Professional Documents
Culture Documents
G499
G499
P30305-X1118-G499-01-7618
EWSD
SYSTEM UPGRADE
CP-SW-SPLIT
V11,MB(B),MB(D) to V17/CCNC
CP113C with F:PIOP(A,B)
Project STD
Issued by
Communications Division
Hofmannstraße 51, D-81359 München
The reproduction, transmission or use of this document or its contents is not permitted without
express written authority. Offenders will be liable for damages. All rights, including rights
created by patent grant or registration of a utility model or design, are reserved.
Technical modifications possible.
Technical specifications and features are binding only insofar as they are specifically and
expressly agreed upon in a written contract.
SIEMENS AKTIENGESELLSCHAFT
0-2 P30305-X1118-G499-01-7618
TABLE OF CONTENTS
1. INTRODUCTION............................................................................................................. 1-1
1.1. Subject of the Procedure................................................................................... 1-1
1.2. Objective of the Procedure................................................................................ 1-1
1.3. Phases of the Procedure................................................................................... 1-2
1.4. Position in the Process with Procedure Interfaces............................................ 1-3
1.5. Scope of HW/FW/SW to be upgraded .............................................................. 1-3
1.6. Time requirements for the Execution ................................................................ 1-4
1.7. Aspects of Quality ............................................................................................. 1-4
1.7.1. Protection against Electrostatic Discharge.......................................... 1-4
1.8. How to read this Procedure............................................................................... 1-5
2. PREREQUISITIES .......................................................................................................... 2-1
2.1. Hardware / Firmware V17/CCNC ...................................................................... 2-1
2.1.1. Required Status .................................................................................. 2-1
2.1.2. Compatible HW / FW Modifications..................................................... 2-1
2.1.3. Non-compatible HW/FW Modifications................................................ 2-1
2.1.4. Recommendations for Memory Capacity CP113C.............................. 2-1
2.1.5. Additional Equipment for System Upgrade ......................................... 2-2
2.2. References to MTD / MOD for file saving and file transfer................................ 2-2
2.3. Software / Tools ................................................................................................ 2-3
2.3.1. System Upgrade with complete APS V17/CCNC................................ 2-3
2.3.2. System Upgrade - Command Files ..................................................... 2-4
2.3.2.1. Command Files V11 .................................................................. 2-4
2.3.2.2. Command Files V17/CCNC ....................................................... 2-4
2.3.2.3. Auxiliary Files for Function OSU V11 and V17/CCNC ............... 2-5
2.3.3. System Upgrade - Patch Files............................................................. 2-5
2.3.3.1. Patch Command Files APS V11 ................................................ 2-5
2.3.3.2. Patch Command Files APS V17/CCNC..................................... 2-5
2.3.4. Common Patches................................................................................ 2-5
2.4. Documentation .................................................................................................. 2-6
3. BASIC OPERATION....................................................................................................... 3-1
3.1. Overview / Flow Diagram .................................................................................. 3-1
3.1.1. Phase 1: Preparation .......................................................................... 3-2
3.1.2. Phase 2: Processor Splitting ............................................................... 3-4
3.1.3. Phase 3: Cut over................................................................................ 3-6
3.1.4. Phase 4: Post processing ................................................................... 3-8
4. DETAILED DESCRIPTION PHASE 1: PREPARATION ............................................... 4-1
4.1. Establishing a Test Concept ............................................................................. 4-1
4.2. Transferring the V11 Command Files and Patch Files to Disks........................ 4-2
4.3. Test of the CP113C........................................................................................... 4-2
4.4. Diagnosis of the Periphery ................................................................................ 4-3
4.4.1. Verification of MB / SN Capacity Stages ............................................. 4-3
4.4.2. Diagnosis of the MB ............................................................................ 4-4
4.4.3. Diagnosis of the SN ............................................................................ 4-5
4.4.4. Check of CCG - IOPMB Connection ................................................... 4-6
4.4.5. Check of the SYPC - IOPMB Connection ........................................... 4-6
4.4.6. Diagnosis of the CCNC ....................................................................... 4-7
4.5. Checking the LTGs ........................................................................................... 4-7
4.6. Installation of MP, OMT-1 and MOD-1.............................................................. 4-8
4.6.1. Installation of Maintenance Panel ....................................................... 4-8
4.6.2. Installation of OMT-1 ........................................................................... 4-9
4.6.3. Installation of MOD-1......................................................................... 4-10
P30305-X1118-G499-01-7618 0-3
4.7. Saving of APS V11.......................................................................................... 4-12
4.8. Display of V5-Links ......................................................................................... 4-12
4.9. Saving of Exchange Files APS V11 ................................................................ 4-13
4.10. System Status Inquiry of APS V11.................................................................. 4-16
4.10.1. Checking System States ................................................................... 4-16
4.11. Creating CP Upgrade Tables in APS V11....................................................... 4-20
4.12. Changing Meter Saving Time.......................................................................... 4-21
4.13. Replacing File SY.INSTALL ............................................................................ 4-21
4.14. Processing Logfiles ......................................................................................... 4-22
4.14.1. Processing and Saving Log file (1) ................................................... 4-22
4.14.1.1. Checking the Log file (1) .......................................................... 4-22
4.14.1.2. Conversion of Log file (1) on the PC........................................ 4-23
5. DETAILED DESCRIPTION PHASE 2: PROCESSOR SPLITTING ............................ 5-1
5.1. Instructions for CP SW-Splitting........................................................................ 5-1
5.2. Splitting the Processors and CCNPs ................................................................ 5-2
5.3. Loading complete APS V17/CCNC in the NSS................................................. 5-5
5.4. Installation Recovery with APS V17/CCNC in the NSS .................................... 5-9
5.5. Inquiry of Processor and CCNC Status in the NSS ........................................ 5-12
5.5.1. Inquiry of the Processor Status ......................................................... 5-12
5.5.2. Setting Split Option and Restart of Installation Recovery.................. 5-13
5.5.3. Inquiry of the CCNP Status ............................................................... 5-15
5.5.4. Configuration of the CCNPs .............................................................. 5-15
5.5.5. Inquiry of the CCNP Status ............................................................... 5-16
5.5.6. Configuration of IOC-2,3 in DE-Type DE54 ...................................... 5-17
5.5.7. Activating the CCNP-1 ...................................................................... 5-17
5.6. Preparation of both APS V11 and V17/CCNC ................................................ 5-18
5.6.1. Transferring V17/CCNC Command Files in the NSS........................ 5-18
5.6.2. Starting Processes in the NSS .......................................................... 5-18
5.6.3. Creating and Checking Files in the NSS ........................................... 5-19
5.6.3.1. Creating CA Files..................................................................... 5-19
5.6.3.2. Creating IA Files ...................................................................... 5-20
5.6.3.3. Starting IACHASTA Registration ............................................. 5-21
5.6.3.4. Checking Security Files ........................................................... 5-21
5.6.4. Changing Meter Saving Time in the NSS.......................................... 5-22
5.6.5. Checking Data for Meter Administration in the SS and NSS............. 5-22
5.6.6. Deactivation of Routine Tests ........................................................... 5-22
5.6.6.1. Deactivation of Routine Tests in the NSS................................ 5-22
5.6.6.2. Deactivation of Routine Tests in the SS .................................. 5-23
5.6.7. Creating and Checking the File SU.UCT in the NSS ........................ 5-23
5.6.8. Expansion of the File SG.OPER in the NSS ..................................... 5-24
5.6.9. Interrogation of Emergency Call Station Party Alarms in SS ............ 5-24
5.6.10. Incorporating the Logfile (1) in the NSS ............................................ 5-25
5.6.10.1. IOC-2,3 and CAP Status Request in the NSS ......................... 5-26
5.6.10.2. Status Requests....................................................................... 5-27
5.6.10.2.1. LTG Status Requests in the SS...................................... 5-27
5.6.10.2.2. MB(B) Status Requests in the NSS ................................ 5-27
5.6.10.2.3. Change of MB-Type from MB(B) to MB(D) ..................... 5-29
5.6.10.2.4. MB(D) Status Requests in the NSS................................ 5-30
5.6.10.2.5. SN Status Request in the NSS ....................................... 5-31
5.6.10.3. Interrogation of DIU and CR States in the SS and NSS .......... 5-32
5.6.11. Setting the Upgrade Flag in the NSS ................................................ 5-33
5.7. Deactivation of Links in the SS ....................................................................... 5-33
5.7.1. Deactivation of CSC-Links ................................................................ 5-33
5.7.2. Deactivation of X25-Links.................................................................. 5-34
5.8. Blocking Subscriber Controlled Inputs in V11 ................................................. 5-34
0-4 P30305-X1118-G499-01-7618
5.9. Processing and Saving Logfile (2) in the SS................................................... 5-34
5.9.1. Checking the LG-Logfile (2) .............................................................. 5-34
5.9.2. Saving and Converting of Logfile (2) / Dest. APS V17/CCNC........... 5-35
5.10. Incorporating Log file (2) in the NSS ............................................................... 5-36
5.11. Blocking Subscriber Controlled Inputs in the NSS .......................................... 5-37
5.12. Updating Charge Files on MDD-0 in the SS ................................................... 5-37
6. DETAILED DESCRIPTION PHASE 3: CUT OVER.................................................... 6-1
6.1. Instructions for APS Change over..................................................................... 6-1
6.2. Startup and Change over from APS V11 to APS V17/CCNC ........................... 6-1
6.2.1. Ending Installation Recovery in the NSS............................................. 6-1
6.2.2. Startup of APS V17/CCNC in the NSS................................................ 6-1
6.3. Restoring System Redundancy......................................................................... 6-4
6.3.1. Activation of OMT-0 and OMT-1 ......................................................... 6-4
6.3.2. Quick Check of System Status............................................................ 6-4
6.4. Activation of Periphery Side 0 and Side 1......................................................... 6-4
6.4.1. Resetting the Split Option ................................................................... 6-4
6.4.2. Diagnosis of the MB ............................................................................ 6-5
6.4.3. Activation of CCNP-0 .......................................................................... 6-5
6.4.4. Activation of CAPs............................................................................... 6-5
6.4.5. Checking SYP, TIME and NUCs/IPNUCs ........................................... 6-6
6.4.6. Interrogation of Alarms from Emergency Call Station Party................ 6-7
6.4.7. Checking Charge Files ........................................................................ 6-7
6.4.8. Restoring original Meter Saving Points ............................................... 6-8
6.5. System Check APS V17/CCNC ........................................................................ 6-8
7. DETAILED DESCRIPTION PHASE 4: POST PROCESSING ..................................... 7-1
7.1. Unblocking Subscriber Controlled Inputs .......................................................... 7-1
7.2. Updating the Database ..................................................................................... 7-1
7.3. Activating Links ................................................................................................. 7-2
7.3.1. Activating CSC-Links........................................................................... 7-2
7.3.2. Activating X25-Links............................................................................ 7-3
7.4. File Handling ..................................................................................................... 7-3
7.4.1. CP SW-Splitting................................................................................... 7-3
7.4.2. Installation Recovery with APS V11 in the NSS.................................. 7-4
7.4.3. Starting Processes in the NSS ............................................................ 7-6
7.4.4. Saving IA Files in the NSS .................................................................. 7-6
7.4.4.1. Saving File IA.ICAMA ................................................................ 7-6
7.4.4.2. Saving File IA.ICMAL................................................................. 7-7
7.4.4.3. Saving File IA.ICMOB and IA.ICFIR .......................................... 7-7
7.4.4.4. Saving File IA.ICIAR .................................................................. 7-8
7.4.4.5. Saving Files IA.ICIAR1 and IA.ICIAR2 ...................................... 7-8
7.4.4.6. Saving File IA.ICINA .................................................................. 7-9
7.4.4.7. Saving File IA.IC<type> ............................................................. 7-9
7.4.5. Saving IACHASTA Files in the NSS.................................................. 7-10
7.4.6. Saving Security Files in the NSS....................................................... 7-10
7.4.7. Saving CA Files for Meter Accounting in the NSS ............................ 7-11
7.4.8. Saving CA Files for Meter Regeneration in the NSS......................... 7-11
7.4.9. Merging the Processors .................................................................... 7-12
7.5. Regeneration of Charge Meters...................................................................... 7-12
7.6. Reduction of File SG.OPER............................................................................ 7-14
7.7. Deleting Files .................................................................................................. 7-14
7.7.1. Deleting Command and Temporary Files.......................................... 7-14
7.7.2. Deleting Logfiles................................................................................ 7-15
7.7.3. Deleting APS Generations ................................................................ 7-15
7.8. Activating Routine Tests ................................................................................. 7-15
P30305-X1118-G499-01-7618 0-5
7.9. Activating Jobs ................................................................................................ 7-15
7.10. Activating the MDD-0 (after 24h observation period) ...................................... 7-16
7.11. Removing MP, OMT-1 and MOD-1 ................................................................. 7-16
7.11.1. Removing the MP.............................................................................. 7-16
7.11.2. Removing the OMT-1 ........................................................................ 7-16
7.11.3. Removing the MOD-1........................................................................ 7-17
7.12. Saving of APS V17/CCNC .............................................................................. 7-18
7.13. Casino Outage Report .................................................................................... 7-18
8. INTERRUPTING THE UPGRADE PROCEDURE .......................................................... 8-1
8.1. Concept of Fallback .......................................................................................... 8-1
8.2. Fallback Procedure 1: Fallback from Installation Recovery .............................. 8-2
8.2.1. Interrupting the Installation Recovery V17/CCNC in the NSS............. 8-2
8.2.2. Merging the Processors ...................................................................... 8-2
8.2.3. Resetting the Split Option ................................................................... 8-3
8.2.4. Activating the CCNP-1 ........................................................................ 8-3
8.2.5. Deactivating System Upgrade............................................................. 8-3
8.2.6. Restoring original Time for Meter Saving ............................................ 8-4
8.2.7. Setting the LOG Function.................................................................... 8-4
8.2.8. Activating the Links ............................................................................. 8-4
8.2.8.1. Activating the CSC-Links ........................................................... 8-4
8.2.8.2. Activating the X25 Links............................................................. 8-5
8.2.9. Reactivating Jobs ................................................................................ 8-5
8.2.10. Activating the Routine Tests ............................................................... 8-5
8.2.11. Checking System Redundancy ........................................................... 8-5
8.2.12. Deleting auxiliary Files ........................................................................ 8-6
8.2.13. Removing the MP................................................................................ 8-6
8.2.14. Removing the OMT-1 .......................................................................... 8-6
8.2.15. Removing the MOD-1.......................................................................... 8-6
8.2.16. Saving the APS V11............................................................................ 8-7
8.3. Fallback Procedure 2: Fallback from MDD-1 with V11 .................................... 8-8
8.3.1. Interrupting System Operation with APS V17/CCNC .......................... 8-8
8.3.2. Installation Recovery with APS V11 .................................................... 8-8
8.3.3. Resetting the Split Option ................................................................. 8-10
8.3.4. Configuration of the Periphery........................................................... 8-10
8.3.5. Canceling auxiliary Patches .............................................................. 8-10
8.3.6. Startup ISTART2F with APS V11...................................................... 8-10
8.3.7. Quick Check of APS V11 .................................................................. 8-11
8.3.8. Activating CCG and SYP................................................................... 8-11
8.3.9. Activating the CCNP-1 ...................................................................... 8-12
8.3.10. Activating the MDD-1 ........................................................................ 8-12
8.3.11. Restoring original Time for Meter Saving .......................................... 8-12
8.3.12. Setting the LOG Function.................................................................. 8-13
8.3.13. Activating the Links ........................................................................... 8-13
8.3.13.1. Activating the CSC-Links ......................................................... 8-13
8.3.13.2. Activating the X25 Links........................................................... 8-13
8.3.14. Reactivating Jobs .............................................................................. 8-14
8.3.15. Activating the Routine Tests ............................................................. 8-14
8.3.16. Checking System Redundancy ......................................................... 8-14
8.3.17. Deleting auxiliary Files ...................................................................... 8-14
8.3.18. Removing the MP.............................................................................. 8-15
8.3.19. Removing the OMT-0 ........................................................................ 8-15
8.3.20. Removing the MOD-0........................................................................ 8-15
8.3.21. Saving the APS V11.......................................................................... 8-16
8.4. Fallback Procedure 3: Fallback from save MO V11........................................ 8-17
8.4.1. Blocking Subscriber Controlled Inputs .............................................. 8-17
0-6 P30305-X1118-G499-01-7618
8.4.2. Deactivating X25-Links...................................................................... 8-17
8.4.3. Deactivating CSC-Links .................................................................... 8-17
8.4.4. Saving Charge Files to Disks ............................................................ 8-18
8.4.5. Saving CA Files for Fallback ............................................................. 8-18
8.4.6. Saving Logfile V17/CCNC ................................................................. 8-18
8.4.7. Interrupting System Operation with V17/CCNC ................................ 8-19
8.4.8. Loading APS V11 .............................................................................. 8-20
8.4.9. Manual Startup with APS V11 ........................................................... 8-24
8.4.10. Quick Check ...................................................................................... 8-25
8.4.11. Activating BAP-1 ............................................................................... 8-25
8.4.12. Configuration of MDD-1..................................................................... 8-26
8.4.13. Logfile handling ................................................................................. 8-26
8.4.14. File Handling ..................................................................................... 8-28
8.4.14.1. CP SW-Splitting ....................................................................... 8-28
8.4.14.2. Installation Recovery with APS V17/CCNC ............................. 8-29
8.4.14.3. Starting Processes................................................................... 8-30
8.4.14.4. Saving IA Files ......................................................................... 8-30
8.4.14.4.1. Saving File IA.ICAMA ..................................................... 8-31
8.4.14.4.2. Saving File IA.ICMAL...................................................... 8-31
8.4.14.4.3. Saving File IA.ICMOB and IA.ICFIR ............................... 8-32
8.4.14.4.4. Saving File IA.ICIAR ....................................................... 8-32
8.4.14.4.5. Saving Files IA.ICIAR1 and IA.ICIAR2 ........................... 8-33
8.4.14.4.6. Saving File IA.ICINA ....................................................... 8-33
8.4.14.4.7. Saving File IA.IC<type> .................................................. 8-34
8.4.14.4.8. Saving IACHASTA Files ................................................. 8-34
8.4.14.5. Saving Security Files in the NSS ............................................. 8-35
8.4.14.6. Merging the Processors ........................................................... 8-35
8.4.15. Removing MOD-1.............................................................................. 8-36
8.4.16. Removing the MP.............................................................................. 8-37
8.4.17. Removing the OMT-1 ........................................................................ 8-37
8.5. Double Disk Failure......................................................................................... 8-38
9. STARTUP ISTART2F WITH APS V17/CCNC................................................................ 8-1
9.1.1. Interrupting Startup and Change over to APS V17/CCNC in NSS...... 9-1
9.1.2. Installation Recovery with APS V17/CCNC......................................... 9-1
9.1.3. Resetting the Split Option ................................................................... 9-2
9.1.4. Configuration of the Periphery............................................................. 9-3
9.1.5. Deactivating Function OSU ................................................................. 9-3
9.1.6. Startup ISTART2F with APS V17/CCNC ............................................ 9-3
10. PROJECT RELATED ITEMS ....................................................................................... 10-1
10.1. Downward-compatible HW/FW Modifications ................................................. 10-1
10.2. Not downward-compatible HW/FW Modifications ........................................... 10-1
11. ABBREVIATIONS ........................................................................................................ 11-1
P30305-X1118-G499-01-7618 0-7
13.1.3. Frame Layout for Capacity Stage DE54............................................ 13-5
13.1.3.1. Frame Layout with F:PIOP(A) .................................................. 13-5
13.1.3.2. Assignment of Processors with F:PIOP(A) .............................. 13-6
13.1.3.3. Frame Layout with F:PIOP(B) .................................................. 13-7
13.1.3.4. Assignment of Processor with F:PIOP(B) ................................ 13-8
13.1.4. Fuse Assignment to the Functional CP Units.................................... 13-9
13.1.4.1. R:CP113C with F:PIOP(A) ....................................................... 13-9
13.1.4.2. R:CP113C with F:PIOP(B) ..................................................... 13-10
13.1.5. Allocation of Log./Phys. IOPMBs to the Periphery .......................... 13-11
13.1.5.1. R:CP113C with F:PIOP(A) ..................................................... 13-11
13.1.5.2. R:CP113C with F:PIOP(B) ..................................................... 13-11
13.2. Message Buffer MB(B).................................................................................. 13-12
13.2.1. MB(B) Racks ................................................................................... 13-12
13.2.2. Frame Equipping MB(B).................................................................. 13-13
13.3. Message Buffer MB(D) (up to DE52) ............................................................ 13-14
13.3.1. R:LTGN (7ft) with F:MBD ................................................................ 13-14
13.3.2. R:LTGN (8ft) with F:MBD ................................................................ 13-15
13.3.3. Fuse Assignment for R:LTG(N) (with MB(D)).................................. 13-16
13.3.4. HW and FW for MB(D) .................................................................... 13-16
13.3.5. MB(D) Frames................................................................................. 13-17
13.4. Command Files V11...................................................................................... 13-18
13.4.1. Command File CF.11.ACTCSCG499.............................................. 13-18
13.4.2. Command File CF.11.ACTX25G499............................................... 13-19
13.4.3. Command File CF.11.CANPATG499.............................................. 13-20
13.4.4. Command File CF.11.CPTESTG499 .............................................. 13-21
13.4.5. Command File CF.11.CRSUUCTG499........................................... 13-23
13.4.6. Command File CF.11.DIAGCCNG499............................................ 13-24
13.4.7. Command File CF.11.DIAGMB0G499 ............................................ 13-26
13.4.8. Command File CF.11.DIAGMB1G499 ............................................ 13-28
13.4.9. Command File CF.11.DIUSTATG499 ............................................. 13-30
13.4.10. Command File CF.11.MBSNPLAG499 ........................................... 13-32
13.4.11. Command File CF.11.PLACSCG499 .............................................. 13-35
13.4.12. Command File CF.11.PLAX25G499 ............................................... 13-36
13.4.13. Command File CF.11.REGMEMTG499 .......................................... 13-37
13.4.14. Command File CF.11.REGMEMOG499 ......................................... 13-40
13.4.15. Command File CF.11.PROG499..................................................... 13-43
13.4.16. Command File CF.11.SYSTATG499 .............................................. 13-44
13.4.17. Command File CF.11.UPDFILEG499 ............................................. 13-46
13.4.18. Command File CF.11.V5CHECKG499 ........................................... 13-48
13.5. Command Files V17/CCNC .......................................................................... 13-49
13.5.1. Command File CF.17.ACTCAPG499.............................................. 13-49
13.5.2. Command File CF.17.ACTX25G499............................................... 13-51
13.5.3. Command File CF.17.CRSUUCTG499........................................... 13-52
13.5.4. Command File CF.17.DIAGMB0G499 ............................................ 13-53
13.5.5. Command File CF.17.DIAGMB1G499 ............................................ 13-55
13.5.6. Command File CF.17.DIUSTATG499 ............................................. 13-57
13.5.7. Command File CF.17.MBSNPLAG499 ........................................... 13-58
13.5.8. Command File CF.17.HEXIOCAG499 ............................................ 13-61
13.5.9. Command File CF.17.HEXLTGG499 .............................................. 13-62
13.5.10. Command File CF.17.HEXMBBG499 ............................................. 13-63
13.5.11. Command File CF.17.HEXMBDG499 ............................................. 13-64
13.5.12. Command File CF.17.HEXSNBG499.............................................. 13-65
13.5.13. Command File CF.17.OPERMAXG499 .......................................... 13-66
13.5.14. Command File CF.17.OPERMING499............................................ 13-67
13.5.15. Command File CF.17.PLACSCG499 .............................................. 13-68
13.5.16. Command File CF.17.PLAX25G499 ............................................... 13-69
0-8 P30305-X1118-G499-01-7618
13.5.17. Command File CF.17.PROG499..................................................... 13-70
13.5.18. Command File CF.17.SYSTATG499 .............................................. 13-71
13.5.19. Command File CF.17.UPDFILEG499 ............................................. 13-73
13.6. Patch Command Files V11 ........................................................................... 13-75
13.6.1. Patch Command File PA.11.B2925L2Z .......................................... 13-75
13.6.2. Patch Command File PA.11.B2925L2J........................................... 13-77
13.6.3. Patch Command File PA.11.SPLITCPZ.......................................... 13-78
13.6.4. Patch Command File PA.11.SPLITCPJ .......................................... 13-80
13.7. Patch Command Files V17/CCNC ................................................................ 13-81
14. CHANGE REQUESTS TO THE SYSTEM UPGRADE PROCEDURE ......................... 14-1
P30305-X1118-G499-01-7618 0-9
This page was left intentionally blank!
