 3
or below
TH_UM set value when Warm-Up at 120 degree C
3 O O Table1 Y 0
or above
Warm-Up completion time when Warm-Up at alpha
4 O O 0 - 90 AB 23
degree C or above
TH_UM set value when Warm-Up at alpha degree
5 O O Table1 AC 2
C or above
6 Threshold value alpha when applying the AB to AC. O O 50 - 90 AD 70
03 Fusing temperature setting 3
*1: As the setup value is increased by 1, the target temperature is increased by 10 degree C.
(See Table 2.) The temperature for the default, 3, becomes 110 degree C.
*2: As the setup value is increased by 1, the target temperature is increased by 5 degree C.
(See Table 1.) The temperature for the default, 2, becomes 160 degree C.
*3: As the setup value is increased by 1, the target temperature is increased by 5 degree C.
(See Table 1.) The temperature for the default, 0, becomes 150 degree C.
Table 1
No. 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
Temperature
150 155 160 165 170 175 180 185 190 195 200 205 210 215 220 225 230
(Degree C)
Table 2
No. 0 1 2 3 4 5 6 7 8
Temperature
80 90 100 110 120 130 140 150 160
(Degree C)
When the [INTERRUPT] key is pressed at that time, the machine goes into the sub code input standby mode.
When the [CA] key is pressed, the simulation mode is terminated.
Display Setup
Contents Setting Display Reference Default
lamp range
1 Ready standby TH_UM set value [L environment] O O 0 - 99 A 60
Black-White plain paper TH_UM set value [L envi-
2 O O 0 - 99 C 55
ronment]
3 Thin paper TH_UM set value [L environment] O O 0 - 99 D 55
4 Heavy paper1 TH_UM set value [L environment] O O 0 - 99 E 55
5 Heavy paper2 TH_UM set value [L environment] O O 0 - 99 F 55
6 Label paper TH_UM set value [L environment] O O 0 - 99 G 55
7 OHP TH_UM set value [L environment] O O 0 - 99 H 55
8 Envelop 1 - 9 TH_UM set value [L environment] O O 0 - 99 I 55
MM prior rotation start TH_UM set value [L environ-
9 O O 0 - 99 J 50
ment]
MM prior rotation end TH_EX set value [L environ-
10 O O 0 - 99 K 56
ment]
11 Warm-up complete time [L environment] O O 0 - 99 L 50
Alarm Stop change TH_US temperature [L environ-
12 O O 0 - 99 M 50
ment]
Alarm Stop release TH_US temperature [L environ-
13 O O 0 - 99 N 50
ment]
After rotating time when a job is completed [L envi-
43 04 Fusing temperature setting 4 14 O O 0 - 99 O 50
ronment]
15 Preheating TH_UM set value [L environment] O O 0 - 99 S 50
TH_UM set value when Warm-Up at 120 degree C
16 O O 0 - 99 V 55
or below [L environment]
TH_UM set value when Warm-Up at 120 degree C
17 O O 0 - 99 Y 55
or above [L environment]
Warm-Up completion time when Warm-Up at alpha
18 O O 0 - 99 AB 50
degree C or above [L environment]
TH_UM set value when Warm-Up at alpha degree
19 O O 0 - 99 AC 55
C or above [L environment]
Threshold value alpha when applying the AB to AC.
20 O O 30 - 70 AD 50
[L environment]
*1: As the setup value is increased by 1, the target temperature is increased by 5 degree C.
(See Table 3.) The temperature for the default, 5, becomes 5 degree C.
*2: As the setup value is increased by 1, the target temperature is increased by 5 degree C.
(See Table 3.) The temperature for the default, 3, becomes -5 degree C.
*3: Correction temperature from starting a JOB to reaching the JOB initial temperature correction no.
of sheets
*4: Correction temperature from starting a JOB to reaching the JOB latter-half temperature correction
no. of sheets
Table 3
No. 0 1 2 3 4 5 6 7 8
Temperature
-20 -15 -10 -5 0 5 10 15 20
(Degree C)
When the [INTERRUPT] key is pressed at that time, the machine goes into the sub code input standby mode.
When the [CA] key is pressed, the simulation mode is terminated.
When the [INTERRUPT] key is pressed at that time, the machine goes into the sub code input standby mode.
When the [CA] key is pressed, the simulation mode is terminated.
When this simulation is executed, the current code number is displayed on the number of copies display.
44 Switching can be made with [Copy ratio] keys.
When the negative value is displayed, the [Developer replacement required] indicator lights.
-127 -
15 Developer life correction DVB value for process unit - O 0
127
-127 -
16 Environmental correction GB value - O 0
127
-127 -
17 Environmental correction DVB value - O 0
127
18 Duplex printing correction GB value - O 0 - 255 0
19 Duplex printing correction DVB value - O 0 - 255 0
When the [INTERRUPT] key is pressed at that time, the machine goes into the sub code input standby mode.
When the [CA] key is pressed, the simulation mode is terminated.
10 Process control data display 2 7 Corrected laser power default value (CP) (TSON) - O 0 - 255 112
When the [INTERRUPT] key is pressed at that time, the machine goes into the sub code input standby mode.
When the [CA] key is pressed, the simulation mode is terminated.
When this simulation is executed, the current code number is displayed on the number of copies display.
Switching can be made with [Copy ratio] keys.
44
No. Contents Setting Display Range Default
When the [INTERRUPT] key is pressed at that time, the machine goes into the sub code input standby mode.
When the [CA] key is pressed, the simulation mode is terminated.
When this simulation is executed, the current code number is displayed on the number of copies display.
Switching can be made with [Copy ratio] keys.
When the [INTERRUPT] key is pressed at that time, the machine goes into the sub code input standby mode.
When the [CA] key is pressed, the simulation mode is terminated.
When this simulation is executed, the current code number is displayed on the number of copies display.
Switching can be made with [AUTO/TEXT/PHOTO] key, and the set value of the selected mode is displayed on the
number of copies display.
At that time, the setup content is written into the EEPROM by pressing the [START] key.
LED Setting mode Range
34 Setting cleaning between jobs AUTO indicator Cleaning interval 100 - 250 sheets (Default : 100)
TEXT indicator Cleaning time 5 - 10 sec.(Default : 5)
PHOTO indicator Temporary stop time 0 - 998msec(Default : 0 msec)
When the [INTERRUPT] key is pressed at that time, the machine goes into the sub code input standby mode.
When the [CA] key is pressed, the simulation mode is terminated
Used to set the copy density for each mode.
(Operating procedure)
When this simulation is executed, warm-up and shading are operated, and the current set value is displayed in two
digits. (Default [50])Change the set value and press the [START] key, and a copy is made according to the set
value. The greater the set value is, the darker the density is, and vise versa. In this case, only a copy at Exp. 3 can
be made.
When, however, the density is set darker, Exp.1 and Exp. 5 become darker, too.
If the dentistry is set lighter, Exp. 1 and Exp. 5 become lighter, too.
To select a desired copy mode, press the [AUTO/TEXT/PHOTO] key.
The selected copy mode set value is displayed on the copy quantity display.
02 Copy density adjustment (600dpi) (Adjustment range: 1 ~ 99)
Used to adjust the shift amount and the inclination value for each density level (1 ~ 5) when the exposure mode is
the TEXT mode (including TS)
-The shift amount is the same as the gamma (gradation), and is used to set the overall brightness.
When the shift amount is increased, the overall brightness is decreased.
46 When the shift amount is decreased, the overall brightness is increased
-The inclination value changes the gamma (gradation).
When the set value is increased, the gamma is increased to increase the contrast.
(Clearer black and white images)
When the set value is decreased, the gamma is decreased to decrease the contrast.
(Increased gradation)
* Press the [%] key to switch between the shift amount and the inclination value.
The 7-seg display shows the mode.
The initial display is "Shift.
Copy exposure level adjustment, Shift is indicated as "b" (Brightness).
10
individual setting (Text) 600dpi Inclination is indicated as "c" (Contrast).
(Example)
[b50] [%] key [c50] [%] key [b50] [%] key [c50] •••
* Select the adjustment level with the [Light and Dark] keys.
The AUTO/TEXT/PHOTO indicators displays the selected level (Exp. 1 ~ Exp. 5)
* Select TEXT or TEXT (TS) with the [AUTO/TEXT/PHOTO] key.
LED Exposure mode to be adjusted
TEXT indicators TEXT mode
TEXT indicator & PHOTO indicator TEXT (TS) mode
* Change the shift amount and the inclination value with the Numeric keys.
The set range is [1] ~ [99]. The default is [50].
Change the set value and press the [START] key, and a copy is made at the set value.
* Change the shift amount and the inclination value with the Numeric keys.
The set range is [1] ~ [99]. The default is [50].
Change the set value and press the [START] key, and a copy is made at the set value.