0-10 P30305-X1118-G499-01-7618
1. INTRODUCTION
In this procedure description, the required activities are handled in detail and in chronological
order.
Please note that any changes to the contents of this procedure must first be approved by
PSE SMC CI M in good time (2 weeks before the first application). Suggested modifications,
see Chapter 14 / Change Request, must be submitted contacting PSE SMC CI M:
PSE SMC CI M must give its approval before the modifications are allowed.
P30305-X1118-G499-01-7618 1-1
1.3. Phases of the Procedure
The System Upgrade procedure is divided into four phases:
Phase 1 Preparation
All preparatory operations which can be done before (not time critical) are carried out in this
phase.
APS V11
Diagnosis of CP and periphery
Installing MP:CP113, OMT-1 and MOD-1
Saving of APS V11
Saving of exchange files
System status inquiry
Processing and saving logfiles
In this phase the CP is split and the APS V17/CCNC is loaded and prepared in the non
switching system NSS.
CP SW-Splitting of the CP113C and CCNPs
Loading the complete APS V17/CCNC in the NSS
Installation Recovery and preparation of APS V17/CCNC
Preparation of APS V11 in the SS
Incorporating log files in the NSS
Updating charge files on disk in the SS
Phase 4 Post-Processing
APS V17/CCNC
Updating database
Activating and testing CSC/X25-links
CP SW-Splitting for file handling
Installation Recovery and saving charge files in NSS with APS V11
Merging processors
Regeneration of charge meters in APS V17/CCNC
Restoring system renundancy and original state
Removing MP, OMT-1 and MOD-1
Activating MDD-0
Saving of APS V17/CCNC
1-2 P30305-X1118-G499-01-7618
1.4. Position in the Process with Procedure Interfaces
The following overview shows the System Upgrade process with all the procedures and the
position of the CP SW-SPLIT.
System Upgrade
SW-SPLIT
PROCEDURE
V11,MB(B),MB(D) to V17/CCNC
CP113C F:PIOP(A,B)
P30305-X1118-G499-01-7618 1-3
1.6. Time requirements for the Execution
The duration for executing the Upgrade Procedure depends on type of exchange, logfile
handling , used charge types etc. The average time is about 12 hours.
The system outage for the changeover to the new APS is about 40 minute.
1-4 P30305-X1118-G499-01-7618
1.8. How to read this Procedure
When carrying out this procedure you should know exactly what the used symbols mean:
PC Enter command on PC
Operator intervention
P30305-X1118-G499-01-7618 1-5
This page was left intentionally blank !
1-6 P30305-X1118-G499-01-7618
2. PREREQUISITIES
Memory capacity of CMY / standard features: 256 MByte for up to 46.000 ports
512 MByte for more than 46.000 ports
P30305-X1118-G499-01-7618 2-1
2.1.5. Additional Equipment for System Upgrade
A Maintenance Panel MP must be available. The MP does not belong to the standard
equipment of CP113C, it should be obtainable in the local TAC department.
As the processors operate in split-mode, processors equipped with only one OMT (OMT-0)
must be provided with a second PC or CT-Boot as OMT-1.
Additional to MOD-0, a second MOD as MOD-1 with own power supply must be provided
for log and charge file handling.
2.2. References to MTD / MOD for file saving and file transfer
In the past, MTD and magnetic tape as medium was used for file saving and file transfer. This
technology became outdated and meanwhile was replaced by the MOD (Magneto Optical disk
drive) as drive assembly and MO (Magneto Optical disk) as medium. Now the new EWSD
switches are only equipped with MOD-0 instead of MTD-0. All active switches were also
equipped in the meantime with a MOD-0. Therefore in this procedure, file saving and file
transfer process is described only by MOD/MO. Of course magnetic tapes still can be used with
presence of a MTD. The appropriate commands deviating from the MOD/MO handling are to
be taken from the CML manuals.
Labeling of MO’s:
Differently than magnetic tapes news MO’s must be labeled before first use with the command:
So that the command can be implemented, the MOD-<x> must be configured to MBL. After
labeling it has to be activated again.
2-2 P30305-X1118-G499-01-7618
2.3. Software / Tools
File Content
SY.INSTALL Installation monitor
SY.GENLIST List of generations
SY.TASKLIB CP software (resident part)
SY.LOADLIB.LA Library of reloadable processes
SY.LOADLIB.MA Library of masks
SY.LOADLIB.CA Non-resident command description
SY.PSW.Txxx xxx = LTG load types
SY.PSW.T097 CCNC SW: CPI
SY.PSW.T098 CCNC SW: SIMP code
SY.SIMP CCNC SW: SIMP database
SY.PSW.T100 IOP:SCDP SW
SY.PSW.T121 IOP:UNI SW
SY.SEMILIB Library of semipermanent data
SY.UPLOG Logging file for SY.SEMILIB
SY.VSD.BACKUP Library for VSD database (Subscriber controlled inputs SCI)
SY.MSGXREF Reference list of messages
all CP patches
all GP patches
all CCNC patches
ODAGEN extension
Database
P30305-X1118-G499-01-7618 2-3
2.3.2. System Upgrade - Command Files
The execution of the procedure is supported by command files which must be available on
magneto optical disk MO.
2-4 P30305-X1118-G499-01-7618
2.3.2.3. Auxiliary Files for Function OSU V11 and V17/CCNC
File Content
SU.UCT Upgrade Control Table
P30305-X1118-G499-01-7618 2-5
2.4. Documentation
For execution of the System Upgrade procedure, the following manuals are necessary:
MMN:CP113C V11
NM:CP113C V11
MMN:SW:113 V11
MMN:CCS7 V11
MMN:CP113C V17/CCNC
NM:CP113C V17/CCNC
MMN:SW V17/CCNC
MMN:CCS7 V17/CCNC
2-6 P30305-X1118-G499-01-7618
3. BASIC OPERATION
For each phase, a synoptical diagram is depicted on the left page of the document.
A short description in a form of a flow diagram is arranged on each right page.
P30305-X1118-G499-01-7618 3-1
3.1.1. Phase 1: Preparation
Subscr.
MUXM-0x MUXM-1x
SN-0 SN-1
SILT... SILT...
SILTC-0... SILTC-1...
IOC-0 / 2 IOC-1 / 3
3-2 P30305-X1118-G499-01-7618
Phase 1: Preparation
P30305-X1118-G499-01-7618 3-3
3.1.2. Phase 2: Processor Splitting
Subscr.
MUXM-0x MUXM-1x
SN-0 SN-1
SILT... SILT...
SILTC-0... SILTC-1...
IOC-0 / 2 IOC-1 / 3
Phase 2: Processor Splitting SW-Splitting of CPs and CCNPs in system SS and NSS
3-4 P30305-X1118-G499-01-7618
Phase 2: Processor and Periphery Splitting
CP-0 Preparation of both APS V11 5.6 CP-1 Preparation of both APS V11 5.6
and V17/CCNC and V17/CCNC
P30305-X1118-G499-01-7618 3-5
3.1.3. Phase 3: Cut over
Subscr.
MUXM-0x MUXM-1x
SN-0 SN-1
SILT... SILT...
SILTC-0... SILTC-1...
IOC-0 / 2 IOC-1 / 3
Phase 3: Cut over Startup and changeover from APS V11 to APS V17/CCNC
3-6 P30305-X1118-G499-01-7618
Phase 3: Cut over
P30305-X1118-G499-01-7618 3-7
3.1.4. Phase 4: Post processing
Subscr.
MUXM-0x MUXM-1x
SN-0 SN-1
SILT... SILT...
SILTC-0... SILTC-1...
IOC-0 / 2 IOC-1 / 3
3-8 P30305-X1118-G499-01-7618
Phase 4: Post processing
P30305-X1118-G499-01-7618 3-9
CP-0/1 Regeneration of Charge Meters 7.5
3-10 P30305-X1118-G499-01-7618
4. DETAILED DESCRIPTION PHASE 1: PREPARATION
All preparatory operations which can be done before (not time critical) are carried out in this
phase. This supports the smooth handling of the Upgrade Procedure.
Because this test is exchange-specific, a suitable test method must be prepared by the service
personnel involved.
Switching equipment
• Outgoing/Incoming traffic:
Test calls via each trunk group
Test calls with all types of signaling
Test calls to international destinations (time announcement)
Transit calls
Charges
Note:
The test concept has to be tested first with APS V11.
P30305-X1118-G499-01-7618 4-1
4.2. Transferring the V11 Command Files and Patch Files to
Disks
/ <STAT SSP;
4-2 P30305-X1118-G499-01-7618
4.4. Diagnosis of the Periphery
The periphery must be fault free because the system must run in phases without redundancy
during the System Upgrade. For this reason, these devices have to be diagnosed and any
detected faults cleared.
Diagnose periphery in a low traffic period.
Each first MBUL unit per MB frame serves apart from TSG connection also for the clock supply
of the respective MB group. This implies, that in partly equipped Switching Networks SN:DE52
or SN:DE54, MBULs may exist without TSGs connected.
These MBULs should be in status ACT. If they are in PLA, they have to be configured to ACT.
/ <DISP EXDDAT;
Note:
Use rack and frame layouts in Chapter 13.2 for MB(B) to localize the MBULs (M:MDM)
concerned to the not existing TSGs.
/ <STAT SN;
<STAT MB;
continue
P30305-X1118-G499-01-7618 4-3
! MBULs without TSGs are in PLA
/ <CONF MBUL: MB=<0 and 1>, MBUL =<no>, OST=MBL; Configure all MBULs
<CONF MBUL: MB=<0 and 1>, MBUL =<no>, OST=ACT; without TSG to ACT
<STAT MB;
! MBULs without TSGs are in ACT
/ <STAT MB;
<STAT SN;
<STAT CCNC:UNIT=MUXM-X;
4-4 P30305-X1118-G499-01-7618
4.4.3. Diagnosis of the SN
/ <STAT SN;
P30305-X1118-G499-01-7618 4-5
4.4.4. Check of CCG - IOPMB Connection
Check if CCGs remain in status active, when configuring the corresponding IOPMBs.
/ <STAT CCG;
/ <CONF IOP:IOP=IOPMB-40,OST=MBL;
/ <CONF IOP:IOP=IOPMB-40,OST=ACT;
<CONF IOP:IOP=IOPMB-41,OST=MBL;
/ <STAT CCG;
<CONF IOP:IOP=IOPMB-41,OST=ACT;
/ <STAT SYP;
! SYP in ACT
/ <CONF IOP:IOP=IOPMB-42,OST=MBL;
/ <CONF IOP:IOP=IOPMB-42,OST=ACT;
<CONF IOP:IOP=IOPMB-43,OST=MBL;
/ <STAT SYP;
<CONF IOP:IOP=IOPMB-43,OST=ACT;
4-6 P30305-X1118-G499-01-7618
4.4.6. Diagnosis of the CCNC
Each CCNP is diagnosed from CP-0 as well as from CP-1 by the following command file.
/ <DISP LTG:LTG=X-X;
<STAT LTG:LTG=X-X;
P30305-X1118-G499-01-7618 4-7
4.6. Installation of MP, OMT-1 and MOD-1
MP : CP113C
05/117
BAP-0 BAP-1
B A P-1
DCC PEX
0V
blue
red
5V
06/339 06/117
4-8 P30305-X1118-G499-01-7618
4.6.2. Installation of OMT-1
If only one OMT is installed, a second one has to be installed. If OMT-1 is already connected,
check OMT features like input/output suppression and FUOMT-link.
continue
<STAT SSP;
! OMT-1 is in PLA
Connect the second OMT to IOPUNI-1 in F:PIOP(A)-1, MUT 07, plug-in position
C243 P1
P30305-X1118-G499-01-7618 4-9
/ <MOD DEVAUT: DEV=OMT-0, AUT=1, OAUT=0; If full device authorization
<MOD DEVAUT: DEV=OMT-1, AUT=1, OAUT=0; is not provided
! Check the result of the ”DISP FILE” command to see whether single files are stored
on MDD-0 or MDD-1. If so, they must be saved to MO or to the other disk.
Mount MO in MOD-0
Single file disk saving on MDD-0 or MDD-1 and creating as double file:
4-10 P30305-X1118-G499-01-7618
Installation of MOD-1 with power supply:
<DISP IOP:IOP=IOPUNI-1;
<CR MOD:MOD=1,IOP=IOPUNI-1,SCSIADDR=2;
<CONF MOD:MOD=1,OST=MBL;
<CONF MDD:MDD=1,OST=MBL;
<CONF IOP:IOP=IOPUNI-1,OST=MBL;
Screw in fuse FU 12 in Fuse Panel MUT 01 for MDD-1 and MOD-1 (7 ft racks)
<CONF IOP:IOP=IOPUNI-1,OST=ACT;
<DIAG MOD: MOD=1;
<CONF MOD:MOD=1,OST=ACT;
<CONF MDD:MDD=1,OST=ACT;
P30305-X1118-G499-01-7618 4-11
To be started early on upgrade day
The saving of the APS V11 must be executed according to “Quarterly APS Saving“.
All logfiles since the creation of the MO for database retrieval or the database retrieval itself
(REGEN / display data = database for the V17/CCNC load MO) may not be overwritten or
deleted.
If a brand new MO is used, it has to be initialized before with command:
Save the current APS V11 by procedure SW 210 in manual MMN:SW (quarterly
saving) or use project-specific command file
ATTENTION:
All new logfiles from saving of APS V11 on, must be held ready for ev. Fallback in Chapter 8.3
(Fallback from save MO V11).
The V5-link association with the DLUMODs should be displayed by using command file
”CF.11.V5CHECKG499”. The display could help in case of clearing V5-link faults after the
startup with the APS V17/CCNC.
4-12 P30305-X1118-G499-01-7618
4.9. Saving of Exchange Files APS V11
ATTENTION:
Time critical exchange files, e.g. charge files, must be saved during the Upgrade Procedure to
MO in Chapter 7.4 (note that file saving via X25-link is not possible in these chapters). All other
system- and project-specific files should be saved now.
/ <DISP FILE;
HF.<files>
SG.<files>
TM.<files>
DC.<files>
AD.<files>
etc
Note:
If the history files are saved once more, they have to be released before with command:
<REL CYCFILE:FILE=<file-name>;
Saving traffic measurement files TS., see manual OMN Chapter TR:
Active and accepted traffic measurement jobs are to be stopped and deleted,
see procedure TP-011
Saving traffic structure measurement file IA.ICTST, see manual OMN, Chapter TR:
P30305-X1118-G499-01-7618 4-13
Save CCS7 traffic structure measurement files T6., see manual OMN, Chapter TR:
/ <DISP C7TRST;
<DISP FILE:FILE=T6.;
Saving directory number observation file IA.ICDNB, see manual OMN, Chapter TR:
/ <DISP STMON;
/ <SEL MOBS;
<SEL SMOBS; S130 MOB
<DISP IAFEAT; Interrogate IA feature for meter
observation MOB
<DISP FILE:FILE=IA.; and files
4-14 P30305-X1118-G499-01-7618
Saving security files SE./SA.ACTION, OP.ACTION, PW.LOG and SJ.SECDATA if available:
/ <DISP FILE;
Mount MO in MOD-0
<RSET MO:MOD=0;
Remove MO from MOD-0
/ <DISP FILE;
Mount MO in MOD-0
<RSET MO:MOD=0;
Remove MO from MOD-0
Keep a protocol of the jobs which have to be restarted after startup in the
APS V17/CCNC.
P30305-X1118-G499-01-7618 4-15
4.10. System Status Inquiry of APS V11
! Required CP states:
4-16 P30305-X1118-G499-01-7618
! Required states:
! Required states:
P30305-X1118-G499-01-7618 4-17
Checking Alarms:
/ <DISP ALARM;
Log function:
The CSC on the CP-0 has to be created e.g. as CSC-0 if not existing:
Note: The ”CR CSC.. and MOD CSCGRP..” commands must be deleted from the logfile
Change DCP connection from IOPUNI-1 in F:PIOP(A)-1, MUT 07, plug-in pos.
C243 P2 to IOPUNI-0 in F:PIOP(A)-0, MUT 03, plug-in pos. C243 P2, if
necessary
/ <DISP CSC:CSC=X;
4-18 P30305-X1118-G499-01-7618
/ <MOD CSC:CSC=0,BAUDRATE=B9600,ADDR=1,CONNECT=MODEM,
INTERF=V24; If necessary
/ <STAT SSP;
<DISP X25LINK:X25LINK=X;
Checking X25-links.