Used set for the following three exposure modes. Enter a code number and press the [START] key, and the entered
number is written into the EEPROM and the machine goes into the sub code entry standby mode. (When the
[AUTO/TEXT/PHOTO] key is pressed, the number is written into the EEPROM and the set item is changed.)
<<Gamma table setting>>
When this simulation is executed, the current set code number of gamma table is displayed.
* When setting the gamma table, no AUTO/TEXT/PHOTO indicators are lighted.
46 Code number Setting (Gamma table)
1 Image quality priority mode
2 Toner consumption priority mode * Default
* If this setting is changed, the set content of SIM46-30 is reset to the default.
<<AUTO exposure mode>>
When the [AUTO/TEXT/PHOTO] key is pressed in gamma table setting, the mode is changed to the AUTO
Exposure mode setting exposure operation mode setting and the current set code number of the AUTO exposure operation mode is
(Gamma table setting / AUTO exposure displayed. (Default: 0)
19
operation mode setting / PHOTO image * When setting the AUTO exposure operation mode, the AUTO indicator is lighted.
process setting)
Code number Setting (AUTO exposure operation mode)
0 Lead edge stop * Default
1 Rear time process
Used to adjust the exposure correction amount in the RSPF mode (for the OC mode).
(Operating procedure)
When this simulation is executed, the current set value is displayed.
Enter the adjustment value with the Numeric keys and press the [START] key.
The entered set value is stored and a copy is made.
RSPF exposure correction
20 When the [INTERRUPT] key is pressed, the entered value is saved and the machine goes into the sub code entry
(Only when the RSPF is installed)
standby mode. When the [CA] key is pressed, the entered value is saved and the simulation is terminated. [1] ~
[99] (Center [50])
* The greater the set value is, the darker the density is. The smaller the set value is, the lighter the density is.
* The exposure mode is TEXT fixed. The LED does not change, either.
The exposure level can not be adjusted.
Used to set the AUTO exposure and the limit value at AUTO exposure (toner save).The set range is 0 ~ 255. The
default is 196.
Change the setting and press the [START] key, and it will be written into the EEPROM and the machine will go into
the sub code input standby mode.
Switching can be made with [AUTO/TEXT/PHOTO] key, and the set value of the selected mode is written to the
EEPROM.
LED Setting mode
46 30 AUTO exposure limit setting AUTO indicator Limit value for OC scan AUTO exposure
TEXT indicator Limit value for OC scan AUTO exposure (toner save)
PHOTO indicator Limit value for RSPF scan AUTO exposure
AUTO indicator & PHOTO indicator Limit value for RSPF scan AUTO exposure (toner save)
<Remark>
When SIM26-06 (Destination setting) and SIM46-19 (Auto exposure mode) are changed, this set content of this
simulation is also changed to the default.
Used to adjust clear/shading of image for each mode.
(Operating procedure)
When this simulation is executed, warm-up and shading are performed, and the current set value is displayed in
two digits. (Default: 1)
Change the set value and press the [START] key, and a copy is made according to the set value.
Set value Image quality
0 Shading
1 Standard (Default)
2 Clear
31 Image sharpness adjustment Use the [AUTO/TEXT/PHOTO] key to select each copy mode. The code number of the selected copy mode is
displayed on the copy quantity display .
Used to adjust the magnification ratio in the main scanning direction (front/rear) and the sub scanning direction.
Enter the adjustment value with the Numeric keys and press the [START] key, and the entered value is saved a
copy is made.
Use the [AUTO/TEXT/PHOTO] key to select each copy mode. The code number of the selected copy mode is
displayed on the copy quantity display
Main scanning/sub scanning direction (When the set value is increased by 1, the magnification ratio is increased by 0.1%.)
48 01 (Adjustment range: 1 ~ 99, Default: 50)
magnification ratio adjustment
LED Adjustment mode
TEXT indicator Main scanning direction magnification ratio adjustment (OC/RSPF)
PHOTO indicator Sub scanning direction magnification ratio adjustment (OC)
(Operating procedure)
When this simulation is executed, the [AUTO], the [TEXT] and the [PHOTO] indicators light and the program is
written to the EEPROM.
Use the writing tool on the PC to write the program. During writing, the display is made as follows. After completion
of downloading, turn OFF/ON the power to reset.
Status LED
Flash ROM program writing mode Download data reception DATA NOTIFICATION indicator flashes, AUTO/TEXT/PHOTO indicator light
01 Loader function transfer AUTO/TEXT/PHOTO indicator light
(MCU)
Data delete start TEXT/PHOTO indicator light
Data write (Boot/Program PHOTO indicator lights
section)
Sum check PHOTO indicator lights
Download end AUTO/TEXT/PHOTO indicator flash
49
The program is written into the NNB by using the USB flash drive.
(Preliminary arrangement)
(1) Save the NNB download file to the root directory of the USB flash drive.
(2) Connect the USB flash drive to the USB port of the NNB.
(Operating procedure)
When this simulation is executed, the [ONLINE] key indicator and the [SCAN] key indicator light and the machine
enters the NNB download mode. The writing operation of the program is started to the NNB.
Flash ROM program writing mode
02 During writing, the display is as shown below. When upgrade of the firmware is completed, turn OFF/ON the power
(NNB)
to reset.
Status Value section
Firmware upgrading DATA NOTIFICATON LED flashes.
Firmware upgrading completed ONLINE key indicator and SCAN key indicator flash
Error status Error indicator lights.
* The mark, " ", indicates that it is supported only for the installed model, and it is skipped for non-installed
models.
Note: When printing is made with bypass tray, use A3 paper.
When the adjustment value of the print start position is increased by 1, the resist roller ON timing is delayed
and the print image is reduced by 0.1mm. When the adjustment value of the image scan start position is
increased by 1, the scan start position is shifted to the home position by 0.1mm.
[Adjustment procedure]
(1) Set the print start position (A) (AUTO indicator ON), the lead edge void amount (B) (TEXT indicator ON), and
01 Image lead edge adjustment the scan start position (C) (PHOTO indicator ON) to <1>, and make a 100% copy.
(2) Measure the image loss (R mm) of the scale. Set as C=10 x R (mm). (Example: Set to 40.)
When the value of C is increased by 10, the image loss is decreased by 1mm.
(3) Measure the distance between the paper lead edge and the image print start position.
Set as A=10 x H (mm). (Example: Set to 50.)
50 When the value of A is increased by 10, the image lead edge is shifted toward the paper lead edge by 1mm.
(Default: 50)
(4) Set the lead edge void area as B=50 (2.5mm).
When the value of B is increased by 10, the void is increased by about 1mm.
(For 25 or less, however, the void amount is zero.)
(Example)
Image loss
R=4mm
5mm
10mm
10 Paper off-center adjustment AUTO, 1st tray indicator Print center offset (1st tray paper feed) 51
AUTO, 2nd tray indicator Print center offset (2nd tray paper feed) 58
AUTO, 3rd tray indicator Print center offset (3rd tray paper feed) 55
AUTO, 4th tray indicator Print center offset (4th tray paper feed) 55
AUTO, Bypass tray indicator Print center offset (Bypass tray) 53
TEXT, 1st tray indicator 2nd print center offset (1st tray paper feed) 55
When this mode is selected, the S-D mode is automatically set.
50 Supported for the installed models only. Skipped for the models without installation.
Note: When the adjustment value is too great, the outside area of shading may be scanned, resulting in black
streaks on copy paper.
When printing is made with bypass tray, use A3 paper.
When a document is scanned in the OC mode in the back surface center off-set adjustment and printing is
made in the S-D mode, the first document is scanned and then the second document is scanned
automatically.
Used to make the document scan off-center adjustment.
(Adjustment range: 1 - 99)
* When the adjustment value is increased by 1, the print image is shifted by 0.1mm to the left when the scan
start position is put on the upper side.
Switching can be made with [AUTO/TEXT/PHOTO] key, and the set value of the selected mode is displayed on
the number of copies display.
<Adjustment item>
12 Document off-center adjustment
LED Item Default
AUTO indicator Platen document scan 56
TEXT indicator RSPF document front scan 51
(Only when the RSPF is installed)
PHOTO indicator RSPF document back scan 51
(Only when the RSPF is installed)
Printing of the front surface in the S-D mode and printing of the even pages in the D-S mode are performed as
reverse memory copying from the rear edge of the document.
When, therefore, the printing position adjustment of output image is required, perform the adjustment as follows:
The image direction in reverse memory copying is shown in the figure below. That is, when the document scan
direction is as shown with the arrow, the output image is printed from the rear edge of scanning. If, therefore, the
print edge section is shifted, set the reference chart with the reference position at the rear edge and use this
Duplex copy memory reverse position simulation to change the set value in order to adjust the print lead edge position.
adjustment Since printing is started at the print start position and performed from the last, saved data in the memory to the head
18
(Only when the RSPF is installed or in data, the lead edge position of an image is adjusted by changing the last data position saved in the memory.
the duplex mode)
Document Paper
transport transport
direction direction
Scanning lead edge Print lead edge
Lead edge void (1)
Print start position
50
When this simulation is executed, the current set value is displayed on the number of copies display.
(Adjustment range: 1 - 99, Center value: 50)
* When the set value is increased by 1, the void amount is increased by about 0.22mm.
Enter the adjustment value with the Numeric keys and press the [START] key, and the entered number is written
into the EEPROM and the machine goes into the sub code entry standby mode.
Switching can be made with [AUTO/TEXT/PHOTO] key, and the set value of the selected mode is displayed on the
number of copies display.
51 01 TC ON/OFF timing adjustment
When the [INTERRUPT] key is pressed at that time, machine goes into the sub code input standby mode. When
the [CA] key is pressed, the simulation mode is terminated.
LED Adjustment mode Default
AUTO indicator TC ON TIMING 50
TEXT indicator TC OFF TIMING 50
Supported for the installed models only. Skipped for the models without installation.
When this simulation is executed, the current set value is displayed on the number of copies display.
* Enter the adjustment value with the Numeric keys and press the [START] key, and the entered number is
written into the EEPROM and the machine goes into the sub code entry standby mode.
Switching can be made with [AUTO/TEXT/PHOTO] key, and the set value of the selected mode is displayed on the
number of copies display.
09 DHV ON/OFF timing adjustment When the [INTERRUPT] key is pressed at that time, machine goes into the sub code input standby mode. When
the [CA] key is pressed, the simulation mode is terminated.
LED Adjustment mode Default
AUTO indicator DHV ON timing 50
TEXT indicator DHV OFF timing 50
When this simulation is performed, the current setting code number is displayed. When the code number is entered
and the [START] key is pressed, the setting is changed.
Polygon motor stop operation No. Contents
20
adjustment
0 The polygon motor is stopped after the operation is finished in 30 seconds.
1 The polygon motor is stopped right after the operation is finished.
When this simulation is performed, the current setting code number is displayed. When the code number is
entered and the [START] key is pressed, the setting is changed.
No. Contents
21 1CS pick up roller adjustment
0 Only the smallest roller is activated. (ON)
1 Setting roller is activated. (ON).
When this simulation is executed, the SDRAM check is started. Fusing execution. the start LED turns OFF. If an
SDRAM (image memory area) access error occurs, the following LED turns ON. When the operation is normally completed, the START indicator is turned
check ON.
60 01 After completion of checking, press [CA] key to reboot the machine.
LED Display mode
AUTO indicator Write end error
TEXT indicator Read end error
When the [START] key is pressed, start confirming the operation of the polygon motor and the BD.
During the confirmation, the sub code is displayed. When this confirmation is finished, the result is displayed.
When the [INTERRUPT] key is pressed, the entered value is saved and the machine goes into the sub code entry
standby mode. When the [CA] key is pressed, the entered value is saved and the simulation is terminated.
LSU operation check LED Display mode
01
DATA NOTIFICATION indicator Finish completely
AUTO indicator and ERROR indicator PM error
TEXT indicator and ERROR indicator BD error
PHOTO indicator and ERROR indicator LD degradation error
When this simulation is executed, the detailed number is displayed on the ratio display and the current set value is
displayed on the number of copies display.
61 Switching can be made with [AUTO/TEXT/PHOTO] key.
Enter the adjustment value with the Numeric keys and press the [START] key, and the entered number is
written into the EEPROM.
When the [CA] key is pressed, the entered value is saved and the simulation is terminated..
AR-6020 TROUBLESHOOTING 7 – 1
2. Details of error codes and countermeasures
E7-01 Duplex model memory error/ Image EL- Auto developer adjustment trouble
data error (Over-toner abnormality)
Detail MCU
Cause Improper connection of the CCD unit flat cable F2-40 ATC sensor trouble
Dirt on the mirror, the lens, and the reference white
plate
Copy lamp lighting abnormality Detail MCU
CCD unit abnormality Cause Toner density sensor output abnormality.
MCU PWB abnormality Sensor connector and harness connection trouble.
(When occurred in the SPF scan position.) Developing unit trouble.
Improper installation of the mirror unit MCU PWB trouble.
Check & Remedy Clean the mirror, the lens, and the reference white Check & Remedy Replace the toner density sensor.
plate.
Check connection of the sensor connector and the
Check lighting and the light quantity of the copy lamp
harness.
(SIM05-03).
Check the CCD unit. Replace the developing unit.
Check the MCU PWB. Replace the MCU PWB.
E7-20 LSU laser detection error F2-64 Toner supply operation trouble
AR-6020 TROUBLESHOOTING 7 – 2
F2-70 Improper toner cartridge detection H2-00 Thermistor open trouble (Main)
Detail MCU
Cause Developing unit disconnection H2-01 Thermistor open trouble (Sub)
MCU PWB abnormality
Check & Remedy Replace the toner cartridge.
Check installation of the developing unit. Detail MCU
Use SIM16 to cancel. Cause Sub thermistor trouble
Replace the MCU PWB. MCU PWB trouble
Thermistor connector and harness connection trouble
Fusing section connector connection trouble
F3-22 Paper feed tray 2 lift operation trouble Fusing unit not installed
Check & Remedy Use SIM 5-02 to check the heater lamp blinking oper-
ation.
Detail MCU
When normally lighting.
Cause C2LUM does not turn ON within the specified time. Check the sub thermistor and its harness.
C2LUM sensor trouble. Check the sub thermistor input circuit on the MCU
Paper feed tray 2 lift unit trouble. PWB.
MCU PWB trouble. When not normally lighting.
Sensor harness and connector connection trouble Check connection of the thermistor connector and the
Check & Remedy Check the harness and the connector of C2LUD. harness.
Replace the lift-up unit. Check the lamp control circuit on the MCU
Replace the MCU PWB. PWB.
Cancel the trouble with SIM 14.
AR-6020 TROUBLESHOOTING 7 – 3
H4-00 Thermistor low temperature detection L4-01 Main motor lock trouble
L3-00 Scanner return trouble U2-04 EEPROM read/write error (serial com-
munication error)
Detail MCU
Cause Mirror unit abnormality
Detail MCU
Scanner wire disconnection
Origin detection sensor abnormality Cause EEPROM abnormality
Mirror motor harness abnormality Check and rem- Check that the EEPROM is properly set.
Check & Remedy Use SIM 1-1 to check the mirror reciprocating opera- edy Use SIM 16 to cancel the trouble.
tions. Replace the MCU PWB.
When the mirror does not return.
Check for disconnection of the scanner wire.
Check the harness and the connector between the U2-11 Counter check sum error (EEPROM)
mirror motor and the MCU PWB.
Replace the mirror unit.
Replace the MCU PWB. Detail MCU
When the mirror does feed.
Cause EEPROM abnormality
Use SIM 1-2 to check the mirror home position sen-
sor. Check & Remedy Check that the EEPROM is properly set.
Use SIM 16 to cancel the trouble.
Replace the MCU PWB.
AR-6020 TROUBLESHOOTING 7 – 4
U2-12 Adjustment value check sum error
(EEPROM)
Detail MCU
Cause EEPROM abnormality
Check & Remedy Check that the EEPROM is properly set.
Use SIM 16 to cancel the trouble.
Replace the MCU PWB.
Detail MCU
Cause Side door sensor abnormality
MCU PWB abnormality
Check & Remedy Check that all the side doors are closed.
Replace the MCU PWB.
Detail MCU
Cause Developing unit disconnection
MCU PWB abnormality
Toner cartridge is not installed.
Check & Remedy Check installation of the developing unit.
Replace the MCU PWB.
Install toner cartridge.
AR-6020 TROUBLESHOOTING 7 – 5
2 15.Feb
- SFAXNoXXX.fld
- Mainte.inf
- Usbscan.sys
Download file:***.dwl
<Note>
•The Download file(***.dwl ) and the like that are to be downloaded
should be copied, in advance, into folders that have a maintenance
program.
•When creating a folder for a maintenance tool in the PC, be sure that no
lengthy folder name is included in the path.
(Example)
Incorrect : C:\________Long Path________\V0428\Service
Correct : C:\V0428\Service
2) Connect the PC and the main body with the download cable
(USB cable).
10) Wait a few minutes until the following panel indication. “AUTO”,
“TEXT” and “PHOTO” LEDs are blink. After make sure that above
indication, turn off the MFP power and disconnect USB cable.