If during the Upgrade Procedure an X25-link(s) to the SS should be available for charge file
saving, the X25-links are to be checked for redundancy. As the CP-1 (NSS) will be split off
during the procedure, there would be no access to CP-0 (SS) in case of an X25-link
connected to the NSS only.
If necessary an X25-link has to be created and the existing link switched over to CP-0.
/ <STAT SSP;
<DISP X25LINK:X25LINK=X;
P30305-X1118-G499-01-7618 4-19
4.11. Creating CP Upgrade Tables in APS V11
The Upgrade Control Table SU.UCT is created by command file ”CF.11.CRSUUCTG499”.
/ <EXEC CMDFILE:FILE=CF.11.CRSUUCTG499;
I
1
XXXXXXXXXXXXXXXXX
4-20 P30305-X1118-G499-01-7618
4.12. Changing Meter Saving Time
The meter saving point is to be put off into an uncritical time period in order to avoid impacts on
meter saving due to the upgrade.
/ <DISP METSAV;
<ENTR METSAV: TIME=08-00, CHEKNO=0; For example
P30305-X1118-G499-01-7618 4-21
4.14. Processing Logfiles
All log files since the database retrieval in V11 (REGEN and display data = database for
the V17/CCNC load- MO) must be processed and saved.
- Conversion of LG-log files from APS V11 to the new command syntax of APS V17/CCNC.
See procedure description “Database Handling V9/10/11/12/13/14/15(S)/16 to V17“ /2/.
4-22 P30305-X1118-G499-01-7618
4.14.1.2. Conversion of Log file (1) on the PC
The LG-log file (1) is saved on MO and converted on PC/Laptop, the LQ-log file (1) is saved on
MO for incorporation in APS V17/CCNC:
Mount MO in MOD-0
Mount MO in MOD-0
Convert the LG-log file (1) from V11 to V17/CCNC syntax corresponding to
procedure “Database Handling V9/10/11/12/13/14/15(S)/16 to V17” /2/
P30305-X1118-G499-01-7618 4-23
This page was left intentionally blank !
4-24 P30305-X1118-G499-01-7618
5. DETAILED DESCRIPTION PHASE 2: PROCESSOR SPLITTING
1. The processor SW-Splitting is initiated by entering the command ”SPLIT SSP”. The
CP113C is then split in an SS- and NSS- half. In the NSS the IOPMB-1 can be configured
for the activation of the CCNP-1.
In exchanges of DE-type < DE54, IOPMB-0,1 are assigned to IOC-0,1. With DE-type
DE54, the IOPMB-0,1 are assigned to IOC-2,3.
The CCNPs do not belong to the kernel of the CP (not included in the ”SPLIT SSP”
command) and have to be configured separately.
2. System halves:
CP-0: Switching System SS continues to carry out switching operations with APS V11.
If a HW fault occurs during the SW split phase in units assigned to the SS side,
the split operation is automatically interrupted and the system is merged.
CP-1: Non-Switching System NSS to install the new APS V17/CCNC. If the time
window of about 10 minutes is exceeded when entering parameters in the IPL
input mask, a startup is automatically initiated, which however has no effect on
the SS. In this case the Installation Recovery mode must be restarted by booting
BAP-1. While booting BAP-0, the auxiliary files SU.UCT and SU.UPT are deleted
and must be loaded again. During split operation, power for CP-1 units must not
be switched off, except MDD-1. With the ISTART2F of the BAP-1 the split
operation is cancelled and the APS V17/CCNC is activated.
P30305-X1118-G499-01-7618 5-1
5.2. Splitting the Processors and CCNPs
By the following ”SPLIT SSP” command only the central units are split (BAP-0,1,IOC-0,1,
CMY-0,1 and BCMY-0,1), whereas the CAPs remain on the SS.
/ <STAT SSP:UNITS=CU;
Note:
If the COMBAP command is rejected due to a hanged job, an NSTART1 must be performed.
Configuration of CCNPs:
<CONF CCNC:UNIT=CCNP-1,OST=MBL;
/ <STAT SSP:UNITS=CU;
<CONF IOC:IOC=3,OST=MBL; If DE-type is DE54 and IOC-2,3 in ACT
/ <SET SPLITOPT;
<DISP SPLITOPT; Split option is SET
5-2 P30305-X1118-G499-01-7618
Splitting the CPs:
NON-SWITCHING UNITS
--------------------------------------------------------------
BAP-1 BCMY-1 CMY-1 IOC-1 IOPMB-1
IOPMB-33 IOPMB-35 IOPMB-41 IOPMB-43 IOPUNI-1
IOPTA-1 IOPLAU-1 MDD-1 MOD-1 OMT-1
STOP;
I N I T I A L S T A R T S T O P P E D
P30305-X1118-G499-01-7618 5-3
<STAT SSP;
5-4 P30305-X1118-G499-01-7618
5.3. Loading complete APS V17/CCNC in the NSS
Prerequisites:
The completely installed APS V17/CCNC must be available on MO.
! System Message:
FORMAT;
P30305-X1118-G499-01-7618 5-5
UTI;
<LABELMD
<DISPMDDIR
5-6 P30305-X1118-G499-01-7618
<TRANSFILE
<*
<*
<*
If the APS V17/CCNC was saved on more than one MO the following message is output:
Remove first MO from MOD-1 and mount next MO with APS V17/CCNC in
MOD-1
ETX
P30305-X1118-G499-01-7618 5-7
If more MOs are available, enter “Y“:
<Y
ETX
<N
<DISPMDDIR
5-8 P30305-X1118-G499-01-7618
5.4. Installation Recovery with APS V17/CCNC in the NSS
! System Message:
FORMAT;
P30305-X1118-G499-01-7618 5-9
INS;
IOC-1;
17xxxxxx;
Note:
After the system message ”INSTALL RECOVERY INFORMATION........” the APS can be
started as follows:
<START FCP;
PLEASE ENTER USERID
<user id>
<START OM; Input command ca.15 sec after ”START FCP” execution
<START SFGSW;
<DISP TIME; Time is secure
5-10 P30305-X1118-G499-01-7618
<MOD TIME: MODE=SECURE;
Check of Q3 feature.
If Q3 is required, the parameter ”Q3ACTIVE” must be YES:
<DISP EXDDAT;
<ENTR EXDDAT: Q3ACTIVE=YES; If required YES / NO
<DISP EXDDAT;
<ENTR EXDDAT:MET=<met-type>&<met-type>....; If required
<DISP EXDDAT;
<ENTR EXDDAT:CMYSIZE=<cmysize>; If required
<DISP SSP;
! For example:
UNIT PBI MEMSIZE FIRMWARE VERSIONS DATA
PHYS APSB-PART APS PART APS PART UP-TO-
(FE)PROM FRPROM IN APS DATE
-----------------------------------------------------------------
BAP-0 0 32 32 xxxx xxxx xxxx xxxx YES
BAP-1 2 32 xxxx xxxx NO
CAP-0 4 32 xxxx xxxx NO
IOC-0 1 32 xxxx xxxx xxxx xxxx YES
IOC-1 3 xxxx xxxx NO
CMY-0 256 256 xxxx xxxx xxxx xxxx xxxx YES
CMY-1 0 256 xxxx xxxx NO
BCMY-0 xxxx xxxx xxxx xxxx YES
BCMY-1 xxxx xxxx xxxx xxxx YES
<START CSWD;
P30305-X1118-G499-01-7618 5-11
Checking the new generation files:
Checking the new generation files for correct transmission between MOD and MDD by
starting the checksum audit, which compares IMON- and MDD-checksums.
<ACT MDDAUDIT:TYPE=X;
Attention:
If the Installation Recovery is exited and the processor changes to STOP, a message is
output indicating that the Installation Recovery must be restarted using the commands
above:
<STAT SSP;
5-12 P30305-X1118-G499-01-7618
Are the states of CP units as shown above ?
Attention:
After setting the Split Option, the BAP-1 has to be booted (not RESET) and the Installation
Recovery reentered.
FORMAT;
INS;
IOC-1;
17xxxxxx;
P30305-X1118-G499-01-7618 5-13
Note:
After the system message ”INSTALL RECOVERY INFORMATION........” the APS can be
started as follows:
<START FCP;
PLEASE ENTER USERID
<user id>
PLEASE ENTER CURRENT
PASSWORD
<password>
<STAT SSP;
DE up to DE52 DE54
Attention:
If the IOPMB-1 is not in MBL now, try to configure IOPMB-1 to MBL by command. If this is
not possible, probable an APS failure exists and a fallback by merging the CP is necessary,
see Chapter 8.2.
5-14 P30305-X1118-G499-01-7618
5.5.3. Inquiry of the CCNP Status
P30305-X1118-G499-01-7618 5-15
5.5.5. Inquiry of the CCNP Status
5-16 P30305-X1118-G499-01-7618
5.5.6. Configuration of IOC-2,3 in DE-Type DE54
Attention:
For the activation of the CCNP-1 via IOPMB-1, the IOC-2 has to be configured to ACT.
The IOC-3 has to be configured to MBL, because only IOC-2,3 in status out of PLA are
activated during the startup.
IOC-2,3 as well as CAPs are in status SPL, if they were already configured from PLA to MBL
before the last recovery.
<STAT SSP:UNITS=CU;
<STAT SSP:UNITS=CU;
P30305-X1118-G499-01-7618 5-17
5.6. Preparation of both APS V11 and V17/CCNC
<STAT SSP;
! MOD-1 in ACT
<DISP METSAV;
Note:
See following chapters for output of system messages during start of the processes.
5-18 P30305-X1118-G499-01-7618
5.6.3. Creating and Checking Files in the NSS
SUBSCRIBER CHARGING
TOLL FREE SERVICE CHARGING
etc
If CA files are not available, enter the corresponding ”SAVE MET:TYPE..” command for each
existing meter type. If this command will be rejected with the message:
”MML-COMMAND NOT ALLOWED IN ACTUAL STATE”
then first enter command ”<SAVE MET: FUNC= FALLBACK;”
! CA files available
P30305-X1118-G499-01-7618 5-19
5.6.3.2. Creating IA Files
If no IA files are available, the following message is displayed on the OMT-1 during start of
the processes and creation of the IA files, when the corresponding IA feature is already
activated in V17/CCNC:
! IA files available
If IA files are not available, enter the corresponding ”ACT IAFEAT..” command:
<ACT IAFEAT:TYPE=DNB,SIZE=<size>; ”
<ACT IAFEAT:TYPE=ERST,SIZE=<size>; ”
<ACT IAFEAT:TYPE=FIR,SIZE=<size>; ”
<ACT IAFEAT:TYPE=IARA,SIZE=<size>; ”
<ACT IAFEAT:TYPE=INA,SIZE=<size>; ”
<ACT IAFEAT:TYPE=MAL,SIZE=<size>; ”
<ACT IAFEAT:TYPE=MOB,SIZE=<size>; ”
<ACT IAFEAT:TYPE=TOB,SIZE=<size>; ”
<ACT IAFEAT:TYPE=TST,SIZE=<size>; ”
<ACT IAFEAT:TYPE=<type>,SIZE=<size>; ”
! IA files available
5-20 P30305-X1118-G499-01-7618
5.6.3.3. Starting IACHASTA Registration
IACHASTA-Metering
Registration of summation data link call number or call duration and storing on meters
separately for each traffic relation (new files CA.IC.UCHA and CA.IR.rnnns.fffff).
IACHASTA-AMA
Grouping the call data individually for each call and generating a AMA data record (new
file IA.ICIAR).
<DISP FILE:FILE=SE.;
<DISP FILE:FILE=SA.;
<DISP FILE:FILE=SJ.;
<DISP FILE:FILE=OP.;
<DISP FILE:FILE=PW.;
P30305-X1118-G499-01-7618 5-21
5.6.4. Changing Meter Saving Time in the NSS
The meter saving point is to be put off into an uncritical time period in order to avoid impacts
on meter saving due to the upgrade.
<DISP METSAV;
<ENTR METSAV: TIME=08-00, CHEKNO=0; For example
<DISP METADM;
<DISP METADM;
! The meter administration data in the SS V11 and NSS V17/CCNC must be
identical
<ENTR METADM:DPATCH=<xxxx>,BOOKOF=<yyyy>;
<ENTR METADM:TYPE=METSUB,DNSUP=NOTCONN&METPDN&DEB;
<ENTR METADM:TYPE=METTFS,ACNOPR=130;
<ENTR METADM:TYPE=METSUB,FORMAT=2,CNTRTHR=999999-2;
<DISP SSPRT;
<INHIB SSPRT; If routine tests are globally
allowed
5-22 P30305-X1118-G499-01-7618
5.6.6.2. Deactivation of Routine Tests in the SS
The routine tests have to be blocked temporarily in APS V11.
<DISP SSPRT;
<INHIB SSPRT;
If routine tests are globally
allowed
<DISP FILE:FILE=SU.;
<EXEC CMDFILE:FILE=CF.17.CRSUUCTG499;
I
1
XXXXXXXXXXXXXXXXX
P30305-X1118-G499-01-7618 5-23
5.6.8. Expansion of the File SG.OPER in the NSS
To ensure that in case of failure the history file is not overwritten, file SG.OPER will be
expanded with command file ”CF.17.OPERMAXG499”, if it’s size is less than 1800.
<DISP FILE:FILE=SG.OPER,ALL;
<EXEC CMDFILE:FILE=CF.17.OPERMAXG499; If SG.OPER is available and size < 1800
<DISP ALARM:OBJECT=LNLCKOUT;
<STAT SUB:LAC=X,DN=X,LNSTAT=ECSPA; If alarms exist with ”CLASS=ECSL”
5-24 P30305-X1118-G499-01-7618
5.6.10. Incorporating the Logfile (1) in the NSS
LG-logfile (1) and LQ-logfile (1) available since last database retrieval must be incorporated.
Load LG-logfile (1), LQ-logfile (1) and the masterlogfile from the database conversion:
P30305-X1118-G499-01-7618 5-25
5.6.10.1. IOC-2,3 and CAP Status Request in the NSS
In the Installation Recovery and Split mode the status request of IOC-2,3 and CAPs does not
indicate the actual status. For this purpose a display of the semipermanent status table is
required.
<EXEC CMDFILE:FILE=CF.17.HEXIOCAG499;
IOC-2 IOC-3
Yy zz
H´00 H´01
PLA Not
equal
PLA
! Check if available CAPs and IOC-2,3 have correct status ”Not equal PLA” and
configure to MBL if necessary
<STAT SSP:UNITS=CU;
<CONF CAP:CAP=<cap-no>,OST=MBL; If CAPs in PLA or UNA, configure all available CAPs
5-26 P30305-X1118-G499-01-7618
5.6.10.2. Status Requests
<STAT LTG:LTG=X-X;
<DISP LTG:LTG=X-X;
Inquiry of the actual LTG status in the NSS with APS V17/CCNC:
<DISP LTG:LTG=X-X;
P30305-X1118-G499-01-7618 5-27
! OFFSET CONTENT HEX
----------+----------------------------------------
MBUL 0-0 MBUL 0-1 MBUL 0-2 MBUL 0-3
H´00000000 07xx... 07xx... 07xx... 07xx...
MBUL 0-4 MBUL 0-5 MBUL 0-6 MBUL 0-7
H´00000010 07xx... 07xx... 07xx... 07xx...
- - - - - - - - - - - - - - - - - - - - - - - - - - - -
H´00000020 07xx... 07xx... 07xx... 07xx...
H´00000030 07xx... 07xx... 07xx... 07xx...
H´00000040 07xx... 07xx... 07xx... 07xx...
H´00000050 07xx... 07xx... 07xx... 07xx...
H´00000060 07xx... 07xx... 07xx... 07xx...
H´00000070 07xx... 07xx... 07xx... 07xx...
- - - - - - - - - - - - - - - - - - - - - - - - - - - -
MBUL 1-0 MBUL 1-1 MBUL 1-2 MBUL 1-3
H´00000080 07xx... 07xx... 07xx... 07xx...
MBUL 1-4 MBUL 1-5 MBUL 1-6 MBUL 1-7
H´00000090 07xx... 07xx... 07xx... 07xx...
- - - - - - - - - - - - - - - - - - - - - - - - - - - -
H´000000A0 07xx... 07xx... 07xx... 07xx...
H´000000B0 07xx... 07xx... 07xx... 07xx...
H´000000C0 07xx... 07xx... 07xx... 07xx...
H´000000D0 07xx... 07xx... 07xx... 07xx...
H´000000E0 07xx... 07xx... 07xx... 07xx...
H´000000F0 07xx... 07xx... 07xx... 07xx...
- - - - - - - - - - - - - - - - - - - - - - - - - - - -
MBUS 0-0 MBUS 0-1 MBUS 0-2 MBUS 0-3
H´00000100 07xx... 07xx... 07xx... 07xx...
- - - - - - - - - - - - - - - - - - - - - - - - - - - -
H´00000110 07xx... 07xx... 07xx... 07xx...
H´00000120 07xx... 07xx... 07xx... 07xx...
H´00000130 07xx... 07xx... 07xx... 07xx...
- - - - - - - - - - - - - - - - - - - - - - - - - - - -
MBUS 1-0 MBUS 1-1 MBUS 1-2 MBUS 1-3
H´00000140 07xx... 07xx... 07xx... 07xx...
H'00 = UNA H’01 = CBL H’02 = NAC H’03 = SEZ H'04 = STB
H’05 = ACT H’06 = RES (ACT) H’07 = PLA H’08 = MBL
! The status of all MB units MBUL and MBUS must be PLA = 07 or ACT = 06.
Units in MBL = 08 must be configured to PLA = 07.
5-28 P30305-X1118-G499-01-7618
Attention: If LTGs are in MBL, it is not possible to configure the corresponding MBUL/TSG
from MBL to PLA.
<DISP MB;
! MBTYPE = MBB
<MOD MB:MB=X,MBTYPE=MBD,ALPROF=CRITICAL;
<DISP MB;
! MB MBTYPE NUMMBIA ALPROF
--+------+-------+--------
0 MBD 0 CRITICAL
1 MBD 0 CRITICAL
<STAT MB;
! MBIC - 0 in MBL
MBIH - 0-0 in MBL
MBIH - 0-1 in MBL
MBIC - 1 in MBL
MBIH - 1-0 in MBL
MBIH - 1-1 in MBL
P30305-X1118-G499-01-7618 5-29
5.6.10.2.4. MB(D) Status Requests in the NSS
In the Installation Recovery mode the status request “STAT MB/SN“ does not indicate the
actual MB/SN status. For this purpose a display of the semipermanent MB/SN status table is
required.
Inquiry of the actual MB(D) status in the NSS with new APS V17/CCNC:
5-30 P30305-X1118-G499-01-7618
Byte 0 => operational status of MBIH:
H'00 = UNA H’01 = CBL H’02 = NAC H’03 = SEZ H'04 = STB
H’06 = ACT H’07 = PLA H’08 = MBL
Note:
If LTGs are in MBL, it is not possible to configure the corresponding MBIH/TSG from
MBL to PLA.
P30305-X1118-G499-01-7618 5-31
Table of hex values and the corresponding SN states:
H'00 = UNA H’01 = CBL H’02 = NAC H’03 = SEZ H'04 = STB
H’06 = ACT H’07 = PLA H’08 = MBL
! The status of all SN units TSG and SSG must be “PLA“ = 07 or “ACT“ = 06.
If the status is “MBL“ = 08, the TSG/SSGs must be configured to “PLA“ =
07
Note:
If LTGs are in MBL, it is not possible to configure the corresponding TSG/MBIH from MBL
to PLA.
5-32 P30305-X1118-G499-01-7618
5.6.11. Setting the Upgrade Flag in the NSS
By setting the upgrade flag the processes IOAPR, LUMPR and SUMPR are started and file
SU.UPT is created. This way the system is informed that an ISTART2F upgrade will be
executed.
<START SYSUPG;
<DISP FILE:FILE=SU.;
<STAT SSP;
<DISP FILETRF:JN=X; If no transmission is in progress
<EXEC CMDFILE:FILE=CF.11.PLACSCG499; deactivate all CSC-links
Note:
Ignore error messages for not accessible (status SPL) or not created CSC-links.
P30305-X1118-G499-01-7618 5-33
5.7.2. Deactivation of X25-Links
Deactivating all existing X25-links:
This is done with command file ”CF.11.PLAX25G499” which configures X25-link-0...7 to
status PLA.
Note:
Ignore error messages for not accessible or not created X25-links.
Before the current logfile is closed, SCI’s have to be blocked by entering patch ”B2925L2Z”.
5-34 P30305-X1118-G499-01-7618
5.9.2. Saving and Converting of Logfile (2) / Dest. APS V17/CCNC
The LG-log file (2) is saved on MO and converted on PC/Laptop, the LQ-log file (2) is saved
on MO for incorporation in APS V17/CCNC:
Mount MO in MOD-0
Remove MO from MOD-0 and hold it ready for incorporation of the LQ-log
file in APS V17/CCNC.
Mount MO in MOD-0
Convert the LG-log file (1) from V11 to V17/CCNC syntax, corresponding to
procedure “Database Handling V9/10/11/12/13/14/15(S)/V16 to V17 “ /2/
P30305-X1118-G499-01-7618 5-35
5.10. Incorporating Log file (2) in the NSS
Note:
The logfiles available since the processing of logfile (1) must be incorporated.
Load LG-logfile (2), LQ-logfile (2) and the masterlogfile from the database conversion:
5-36 P30305-X1118-G499-01-7618
Incorporate LG-logfile (2) and if Q3 is active the LQ-logfile (2):
<DISP UPGRDOPT;
<SET UPGRDOPT:BLKSCI=YES;
<EXEC CMDFILE:FILE=CF.11.UPDFILEG499;
P30305-X1118-G499-01-7618 5-37
This page was left intentionally blank!
5-38 P30305-X1118-G499-01-7618
6. DETAILED DESCRIPTION PHASE 3: CUT OVER
o If any deficiencies occur during the Recovery, reloading of LTGs, MCH errors etc.
please save file SG.OPER and MLOG in V11 and V17/CCNC and send them to Vienna
together with an error message.
6.2. Startup and Change over from APS V11 to APS V17/CCNC
<RSET SPLITOPT;
<DISP SPLITOPT; Split option is RESET
<END INSTALL;
P30305-X1118-G499-01-7618 6-1
! System messages:
6-2 P30305-X1118-G499-01-7618
DATE : xx-xx-xx
TIME : xx:xx:xx
UNIT : BAPM
MEMORY INITIALIZED
PERIPHERY RELOADED WITH CODE AND DATA
APS GENERATION : 17xxxxxx
P30305-X1118-G499-01-7618 6-3
6.3. Restoring System Redundancy
/ <STAT SSP;
PLEASE ENTER USERID
<user id>
<STAT CCG;
<DISP CCG;
/ <RSET SPLITOPT;
6-4 P30305-X1118-G499-01-7618
6.4.2. Diagnosis of the MB
/ <STAT MB;
<STAT SN;
<STAT CCNC: UNIT=MUXM-X;
<STAT LTG: LTG=X-X;
! MB-0 and MB-1 in ACT Configure MB if necessary
SN-0 in ACT or STB, SN-1 in STB or ACT Configure SN if necessary
MUXM-0,1 and MUXM-10,11 in ACT or PLA Configure MUXM if necessary
All LTG MCH’s in ACT/STB Clear faults if necessary
/ <CONF CCNC:UNIT=CCNP-0,OST=STB;
<STAT CCNC:UNIT=CCNP-X;
P30305-X1118-G499-01-7618 6-5
6.4.5. Checking SYP, TIME and NUCs/IPNUCs
Note:
It is possible that some IPNUC are in status UNA. These IPNUC have to be deactivated and
activated.
6-6 P30305-X1118-G499-01-7618
6.4.6. Interrogation of Alarms from Emergency Call Station Party
Note:
To be executed only, if alarms were found in Chapter 5.6.9
With the command ”STAT SUB: LAC=X, DN=X, LNSTAT=ECSPA” the relevant ports were
noted. These ports have to be configured now.
/ <DISP IAFEAT;
<DISP FILE:FILE=IA.;
/ <DISP IAFEAT;
<DISP IACRG;
<DISP FILE:FILE=IA.;
<DISP FILE:FILE=CA.;
Check CA files:
/ <DISP EXDDAT;
<DISP FILE:FILE=CA.;
P30305-X1118-G499-01-7618 6-7
6.4.8. Restoring original Meter Saving Points
If meter saving has been shifted to a time-uncritical point, the original value has to be
restored.
/ <DISP METSAV;
<ENTR METSAV:TIME=<hh-mm>,CHEKNO=<no>; See original value
Inquiry of system status APS V17 with the command file ”CF.17.SYSTATG499”:
The switching equipment must be checked in accordance with the prepared concept.
In case of faults, a decision must be made whether a fallback to the APS V11 is to be
initiated.
6-8 P30305-X1118-G499-01-7618
7. DETAILED DESCRIPTION PHASE 4: POST PROCESSING
/ <SET UPGRDOPT:BLKSCI=NO,OPSTAT=SPECIAL2;
<DISP UPGRDOPT;
If ALIAS names exist in the old APS they have to be re-entered in the APS V17/CCNC:
/ <DISP ALIAS:ALIAS=X;
<ENTR ALIAS:FILE=<file-name>,ALIAS=<alias-name>;
Note:
To be executed only if command file “<exchid>.DB.UPD“ and / or "CF.LG.17.UPD" exists
from APS database installation.
If the APS V17/CCNC has been installed in an exchange with CP in Split Mode, some
commands such as “CR X25LINK“ or “CR X25ROUTE“ could not be executed. The
database has to be completed now by starting the command file “<exchid>.DB.UPD“ and /
or "CF.LG.17.UPD" if available on disk.
P30305-X1118-G499-01-7618 7-1
7.3. Activating Links
/ <DISP CSC:CSC=X;
<STAT SSP;
7-2 P30305-X1118-G499-01-7618
7.3.2. Activating X25-Links
The X25-links are activated by command file ”CF.17.ACTX25G499” for X25-link 0....7.
/ <STAT SSP;
/ <EXEC CMDFILE:FILE=CF.17.ACTX25G499;
<STAT SSP;
7.4.1. CP SW-Splitting
The CP113C is divided into two system halves
CP-0: Non-Switching System NSS is used for file handling with APS V11
CP-1: Switching System SS continues to carry out switching operations with
APS V17/CCNC
/ <STAT SSP;
Note:
If the COMBAP command is rejected due to a hanged job, an NSTART1 must be performed.
P30305-X1118-G499-01-7618 7-3
<SPLIT SSP: TEST=N, SUP=Y, APSCHG=N;
NON-SWITCHING UNITS
--------------------------------------------------------------
BAP-0 BCMY-0 CMY-0 IOC-0 IOPMB-0
IOPMB-32 IOPMB-34 IOPMB-40 IOPMB-42 IOPUNI-0
IOPTA-0 IOPLAU-0 MDD-0 MOD-0 OMT-0
CSC-0
FORMAT;
7-4 P30305-X1118-G499-01-7618
INS;
11xxxxxx;
Note:
After the system message ”INSTALL RECOVERY INFORMATION......” the APS can be
started as follows:
<START FCP;
<user id>
<password>
Attention:
If the Installation Recovery is exited and the processor changes to STOP, a message is
output indicating that the Installation Recovery must be restarted using the commands
above:
P30305-X1118-G499-01-7618 7-5
7.4.3. Starting Processes in the NSS
<DISP METSAV;
Note:
If files are empty, the message ERROR: FILE L FC 33 is output.
The command files should not release the IA files after the saving process (no
REL CYCFILE), so that the files can be continued in the event of a fallback from MDD-0.
Mount MO in MOD-0
7-6 P30305-X1118-G499-01-7618
7.4.4.2. Saving File IA.ICMAL
Save file IA.ICMAL, using the following procedure or project-specific command file.
Mount MO in MOD-0
Mount MO in MOD-0
P30305-X1118-G499-01-7618 7-7
7.4.4.4. Saving File IA.ICIAR
Save file IA.ICIAR (IACHASTA-AMA registration) using the following procedure, see also
OMN:EXCH-TA, TP-233, or project-specific command file.
Mount MO in MOD-0
Mount MO in MOD-0
7-8 P30305-X1118-G499-01-7618
7.4.4.6. Saving File IA.ICINA
Save file IA.ICINA using the following procedure, see also OMN:EXCH-TA, TP-233, or
project-specific command file.
Mount MO in MOD-0
Mount MO in MOD-0
P30305-X1118-G499-01-7618 7-9
7.4.5. Saving IACHASTA Files in the NSS
All available IACHASTA files CA.IR. must be saved for postprocessing.
Mount MO in MOD-0
<EDIT MET:TYPE=IACMET;
<DISP FILE;
Mount MO in MOD-0
7-10 P30305-X1118-G499-01-7618
7.4.7. Saving CA Files for Meter Accounting in the NSS
Statistic- and Trunkmeters in the files CA.ST.UCHA and CA.TR.UCHA have to be saved for
post-processing as account files.
Subscribermeters in the files CA.SU.UCHA and CA.TF.UCHA may be saved as account files
too, but they can also be saved as regeneration files for regeneration of meters in the new
APS.
Mount MO in MOD-0
Print out some meters count for spot checks after meter regeneration:
<DISP MET:TYPE=METSUB,DN=<dn-number>&&<dn-number>,LAC=X;
or
<DISP MET:TYPE=METSUB,DN=X,LAC=X;
<STOP DISP:JN=<job-no>;
<DISP MET:TYPE=METTFS,SDN=<sdn-number>;
Mount MO in MOD-0
P30305-X1118-G499-01-7618 7-11
<STAT SSP; MOD-0 in ACT
/ <STAT SSP;
<SAVE MET;
<SAVE MET;
7-12 P30305-X1118-G499-01-7618
Comparing regenerated meter readings:
/ <DISP MET:TYPE=METSUB,DN=<dn-number>&&<dn-number>,LAC=X;
or
<DISP MET:TYPE=METSUB,DN=X,LAC=X;
<STOP DISP:JN=<job-no>;
Note:
Additional meters may exist in APS V17/CCNC after the activation of the call processing
P30305-X1118-G499-01-7618 7-13
7.6. Reduction of File SG.OPER
If file SG.OPER was expanded, it has to be saved and recreated with the original size using
command file ”CF.17.OPERMING499”.
Mount MO in MOD-0
<DMP SGMSG;
/ <EXEC CMDFILE:FILE=CF.17.OPERMING499;
7-14 P30305-X1118-G499-01-7618
7.7.2. Deleting Logfiles
/ <DISP GEN;
<CAN GEN:GEN=<non-actual generations>;
/ <ALLOW SSPRT;
<INHIB SSPRT: TESTID=<x>; <x> = not available CP-units
Start jobs for traffic measurement, traffic structure, time jobs, command
time jobs etc
P30305-X1118-G499-01-7618 7-15
7.10. Activating the MDD-0 (after 24h observation period)
Attention:
After activating the MDD-0, an eventual fallback can only be carried out by loading APS V11
from the save MO.
/ <DISP MDDAUDIT;
<MOD MDDAUDIT: LOCKSTAT=UNLOCKED,TYPE=X; If MDD audit is locked
<CONF MDD:MDD=0,OST=MBL;
<DIAG MDD:MDD=0;
<CONF MDD:MDD=0, OST=ACT;
Unplug the OMT-1 from IOPUNI-1 in F:PIOP(A)-1, MUT 07, plug-in position
C243 P1
7-16 P30305-X1118-G499-01-7618
7.11.3. Removing the MOD-1
The MOD-1 installed for the upgrade only, has to be removed.
/ <STAT SSP;
<CONF MDD:MDD=1,OST=MBL;
<CONF MOD: MOD=1,OST=MBL;
<CONF MOD:MOD=1,OST=PLA;
<CONF IOP:IOP=IOPUNI-1,OST=MBL;
Switch off power supply for MDD-1 and MOD-1 MDD-1 power supply should be
already switched off
Unscrew fuse FU 33 in fuse panel MUT 01 for MDD-1 and MOD-1 (8ft racks)
Unscrew fuse FU 12 in Fuse Panel MUT 01 for MDD-1 and MOD-1 (7ft racks)
<CONF IOP:IOP=IOPUNI-1,OST=ACT;
<CONF MDD: MDD=1, OST=ACT;
P30305-X1118-G499-01-7618 7-17
7.12. Saving of APS V17/CCNC
E N D OF U P G R A D E P R O C E D U R E
7-18 P30305-X1118-G499-01-7618
8. INTERRUPTING THE UPGRADE PROCEDURE
Attention:
Before falling back inform the emergency service in Munich (depending on type of faults)
and save all history files to MO.
P30305-X1118-G499-01-7618 8-1
8.2. Fallback Procedure 1: Fallback from Installation Recovery
Initial position:
The procedure has to be interrupted because after starting the Installation Recovery the APS
V17/CCNC shows deficiencies which do not allow the continuation of the Upgrade
Procedure.
This fallback is realized by merging NSS and SS to the original system without system
interruption.
<MERGE SSP:DIAG=N;
/ <STAT SSP;
/ <CONF MDD:MDD=1,OST=MBL;
<CONF IOC:IOC=3,OST=ACT; If DE-type is DE54
8-2 P30305-X1118-G499-01-7618
8.2.3. Resetting the Split Option
/ <RSET SPLITOPT;
/ <DACT SYSUPG;
<DISP FILE:FILE=SU.;
P30305-X1118-G499-01-7618 8-3
8.2.6. Restoring original Time for Meter Saving
/ <STAT LOG;
<SET LOG:FILE=<file-name>,SIZE=<size>; If not activated
/ <STAT SSP;
/ <EXEC CMDFILE:FILE=CF.11.ACTCSCG499;
<CONF CSC: CSC=<csc-no>,OST=MBL; Configure CSC-link, if created
in Chapter 4.10
<CONF CSC: CSC=<csc-no>,OST=PLA;
<STAT SSP;
8-4 P30305-X1118-G499-01-7618
8.2.8.2. Activating the X25 Links
The X25-links can be activated by command file ”CF.11.ACTX25G499” for X25LINK-0.. 7 if
they are in status PLA.
/ <STAT SSP;
/ <EXEC CMDFILE:FILE=CF.11.ACTX25G499;
<STAT SSP;
/ <DISP JOB;
<DISP TJOB;
etc
Start jobs for traffic measurement, traffic structure, time jobs, command
time jobs
/ <ALLOW SSPRT;
<INHIB SSPRT: TESTID=<x>; <x> = not available CP-units
! Full redundancy
P30305-X1118-G499-01-7618 8-5
8.2.12. Deleting auxiliary Files
Unplug the OMT-1 from IOPUNI-1 in F:PIOP(A)-1, MUT 07, plug-in position
C243 P1
/ <STAT SSP;
<CONF MOD:MOD=1,OST=MBL;
<CONF MOD:MOD=1,OST=PLA;
<CONF MDD: MDD=1, OST=MBL;
<CONF IOP:IOP=IOPUNI-1,OST=MBL;
8-6 P30305-X1118-G499-01-7618
Switch off power supply for MDD-1 and MOD-1
<CONF IOP:IOP=IOPUNI-1,OST=ACT;
<DIAG MDD: MDD=1;
<CONF MDD: MDD=1, OST=ACT;
P30305-X1118-G499-01-7618 8-7
8.3. Fallback Procedure 2: Fallback from MDD-1 with V11
Initial position:
This fallback is performed if after the successful startup and change over to APS V17/CCNC
the first checks of switching operations reveal deficiencies.
Fallback:
ISTART2F with APS V11from disk MDD-0 after preparation of APS V11 in the Installation
Recovery. E.g. MB and SN are configured to PLA, so the LTGs can be loaded via 2 MCHs
(MB-0 and SN-0 are in MBL before).
Press BOOT key on BCMY-1 and wait for display A925 on the MP
Switch on power to MDD-0 APS V11,if switched off and wait 30 sec for
MDD runup
FORMAT;
INS;
8-8 P30305-X1118-G499-01-7618
IOC-0;
11xxxxxx;
Note:
After the system message ”INSTALL RECOVERY INFORMATION........” the APS can be
started as follows:
<password> <password>
<START FCP;
<START OM; Input command ca. 15 sec after ”START FCP” execution
<START SFGSW;
<START CSWD;
P30305-X1118-G499-01-7618 8-9
8.3.3. Resetting the Split Option
<RSET SPLITOPT;
<EXEC CMDFILE:FILE=CF.11.MBSNPLA1;
<CONF MDD:MDD=0,OST=MBL;
<END INSTALL;
8-10 P30305-X1118-G499-01-7618
8.3.7. Quick Check of APS V11
<STAT SSP;
<CONF SYP:OST=ACT;
P30305-X1118-G499-01-7618 8-11
8.3.9. Activating the CCNP-1
/ <STAT SSP;
! MDD-1 in MBL
/ <DISP MDDAUDIT;
<MOD MDDAUDIT: LOCKSTAT=UNLOCKED,TYPE=X; If MDD audit is locked
8-12 P30305-X1118-G499-01-7618
8.3.12. Setting the LOG Function
/ <STAT LOG;
<SET LOG: FILE=<file-name>,SIZE=24; If not activated
/ <STAT SSP;
Change DCP connection fom IOPUNI-0 in F:PIOP(A)-0, MUT 07, plug-in pos.
C243 P2 to IOPUNI-1 in F:PIOP(A)-1, MUT 03, plug-in pos. C243 P2, if changed in
Chapter 4.10
/ <EXEC CMDFILE:FILE=CF.11.ACTCSC;
<STAT SSP;
! All available CSC-links activated
/ <STAT SSP;
P30305-X1118-G499-01-7618 8-13
/ <EXEC CMDFILE:FILE=CF.11.ACTX25;
<STAT SSP;
! All available X25-links activated
<DISP JOB;
<DISP TJOB;
etc
/ <ALLOW SSPRT;
<INHIB SSPRT: TESTID=<x>; <x> = not available CP-units
! Full redundancy
8-14 P30305-X1118-G499-01-7618
8.3.18. Removing the MP
Unplug the OMT-0 from IOPUNI-0 in F:PIOP(A)-0, MUT 07, plug-in position
C243 P1
/ <STAT SSP;
<CONF MOD:MOD=0,OST=MBL;
<CONF MOD:MOD=0,OST=PLA;
<CONF MDD:MDD=0,OST=MBL;
<CONF IOP:IOP=IOPUNI-0,OST=MBL;
Unscrew fuse FU 33 in fuse panel MUT 01 for MDD-1 and MOD-1 (8 ft racks)
Unscrew fuse FU 12 in Fuse Panel MUT 01 for MDD-1 and MOD-1 (7 ft racks)
P30305-X1118-G499-01-7618 8-15
Screw in fuse FU 33 in fuse panel MUT 01 for MDD-0 (8 ft racks)
Screw in fuse FU 33 in fuse panel MUT 01 for MDD-0 (8 ft racks)
Screw in fuse FU 33 in Fuse Panel MUT 01 for MDD-1 (7 ft racks)
Switch on power supply for MDD-0 Wait 30 sec for MDD runup
<CONF IOP:IOP=IOPUNI-0,OST=ACT;
8-16 P30305-X1118-G499-01-7618
8.4. Fallback Procedure 3: Fallback from save MO V11
Initial position:
This fallback is performed, when the system is merged and the new APS V17/CCNC reveal
serious faults after a longer period in service. In this case, that both MDDs are active with
APS V17/CCNC, a fallback can only be carried out from the last APS V11 save MO produced
in Chapter 4.7.