When the drum cartridge, the transfer unit, or the fusing unit is
replaced with a new one, the initial detection function operates after
B.Toner density initial setting
turning ON the power to reset each counter automatically. When the developer cartridge is replaced, the initial setting of the
When the machine is initialized during warming up, or when the toner density needs to be executed by SIM25-2.
simulation is executed or the machine is turned OFF and the door
is opened before the machine enters the print (copy) ready state,
the initial detection function may not operate normally. Therefore, C.Other
never execute the simulation or never operate the machine such as
Perform the following items.
turning OFF the machine power and opening the door before the
machine enters the print (copy) ready state after replacing one of - P-ROM version display (SIM22-14) (Execute according to the
the above parts and turning ON the power. necessity.)
When the counter is not automatically reset, it must be reset manu- - JAM counter reset (SIM24-01)
ally.
- Trouble memory reset (SIM24-02)
Since the maintenance counter is not automatically reset, they
must be cleared by executing SIM20-01.
AR-6020 MAINTENANCE 9 – 1
2. Maintenance timing display
A maintenance timing is displayed when each counter reaches the set value.
The relationship between the kinds of displays and the counters is shown below.
A. Maintenance counter
Print job Enable/
LED/LCD Display content Display condition
Disable
Maintenance indicator When the Sim21-1 set value is reached Disable
B. Transfer unit
Print job Enable/
Display content Display condition
Disable
------------------ Transfer unit print counter Enable
- When the counter for the transfer unit is cleared by SIM24-16, the transfer counter data and the transfer counter in EEPROM are cleared.
- "000" is displayed on the number of copies display.
C. Fusing unit
Print job Enable/
Display content Display condition
Disable
------------------ Fusing unit print counter Enable
- When the counter for the fusing unit is cleared by SIM24-17, the fuser counter data and the fuser counter in EEPROM are cleared.
- "000" is displayed on the number of copies display.
D. Drum cartridge
Print job Enable/
Display content Display condition
Disable
------------------ Drum cartridge counter Enable
- When the counter for the fusing unit is cleared by SIM24-7, the drum counter data and the drum counter in EEPROM are cleared.
- "000" is displayed on the number of copies display.
E. Developer cartridge
Print job Enable/
Display content Display condition
Disable
Developer replacement
When the set value is reached Enable
required indicator
F. Toner cartridge
Print JOB Enable/
Display content Display condition LED condition
Disable
Toner cartridge replacement Toner near end Light Enable
required indicator Toner end Flash Disable
- The flashing display of the indicator means that the toner is being supplied while the job is printed.
AR-6020 MAINTENANCE 9 – 2
3.Maintenance list
✕: Check (Clean, replace, or adjust according to necessity.) O: Clean : Replace : Adjust ✩: Lubricate
<20/23 cpm>
Unit name Part name When calling 75K 150K 225K 300K Remark
Drum periph- OPC drum -
eral Cleaning blade - -
Side seal F/R X X X - X Replace as Process frame unit every 225K.
MC unit X -
Transfer roller - O O Replace as Transfer roller unit.
Transfer gear - X - X -
Anti-static pin - X - X -
Transfer bearing - X - X -
Separation pawl unit X -
Star ring X - Replace as Process frame unit every 225K.
Process frame unit X X X X
Developing Developer X
section Toner filter X
DV blade X X X X X
Toner sensor X X X X X Check the sensor head surface.
DV side seal F/R X X X X X
Optical sec- Mirrors/Lens/CCD O O O O O
tion Table glass/SPF glass O O O O O
Scanner lamp X X X X X Air-blow the light guide bar.
Rails X X X X X
Drive belt/Drive wire X X X X X
Sensors X X X X X
OC O O O O X
LSU Dust-proof glass X X X X X
Paper feed/ Pickup roller X O O O O
Replace it every 100K or 1 year of use
transport Separation roller X O O O O
section Transport rollers X O O O O
Transport paper guide O O O O O
Torque limiter X X X X X
Gears X X X X X
Sensors X X X X X
Fusing sec- Upper heat roller - O O
tion Upper heat roller bearing - X X
Pressure roller - O O O
Pressure roller bearing - X O O Replace if necessary.
Upper separation pawl - O O
Upper cleaning pad - X X
Thermistor - O O O O
Gear -
Paper guide - O O O O
Drive section Gears - X X X X
Belts - X X O O
Filters Ozone filter - Or, replace it every 6 month use.
Paper exit Transport rollers X O O O O
section Gears X X X X X
Discharge brush X X X X X
Transport paper guides O O O O O
Sensors X X X X X
AR-6020 MAINTENANCE 9 – 3
2 15.Feb
Unit name Part name When calling 75K 150K 225K 300K Remark
Document Replacement reference:
transport Paper feed roller O O O O O Replace according to the RSPF paper feed
section counter value.
(RSPF) RSPF section roller: 100K or 1 years of use
Pickup roller O O O O O When replacing the paper feed roller, apply
grease to the paper feed shaft. (GP-
Separation roller O O O O O 501MR)
Replacement reference:
Replace according to the RSPF paper feed
Torque limiter X X X X X
counter value.
RSPF torque limiter: 400K or 2 years of use
Discharge brush X X X X X
Transportation rollers O O O O O
Sensors X X X X X
Reading plate O O O O O
Gears X X X X X
Belts X X X X X
OC mat O O O O O
Cassette Pickup roller X O O O O
paper feed Paper feed roller X O O O O Replace it every 100K or 1 year of use
section Separation roller X O O O O
Torque limiter X X X X X
Transportation rollers X O O O O
Paper guides O O O O O
Gears X X X X X Apply the grease to the necessary part.
2 <26/31 cpm>
Unit name Part name When 100K 150K 200K 300K 400K 450K Remark
calling
Drum periph- OPC drum - X X
eral Cleaning blade - X - X
Replace as Process frame unit
Side seal F/R X X X X - X X
every 300K.
MC unit X X - X
Transfer roller - O O O Replace as Transfer roller unit.
Transfer gear - X - X - X -
Anti-static pin - X - X - X -
Transfer bearing - X - X - X -
Separation pawl unit X X - X Replace as Process frame unit
Star ring X X - X every 300K.
Process frame unit X X X X X X Process unit without the drum.
Developing Developer X X X
section Toner filter X X X
DV blade X X X X X X X
Toner sensor X X X X X X X Check the sensor head surface.
DV side seal F/R X X X X X X X
Optical sec- Mirrors/Lens/CCD O O O O O O O
tion Table glass/SPF glass O O O O O O O
Scanner lamp X X X X X X X Air-blow the light guide bar.
Rails X X X X X X X
Drive belt/Drive wire X X X X X X X
Sensors X X X X X X X
OC O O O O O O O
LSU Dust-proof glass X X X X X X X
Paper feed/ Pickup roller X O O O O O O Replace it every 100K or 1 year of
transport Separation roller X O O O O O O use
section Transport rollers X O O O O O O
Transport paper guide O O O O O O O
Torque limiter X X X X X X X
Gears X X X X X X X
Sensors X X X X X X X
AR-6020 MAINTENANCE 9 – 4
2 15.Feb
2 Unit name Part name When 100K 150K 200K 300K 400K 450K Remark
calling
Fusing sec- Upper heat roller - O O O
tion Upper heat roller bearing - X X X
Pressure roller - O O O O O
Pressure roller bearing - X O X O Replace if necessary.
Upper separation pawl - O O O
Lower separation pawl - O O O O O
Upper cleaning pad - X X X
Thermistor - - O O O O O
Gear -
Paper guide - O O O O O O
Drive section Gears - X X X X X X
Belts - X X X O X X
Filters Ozone filter - X X Or, replace it every 6 month use.
Paper exit Transport rollers X O O O O O O
section Gears X X X X X X X
Discharge brush X X X X X X X
Transport paper guides O O O O O O O
Sensors X X X X X X X
Document Replacement reference:
transport Paper feed roller O O O O O O O Replace according to the RSPF
section paper feed counter value.
(RSPF) RSPF section roller: 100K or 1
Pickup roller O O O O O O O years of use
When replacing the paper feed
roller, apply grease to the paper
Separation roller O O O O O O O feed shaft. (GP-501MR)
Replacement reference:
Replace according to the RSPF
Torque limiter X X X X X X X paper feed counter value.
RSPF torque limiter: 400K or 2
years of use
Discharge brush X X X X X X X
Transportation rollers O O O O O O O
Sensors X X X X X X X
Reading plate O O O O O O O
Gears X X X X X X X
Belts X X X X X X X
OC mat O O O O O O O
Cassette Pickup roller X O O O O O O
Replace it every 100K or 1 year of
paper feed Paper feed roller X O O O O O O
use
section Separation roller X O O O O O O
Torque limiter X X X X X X X
Transportation rollers X O O O O O O
Paper guides O O O O O O O
Apply the grease to the necessary
Gears X X X X X X X
part.
AR-6020 MAINTENANCE 9 – 5
2 15.Feb
*1 This is just a reference. The printing result could be changed depending on the usage conditions.
*1: Installation of a new toner cartridge allows to display the remaining quantity.