MDD-0: power is on, status ACT MDD-1: power is on, status ACT
MDD-0: available APS: V17/CCNC MDD-1: available APS : V17/CCNC
/ <SET UPGRDOPT:BLKSCI=YES;
/ <EXEC CMDFILE:FILE=CF.17.PLAX25G499;
/ <EXEC CMDFILE:FILE=CF.17.PLACSCG499;
P30305-X1118-G499-01-7618 8-17
8.4.4. Saving Charge Files to Disks
/ <EXEC CMDFILE:FILE=CF.17.UPDFILEG499;
/ <DISP FILE:FILE=CA.;
Mount MO in MOD-0
<MOD LOGFILE: FILE=<new log file>,SIZE=24; Close current log file and open
new log file
<DISP FILETEXT:FILE=LG.<terminated log file>.A1; Display terminated LG-log file
for entries
8-18 P30305-X1118-G499-01-7618
Save the terminated LG-log file together with the LQ-log file for incorporation in V11:
Mount MO in MOD-0
Press BOOT key on BCMY-0 and wait for display A925 on the MP
STOP;
I N I T I A L S T A R T S T O P P E D
P30305-X1118-G499-01-7618 8-19
8.4.8. Loading APS V11
FORMAT;
UTI;
MOD;
8-20 P30305-X1118-G499-01-7618
010C23 (MOD-0, CP113C)
<LABELMD
<DISPMDDIR
P30305-X1118-G499-01-7618 8-21
<TRANSFILE
<*
<*
<*
If the APS V11 was saved on more than one MO the following message appears:
Remove first MO from MOD-0 and mount next MO with APS V11 in MOD-0
ETX
8-22 P30305-X1118-G499-01-7618
If more MOs are available, in this case the MO with the CA meter files saved in Chapter
8.4.5, enter ”Y”:
<Y
ETX
<N
<DISPMDDIR
P30305-X1118-G499-01-7618 8-23
8.4.9. Manual Startup with APS V11
FORMAT;
MAN;
IOC-0;
11xxxxxx;
FORCED;
8-24 P30305-X1118-G499-01-7618
8.4.10. Quick Check
/ <STAT SSP;
<user id>
<password>
/ <CONF BAP:BAP=1,OST=MBL;
<CONF BAP:BAP=1,OST=ACT;
P30305-X1118-G499-01-7618 8-25
8.4.12. Configuration of MDD-1
/ <CONF MDD:MDD=1,OST=MBL;
<CONF MDD:MDD=1,OST=PLA;
Transfer all LG- and LQ-log files from APS V11 and V17/CCNC:
8-26 P30305-X1118-G499-01-7618
Incorporate all log files from APS V11 and V17/CCNC:
/ <DISP FILE:FILE=LG.;
<DISP FILE:FILE=LQ.; If Q3 is active
<EXEC CMDFILE: FILE=LG.<log file>.A1,CHOL=Y; Syntax check for each LG-log
file available from V11 and
V17/CCNC
<ACT IAOPT: BLBUFR=ADMREC;
<SET UPDATE: STATUS=SIMUL;
Attention:
Incorporate log files in the correct sequence, e.g. first V11 log file (1), log file (2)
and at least the V17/CCNC log file
P30305-X1118-G499-01-7618 8-27
8.4.14. File Handling
8.4.14.1. CP SW-Splitting
/ <STAT SSP;
Note:
If the COMBAP command is rejected due to a hanged job, an NSTART1 must be performed.
8-28 P30305-X1118-G499-01-7618
8.4.14.2. Installation Recovery with APS V17/CCNC
The IPL Menu appears on OMT-1 after CP-split:
FORMAT;
INS;
IOC-1;
17xxxxxx;
Note:
After the system message ”INSTALL RECOVERY INFORMATION........” the APS can be
started as follows:
<START FCP;
<user id>
<password>
P30305-X1118-G499-01-7618 8-29
<START OM; Input command ca. 15 sec after
”START FCP” execution
<START SFGSW;
<DISP TIME; Time is secure
<START CSWD;
<DISP METSAV;
Note:
If files are empty, the message ERROR: FILE L FC 33 is output.
The command files should not release the IA files after the saving process (no REL
CYCFILE), so that the files can be continued in the event of a fallback from MDD-1.
8-30 P30305-X1118-G499-01-7618
8.4.14.4.1. Saving File IA.ICAMA
Save file IA.ICAMA, using the following procedure, see also OMN:EXCH-TA, TP-233, or
project-specific command file.
Mount MO in MOD-1
Mount MO in MOD-1
P30305-X1118-G499-01-7618 8-31
8.4.14.4.3. Saving File IA.ICMOB and IA.ICFIR
Save files IA.ICMOB and IA.ICFIR, using the following procedure or project-specific
command file.
Mount MO in MOD-1
Mount MO in MOD-1
8-32 P30305-X1118-G499-01-7618
8.4.14.4.5. Saving Files IA.ICIAR1 and IA.ICIAR2
Save files IA.ICIAR1 and IA.ICIAR2 using the following procedure, see also OMN:EXCH-TA,
TP-233, or project-specific command file.
Mount MO in MOD-1
Mount MO in MOD-1
P30305-X1118-G499-01-7618 8-33
8.4.14.4.7. Saving File IA.IC<type>
Save any other file IA.IC<type>, using the following procedure or project-specific command
file.
Mount MO in MOD-1
Mount MO in MOD-1
<EDIT MET:TYPE=IACMET;
8-34 P30305-X1118-G499-01-7618
8.4.14.5. Saving Security Files in the NSS
Save security files SE./SA.ACTION, OP.ACTION, PW.LOG and SJ.SECDATA if necessary.
<DISP FILE;
Mount MO in MOD-1
/ <STAT SSP;
P30305-X1118-G499-01-7618 8-35
8.4.15. Removing MOD-1
The MOD-1 installed for the upgrade only and still connected, has to be removed.
/ <STAT SSP;
<CONF MOD:MOD=1,OST=MBL;
<CONF MOD:MOD=1,OST=PLA;
<CONF MDD: MDD=1, OST=MBL;
<CONF IOP:IOP=IOPUNI-1,OST=MBL;
Switch off power supply for MDD-1 and MOD-1 MDD-1 power supply should be
already switched off
Unscrew fuse FU 33 in fuse panel MUT 01 for MDD-1 and MOD-1 (8 ft racks)
Unscrew fuse FU 12 in Fuse Panel MUT 01 for MDD-1 and MOD-1 (7 ft racks)
<CONF IOP:IOP=IOPUNI-1,OST=ACT;
<DIAG MDD: MDD=1;
<CONF MDD: MDD=1, OST=ACT;
8-36 P30305-X1118-G499-01-7618
8.4.16. Removing the MP
Unplug the OMT-1 from IOPUNI-1 in F:PIOP(A)-1, MUT 07, plug-in position
C243 P1
P30305-X1118-G499-01-7618 8-37
8.5. Double Disk Failure
If a double disk failure should occur in the switching system SS during CP SW-Split, proceed
as follows.
! Message:
THE ACTUAL GENERATION xxxxxxxx WITH THE CREATION DATE YY-MM-DD HH-
MM-SS IS VALID AND COMPLETE ON THE DISK TO BE ACTIVATED.
PLEASE ENTER:
<STOP MDDACT; or
<CONT MDDACT: LABEL; or
<CONT MDDACT;
continue
<CONT MDDACT;
<UPD GEN;
<UPD VSD (if available)
<MOD LOGFILE: FILE=LOG<x+1>, ERASE=YES, SIZE=24; *)
<DISP GEN; The current generation must be complete and valid
<DISP FILE;
<SAVE MET;
8-38 P30305-X1118-G499-01-7618
If one of the following messages has been output on OMT:
! Message:
THE ACTUAL GENERATION ON XXXXX IS NOT COMPLETE AND NOT VALID.
0ACTIVATING WITHOUT LABELING NOT POSSIBLE
PLEASE ENTER:
<STOP MDDACT; or
<CONT MDDACT: LABEL=Y;
or
Message:
VOL-LABEL OF MDD-X IS UNVALID
ACTIVATING WITHOUT LABELING NOT POSSIBLE
PLEASE ENTER:
<STOP MDACT; or
<CONT MDDACT: LABEL=Y;
P30305-X1118-G499-01-7618 8-39
This page was left intentionally blank!
8-40 P30305-X1118-G499-01-7618
9. STARTUP ISTART2F WITH APS V17/CCNC
Initial position:
This recovery ISTART2F with APS V17/CCNC can be performed instead of Fallback to V11 if
the OSU startup and change over to APS V17/CCNC is not successful.
Before starting the ISTART2F from disk MDD-1, the APS V17/CCNC has to be prepared in
the Installation Recovery. E.g. MB and SN are configured to PLA, so the LTGs can be loaded
via 2 MCHs (MB-1 and SN-1 are in MBL before).
Press BOOT key on BCMY-1 and wait for display A925 on the MP
FORMAT;
INS;
IOC-1;
17xxxxxx;
P30305-X1118-G499-01-7618 9-1
Note:
After the system message ”INSTALL RECOVERY INFORMATION........” the APS can be
started as follows:
<password> <password>
<START FCP;
<START OM; Input command ca. 15 sec after ”START FCP” execution
<START SFGSW;
<START CSWD;
<RSET SPLITOPT;
9-2 P30305-X1118-G499-01-7618
9.1.4. Configuration of the Periphery
MB and SN are configured to PLA using command file ”CF.17.MBSNPLA1”.
<EXEC CMDFILE:FILE=CF.17.MBSNPLAG499;
<DEL FILE:FILE=SU.;
<END INSTALL;
YES:
P30305-X1118-G499-01-7618 9-3
This page was left intentionally blank!
9-4 P30305-X1118-G499-01-7618
10. PROJECT RELATED ITEMS
P30305-X1118-G499-01-7618 10-1
This page was left intentionally blank !
10-2 P30305-X1118-G499-01-7618
11. ABBREVIATIONS
ACT Active
AMA Automatic Message Account
APS Application Program System
BAP Base Processor
BCMY Access Bus for Common Memory
BCT Basic Craft Terminal
BIOC Bus for Input/Output Control
CAP Call Processor
CBL Conditional Blocked
CCG Central Clock Generator
CCNC Common Channel Signaling Network Control
CCNP Common Channel Signaling Network Processor
CCS7 Common Channel Signaling System No 7
CMY Common Memory
CP Coordination Processor
CP113C Coordination Processor 113 Type C
CSC Central Service Channel
DCC Direct Current Converter
DCP Data Communication Processor
DE4 Digital Equipment Type 4, SN(A/B): 63 LTG
DE51 Digital Equipment Type 51, SN(A/B): 126 LTG
DE52 Digital Equipment Type 52, SN(A/B): 252 LTG
DE54 Digital Equipment Type 54, SN(A/B): 504 LTG
DE60 Digital Equipment Type 60, SN(D): up to 252 LTG
DE61 Digital Equipment Type 61, SN(D): 252 LTG
DE62 Digital Equipment Type 62, SN(D): 504 LTG
DE64 Digital Equipment Type 64, SN(D): 1008 LTG
DIU Digital Interface Unit
DLU Digital Line Unit
DLUC Digital Line Unit Control
EBC Extended Binary Coded Decimal Interchange Code (EBCDIC)
EMCSP Emergency Call Station Party
EXCHID Exchange Identification Code
F:.... Frame: ....
F:PIOP Module Frame for Processor and Input/Output Processor
FP Fuse Panel
FSU Fast System Upgrade
FW Firmware
HW Hardware
IOC Input/Output Control
IOP Input/Output Processor
IOP:MB IOP for Message Buffer
IOP:UNI IOP Unified for O&M Devices
LM Feature
LMY Local Memory
LTG Line Trunk Group
M:.... Module:....
MAL Malicious Call Account
MAS Master
MB Message Buffer
MB(B) Message Buffer Type B
MB(D) Message Buffer Type D
MBL Maintenance Blocked
P30305-X1118-G499-01-7618 11-1
MBUL Message Buffer Unit LTG
MBUS Message Buffer Unit SGC
MCH Message Channel
MDD Magnetic Disk Device
MML Man Machine Language
MMN Maintenance Manual
MO Magneto-optical Disk
MOB Meter Observation Account
MOD Magneto-optical Disk Device
MOLOC Module Location
MUT Mounting Unit
NAC Not Accessible
NSS Non Switching System
OAM/OA&M Operation, Administration and Maintenance
OMC Operation & Maintenance Center
OMT Operation and Maintenance Terminal
OSU Optimized Software Upgrade
PEX Program Execution Part
PLA Planned
R:.... Rack:....
REFORM Reformation Tool for Database
REGEN Regeneration
SGC Switch Group Control
SN Switching Network
SN(A) Switching Network Type A
SN(B) Switching Network Type B
SPL Split
SPR Spare
SS Switching System
STB Standby
SYP System Panel
TSG Time Stage Group
UCT Upgrade Control Table
UNA Unavailable
UPT Upgrade Protocol Table
V... Version of APS
Vd Version Destination (new APS)
Vs Version Source (old APS)
VSN Magnetic Tape Number
VSNR Magnetic Tape Number Receiver
VSNS Magnetic Tape Number Sender
X25LINK X.25 Interface Link
11-2 P30305-X1118-G499-01-7618
12. REFERENCES
/1/ Procedure Description
P30305-X1118-E137-**-7618
Database Regeneration V11
CP113C
P30305-X1118-G499-01-7618 12-1
This page was left intentionally blank!
12-2 P30305-X1118-G499-01-7618
13. APPENDIX
13.1. CP113C
R:DEV B0 R:CP113C
MUT
8ft 8ft
FP FP:CP (Fuses) 01
C I
IOP- Group 2 for
Vacant A O 02 F:PIOP(A)-2
DE54
P4 C2
C I
A O IOP-Group 0 03 F:PIOP(A)-0
P2 C0
MTD-1 FAN 04
B C
A A 05 F:PBC-0
BCMY-0 CMY0
P0 P0
B C 06 F:PBC-1
A A
BCMY-1 CMY1
P1 P1
C I
MTD-0 A O IOP-Group 1 07 F:PIOP(A)-1
P3 C1
FAN 08
C I
A O IOP-Group 3 for DE54 09 F:PIOP(A)-3
P5 C3
FAN BOX 11
P30305-X1118-G499-01-7618 13-1
13.1.1.2. Rack Layout with F:PIOP(B)
FP FP:CP (Fuses) 01
Vacant CAP-4 CAP-8 IOC-2 IOP- Group 2 for 504 LTG 02 F:PIOP(B)-2
AMP-0/
CAP-2
CAP-6 IOC-0 IOP-Group 0 03 F:PIOP(B)-0
MTD-1 FAN 04
B C
A A BCMY-0 CMY0 05 F:PBC-0
P 0 P 0
B C 06 F:PBC-1
A A
BCMY-1 CMY1
P 1 P 1
AMP-1/
MTD-0 CAP-3
CAP-7 IOC-1 IOP- Group 1 07 F:PIOP(B)-1
FAN 08
2 x MDD
Vacant 10 F:DEV
1-2 x MOD
FAN 11
13-2 P30305-X1118-G499-01-7618
13.1.2. Frame Layout for Capacity Stage DE52
101 119 127 145 153 165 177 189 199 211 221 233 243 255 269 279 291 301 311 321 337
101 117 125 143 151 167 201 217 233 249 257 287 295 307 319 331 339
BAP-0 CAP-0 CAP-2
BAP-1 CAP-1 CAP-3
IOC-0 CAP-4
IOC-1 CAP-5
101 119 127 145 153 165 177 189 199 211 221 233 243 255 269 279 291 301 311 321 337
P30305-X1118-G499-01-7618 13-3
13.1.2.2. Frame Layout with F:PIOP(B)
Frame Equipping: F:PIOP(B)-0 in MUT-03
AMP-0/ IOP: IOP:
CAP-2 CAP-6 IOC-0 IOP:LAU IOP:LAU IOP:LAU IOP:LAU IOP:LAU UNI-0 IOP:MB´s TA-0
F:PIOP(B)-0
DCC PEX DCC PEX DCC PEX L L L L L L L L L L IOP IOP IOP IOP IOP IOP IOP DCC
MD MD MD A C A C A C A C A C UNI MB MB MB MB MB TA MD
U U U U U U U U U U 0 34 32 42 40 03
B B B B B B B B B B
101 119 131 149 161 179 191 199 207 215 277 235 243 251 263 271 281 289 297 305 313 321 329 341
101 117 125 143 151 167 201 217 233 249 257 287 295 307 319 331 339
BAP-0 CAP-0 CAP-2/ CAP-6
BAP-1 CAP-1 AMP-0 CAP-7
IOC-0 CAP-3/CAP-8
IOC-1 AMP-1 CAP-9
CAP-4
CAP-5
101 119 131 149 161 179 191 199 207 215 277 235 243 251 263 271 281 289 297 305 313 321 329 341
13-4 P30305-X1118-G499-01-7618
13.1.3. Frame Layout for Capacity Stage DE54
101 119 127 145 153 165 177 189 199 211 221 233 243 255 269 279 291 301 311 321 337
101 119 127 145 153 165 177 189 199 211 221 233 243 255 269 279 291 301 311 321 337
101 117 125 143 151 167 201 217 233 249 257 287 295 307 319 331 339
BAP-0 CAP-0 CAP-2
BAP-1 CAP-1 CAP-3
IOC-0 IOC-2 CAP-4
IOC-1 IOC-3 CAP-5
P30305-X1118-G499-01-7618 13-5
Frame Equipping: F:PBC-1 in MUT 06
101 119 127 145 153 165 177 189 199 211 221 233 243 255 269 279 291 301 311 321 337
101 119 127 145 153 165 177 189 199 211 221 233 243 255 269 279 291 301 311 321 337
13-6 P30305-X1118-G499-01-7618
13.1.3.3. Frame Layout with F:PIOP(B)
Frame Equipping: F:PIOP(B)-2 in MUT 02
101 119 131 149 161 179 289 297 305 313 321 329 341
101 119 131 149 161 179 281 289 297 305 313 321 329 341
101 117 125 143 151 167 201 217 233 249 257 287 295 307 319 331 339
BAP-0 CAP-0 CAP-2/ CAP-6
BAP-1 CAP-1 AMP-0 CAP-7
IOC-0 IOC-2 CAP-3/ CAP-8
IOC-1 IOC-3 AMP-1 CAP-9
CAP-4
CAP-5
P30305-X1118-G499-01-7618 13-7
Frame Equipping: F:PBC-1 in MUT 06
101 119 131 149 161 179 281 289 297 305 313 321 329 341
101 119 131 149 161 179 281 289 297 305 313 321 329 341
13-8 P30305-X1118-G499-01-7618
13.1.4. Fuse Assignment to the Functional CP Units
FU 01 03 05 07 09 11 13 15 17 19 21 23 25 27 29 31 33
- - - - - - - - - - - - - - - - -
02 04 06 08 10 12 14 16 18 20 22 24 26 28 30 32
Fuse assignment
P30305-X1118-G499-01-7618 13-9
13.1.4.2. R:CP113C with F:PIOP(B)
R:CP113C with F:PIOP(B), Fuse Panel FP:CP in MUT 01
FU 01 03 05 07 09 11 13 15 17 19 21 23 25 27 29 31 33
- - - - - - - - - - - - - - - - -
02 04 06 08 10 12 14 16 18 20 22 24 26 28 30 32
Fuse Assignment
13-10 P30305-X1118-G499-01-7618
13.1.5. Allocation of Log./Phys. IOPMBs to the Periphery
P30305-X1118-G499-01-7618 13-11
13.2. Message Buffer MB(B)
← DE4 →
D I C R T T C D F:SYPC(A)
DE52 C O O M R X D C
C C M E M A E C DE54
DE54 C A C
R L MUT 05
←DE52 w.3TSG→
← DE52 w. 4TSG →
13-12 P30305-X1118-G499-01-7618
13.2.2. Frame Equipping MB(B)
- Frame F:MB/CCG(B) S30804-B2641-X (basic with CCG-A)
MBU
1.MBU:LTG SGC 2.MBU:LTG CCG(A)
(0-0, 1-0) (0-0) (0-1,1-1) (0, 1)
(1-0)
LED
S1
MBU
1.MBU:LTG SGC 2.MBU:LTG
(0-2, 1-2) (0-1,1-1) (0-3,1-3)
(0-2,1-2)
(0-4, 1-4) (0-3,1-3) (0-5, 1-5)
(0-6, 1-6) (0-7, 1-7)
LED
S1
1 19 25 31 37 43 49 55 62 68 86
P30305-X1118-G499-01-7618 13-13
13.3. Message Buffer MB(D) (up to DE52)
ABOVE BELOW
F:TSG(B) 0-X
or MUT02 MUT02
F:SSG(B) 0-X F:LTGN
F:TSG(B) 1-X
or MUT03
F:SSG(B) 1-X FAN MUT03
M M M MUT04 M M M MUT04
B B B B B B
D D D F:MBD 0 D D D F:MBD 0
H C C H C C
0 G 0 G
M M M MUT05 M M M MUT05
B B B B B B
D D D F:MBD 1 D D D F:MBD 1
H C C H C C
0 G 0 G
13-14 P30305-X1118-G499-01-7618
13.3.2. R:LTGN (8ft) with F:MBD
ABOVE BELOW
MUT01
Fuse Panel MUT01 Fuse Panel
F:TSG(B) 1-X
or MUT03
F:SSG(B) 1-X F:LTGN
M M M MUT04 M M M MUT04
B B B B B B
D D D F:MBD 0 D D D F:MBD 0
H C C H C C
0 G 0 G
M M M MUT05 M M M MUT05
B B B B B B
D D D F:MBD 1 D D D F:MBD 1
H C C H C C
0 G 0 G
P30305-X1118-G499-01-7618 13-15
13.3.3. Fuse Assignment for R:LTG(N) (with MB(D))
- R:LTGN with F:MB(D), Fuse Panel
FUSE PANEL
ON
OFF
01 02 03 04 05 06 07 08 25 26 27 28 29 30 31 32
- Fuse Assignment
13-16 P30305-X1118-G499-01-7618
13.3.5. MB(D) Frames
- MB(D)-Frame F:MB(D) in MUT 04 (MB-0) and MUT 05 (MB-1) in R:MB(D) or R:LTGN:
C1 M M M M M M M M M M M M M M M
Modul: 2 B B B B B B B B B B B B B B B
3 D D D D D D D D D D D D D D D
4xMBDA 4 H A H A H C H C H A H A H A H
1xMBDC 5 G
1xMBDCG D1 0 2 7 0 6 1 4 1 3 4 2 3 5
8xMBDH 2
3
4
101 117 133 149 165 181 207 223 235 251 267 285 301 317 333
P30305-X1118-G499-01-7618 13-17
13.4. Command Files V11
13-18 P30305-X1118-G499-01-7618
13.4.2. Command File CF.11.ACTX25G499
<CMDFILE;
/* CF.11.ACTX25G499 */
/*
/***************************************************/
/* CF-NAME : CF.11.ACTX25G499 */
/* */
/* PURPOSE : ACTIVATION OF X25-LINKS */
/* */
/* COPYRIGHT (C) SIEMENS AG 2005 */
/* */
/* SSP-TYPE : CP113 */
/* */
/* AUTHOR : Com CD NC CC UP */
/* */
/* REMARKS : X25-LINK 0...7 */
/***************************************************/
/*
//***************************************************
//* COMMAND FILE CF.11.ACTX25G499 STARTED *
//***************************************************
//* ACTIVATION OF X25-LINK 0...7 *
//***************************************************
//* IGNORE ERROR MESSAGES IF X25LINK *
//* IS NOT AVAILABLE *
//***************************************************
/*
<SET CFOPT: ACKCFS=ALL,DANCMD=EXEC,ACKREQ=POS;
/*
<ENTR ALMODE: HLIM=YES;
/*
<STAT SSP;
/*
<CONF X25LINK:X25LINK=0,OST=MBL;
<CONF X25LINK:X25LINK=0,OST=ACT;
<CONF X25LINK:X25LINK=1,OST=MBL;
<CONF X25LINK:X25LINK=1,OST=ACT;
<CONF X25LINK:X25LINK=2,OST=MBL;
<CONF X25LINK:X25LINK=2,OST=ACT;
<CONF X25LINK:X25LINK=3,OST=MBL;
<CONF X25LINK:X25LINK=3,OST=ACT;
<CONF X25LINK:X25LINK=4,OST=MBL;
<CONF X25LINK:X25LINK=4,OST=ACT;
<CONF X25LINK:X25LINK=5,OST=MBL;
<CONF X25LINK:X25LINK=5,OST=ACT;
<CONF X25LINK:X25LINK=6,OST=MBL;
<CONF X25LINK:X25LINK=6,OST=ACT;
<CONF X25LINK:X25LINK=7,OST=MBL;
<CONF X25LINK:X25LINK=7,OST=ACT;
/*
<STAT SSP;
//***************************************************
//* AVAILABLE X25-LINKS MUST BE IN ACT *
//* IF NOT ACTIVATE X25-LINKS *
//***************************************************
/*
<RESET CFOPT;
<ENDFILE;
P30305-X1118-G499-01-7618 13-19
13.4.3. Command File CF.11.CANPATG499
<CMDFILE;
/* CF.11.CANPATG499 */
/*
/***************************************************/
/* CF-NAME : CF.11.CANPATG499 */
/* */
/* PURPOSE : CANCELLING AUXILIARY UPGRADE */
/* PATCHES V11 */
/* */
/* COPYRIGHT (C) SIEMENS AG 2005 */
/* */
/* SSP-TYPE : CP113 */
/* */
/* AUTHOR : Com CD NC CC UP */
/* */
/* REMARKS : */
/***************************************************/
/*
//***************************************************
//* COMMAND FILE CF.11.CANPATG499 STARTED *
//***************************************************
//* CANCELLING AUXILIARY UPGRADE PATCHES V11 *
//***************************************************
/*
<SET CFOPT: ACKCFS=ERROR,DANCMD=EXEC,ACKREQ=POS;
/*
<EXEC CMDFILE:FILE=PA.11.B2925L2J;
<EXEC CMDFILE:FILE=PA.11.SPLITCPJ;
<EXEC CMDFILE:FILE=PA.11.V1301L2J;
<EXEC CMDFILE:FILE=PA.11.V1302L2J;
/*
<RESET CFOPT;
<ENDFILE;
13-20 P30305-X1118-G499-01-7618
13.4.4. Command File CF.11.CPTESTG499
<CMDFILE;
/* CF.11.CPTESTG499 */
/*
/***************************************************/
/* CF-NAME : CF.11.CPTESTG499 */
/* */
/* LONG-NAME : TEST OF CP */
/* */
/* COPYRIGHT (C) SIEMENS AG 2005 */
/* */
/* SSP-TYPE : CP113 */
/* */
/* AUTHOR : Com CD NC CC UP */
/* */
/* PURPOSE : TEST OF CP, STAGE UP TO DE54 */
/* */
/* REMARKS : */
/***************************************************/
/*
//**************************************************/
//* COMMAND FILE CF.11.CPTESTG499 STARTED */
//**************************************************/
//**************************************************/
//* TEST OF CP113 */
//**************************************************/
/*
<SET CFOPT: ACKCFS=ALL, DANCMD=EXEC, ACKREQ=POS, OFF=16;
/*
<TEST BAP;
<SKIP CMD:LABEL=ERR,ON=32;
<COM BAP;
<SKIP CMD:LABEL=ERR,ON=32;
<TEST BAP;
<SKIP CMD:LABEL=ERR,ON=32;
<TEST IOC;
<SKIP CMD:LABEL=ERR,ON=32;
<TEST CMY;
<SKIP CMD:LABEL=ERR,ON=32;
<TEST BCMY;
<SKIP CMD:LABEL=ERR,ON=32;
<TEST IOPG:IOC=0;
<SKIP CMD:LABEL=ERR,ON=32;
<TEST IOPG:IOC=1;
<SKIP CMD:LABEL=ERR,ON=32;
<TEST CAP;
/*
//**************************************************/
//* IOC-2,3 ONLY IN CP-STAGE DE54 */
//**************************************************/
//* IGNORE ERROR MESSAGE IF STAGE IS < DE54 */
//**************************************************/
/*
<TEST IOPG:IOC=2;
<TEST IOPG:IOC=3;
/*
<RESET CFOPT;
//**************************************************/
//* CHECK IF ALL TESTS WERE SUCCESSFUL */
//**************************************************/
<ENDFILE;
/*
.ERR<STEP;
<SET CFOPT:ON=16, SCOPE=GLOBAL;
P30305-X1118-G499-01-7618 13-21
//**************************************************/
//* C O M M A N D N O T E X E C U T E D */
//**************************************************/
//* ELIMINATE FAULT AND ENTER NOT EXECUTED COMMANDS*/
//**************************************************/
<ENDFILE;
13-22 P30305-X1118-G499-01-7618
13.4.5. Command File CF.11.CRSUUCTG499
<CMDFILE;
/* CF.11.CRSUUCTG499 */
/*
/***************************************************/
/* CF-NAME : CF.11.CRSUUCTG499 */
/* */
/* PURPOSE : CREATION OF FILE SU.UCT FOR */
/* FUNCTION ISTART2F V11 */
/* */
/* COPYRIGHT (C) SIEMENS AG 2005 */
/* */
/* SSP-TYPE : CP113 */
/* */
/* AUTHOR : Com CD NC CC UP */
/* */
/* REMARKS : */
/***************************************************/
/*
//***************************************************
//* COMMAND FILE CF.11.CRSUUCTG499 STARTED *
//***************************************************
//* CREATING FILE SU.UCT FOR FUNCTION ISTART2F V11*
//***************************************************
/*
<SET CFOPT: ACKCFS=ALL,DANCMD=EXEC,ACKREQ=POS;
/*
<DISP FILE: FILE=SU.;
<DEL FILE: FILE=SU.UCT.TEMP;
<DACT SYSUPG;
/*
<EXEC EDTS8;
*1
*I
*1
*XXXXXXXXXXXXXXXXX
*.
*W SU.UCT.TEMP
*END
/*
<TRANS FILE: FILE=SU.UCT/SU.UCT.TEMP, MODE=CRD;
/*
<DEL FILE: FILE=SU.UCT.TEMP;
/*
<DISP FILE: FILE=SU.;
<DISP FILETEXT: FILE=SU.UCT;
/*
<ENDFILE;
P30305-X1118-G499-01-7618 13-23
13.4.6. Command File CF.11.DIAGCCNG499
<CMDFILE;
/* CF.11.DIAGCCNG499 */
/*
/***************************************************/
/* CF-NAME : CF.11.DIAGCCNG499 */
/* */
/* PURPOSE : DIAGNOSIS OF CCNC */
/* */
/* COPYRIGHT (C) SIEMENS AG 2005 */
/* */
/* SSP-TYPE : CP113 */
/* */
/* AUTHOR : Com CD NC CC UP */
/* */
/* REMARKS : INITIAL STATUS: CCNP-0 IN STB */
/* CCNP-1 IN ACT */
/***************************************************/
/*
//***************************************************
//* COMMAND FILE CF.11.DIAGCCNG499 STARTE *
//***************************************************
//* DIAGNOSIS OF CCNC *
//***************************************************
/*
<SET CFOPT: ACKCFS=ALL, DANCMD=EXEC, ACKREQ=POS, OFF=16;
/*
//***************************************************
//* DIAGNOSIS OF CCNP-0 *
//***************************************************
/*
<STAT SSP;
<STAT CCNC:UNIT=CCNP-X;
/*
<CONF CCNC:UNIT=CCNP-0,OST=MBL;
<SKIP CMD: ON=32, LABEL=ERR;
<DIAG CCNC:UNIT=CCNP-0;
<SKIP CMD: ON=32, LABEL=ERR;
/*
<CONF IOP:IOP=IOPMB-0,OST=MBL;
<SKIP CMD: ON=32, LABEL=ERR;
/*
<DIAG CCNC:UNIT=CCNP-0;
<SKIP CMD: ON=32, LABEL=ERR;
/*
<CONF CCNC:UNIT=CCNP-0,OST=STB;
<SKIP CMD: ON=32, LABEL=ERR;
<CONF CCNC:UNIT=CCNP-0,OST=ACT;
<SKIP CMD: ON=32, LABEL=ERR;
/*
<CONF IOP:IOP=IOPMB-0,OST=ACT;
<SKIP CMD: ON=32, LABEL=ERR;
/*
//**************************************************
//* DIAGNOSIS OF CCNP-1 *
//**************************************************
/*
<STAT SSP;
<STAT CCNC:UNIT=CCNP-X;
/*
<CONF CCNC:UNIT=CCNP-1,OST=MBL;
<SKIP CMD: ON=32, LABEL=ERR;
<DIAG CCNC:UNIT=CCNP-1;
<SKIP CMD: ON=32, LABEL=ERR;
13-24 P30305-X1118-G499-01-7618
/*
<CONF IOP:IOP=IOPMB-1,OST=MBL;
<SKIP CMD: ON=32, LABEL=ERR;
/*
<DIAG CCNC:UNIT=CCNP-1;
<SKIP CMD: ON=32, LABEL=ERR;
/*
<CONF CCNC:UNIT=CCNP-1,OST=STB;
<SKIP CMD: ON=32, LABEL=ERR;
/*
<CONF IOP:IOP=IOPMB-1,OST=ACT;
<SKIP CMD: ON=32, LABEL=ERR;
/*
<STAT SSP;
<STAT CCNC:UNIT=CCNP-X;
/*
<RESET CFOPT;
//**************************************************************
//* PLEASE CHECK FOR FAILURES AND IF CCNPS ARE IN ACT/STB, *
//* IOPMB-0,1 IN ACT *
//**************************************************************
<ENDFILE;
/*
/*
.ERR<STEP;
<SET CFOPT: ON=16, SCOPE=GLOBAL;
//**************************************************************
//* C O M M A N D N O T E X E C U T E D *
//**************************************************************
//* ELIMINATE FAULT AND ENTER NOT EXECUTED COMMANDS *
//**************************************************************
<ENDFILE;
P30305-X1118-G499-01-7618 13-25
13.4.7. Command File CF.11.DIAGMB0G499
<CMDFILE;
/* CF.11.DIAGMB0G499 */
/*
/***************************************************/
/* CF-NAME : CF.11.DIAGMB0G499 */
/* */
/* PURPOSE : DIAGNOSIS OF MB-0 */
/* */
/* COPYRIGHT (C) SIEMENS AG 2005 */
/* */
/* SSP-TYPE : CP113 */
/* */
/* AUTHOR : Com CD NC CC UP */
/* */
/* REMARKS : FOR MB CAPACITY STAGE UP TO DE54 */
/***************************************************/
/*
//***************************************************
//* COMMAND FILE CF.11.DIAGMB0G499 STARTED *
//***************************************************
/*
<SET CFOPT: ACKCFS=ALL, DANCMD=EXEC, ACKREQ=POS, OFF=16;
/*
//***************************************************
//* DIAGNOSIS OF MB-0 *
//***************************************************
/*
<DISP EXDDAT;
<STAT SSP;
<STAT MB;
<STAT SN;
/*
<CONF MB: MB=0,OST=MBL;
<SKIP CMD: ON=32, LABEL=ERR;
<DIAG MB: MB=0,TA=ALL;
<SKIP CMD: ON=32, LABEL=ERR;
/*
<CONF IOP:IOP=IOPMB-32,OST=MBL;
<SKIP CMD: ON=32, LABEL=ERR;
/*
//***************************************************
//* IOPMB-34 ONLY IN STAGE DE52,DE54 *
//***************************************************
/*
<CONF IOP:IOP=IOPMB-34,OST=MBL;
/*
//***************************************************
//* IOPMB-36,38 ONLY IN STAGE DE54 *
//***************************************************
/*
<CONF IOP:IOP=IOPMB-36,OST=MBL;
<CONF IOP:IOP=IOPMB-38,OST=MBL;
/*
<DIAG MB: MB=0,TA=ALL;
<SKIP CMD: ON=32, LABEL=ERR;
/*
<CONF MB: MB=0,OST=ACT;
<SKIP CMD: ON=32, LABEL=ERR;
/*
<CONF IOP:IOP=IOPMB-32,OST=ACT;
<SKIP CMD: ON=32, LABEL=ERR;
/*
<CONF IOP:IOP=IOPMB-34,OST=ACT;
13-26 P30305-X1118-G499-01-7618
<CONF IOP:IOP=IOPMB-36,OST=ACT;
<CONF IOP:IOP=IOPMB-38,OST=ACT;
/*
<STAT SSP;
<STAT MB;
<STAT SN;
/*
<RESET CFOPT;
//******************************************************
//* PLEASE CHECK FOR FAULTS AND IF MB-0,1, SN-0,1 *
//* AND IOPMBS ARE IN ACT *
//******************************************************
<ENDFILE;
/*
.ERR<STEP;
<SET CFOPT: ON=16, SCOPE=GLOBAL;
//*******************************************************
//* C O M M A N D N O T E X E C U T E D *
//*******************************************************
//* ELIMINATE FAULT AND ENTER NOT EXECUTED COMMANDS *
//*******************************************************
<ENDFILE;
P30305-X1118-G499-01-7618 13-27
13.4.8. Command File CF.11.DIAGMB1G499
<CMDFILE;
/* CF.11.DIAGMB1G499 */
/*
/***************************************************/
/* CF-NAME : CF.11.DIAGMB1G499 */
/* */
/* PURPOSE : DIAGNOSIS OF MB-1 */
/* */
/* COPYRIGHT (C) SIEMENS AG 2005 */
/* */
/* SSP-TYPE : CP113 */
/* */
/* AUTHOR : Com CD NC CC UP */
/* */
/* REMARKS : FOR MB CAPACITY STAGE UP TO DE54 */
/***************************************************/
/*
//***************************************************
//* COMMAND FILE CF.11.DIAGMB1G499 STARTED *
//***************************************************
/*
<SET CFOPT: ACKCFS=ALL, DANCMD=EXEC, ACKREQ=POS, OFF=16;
/*
//***************************************************
//* DIAGNOSIS OF MB-1 *
//***************************************************
/*
<DISP EXDDAT;
<STAT SSP;
<STAT MB;
<STAT SN;
/*
<CONF MB: MB=1,OST=MBL;
<SKIP CMD: ON=32, LABEL=ERR;
<DIAG MB: MB=1,TA=ALL;
<SKIP CMD: ON=32, LABEL=ERR;
/*
<CONF IOP:IOP=IOPMB-33,OST=MBL;
<SKIP CMD: ON=32, LABEL=ERR;
/*
//***************************************************
//* IOPMB-35 ONLY IN STAGE DE52,DE54 *
//***************************************************
/*
<CONF IOP:IOP=IOPMB-35,OST=MBL;
/*
//***************************************************
//* IOPMB-37,39 ONLY IN STAGE DE54 *
//***************************************************
/*
<CONF IOP:IOP=IOPMB-37,OST=MBL;
<CONF IOP:IOP=IOPMB-39,OST=MBL;
/*
<DIAG MB: MB=1,TA=ALL;
<SKIP CMD: ON=32, LABEL=ERR;
/*
<CONF MB: MB=1,OST=ACT;
<SKIP CMD: ON=32, LABEL=ERR;
/*
<CONF IOP:IOP=IOPMB-33,OST=ACT;
<SKIP CMD: ON=32, LABEL=ERR;
/*
<CONF IOP:IOP=IOPMB-35,OST=ACT;
13-28 P30305-X1118-G499-01-7618
<CONF IOP:IOP=IOPMB-37,OST=ACT;
<CONF IOP:IOP=IOPMB-39,OST=ACT;
/*
<STAT SSP;
<STAT MB;
<STAT SN;
/*
<RESET CFOPT;
//******************************************************
//* PLEASE CHECK FOR FAULTS AND IF MB-0,1, SN-0,1 *
//* AND IOPMBS ARE IN ACT *
//******************************************************
<ENDFILE;
/*
.ERR<STEP;
<SET CFOPT: ON=16, SCOPE=GLOBAL;
//*******************************************************
//* C O M M A N D N O T E X E C U T E D *
//*******************************************************
//* ELIMINATE FAULT AND ENTER NOT EXECUTED COMMANDS *
//*******************************************************
<ENDFILE;
P30305-X1118-G499-01-7618 13-29
13.4.9. Command File CF.11.DIUSTATG499
<CMDFILE;
/* CF.11.DIUSTATG499*/
/*
/***************************************************/
/* CF-NAME : CF.11.DIUSTATG499 */
/* */
/* PURPOSE : INQUIRY DIU AND CR STATUS */
/* */
/* COPYRIGHT (C) SIEMENS AG 2005 */
/* */
/* SSP-TYPE : CP113 */
/* */
/* AUTHOR : Com CD NC CC UP */
/* */
/* REMARKS : */
/***************************************************/
/*
//***************************************************
//* COMMAND FILE CF.11.DIUSTATG499 STARTE *
//***************************************************
//* INQUIRY OF DIU AND CR STATUS *
//***************************************************
/*
<SET CFOPT: ACKCFS=ALL,DANCMD=EXEC,ACKREQ=POS, OFF=16;
/*
//********************************************/
//* INQUIRY OF DIU IN ACT */
//********************************************/
<STAT DIU: LTG=X-X, OST=ACT;
/*
/*
//********************************************/
//* INQUIRY OF DIU IN CBL */
//********************************************/
<STAT DIU: LTG=X-X, OST=CBL;
/*
/*
//********************************************/
//* INQUIRY OF DIU IN MBL */
//********************************************/
<STAT DIU: LTG=X-X, OST=MBL;
/*
/*
//********************************************/
//* INQUIRY OF DIU IN PLA */
//********************************************/
<STAT DIU: LTG=X-X, OST=PLA;
/*
/*
//********************************************/
//* INQUIRY OF CR IN ACT */
//********************************************/
<STAT CR: LTG=X-X, OST=ACT;
/*
/*
//********************************************/
//* INQUIRY OF CR IN MBL */
//********************************************/
<STAT CR: LTG=X-X, OST=MBL;
/*
/*
//********************************************/
//* INQUIRY OF CR IN PLA */
13-30 P30305-X1118-G499-01-7618
//********************************************/