AR-6020 MAINTENANCE 9 – 6
C.DV seal attachment procedure
(When viewed from the front) (When viewed from the front)
Clearance with the Side molt F Side molt R Clearance with the
molt edge. molt edge.
Must not be covered. Must not be covered.
0 DV Side DV Side 0
sheet F sheet R
Molt edge Molt edge
reference 0 0 0.5 reference
0.3 0.5 0.3
AR-6020 MAINTENANCE 9 – 7
2 15.Feb
Digital Copier/Printer
Service
DIGITAL
E
Market
AR-6020 Manual
MULTIFUNCTIONAL
SYSTEM
[10] DISASSEMBLY AND ASSEMBLY
1. Disassembly and Assembly table
2
Unit Parts Contents
1 Transfer unit
A. High voltage section/Duplex
2 Transfer roller
transport section
3 Duplex transport part
1 Table glass, SPF glass
2 Scanner unit
3 Drive belt, Drive wire
B. Scanner section 4 Rails
5 Mirror, Reflector, Scanner lamp
6 Lens, CCD
7 LED PWB, LED driver PWB
1 Fusing unit
2 Thermostat
3 Thermistor
4 Fusing PG
5 Lower separation pawl
C. Fusing section
6 Heater lamp
7 Cleaning felt
8 Upper separation pawl
9 Heat roller
10 Pressure roller
1 Ozone filter
2 Cooling fan
D. Paper exit section 3 Paper exit unit
4 Transport roller
5 Paper exit roller
1 MCU PWB
E. PWB section
2 Operation panel PWB
F. Optical frame unit section 1 Optical frame unit
G. LSU section 1 LSU unit
1 Main drive unit
2 Paper feed clutch
H. Tray paper feed section/Paper 3 Paper feed roller
transport section 4 Separation roller
5 PIN sensor
6 PS roller
Tray pick up roller/ Tray paper feed roller/ Tray
1
separation roller
I. Tray paper feed section/Paper 2 Tray paper feed drive unit
transport section(26/31cpm)
3 Tray transport clutch/Tray paper feed clutch
4 Tray transport roller
1 Bypass tray unit
2 Bypass tray paper feed roller
J. Bypass tray section
3 Bypass tray separation roller
4 Bypass tray paper feed clutch
1 Power unit
2 High voltage PWB
K. Power section
3 Power switch
4 Power unit fan
1 Developer
2 Toner filter unit
3 DV side sheet F/ DV side sheet R
L. Developing section 4 Developing cartridge
5 Developing doctor
6 MG roller
7 Toner sensor
1 Drum unit
2 Main charger holder unit
M. Process section
3 Cleaning blade
4 Separation pawl unit
1 Main motor
2 Tray open/close sensor
3 Tray paper empty sensor
N. Others
4 Power supply unit cooling fan (26/31 cpm)
5 LSU cooling fan (26/31 cpm)
6 Lift up motor (26/31 cpm)
(3)
(1)
(2)
(2)
(3)
(3)
(2)Transfer roller
1)Open the pawls. Remove the transfer roller unit. Then, remove
the E-ring, the TC roller collar, the transfer roller gear, the transfer
roller bearing R and the pin from the transfer roller.
(1)
(2)
(1)
* When the transfer roller unit is fixed to the right door unit, check
that the high pressure spring of the transfer roller unit fits with the
right door unit.
No. Name
1 Table glass, SPF glass
2 Scanner unit
3 Drive belt, Drive wire
4 Rails
5 Mirror, Reflector, Scanner lamp
6 Lens, CCD
7 LED PWB, LED driver PWB
2) Clean the both surfaces of the table glass, and the SPF glass.
3) Clean the reflector, the scanner lamp, and the No. 1 mirror.
4) Remove the scanner lamp, and the LED PWB. Disconnect the 2) Remove the connectors of the fusing unit.
connector from the LED PWB.
5) Remove the harness holder, and remove the flat cable from the 3) Pull the right side part of the fusing unit shown in the figure
LED driver PWB. Remove the LED driver PWB.
<20/23 cpm>
<20/23 cpm>
<26/31 cpm>
ĭ
Ĭ
Į
(3) Thermistor
Į
1) Remove the thermistor. Ĭ
<20/23 cpm>
(4) Fusing PG
1) Remove the fusing PG.
<26/31 cpm>
2) Remove the screws fixing the upper fusing PG. (7) Cleaning felt
1) Remove the fusing cleaning plate unit.
3) Remove the Front/Rear lamp fixing plates. 2) Remove the cleaning felt.
<20/23cpm>
Ĭ
ĭ
1
2
4
1
2
Ĭ
ĭ
No. Contents
1 Ozone filter
2 Cooling fan
3 Paper exit unit
4 Transport roller
5 Paper exit roller
3) Disconnect the harness and remove the cooling fan with the
fan duct.
D/N model
5) Disconnect the harness of the LSU unit and the clamps. (1) Main drive unit
1) Remove the flywheel.
6) Remove the screws fixing the LSU unit. Then, remove the LSU
unit.
<S model>
2) Remove the E-rings, the spacers and the shaft with the pin.
Then, remove the paper feed clutch.
2) Open the right door and remove the PS right bottom guide PG.
(5) PIN sensor 3) Open the front door and remove the PS knob.
1) Remove the tray
2) Remove the PIN sensor detection lever.
3) Remove the harness, then, remove the PIN sensor. 4) Remove the left E-ring.
2) Remove the tray pick up roller, the tray paper feed roller and
the tray separation roller.
2 (4) Tray transport roller (2) Bypass tray paper feed roller
1) Remove the tray transport clutch, the tray paper feed clutch 1) Remove the service cover.
and the gears.
2) Remove the resin E-ring, and remove the bypass tray paper
feed roller.
Ĭ ĭ
K. Power section
No. Contents
1 High voltage PWB
2 Power unit
3 Power switch
4 Power unit fan
(3) Power switch 2) Remove the harness of developer cartridge from the developer
1) Remove the harnesses to the power switch with pressing the cover.
harnesses inside.
2
L. Developing section
No. Contents
1 Developer
2 Toner filter unit
3 DV side sheet F/ DV side sheet R
4 Developing cartridge
4) Check that two hooks of the developer cover is hooked on the
5 Developing doctor
toner cartridge guide, and secure the toner cartridge guide to
6 MG roller
the developing unit. Then, tighten up the screws of the devel-
7 Toner sensor oper cover.
(1) Developer
1) Remove the cartridge guide unit.
Hook
2 5) Connect the harness of developer cartridge to the developer 2) By following the figure in below, attach the DV side sheets.
cover. <DV side sheets attachment reference>
(When viewed from the front) (When viewed from the front)
Clearance with the Side molt F Side molt R Clearance with the
molt edge. molt edge.
Must not be covered. Must not be covered.
-OLT
-OLT
EDGE EDGE
REFERENCE REFERENCE
(3)
0ROJECTION EDGE 0ROJECTION EDGE
(3) REFERENCE REFERENCE
2) After removing the OPC drum, apply stearic acid powder (3) Cleaning blade
(UKOG-0312FCZZ) to the whole surface of the OPC drum. 1) Remove the cleaning blade.
3) After attaching the OPC drum to the OPC drum frame, use the
black protect sheet or copy paper, and manually rotate the
OPC drum two turns in the forward direction to remove stearic
acid powder applied to the OPC drum surface.
Press
- Do not touch the OPC drum surface except for the both ends
(5mm) of the OPC drum.
- Any section of the OPC drum may be touched from above the
black protect sheet, but do not touch too strongly.
(2) Main charger holder unit
2
1) Remove the main charger holder unit.
<26/31 cpm>
2) Remove the harness of the main motor, and remove the main
motor.
2
(1)
(2)
2 2) Remove the screws fixing the paper exit tray. 6) Remove the connector of the harness and screws of the DV
cooling duct unit. Then, remove the DV cooling duct.
1.Operation panel
A.Mechanism relation diagram
LCD
OPE PWB
B.Operational descriptions
The operation panel of this model is structured the monochrom
LCD with OPE PWB and operation keys. Because of the touch
panel function is not equipped; the operation is executed by key on
the operation panel.
And also, the adjustment of LCD brightness by hardware (volume
and so on) is not equipped.
SCOV
SPFM
SPPD2
SRRC
12 SPRS
3
1
SPUC
11
4 13
2 SPPD1 SPPD3 SPPD4
5
SPWS
SOCD
6 8 SPLS1
10 9 SPLS2
7
RSPF unit
SPLS1
SPLS2
16) After discharge (First sheet), the reverse follower roller pres-
sure is released.
13) After turning ON the PS clutch, the reverse follower roller pres-
sure is released.
MHPOS
4 7
MIRM
6
2
7 3
6
B
the reflected image is scanned by the 4-line (RGB+BW) CCD
G
elements to be converted into analog image signals.
R
2) The analog image signals are converted into 10-bit digital sig-
nals by the A/D converter.
3) The digital image signals are sent to the MCU PWB for image
processing.
R
(2)Detailed descriptions
G
B
a. Optical section drive
BW
The optical section is driven as follows: The drive power is transmit-
(Image data for 1 line)
ted from the scanner motor (MIRM) through the belt to the drive
pulley/wire, and the copy lamp unit and the mirror base which are
attached to the wire are driven.
The scanner motor (MIRM) is controlled with the signals sent from R G B
Red component Green component Blue component
the MCU PWB. image data image data image data
##$ %LEMENTS
MM
MPFC
MPED
1
2
B. Operational descriptions
Only the top sheet of paper is fed from the paper stack on the man-
ual bypass tray, the feed roller is pressed against the paper surface
and sent to the transport section.
The feed roller transports paper to registration section. Against the
paper, by applying a force in the direction opposite to the feed roller
from below, separation rollers are prevented double feeding of the
paper. On / OFF control of the feed roller is carried out by the Man-
ual Feed Clutch
This model does not have an automatic paper size detection func-
tion in Multi-purpose tray.
MM
RRC
MPWD
2
PIN
B. Operational description
The resist roller set controls the synchronization of the Image on
the Transfer Belt to the Timing of the paper making its way to the
Primary and Secondary Transfer section. Start stop movement is
controlled by the PS Clutch. Drive for the Registration roller comes
from Main motor.
MM
C1PUC
C1PED
1
2
2 B. 26/31 cpm
(1)Mechanism relation diagram
MM
C1PUC
C1LUD
C1PED C1LUM
2
3
5
MM
1
POD
4 ADUM
ADUM
B. Operational description
This is only for the D model.
The switched back paper which comes from paper exit section
goes to ADU section. The paper feed rollers are driven by the
duplex motor transporting the paper to the registration section
MM
8 5
2
2
3
6
1
7
4
Screen grid
CTL Residual toner removed from the OPC drum surface is trans-
CGL ported to the waste toner box section in the toner cartridge by
the waste toner transport screw.
Aluminum
layer OPC drum 4) The whole surface of the OPC drum is discharged.
The main charger grid is provided with the screen grid. The Laser beam
OPC drum is charged at a voltage virtually same as the volt-
age applied to the screen grid.
2) LED lights are radiated to the OPC drum surface by the laser CLT CLT
CGL CGL
unit to form latent electrostatic images. layer layer
Aluminum Aluminum
Laser beam
After completion of the job, laser beams are radiated onto al
the surface of the OPC drum.
When laser beams are radiated onto the CGL of the OPC
drum, positive and negative charges are generated.
Positive charges generated in CGL are attracted to the nega-
OPC drum tive charges on the OPC drum surface. On the other hand,
OPC drum negative charges are attracted to positive charges in the alumi-
CTL
CGL num layer of the OPC drum.
layer Therefore, positive and negative charges are balanced out on
Aluminum the OPC drum surface and in the aluminum layer, reducing
positive and negative charged to decrease the surface voltage
When LED lights are radiated to the OPC drum CGL, negative
of the OPC drum.
and positive charges are generated.
Positive charges generated in CGL are attracted to the nega-
tive charges on the OPC drum surface. On the other hand,
negative charges are attracted to positive charges in the alumi-
num layer of the OPC drum.
Therefore, positive charges and negative charges are bal-
anced out on the OPC drum and in the aluminum layer, reduc-
ing positive and negative charges to decrease the OPC drum
surface voltage.
Electric charges remain at a position where laser beam are not
radiated.
As a result, latent electrostatic images are formed on the OPC
drum surface.
TNM
B.Operational descriptions
The toner transport screw in the toner cartridge is driven by the toner motor to supply toner to the developing unit.
The toner transport screw in the toner cartridge is turned ON/OFF by the toner motor. The toner density in the developing unit is detected by
the toner density sensor. When the density falls below the specified level, the toner motor is turned ON to supply toner in the toner cartridge to
the developing unit. When the toner density reaches the specified level, the toner motor turns OFF to stop supply of toner to the developing
unit. With the above process, the toner density in the developing unit is maintained at a fixed level.
MM
TCS
2
2
layer
Aluminum CGL
CTL
Drum
-400V
MM
5
4
3
2 B. Transfer operation
The toner image on the photo conductor is transferred to the paper
by applying the positive high voltage to the transfer roller.
0HOTO CONDUCTOR /0# DRUM
$ISCHARGE PLATE
4RANSFER ROLLER
4RANSFER MODE #LEANING MODE
#ONSTANT CURRENT
C. Cleaning operation
The unnecessary toner on the transfer roller is moved to the photo
conductor by changing the polar character of the transfer roller to
the negative high voltage type. Then, the unnecessary toner is
transported to the waste toner section by the cleaning blade of the
photo conductor.
0HOTO CONDUCTOR /0# DRUM
$ISCHARGE PLATE
4RANSFER ROLLER
4RANSFER MODE #LEANING MODE
#ONSTANT CURRENT
MM
TH_MY
TH_US
TS_UM
2
1
2
4
HL_PR 2 3
HLout
Heat Roller
Pressure Roller
The heater lamp is in the heat roller, which heats the heat roller to
fuse toner onto paper.
The pressure roller is made of silicon rubber because of the follow-
ing reasons and purpose.
1) Paper is separated. (Since the heat roller is of higher hard-
ness, the pressure roller is deformed to separate paper toward
the heat roller.)
2) The nip quantity is increased to increase heat capacity for
paper.
3) By pressing paper with the flexible roller, toner is fused without
deformation.
2 B. 26/31 cpm
(1) Mechanism relation diagram
MM
TH_MY
TH_US
TS_UM 2
1
2
TS_UM
2 3
HL_PR 3
2
HLout
1. General
The following functions are available on the Hidden Web Page exclusively used for the serviceman.
Heat Roller
Pressure Roller
The heater lamp is in the heat roller, which heats the heat roller to
fuse toner onto paper.
The pressure roller is made of silicon rubber because of the follow-
ing reasons and purpose.
1) Paper is separated. (Since the heat roller is of higher hard-
ness, the pressure roller is deformed to separate paper toward
the heat roller.)
2) The nip quantity is increased to increase heat capacity for
paper.
3) By pressing paper with the flexible roller, toner is fused without
deformation.
The machine is provided with the following filter to remove ozone generated in the process section.
2
<20/23/26/31 cpm> <26/31 cpm>
OZFM LSUFM
PSFM
1.Block Diagram
A.System block diagram
(1) 20/23 cpm
RSPF
CCD-PWB
12V 3.3V 㼂㼛㼘㼡㼙㼑㻌㻾
㻿㻼㻲㻹㻻㼀㻻㻾
㻯㻯㻰 㻭 㻲 㻱 㻔㻴㼀㻤㻞㼂㻟㻤㻕
B/W 㻿㻼㼃㻿
㻔㼀㻯㻰㻞㻥㻝㻢㻕 㻯 㻭 㻹
R 0HFKDQLFDOORDGV
㻡㻟㻠㻜㻌㼜㼕㼤㼑㼘㻖㻌㻠㼘㼕㼚㼑 㻰 㻳 㻼 㻭㻰
G 655&638&
䠄㻠㻜㻜㼐㼜㼕䠅 㻿 㻯 㼄
B
㻝㻢㼎㼕㼠㼟
5V /('
6HQVRUV
633'f63('6&2963/66
㻯㻯㻰㻌㻰㼞㼕㼢㼑㼞
+20( 3/662&'
/(' 563)
326,7,21
'ULYHU 'ULYHU
6(1625
:DNH8S/('
EPM240T100C5
㻿㻿㻯㻳
+& 67$57 KEYs
(Includes ONK)
:DNH8S.(<
㻹㼍㼕㼚㻌㼡㼚㼕㼠㻌㻿㼑㼚㼟㼛㼞㼟
㻼㻵㻺㻘㻼㻻㻰㻘㻼㻻㻿 %X]]HU
㻰㻘㻹㻼㼃㻰 㻼㻹㻯㻸㻷
㻡㼂 㻞㻠㼂
QG &DVVHWWH
CRUM
2SWLRQDO
Dup 䠩䡋䡐䡋䡎 䠩䠽䡅䡊䠩䡋䡐䡋䡎 Toner Motor Mirror Motor
Lift Up Motor
LSU POWER HVU 7HPS
6HQVRU
SUPPLY
䠬䡋䡈䡕䡃䡋䡊
%\SDVV7UD\ VW &DVVHWWH 䠩䡋䡐䡋䡎 UG &DVVHWWH WK &DVVHWWH
FSP 5VEN,24V 2SWLRQDO 2SWLRQDO
0HFKDQLFDOORDGV Polygon Motor
Mechanical load
03)&
RRC,C1PUC
6HQVRUV Cassette
Drive Motor
03(' C1PED,C1SS
DRY HEATER Fuser UN
(Japan Only)
Lift Up Motor Lift Up Motor
7KHUPLVWRU[
RSPF
CCD-PWB
12V 3.3V 㼂㼛㼘㼡㼙㼑㻌㻾
㻿㻼㻲㻹㻻㼀㻻㻾
㻯㻯㻰 B/W 㻭 㻲 㻱 㻔㻴㼀㻤㻞㼂㻟㻤㻕
㻔㼀㻯㻰㻞㻥㻝㻢㻕 㻿㻼㼃㻿
R 㻯 㻭 㻹 0HFKDQLFDOORDGV
5340 pixel* 4line 㻰 㻳 㻼 㻭㻰
G 655&638&
䠄㻠㻜㻜㼐㼜㼕䠅 㻿 㻯 㼄
B
㻝㻢㼎㼕㼠㼟
5V /('
6HQVRUV
633'f63('6&2963/66
㻯㻯㻰㻌㻰㼞㼕㼢㼑㼞
/(' +20( 3/662&'
563)
'ULYHU 326,7,21
'ULYHU
6(1625
㻭㼕㼞
㻯㼛㼚㼐㼕㼠㼕㼛㼚㼑㼞
36:/(' (UURU/('
TCS Shift-Reg.