<STAT CR: LTG=X-X, OST=PLA;
/*
<RESET CFOPT;
<ENDFILE;
P30305-X1118-G499-01-7618 13-31
13.4.10. Command File CF.11.MBSNPLAG499
<CMDFILE;
/* CF.11.MBSNPLAG499 */
/*
/***************************************************/
/* CF-NAME : CF.11.MBSNPLAG499 */
/* */
/* PURPOSE : CONFIGURATION OF MB AND SN */
/* TO PLA,SIDE 1 */
/* */
/* COPYRIGHT (C) SIEMENS AG 2005 */
/* */
/* SSP-TYPE : CP113 */
/* */
/* AUTHOR : Com CD NC CC UP */
/* */
/* REMARKS : CAPACITY STAGE IS UP TO SN:504LTG*/
/***************************************************/
/*
//***************************************************
//* COMMAND FILE CF.11.MBSNPLAG499 STARTED *
//***************************************************
//* CONFIGURATION OF MB AND SN TO PLA *
//* CAPACITY STAGE IS UP TO SN:504LTG *
//***************************************************
/*
<SET CFOPT: ACKCFS=ALL,DANCMD=EXEC,ACKREQ=POS;
/*
<DISP EXDDAT;
/*
//***************************************************
//* CONFIGURATION OF SN TO MBL *
//***************************************************
//***************************************************
//* IGNORE ERROR MESSAGE FOR UNITS NOT AVAILABLE *
//***************************************************
/*
<STAT SN;
/*
<CONF TSG: SN=1, TSG=0, OST=MBL;
<CONF TSG: SN=1, TSG=1, OST=MBL;
<CONF TSG: SN=1, TSG=2, OST=MBL;
<CONF TSG: SN=1, TSG=3, OST=MBL;
<CONF TSG: SN=1, TSG=4, OST=MBL;
<CONF TSG: SN=1, TSG=5, OST=MBL;
<CONF TSG: SN=1, TSG=6, OST=MBL;
<CONF TSG: SN=1, TSG=7, OST=MBL;
/*
<CONF SSG: SN=1, SSG=0, OST=MBL;
<CONF SSG: SN=1, SSG=1, OST=MBL;
<CONF SSG: SN=1, SSG=2, OST=MBL;
<CONF SSG: SN=1, SSG=3, OST=MBL;
/*
//***************************************************
//* CONFIGURATION OF MB TO MBL *
//***************************************************
//***************************************************
//* IGNORE ERROR MESSAGE FOR UNITS NOT AVAILABLE *
//***************************************************
/*
<STAT MB;
/*
<CONF MBUL: MB=1, MBUL=0, OST=MBL;
<CONF MBUL: MB=1, MBUL=1, OST=MBL;
13-32 P30305-X1118-G499-01-7618
<CONF MBUL: MB=1, MBUL=2, OST=MBL;
<CONF MBUL: MB=1, MBUL=3, OST=MBL;
<CONF MBUL: MB=1, MBUL=4, OST=MBL;
<CONF MBUL: MB=1, MBUL=5, OST=MBL;
<CONF MBUL: MB=1, MBUL=6, OST=MBL;
<CONF MBUL: MB=1, MBUL=7, OST=MBL;
/*
<CONF MBUS: MB=1, MBUS=0, OST=MBL;
<CONF MBUS: MB=1, MBUS=1, OST=MBL;
<CONF MBUS: MB=1, MBUS=2, OST=MBL;
<CONF MBUS: MB=1, MBUS=3, OST=MBL;
/*
//***************************************************
//* CONFIGURATION OF SN TO PLA *
//***************************************************
//***************************************************
//* IGNORE ERROR MESSAGE FOR UNITS NOT AVAILABLE *
//***************************************************
/*
<CONF TSG: SN=1, TSG=0, OST=PLA;
<CONF TSG: SN=1, TSG=1, OST=PLA;
<CONF TSG: SN=1, TSG=2, OST=PLA;
<CONF TSG: SN=1, TSG=3, OST=PLA;
<CONF TSG: SN=1, TSG=4, OST=PLA;
<CONF TSG: SN=1, TSG=5, OST=PLA;
<CONF TSG: SN=1, TSG=6, OST=PLA;
<CONF TSG: SN=1, TSG=7, OST=PLA;
/*
<CONF SSG: SN=1, SSG=0, OST=PLA;
<CONF SSG: SN=1, SSG=1, OST=PLA;
<CONF SSG: SN=1, SSG=2, OST=PLA;
<CONF SSG: SN=1, SSG=3, OST=PLA;
/*
//***************************************************
//* CONFIGURATION OF MB TO PLA *
//***************************************************
//***************************************************
//* IGNORE ERROR MESSAGE FOR UNITS NOT AVAILABLE *
//***************************************************
/*
<CONF MBUL: MB=1, MBUL=0, OST=PLA;
<CONF MBUL: MB=1, MBUL=1, OST=PLA;
<CONF MBUL: MB=1, MBUL=2, OST=PLA;
<CONF MBUL: MB=1, MBUL=3, OST=PLA;
<CONF MBUL: MB=1, MBUL=4, OST=PLA;
<CONF MBUL: MB=1, MBUL=5, OST=PLA;
<CONF MBUL: MB=1, MBUL=6, OST=PLA;
<CONF MBUL: MB=1, MBUL=7, OST=PLA;
/*
<CONF MBUS: MB=1, MBUS=0, OST=PLA;
<CONF MBUS: MB=1, MBUS=1, OST=PLA;
<CONF MBUS: MB=1, MBUS=2, OST=PLA;
<CONF MBUS: MB=1, MBUS=3, OST=PLA;
/*
<STAT MB;
/*
//***************************************************
//* CHECK MB STATUS *
//* ALL AVAILABLE MB-UNITS MUST HAVE STATUS PLA *
//***************************************************
/*
<STAT SN;
/*
//***************************************************
//* CHECK SN STATUS *
//* ALL AVAILABLE SN-UNITS MUST HAVE STATUS PLA *
P30305-X1118-G499-01-7618 13-33
//***************************************************
/*
<RESET CFOPT;
<ENDFILE;
13-34 P30305-X1118-G499-01-7618
13.4.11. Command File CF.11.PLACSCG499
<CMDFILE;
/* CF.11.PLACSCG499 */
/*
/***************************************************/
/* CF-NAME : CF.11.PLACSCG499 */
/* */
/* LONG-NAME : CONFIGURATION OF CSC-LINKS */
/* TO PLA */
/* */
/* COPYRIGHT (C) SIEMENS AG 2005 */
/* */
/* SSP-TYPE : CP113 */
/* */
/* AUTHOR : Com CD NC CC UP */
/* */
/* PURPOSE : CONFIGURATION OF CSC-LINKS */
/* TO PLA: */
/* CSC-0 UP TO CSC-3 */
/***************************************************/
/*
<SET CFOPT: ACKCFS=ALL,DANCMD=EXEC,ACKREQ=POS;
/*
//***************************************************
//* COMMANDFILE CF.11.PLACSCG499 STARTED *
//***************************************************
//***************************************************
//* CONFIGURATION OF CSC-LINKS TO PLA: *
//* CSC-0 UP TO 3 *
//***************************************************
//***************************************************
//* IGNORE ERROR MESSAGE FOR NOT AVAILABLE *
//* CSC-LINKS *
//***************************************************
/*
<STAT SSP;
/*
<CONF CSC:CSC=0,OST=MBL;
<CONF CSC:CSC=0,OST=PLA;
<CONF CSC:CSC=1,OST=MBL;
<CONF CSC:CSC=1,OST=PLA;
<CONF CSC:CSC=2,OST=MBL;
<CONF CSC:CSC=2,OST=PLA;
<CONF CSC:CSC=3,OST=MBL;
<CONF CSC:CSC=3,OST=PLA;
/*
<STAT SSP;
/*
//***************************************************
//* COMMANDFILE FINISHED *
//***************************************************
//***************************************************
//* CHECK STATUS OF CSC-LINKS: *
//* ALL AVAILABLE CSC-LINKS IN PLA *
//***************************************************
//***************************************************
//* IF NECESSARY CONFIGURE CSC-LINKS MANUALLY *
//***************************************************
/*
<RESET CFOPT;
<ENDFILE;
P30305-X1118-G499-01-7618 13-35
13.4.12. Command File CF.11.PLAX25G499
<CMDFILE;
/* CF.11.PLAX25G499 */
/*
/***************************************************/
/* CF-NAME : CF.11.PLAX25G499 */
/* */
/* PURPOSE : CONFIGURATION OF X25-LINKS */
/* TO PLA */
/* */
/* COPYRIGHT (C) SIEMENS AG 2005 */
/* */
/* SSP-TYPE : CP113 */
/* */
/* AUTHOR : Com CD NC CC UP */
/* */
/* REMARKS : X25-LINK 0...7 */
/***************************************************/
/*
//***************************************************
//* COMMAND FILE CF.11.PLAX25G499 STARTED *
//***************************************************
//* CONFIGURATION OF X25-LINK 0..7 TO PLA *
//***************************************************
//***************************************************
//* IGNORE ERROR MESSAGES IF X25-LINK *
//* IS NOT AVAILABLE *
//***************************************************
/*
<SET CFOPT: ACKCFS=ALL,DANCMD=EXEC,ACKREQ=POS;
/*
<CONF X25LINK:X25LINK=0,OST=MBL;
<CONF X25LINK:X25LINK=0,OST=PLA;
<CONF X25LINK:X25LINK=1,OST=MBL;
<CONF X25LINK:X25LINK=1,OST=PLA;
<CONF X25LINK:X25LINK=2,OST=MBL;
<CONF X25LINK:X25LINK=2,OST=PLA;
<CONF X25LINK:X25LINK=3,OST=MBL;
<CONF X25LINK:X25LINK=3,OST=PLA;
<CONF X25LINK:X25LINK=4,OST=MBL;
<CONF X25LINK:X25LINK=4,OST=PLA;
<CONF X25LINK:X25LINK=5,OST=MBL;
<CONF X25LINK:X25LINK=5,OST=PLA;
<CONF X25LINK:X25LINK=6,OST=MBL;
<CONF X25LINK:X25LINK=6,OST=PLA;
<CONF X25LINK:X25LINK=7,OST=MBL;
<CONF X25LINK:X25LINK=7,OST=PLA;
/*
<STAT SSP;
/*
//***************************************************
//* CHECK STATUS OF X25-LINKS *
//* X25-LINK 0...7 MUST BE IN PLA *
//***************************************************
/*
<RESET CFOPT;
<ENDFILE;
13-36 P30305-X1118-G499-01-7618
13.4.13. Command File CF.11.REGMEMTG499
<CMDFILE;
/* CF.11.REGMEMTG499 */
/*
/***************************************************/
/* CF-NAME : CF.11.REGMEMTG499 */
/* */
/* PURPOSE : CREATING AND SAVING THE CA */
/* FILES FOR REGENERATION */
/* ON MAGNETIC TAPE IN MTD-0 */
/* */
/* COPYRIGHT (C) SIEMENS AG 2005 */
/* */
/* SSP-TYPE : CP113 */
/* */
/* AUTHOR : Com CD NC CC UP */
/* */
/* REMARKS : A TAPE IS TO BE HELD READY. */
/* BEFORE STARTING THE COMMANDFILE */
/* THE MTD-0 IS TO BE LOADED */
/***************************************************/
/*
<SET CFOPT: ACKCFS=ERROR,DANCMD=EXEC,ACKREQ=POS,OFF=2;
/*
//***************************************************
//* COMMAND FILE CF.11.REGMEMTG499 STARTED *
//***************************************************
//* CREATING AND SAVING REGENERATION FILES *
//***************************************************
/*
//***************************************************
//* CHECKING IF CA.SU.APS.99 OR CA.TF.APS.99 *
//* IS ALREADY EXISTING *
//***************************************************
/*
<DISP FILE: FILE=CA.SU.APS.99;
<SKIPCMD: LABEL=MS, ON=32;
<SET CFOPT: ON=2;
/*
.MS <STEP;
<DISP FILE: FILE=CA.TF.APS.99;
<SKIPCMD: LABEL=CHECK, ON=32;
<SET CFOPT: ON=2;
/*
.CHECK <STEP;
<SKIPCMD: LABEL=ERROR, ON=2;
/*
/*
<DACT FNS: FNS=CA;
<INIT MT: MTD=0, CD=ISO, VSN=REGFIL;
<SKIPCMD: LABEL=ERR1, ON=32;
/*
<DISP FILE: FILE=CA.SU.UCHA;
<SKIPCMD: LABEL=AV2, OFF=32;
/*
//********************************************
//* FILE CA.SU.UCHA NOT EXISTING *
//* NO REGENERATION OF SUBSCRIBER-METERS *
//********************************************
<SKIPCMD: LABEL=S130;
/*
/*
.AV2 <STEP;
//********************************************
P30305-X1118-G499-01-7618 13-37
//* CREATION OF REGENERATIONFILE FOR *
//* SUBSCRIBER-METERS *
//********************************************
/*
<SAVE MET: TYPE=METSUB;
<SKIPCMD: LABEL=ERR3, ON=32;
<EDIT MET: FILE=CA.SU.APS.99, TYPE=METSUB, FUNC=APSCHANG;
<SKIPCMD: LABEL=ERR6, ON=32;
<TRANS FILE: FILE=CA.SU.APS.99, VSNR=REGFIL;
<SKIPCMD: LABEL=ERR5, ON=32;
/*
/*
.S130 <STEP;
<DISP FILE: FILE=CA.TF.UCHA;
<SKIPCMD: LABEL=AV3, OFF=32;
//********************************************
//* FILE CA.TF.UCHA NOT EXISTING *
//* NO REGENERATION OF S130-METERS *
//********************************************
<SKIPCMD: LABEL=OKAY;
/*
/*
.AV3 <STEP;
//********************************************
//* CREATION OF REGENERATIONFILE FOR *
//* S130-METERS *
//********************************************
/*
<SAVE MET: TYPE=METTFS;
<SKIPCMD: LABEL=ERR3, ON=32;
<EDIT MET: TYPE=METTFS, FILE=CA.TF.APS.99, FUNC=APSCHANG;
<SKIPCMD: LABEL=ERR8, ON=32;
<TRANS FILE: FILE=CA.TF.APS.99, VSNR=REGFIL;
<SKIPCMD: LABEL=ERR5, ON=32;
/*
<SKIPCMD: LABEL=OKAY;
/*
/*
.ERR1 <STEP;
// *************
// * FAULT 01 *
//********************************************
//* TAPE INITIALIZATION ERROR *
//********************************************
/*
<SKIPCMD: LABEL=END;
/*
/*
.ERR3 <STEP;
// *************
// * FAULT 03 *
//********************************************
//* METER SAVING FAULT *
//********************************************
/*
<SKIPCMD: LABEL=END;
/*
/*
.ERR5 <STEP;
// *************
// * FAULT 05 *
//********************************************
//* FAULT DURING FILETRANSFER *
//* ELIMINATE FAULT AND START PROCEDURE AGAIN*
//********************************************
/*
13-38 P30305-X1118-G499-01-7618
<SET CFOPT: ACKCFS=ALL;
<DISP MT: MTD=0;
<DISP FILE: VSN=REGFIL;
<SKIP CMD: LABEL=END;
/*
/*
.ERR6 <STEP;
// *************
// * FAULT 06 *
//********************************************
//* FAULT DURING CREATION OF SUBSCRIBERFILE *
//********************************************
<SKIPCMD: LABEL=END;
/*
/*
.ERR8 <STEP;
// *************
// * FAULT 08 *
//********************************************
//* FAULT DURING CREATION OF S130-FILE *
//********************************************
/*
<SKIPCMD: LABEL=END;
/*
/*
.OKAY <SET CFOPT: ACKCFS=ALL;
<DISP FILE: VSN=REGFIL;
//
//********************************************
//* ALL EXISTING CHARGE-FILES ON TAPE *
//* AVAILABLE ? *
//********************************************
/*
/*
<ACT FNS;
.END <ACT FNS: FNS=CA;
<RESET CFOPT;
<ENDFILE;
/*
/*
.ERROR <STEP;
/*
<RESET CFOPT;
//********************************************
//* FILE CA.SU.APS.99 AND/OR CA.TF.APS.99 *
//* ALREADY EXISTING *
//* CANCEL THE EXISTING FILES AND START *
//* COMMAND FILE CF.11.REGMEMT0 AGAIN *
//********************************************
//* ERROR *
//********************************************
<ENDFILE;
P30305-X1118-G499-01-7618 13-39
13.4.14. Command File CF.11.REGMEMOG499
<CMDFILE;
/* CF.11.REGMEMOG499 */
/*
/***************************************************/
/* CF-NAME : CF.11.REGMEMOG499 */
/* */
/* PURPOSE : CREATING AND SAVING THE CA */
/* FILES FOR REGENERATION */
/* ON MO IN MOD-0 */
/* */
/* COPYRIGHT (C) SIEMENS AG 2005 */
/* */
/* SSP-TYPE : CP113 */
/* */
/* AUTHOR : Com CD NC CC UP */
/* */
/* REMARKS : A MO IS TO BE HELD READY. */
/* BEFORE STARTING THE COMMANDFILE */
/* THE MOD-0 IS TO BE LOADED */
/***************************************************/
/*
<SET CFOPT: ACKCFS=ERROR,DANCMD=EXEC,ACKREQ=POS,OFF=2;
/*
//***************************************************
//* COMMAND FILE CF.11.REGMEMOG499 STARTED *
//***************************************************
//* CREATING AND SAVING REGENERATION FILES *
//***************************************************
/*
//***************************************************
//* CHECKING IF CA.SU.APS.99 OR CA.TF.APS.99 *
//* IS ALREADY EXISTING *
//***************************************************
/*
<DISP FILE: FILE=CA.SU.APS.99;
<SKIPCMD: LABEL=MS, ON=32;
<SET CFOPT: ON=2;
/*
.MS <STEP;
<DISP FILE: FILE=CA.TF.APS.99;
<SKIPCMD: LABEL=CHECK, ON=32;
<SET CFOPT: ON=2;
/*
.CHECK <STEP;
<SKIPCMD: LABEL=ERROR, ON=2;
/*
/*
<DACT FNS: FNS=CA;
<INIT MO: MOD=0, CD=ISO, VSN=REGFIL;
<SKIPCMD: LABEL=ERR1, ON=32;
/*
<DISP FILE: FILE=CA.SU.UCHA;
<SKIPCMD: LABEL=AV2, OFF=32;
/*
//********************************************
//* FILE CA.SU.UCHA NOT EXISTING *
//* NO REGENERATION OF SUBSCRIBER-METERS *
//********************************************
<SKIPCMD: LABEL=S130;
/*
/*
.AV2 <STEP;
//********************************************
13-40 P30305-X1118-G499-01-7618
//* CREATION OF REGENERATIONFILE FOR *
//* SUBSCRIBER-METERS *
//********************************************
/*
<SAVE MET: TYPE=METSUB;
<SKIPCMD: LABEL=ERR3, ON=32;
<EDIT MET: FILE=CA.SU.APS.99, TYPE=METSUB, FUNC=APSCHANG;
<SKIPCMD: LABEL=ERR6, ON=32;
<TRANS FILE: FILE=CA.SU.APS.99, VSNR=REGFIL;
<SKIPCMD: LABEL=ERR5, ON=32;
/*
/*
.S130 <STEP;
<DISP FILE: FILE=CA.TF.UCHA;
<SKIPCMD: LABEL=AV3, OFF=32;
//********************************************
//* FILE CA.TF.UCHA NOT EXISTING *
//* NO REGENERATION OF S130-METERS *
//********************************************
<SKIPCMD: LABEL=OKAY;
/*
/*
.AV3 <STEP;
//********************************************
//* CREATION OF REGENERATIONFILE FOR *
//* S130-METERS *
//********************************************
/*
<SAVE MET: TYPE=METTFS;
<SKIPCMD: LABEL=ERR3, ON=32;
<EDIT MET: TYPE=METTFS, FILE=CA.TF.APS.99, FUNC=APSCHANG;
<SKIPCMD: LABEL=ERR8, ON=32;
<TRANS FILE: FILE=CA.TF.APS.99, VSNR=REGFIL;
<SKIPCMD: LABEL=ERR5, ON=32;
/*
<SKIPCMD: LABEL=OKAY;
/*
/*
.ERR1 <STEP;
// *************
// * FAULT 01 *
//********************************************
//* MO INITIALIZATION ERROR *