MMCL
EEPROM 'DWD/(' LEDs (ONLྵ䜐)
CPLD 16kb
PSPS :DNH8S/('
(26/31 cpm) EPM240T100C5 CPUCLK
+& 67$57 KEYs (ONKྵ䜐)
㻹㼍㼕㼚㻌㼡㼚㼕㼠㻌㻿㼑㼚㼟㼛㼞㼟 :DNH8S.(<
㻼㻵㻺㻘㻼㻻㻰㻘㻼㻻㻿㻰
㻹㻼㼃㻰 %X]]HU
㻼㻹㻯㻸㻷
㻡㼂 㻞㻠㼂
QG &DVVHWWH
CRUM
2SWLRQDO
Dup 䠩䡋䡐䡋䡎 䠩䠽䡅䡊䠩䡋䡐䡋䡎 Toner Motor Mirror Motor
Lift Up Motor
LSU POWER SUPPLY HVU 7HPS
䠬䡋䡈䡕䡃䡋䡊 +XPLGLW\
%\SDVV7UD\ VW &DVVHWWH VW &DVVHWWH 䠩䡋䡐䡋䡎 UG &DVVHWWH WK &DVVHWWH
5VEN,24V 6HQVRU
FSP FSP (26/31cpm) 2SWLRQDO 2SWLRQDO
0HFKDQLFDOORDGV Polygon Motor
Mechanical loads Mechanical loads
03)& RRC,C1PUC RRC,C1PUC,C1LUM
6HQVRUV Sensors Sensors
Cassette
Drive Motor
03(' C1PED,C1SS C1PED,C1SS,C1LUD
DRY HEATER Fuser UN
(Japan Only) new Lift Up
p Motor Lift Up
p Motor
7KHUPLVWRU[
L1 L2
Voltage
Li
Live Conversion
24V
Z1
5V
F3 TH2
AL1
Z2
L4
FW
L3 Generating
Circuit
HL_PR
T1 G
GND
6 2
GND
HL
THERMOSTAT
Power unit MCU PWB
9 9
)(7 7U OZNFN
OPTION CASETTE
7U 1.6䠝
C2LUM
'5,9(5 TNM
1.6䠝
CPFM
1.5䠝 Clutch
2䠝
Clutch Clutch
DV UN TCS Solenoid
SCOV
2.5䠝
B.AC power system diagram(24V)
1.5䠝
RSPF Driver PWB
'5,9(5 SPFM
0.5䠝
2.5䠝
Clutch
0.5䠝
Solenoid
DSW
1.5䠝
OpƟcal Unit
LED Driver PWB LED PWB
,179
LED PWB
9
5HJ CCD PWB
1.5䠝
'5,9(5 MIRM
ADUM
COIN
LSU Unit
PGM UN
,179
5HJ LD PWB
HL Relay 7U
MM
HV PWB
Power unit MCU PWB
1.5䠝
9 RSPF Relay PWB
)(7 Sensor
1.5䠝
NNB PWB
+6
USB HOST
6:
'&'&
59
'&'& 59
9SRí 1.5䠝
Sensor
CCD PWB
9&&
'&'&
OPE PWB
'&'&
CARTRIDGE PWB
9
ASIC
(1) 20/23 cpm
-#5 07"
3-2
6
. 3-2
6
. 3-0
6
.# ""
8(
!
2$ #. 2ED ""
8(
! #. 3-0
6
.# 3-2
6
. 3-2
6
.
6#, 6#, 6#, 6#,
22# 0303 0303 #05# #05# #05#
3. Actual wiring chart
A.Fan, Sensor, Motor, Clutch
""
0(
+
3#.
#33 #33
$
'.$ $
'.$ #33
6P
OFF 6,%$
#0%$ #0%$
$
'.$ $
'.$ #0%$
6P
OFF 6,%$
0). 0).
$
'.$ $
'.$ 0).
6P
OFF 6,%$
2
15.Feb
MCU PWB
B2B-XH-A (CN129) SMP-02V-NC SMR-02V-N SMR-02V-N
SMR-02V-N SMR-02V-N SMP-02V-NC B2B-XH-A-RD (CN127)(Red) 24VCL 1 1 24VCL 1
1 24VCL 1 1 24VCL /C1PUC 2 2 /C1PUC 2 C1PUC
RRC 2 /RRC 2 2 /RRC
B5B-PH-K-E(CN138)(Blue) AMP292130-3
5Vp-off 3 3 5VLED
SMR-02V-N SMR-02V-N SMP-02V-NC B2B-XH-A-E(CN139)(Blue) C1LUD 1 1 C1LUD C1LUD
1 24VCL 1 1 24VCL 26/31CPM GND 2 2 D-GND
PSPS 2 /PSPS 2 2 /PSPS 26/31CPM Models only
Models only C1LUM_D# 4 2 C1LUM_D
PGND 5 1 PGND C1LUM
24V B3B-PH-K-R(CN120)(Red)
24V 1 1 OZFMOUT B9B-PH-K-S(CN119) 179228-3(AMP)
TFM GND 3 2 PGND
26/31CPM C1SS 1 1 C1SS
LOCK 2 GND 3 OZFMLD Models only D-GND 2 2 D-GND C1SS
5Vp-off 3 3 5VLED
24V 1 PALR-03VF PAP-03V-S 179228-3(AMP)
GND 3 LOCK
26/31CPM C1PED 4 1 C1PED 1 1 C1PED
OZFM Models only
LOCK 2 D-GND 5 2 D-GND 2 2 D-GND C1PED
B3B-PH-K-S (CN109) 5Vp-off 6 3 5Vp-off 3 3 5VLED
24V 1 1 PSFMOUT PALR-03VF-R PAP-03V-R 179228-3(AMP)
LOCK 2 2 PSFM_LD
26/31CPM PIN 7 1 PIN 1 1 PIN
PSFM Models only
PGND 3 3 PGND D-GND 8 2 D-GND 2 2 D-GND PIN
5Vp-off 9 3 5Vp-off 3 3 5VLED
AMP292156-3 B04B-PASK-1(CN122)
24V 1 1 TFMOUT 3 1 TFMOUT
LSUFM PGND 3 3 GND 1 2 NC 26/31CPM B9B-PH-K-S(CN119) 03XR-6Y-P
LOCK 2 2 TFM_LD 2 3 PGND Models only C1SS 1 1 C1SS
179228-3 179228-3 4 TFM_LD D-GND 2 2 D-GND C1SS
5Vp-off 3 3 5VLED
03XR-6Y-P
AMP292156-3 B3B-PH-K-R(CN120)(Red) 26/31CPM C1PED 4 1 C1PED
24V 1 1 OZFMOUT 3 1 OZFMOUT Models only D-GND 5 2 D-GND C1PED
OZFM GND 3 3 GND 1 2 PGND 20/23CPM 5Vp-off 6 3 5VLED
LOCK 2 2 OZFM_LD 2 3 OZFM_LD Models only 03XR-6Y-P
179228-3 179228-3 PIN 7 1 PIN
D-GND 8 2 D-GND PIN
B3B-PH-K-E(CN141)(Blue) 5Vp-off 9 3 5VLED
5VLED 3 1 VCC3
MPWD MPWD 1 2 MPWD
D-GND 2 3 D-GND B4B-PH-K-R (CN135)
3.3Vp-off 1 1 3.3Vp-off
SMR-02V-N SMR-02V-N SMP-02V-NC B2B-XH-A-BK (CN128)(Black) 26/31CPM HUD_RA 2 2 HUD_RA HUD_RA/
1 24VCL 1 1 24VCL 26/31CPM Models Models only GND 3 3 GND
MPFC 2 /MPFC 2 2 /MPFC TH_RA 4 4 TH_RA
TH_RA
and 26/31CPM
Models except Japan
AMP292130-3 B6B-PH-K-S (CN123) B4B-PH-K-R (CN135) S4B-PH-K-S
5VLED 3 3 5Vp-off 3.3Vp-off 1 1 NC
MPED MPED 1 1 (MPED) 20/23CPM HUD_RA 2 2 NC
GND TH_RA
2
15.Feb
㻹㻯㼁㻌㻼㼃㻮 㻼㻛㻿
㻮㻝㻠㻛㻝㻡㻮㻙㻱㻴㻔㻯㻺㻝㻜㻤㻕 㻮㻝㻠㻛㻝㻡㻮㻙㻱㻴㻙㻭䠄㻯㻺㻞㻜㻝䠅㻌
㻛㻼㻻㻲㻲 㻝 㻝 㻛㻼㻻㻲㻲
B.DC, HV, DV
㻞㻠㼂㻼㻰 㻞 㻞 㻞㻠㼂
㻞㻠㼂㻼㻰 㻟 㻟 㻞㻠㼂
㻼㻳㻺㻰 㻠 㻠 㻼㻳㻺㻰
㻼㻳㻺㻰 㻡 㻡 㻼㻳㻺㻰
㻡㼂㻱㻺 㻢 㻢 㻡㼂
㻡㼂㻱㻺 㻣 㻣 㻡㼂
㻳㻺㻰 㻤 㻤 㻳㻺㻰
㻳㻺㻰 㻥 㻥 㻳㻺㻰
㻴㻸㻻㼁㼀㻝 㻝㻜 㻝㻜 㻴㻸㻻㼁㼀㻝
㻼㻾㼋㻯㼀㻾㻸 㻝㻝 㻝㻝 㻼㻾㻝
㻲㼃 㻝㻞 㻝㻞 㻲㼃
㻼㻳㻺㻰 㻝㻟 㻝㻟 㻰㻳㻺㻰
㻼㻳㻺㻰 㻝㻠 㻝㻠 㻰㻳㻺㻰
㻴㻸㻻㼁㼀㻞 㻝㻡 㻝㻡 㻴㻸㻻㼁㼀㻞
㻻㼚㼘㼥㻌㼒㼛㼞㻌㻞㻢㻛㻟㻝㼏㼜㼙
㻮㻝㻝㻮㻙㻼㻴㻙㻷㻙㻿㻔㻯㻺㻝㻝㻞㻕 㻮㻝㻝㻮㻙㻼㻴㻙㻷㻙㻿 㻴㼂
㻵㻺㼀㻞㻠㼂 㻝 㻝㻝 㻵㻺㼀㻞㻠㼂 㻹㻴㼂 㻝 MHV
㻼㻳㻺㻰 㻞 㻝㻜 㻳㻺㻰
㻰㼂㻮㻿㼋㻼㼃㻹㻛 㻟 㻥 㻰㼂㻮㻿㻌㻼㼃㻹
㻰㼂㻮㻿㼋㻾㻱㻹㻛 㻠 㻤 㻰㼂㻮㻿㻌㻾㻱㻹
㼀㻴㼂㻙㼋㻾㻱㻹㻛 㻡 㻣 㼀㻴㼂㻙㻌㻾㻱㻹
㼀㻴㼂㼋㻾㻱㻹㻛 㻢 㻢 㼀㻴㼂㻌㻾㻱㻹 㻳㻮 GB
㻰㻴㼂㼋㻾㻱㻹㻛 㻣 㻡 㻰㻴㼂㻌㻾㻱㻹 㻿㻼㻌㼙㼑㼠㼔㼛㼐
㼀㻯㻰㻭㻏 㻤 㻠 㼀㻯㻰㻭㻏
㻳㻮㻿㼋㻼㼃㻹㻛 㻥 㻟 㻳㻮㻌㻼㼃㻹
㻹㻴㼂㼋㻾㻱㻹㻛 㻝㻜 㻞 㻹㻴㼂㻌㻾㻱㻹 㼀㻴㼂 㻝 㼀㻴㼂
㻞㻠㼂㻯㻸 㻝㻝 㻝 㻞㻠㼂
㻰㻴㼂 㻰㻴㼂
㻔㻺㻯㻕
㻰㼂㻮㻿 㻔㼀㼛㻌㻰㼂㻌㻰㼞㼍㼣㼑㼞㻕
㻿㻼㻌㼙㼑㼠㼔㼛㼐
㻮㻠㻮㻙㻼㻴㻙㻷㻙㻿㻔㻯㻺㻝㻟㻞㻕 㻮㼁㻜㻠㻼䠉㼀㻾䠉㻼䠉㻴䠄㻰䠅䠄㻸㻲䠅䠄㻿㻺䠅
㻰㼂㻌㼁㻺㻵㼀
㻔 㻕
㻮㻠㻮㻙㻼㻴㻙㻷㻙㻿㻔㻯㻺㻝㻟㻞㻕 䡺䢙䡷 䡽 䡯䡵䡮㻌 䢄䡹㻌 㻌 㻛 㻌㻌 䠄 䠅䠄 䠅䠄 䠅
㻮㼁㻜㻠㻼䠉㼀㻾䠉㻼䠉㻴䠄㻰䠅䠄㻸㻲䠅䠄㻿㻺䠅
㻰㼂㻌㼁㻺㻵㼀
㻔㻰㼂㻿㻝㻕 㻝 㻟 㻔㻰㼂㻿㻝㻕 㻞 㻝
㻞㻠㼂㻯㻸 㻞 㻞 㻞㻠㼂㻯㻸 㻟 㻞
㻔㼀㻯㻿㻕 㻟 㻝 㻔㼀㻯㻿㻕 㻠 㻟 㼀㻯㻿 㻞㻢㻛㻟㻝㻌㼏㼜㼙
㻼㻳㻺㻰 㻠 㻠 㻼㻳㻺㻰 㻝 㻠
㻮㻠㻮㻙㻼㻴㻙㻷㻙㻱㻔㻯㻺㻝㻟㻜㻕 㻭㼀㻯㻌㻿㼑㼚㼟㼛㼞
㻔㻮㼘㼡㼑㻕 㼀㻿㻴㻾㻙㻜㻠㼂㻙㻷
㼂㻯㻯㻟 㻝 㻟 㼂㻯㻯㻟
㻯㻾㻹㼋㻿㻰㻭 㻞 㻝 㻯㻾㻹㼋㻿㻰㻭
㻯㻾㻹㼋㻿㻯㻸 㻟 㻞 㻯㻾㻹㼋㻿㻯㻸 㼀㼛㼚㼑㼞㻌㻯㼍㼞㼠㼞㼕㼐㼓㼑
㻳㻺㻰 㻠 㻠 㻳㻺㻰
MCU PWB PHR-4
C.Scanner
B4B-PH-K-S (CN115) 1 A/
MIRM_A/ 1 2 A
MIRM_A 2 3 B/
MIRM_B/ 3 4 B MIRM
MIRM_B 4 5 NC
6 A/
B3B-PH-K-S (CN118)
MHPOS 1 1 MHPOS
D-GND 2 2 D-GND MHPOS
5Vp-off 3 3 5Vp-off
PS PWB
Dehumidification SW
ONLY FOR JAPAN
䠄172074䠉7䠅Red
LIVE 1
䠄172074䠉1䠅White
DH䠉L 1
BK
BK
CN004
Li ve- WH 1
Neutral-WH 2 A䠉1 DH䠉N A䠉1
DH1
WH A䠉2 DH䠉L A䠉2
䠄ELP䠉02V䠅 䠄ELP䠉02V䠅
200V
CN001(B03P-VL-LF)
Live 1 Live THERMOSTAT1
F-GND 2 ( NC)
Neutra l 3 Neutral CN101(B02P-VT-LP)
HL_L 1 1 HL_L 1
INLET HL_N 2 2 HL_N 2
HL_UM
AC SW
SW IN (LIVE) 1 4 Live-in
SW IN (NEUTRAL) 1 2 Neutral - i n
VLP-04V
2
2
15.Feb
PS PWB
200V
CN001(B03P-VL-LF) 20/23CPM Models only
Live 1 Live THERMOSTAT1
F-GND 2 ( NC)
Neutra 3 Neutral CN101(B02P-VT-LP)
HL_L 1 1 HL_L 1
INLET HL_N 2 2 HL_N 2 HL_UM
THERMOSTAT1
CN101(B2P3-VH-B)
!-0
6 60$
'.$ 0'.$
34!24 0-$
,/#+ 0-?,$
0-#,+
E.LSU PWB, OPE PWB, CV PWB, NNB PWB
0/,9#,+
0/,9'/. -4
S,D-Model (standard)
""
0(
+
3 #. - 3"
0!3+
53"