//********************************************
/*
<SKIPCMD: LABEL=END;
/*
/*
.ERR3 <STEP;
// *************
// * FAULT 03 *
//********************************************
//* METER SAVING FAULT *
//********************************************
/*
<SKIPCMD: LABEL=END;
/*
/*
.ERR5 <STEP;
// *************
// * FAULT 05 *
//********************************************
//* FAULT DURING FILETRANSFER *
//* ELIMINATE FAULT AND START PROCEDURE AGAIN*
//********************************************
/*
P30305-X1118-G499-01-7618 13-41
<SET CFOPT: ACKCFS=ALL;
<DISP MO: MOD=0;
<DISP FILE: VSN=REGFIL;
<SKIP CMD: LABEL=END;
/*
/*
.ERR6 <STEP;
// *************
// * FAULT 06 *
//********************************************
//* FAULT DURING CREATION OF SUBSCRIBERFILE *
//********************************************
<SKIPCMD: LABEL=END;
/*
/*
.ERR8 <STEP;
// *************
// * FAULT 08 *
//********************************************
//* FAULT DURING CREATION OF S130-FILE *
//********************************************
/*
<SKIPCMD: LABEL=END;
/*
/*
.OKAY <SET CFOPT: ACKCFS=ALL;
<DISP FILE: VSN=REGFIL;
//
//********************************************
//* ALL EXISTING CHARGE-FILES ON MO *
//* AVAILABLE ? *
//********************************************
/*
/*
<ACT FNS;
.END <ACT FNS: FNS=CA;
<RESET CFOPT;
<ENDFILE;
/*
/*
.ERROR <STEP;
/*
<RESET CFOPT;
//********************************************
//* FILE CA.SU.APS.99 AND/OR CA.TF.APS.99 *
//* ALREADY EXISTING *
//* CANCEL THE EXISTING FILES AND START *
//* COMMAND FILE CF.11.REGMEMO0 AGAIN *
//********************************************
//* ERROR *
//********************************************
<ENDFILE;
13-42 P30305-X1118-G499-01-7618
13.4.15. Command File CF.11.PROG499
<CMDFILE;
/* CF.11.PROG499 */
/*
/***************************************************/
/* CF-NAME : CF.11.PROG499 */
/* */
/* PURPOSE : START OF PROCESSES IN */
/* INSTALLATION RECOVERY V11 */
/* */
/* COPYRIGHT (C) SIEMENS AG 2005 */
/* */
/* SSP-TYPE : CP113 */
/* */
/* AUTHOR : Com CD NC CC UP */
/* */
/* REMARKS : */
/***************************************************/
/*
//***************************************************
//* COMMAND FILE CF.11.PROG499 STARTED *
//***************************************************
//* STARTING PROCESSES IN INSTALLATION RECOVERY V11 *
//***************************************************
/*
<SET CFOPT: ACKCFS=ERROR,DANCMD=EXEC,ACKREQ=POS;
/*
<START OM: APPL=Q3IF;
/*
<START DB;
/*
<START PROCESS: NAME=ICSRV;
/*
<START PROCESS: NAME=CLTLM;
/*
<START PROCESS: NAME=QACEN;
/*
<START PROCESS: NAME=GAILS;
/*
<START PROCESS: NAME=JIAUP;
/*
<START PROCESS: NAME=ASCEX;
/*
<RESET CFOPT;
<ENDFILE;
P30305-X1118-G499-01-7618 13-43
13.4.16. Command File CF.11.SYSTATG499
<CMDFILE;
/* CF.11.SYSTATG499 */
/*
/***************************************************/
/* CF-NAME : CF.11.SYSTATG499 */
/* */
/* PURPOSE : INQUIRY OF SYSTEM STATUS */
/* */
/* COPYRIGHT (C) SIEMENS AG 2005 */
/* */
/* SSP-TYPE : CP113 */
/* */
/* AUTHOR : Com CD NC CC UP */
/* */
/* REMARKS : */
/***************************************************/
/*
//***************************************************
//* COMMAND FILE CF.11.SYSTATG499 STARTED *
//***************************************************
//* INQUIRY OF SYSTEM STATUS *
//***************************************************
/*
<SET CFOPT: ACKCFS=ALL,DANCMD=EXEC,ACKREQ=POS;
/*
//********************************************
//* INQUIRY OF UPDATE STATUS *
//********************************************
<DISP SPLITOPT;
<DISP UPDATE;
<STAT LOG;
/*
//********************************************
//* INQUIRY OF DISK CONTENTS *
//********************************************
<DISP FILE;
<DISP MD;
<DISP GEN;
/*
/*
//********************************************
//* INQUIRY OF SYSTEM REDUNDANCY *
//********************************************
<STAT SSP;
<STAT MB;
<STAT SN;
<DISP TSG: SN=X;
<STAT CCG;
<DISP CCG;
<STAT SYP;
<DISP LTG: LTG=X-X;
<STAT LTG: LTG=X-X;
<DISP DLU: DLU=X;
<STAT DLU: DLU=X;
<STAT DIU: LTG=X-X, OST=UNA;
<STAT CR: LTG=X-X, OST=UNA;
/*
/*
//********************************************
//* INQUIRY OF CCNC STATUS *
//********************************************
<STAT CCNC: UNIT=CCNP-X;
<STAT CCNC: UNIT=SIPA-X;
13-44 P30305-X1118-G499-01-7618
<STAT CCNC: UNIT=SILTC-X;
<STAT CCNC: UNIT=MUXM-X;
<STAT CCNC: UNIT=SILT-X;
/*
<DISP C7LINK: LSNAM=X;
<DISP C7LSET: LSNAM=X;
<DISP C7DP: DPC=X, NETIND=NAT0;
<DISP NUC;
/*
//********************************************
//* INQUIRY OF EXCHANGE DATA *
//********************************************
<DISP EXDDAT;
<STAT V5LINK: V5IFID=X, OST=ACT;
<DISP OUTSUP;
<DISP IAFEAT;
<DISP IAOPT;
<DISP METSAV;
<DISP SSPRT;
/*
//**********************************************
//* CHECK INTERROGATION RESULTS *
//**********************************************
//* IF NECESSARY CREATE REQUIRED CONFIGURATION *
//**********************************************
/*
<RESET CFOPT;
<ENDFILE;
P30305-X1118-G499-01-7618 13-45
13.4.17. Command File CF.11.UPDFILEG499
<CMDFILE;
/* CF.11.UPDFILEG499 */
/*
/***************************************************/
/* CF-NAME : CF.11.UPDFILEG499 */
/* */
/* PURPOSE : UPDATE OF CHARGE FILES ON DISK */
/* */
/* COPYRIGHT (C) SIEMENS AG 2005 */
/* */
/* SSP-TYPE : CP113 */
/* */
/* AUTHOR : Com CD NC CC UP */
/* */
/* REMARKS : */
/***************************************************/
/*
//***************************************************
//* COMMAND FILE CF.11.UPDFILEG499 STARTED *
//***************************************************
//* UPDATING CHARGE FILES ON DISK *
//***************************************************
/*
<SET CFOPT: ACKCFS=ALL,DANCMD=EXEC,ACKREQ=POS;
/*
//***************************************************
//* UPDATING CA METER FILES ON DISK *
//***************************************************
//* IGNORE ERROR MESSAGE IF METER TYPE IS *
//* NOT AVAILABLE *
//***************************************************
/*
<DISP EXDDAT;
/*
<SAVE MET:TYPE=METSUB;
<SAVE MET:TYPE=METSTAT;
<SAVE MET:TYPE=METTR;
<SAVE MET:TYPE=METTFS;
/*
//***************************************************
//* UPDATING IA AND IACHASTA FILES ON DISK *
//***************************************************
//* IGNORE ERROR MESSAGE IF IA FEATURE IS *
//* NOT AVAILABLE *
//***************************************************
/*
<DISP IAFEAT;
/*
<TRANS BUFFER:TYPE=AMA;
<TRANS BUFFER:TYPE=FIR;
<TRANS BUFFER:TYPE=IARA;
<TRANS BUFFER:TYPE=INA;
<TRANS BUFFER:TYPE=MAL;
<TRANS BUFFER:TYPE=MOB;
<TRANS BUFFER:TYPE=TOB;
<TRANS BUFFER:TYPE=TST;
<TRANS BUFFER:TYPE=UAM;
<TRANS BUFFER:TYPE=DNOB;
<TRANS BUFFER:TYPE=PMOB;
<TRANS BUFFER:TYPE=ERS;
<TRANS BUFFER:TYPE=MCR;
/*
<DISP IACRG;
13-46 P30305-X1118-G499-01-7618
/*
<EDIT MET:TYPE=IACMET;
/*
//***************************************************
//* CHECK IF ALL PROJECT-SPECIFIC FILES *
//* ARE UPDATED ON DISK *
//***************************************************
/*
<RESET CFOPT;
<ENDFILE;
P30305-X1118-G499-01-7618 13-47
13.4.18. Command File CF.11.V5CHECKG499
<CMDFILE;
/* CF.11.V5CHECKG499 */
/*
/***************************************************/
/* CF-NAME : CF.11.V5CHECKG499 */
/* */
/* PURPOSE : CHECK OF V5-LINK DISTRIBUTION */
/* */
/* COPYRIGHT (C) SIEMENS AG 2005 */
/* */
/* SSP-TYPE : CP113 */
/* */
/* AUTHOR : Com CD NC CC UP */
/* */
/* REMARKS : */
/***************************************************/
/*
//***************************************************
//* COMMAND FILE CF.11.V5CHECKG499 STARTED *
//***************************************************
//* CHECKING V5-LINK DISTRIBUTION *
//***************************************************
/*
<SET CFOPT: ACKCFS=ALL,DANCMD=EXEC,ACKREQ=POS;
/*
<DISP DLUMOD: DLU=X;
<DISP V5LINK: V5IFID=X;
/*
<RESET CFOPT;
<ENDFILE;
13-48 P30305-X1118-G499-01-7618
13.5. Command Files V17/CCNC
P30305-X1118-G499-01-7618 13-49
/*
<CONF CAP: CAP=5, OST=MBL;
<SKIP CMD: ON=32, LABEL=STA;
<CONF CAP: CAP=5, OST=ACT;
<CONF CAP: CAP=5, OST=PLA;
/*
.STA<STEP;
/*
<STAT SSP;
/*
<RESET CFOPT;
//**************************************************************
//* PLEASE CHECK THE CAP STATES AND CONFIGURE, IF NECESSARY: *
//* ALL AVAILABLE CAPS MUST BE IN ACT *
//* NOT EXISTING BUT CREATED CAPS MUST BE IN PLA *
//**************************************************************
/*
<ENDFILE;
13-50 P30305-X1118-G499-01-7618
13.5.2. Command File CF.17.ACTX25G499
<CMDFILE;
/* CF.17.ACTX25G499 */
/*
/***************************************************/
/* CF-NAME : CF.17.ACTX25G499 */
/* */
/* PURPOSE : ACTIVATION OF X25-LINKS */
/* */
/* COPYRIGHT (C) SIEMENS AG 2005 */
/* */
/* SSP-TYPE : CP113 */
/* */
/* AUTHOR : Com CD NC CC UP */
/* */
/* REMARKS : X25-LINK 0...7 */
/***************************************************/
/*
//***************************************************
//* COMMAND FILE CF.17.ACTX25G499 STARTED *
//***************************************************
//* ACTIVATION OF X25-LINK 0...7 *
//***************************************************
//* IGNORE ERROR MESSAGES IF X25LINK *
//* IS NOT AVAILABLE *
//***************************************************
/*
<SET CFOPT: ACKCFS=ALL,DANCMD=EXEC,ACKREQ=POS;
/*
<ENTR ALMODE: HLIM=YES;
/*
<STAT SSP;
/*
<CONF X25LINK:X25LINK=0,OST=MBL;
<CONF X25LINK:X25LINK=0,OST=ACT;
<CONF X25LINK:X25LINK=1,OST=MBL;
<CONF X25LINK:X25LINK=1,OST=ACT;
<CONF X25LINK:X25LINK=2,OST=MBL;
<CONF X25LINK:X25LINK=2,OST=ACT;
<CONF X25LINK:X25LINK=3,OST=MBL;
<CONF X25LINK:X25LINK=3,OST=ACT;
<CONF X25LINK:X25LINK=4,OST=MBL;
<CONF X25LINK:X25LINK=4,OST=ACT;
<CONF X25LINK:X25LINK=5,OST=MBL;
<CONF X25LINK:X25LINK=5,OST=ACT;
<CONF X25LINK:X25LINK=6,OST=MBL;
<CONF X25LINK:X25LINK=6,OST=ACT;
<CONF X25LINK:X25LINK=7,OST=MBL;
<CONF X25LINK:X25LINK=7,OST=ACT;
/*
<STAT SSP;
//***************************************************
//* AVAILABLE X25-LINKS MUST BE IN ACT *
//* IF NOT ACTIVATE X25-LINKS *
//***************************************************
/*
<RESET CFOPT;
<ENDFILE;
P30305-X1118-G499-01-7618 13-51
13.5.3. Command File CF.17.CRSUUCTG499
<CMDFILE;
/* CF.17.CRSUUCTG499 */
/*
/***************************************************/
/* CF-NAME : CF.17.CRSUUCTG499 */
/* */
/* PURPOSE : CREATION OF FILE SU.UCT FOR */
/* FUNCTION ISTART2F V17 */
/* */
/* COPYRIGHT (C) SIEMENS AG 2005 */
/* */
/* SSP-TYPE : CP113 */
/* */
/* AUTHOR : Com CD NC CC UP */
/* */
/* REMARKS : */
/***************************************************/
/*
//***************************************************
//* COMMAND FILE CF.17.CRSUUCTG499 STARTED *
//***************************************************
//* CREATING FILE SU.UCT FOR FUNCTION ISTART2F V17 *
//***************************************************
/*
<SET CFOPT: ACKCFS=ALL,DANCMD=EXEC,ACKREQ=POS;
/*
<DISP FILE: FILE=SU.;
<DEL FILE: FILE=SU.UCT.TEMP;
<DACT SYSUPG;
/*
<EXEC EDTS8;
*1
*I
*1
*XXXXXXXXXXXXXXXXX
*.
*W SU.UCT.TEMP
*END
/*
<TRANS FILE: FILE=SU.UCT/SU.UCT.TEMP, MODE=CRD;
/*
<DEL FILE: FILE=SU.UCT.TEMP;
/*
<DISP FILE: FILE=SU.;
<DISP FILETEXT: FILE=SU.UCT;
/*
<ENDFILE;
13-52 P30305-X1118-G499-01-7618
13.5.4. Command File CF.17.DIAGMB0G499
<CMDFILE;
/* CF.17.DIAGMB0G499 */
/*
/***************************************************/
/* CF-NAME : CF.17.DIAGMB0G499 */
/* */
/* PURPOSE : DIAGNOSIS OF MB-0 */
/* */
/* COPYRIGHT (C) SIEMENS AG 2005 */
/* */
/* SSP-TYPE : CP113 */
/* */
/* AUTHOR : Com CD NC CC UP */
/* */
/* REMARKS : FOR MB CAPACITY STAGE UP TO DE54 */
/***************************************************/
/*
//***************************************************
//* COMMAND FILE CF.17.DIAGMB0G499 STARTED *
//***************************************************
/*
<SET CFOPT: ACKCFS=ALL, DANCMD=EXEC, ACKREQ=POS, OFF=16;
/*
//***************************************************
//* DIAGNOSIS OF MB-0 *
//***************************************************
/*
<DISP EXDDAT;
<STAT SSP;
<STAT MB;
<STAT SN;
/*
<CONF MB: MB=0,OST=MBL;
<SKIP CMD: ON=32, LABEL=ERR;
<DIAG MB: MB=0;
<SKIP CMD: ON=32, LABEL=ERR;
/*
<CONF IOP:IOP=IOPMB-32,OST=MBL;
<SKIP CMD: ON=32, LABEL=ERR;
/*
//***************************************************
//* AVAILABILITY OF IOPMB-34 *
//* DEPENDS ON EXCHANGE TYPE AND NO. OF LTG *
//***************************************************
/*
<CONF IOP:IOP=IOPMB-34,OST=MBL;
/*
//***************************************************
//* AVAILABILITY OF IOPMB-36 AND 38 *
//* DEPENDS ON EXCHANGE TYPE AND NO. OF LTG *
//***************************************************
/*
<CONF IOP:IOP=IOPMB-36,OST=MBL;
<CONF IOP:IOP=IOPMB-38,OST=MBL;
/*
<DIAG MB: MB=0;
<SKIP CMD: ON=32, LABEL=ERR;
/*
<CONF MB: MB=0,OST=ACT;
<SKIP CMD: ON=32, LABEL=ERR;
/*
<CONF IOP:IOP=IOPMB-32,OST=ACT;
<SKIP CMD: ON=32, LABEL=ERR;
P30305-X1118-G499-01-7618 13-53
/*
<CONF IOP:IOP=IOPMB-34,OST=ACT;
<CONF IOP:IOP=IOPMB-36,OST=ACT;
<CONF IOP:IOP=IOPMB-38,OST=ACT;
/*
<STAT SSP;
<STAT MB;
<STAT SN;
/*
<RESET CFOPT;
//******************************************************
//* PLEASE CHECK FOR FAULTS AND IF MB-0,1, SN-0,1 *
//* AND IOPMBS ARE IN ACT *
//******************************************************
<ENDFILE;
/*
.ERR<STEP;
<SET CFOPT: ON=16, SCOPE=GLOBAL;
//*******************************************************
//* C O M M A N D N O T E X E C U T E D *
//*******************************************************
//* ELIMINATE FAULT AND ENTER NOT EXECUTED COMMANDS *
//*******************************************************
<ENDFILE;
13-54 P30305-X1118-G499-01-7618
13.5.5. Command File CF.17.DIAGMB1G499
<CMDFILE;
/* CF.17.DIAGMB1G499 */
/*
/***************************************************/
/* CF-NAME : CF.17.DIAGMB1 G499 */
/* */
/* PURPOSE : DIAGNOSIS OF MB-1 */
/* */
/* COPYRIGHT (C) SIEMENS AG 2005 */
/* */
/* SSP-TYPE : CP113 */
/* */
/* AUTHOR : Com CD NC CC UP */
/* */
/* REMARKS : FOR MB CAPACITY STAGE UP TO DE54 */
/***************************************************/
/*
//***************************************************
//* COMMAND FILE CF.17.DIAGMB1G499 STARTED *
//***************************************************
/*
<SET CFOPT: ACKCFS=ALL, DANCMD=EXEC, ACKREQ=POS, OFF=16;
/*
//***************************************************
//* DIAGNOSIS OF MB-1 *
//***************************************************
/*
<DISP EXDDAT;
<STAT SSP;
<STAT MB;
<STAT SN;
/*
<CONF MB: MB=1,OST=MBL;
<SKIP CMD: ON=32, LABEL=ERR;
<DIAG MB: MB=1;
<SKIP CMD: ON=32, LABEL=ERR;
/*
<CONF IOP:IOP=IOPMB-33,OST=MBL;
<SKIP CMD: ON=32, LABEL=ERR;
/*
//***************************************************
//* AVAILABILITY OF IOPMB-35 *
//* DEPENDS ON EXCHANGE TYPE AND NO. OF LTG *
//***************************************************
/*
<CONF IOP:IOP=IOPMB-35,OST=MBL;
/*
//***************************************************
//* AVAILABILITY OF IOPMB-37 AND 39 *
//* DEPENDS ON EXCHANGE TYPE AND NO. OF LTG *
//***************************************************
/*
<CONF IOP:IOP=IOPMB-37,OST=MBL;
<CONF IOP:IOP=IOPMB-39,OST=MBL;
/*
<DIAG MB: MB=1;
<SKIP CMD: ON=32, LABEL=ERR;
/*
<CONF MB: MB=1,OST=ACT;
<SKIP CMD: ON=32, LABEL=ERR;
/*
<CONF IOP:IOP=IOPMB-33,OST=ACT;
P30305-X1118-G499-01-7618 13-55
<SKIP CMD: ON=32, LABEL=ERR;
/*
<CONF IOP:IOP=IOPMB-35,OST=ACT;
<CONF IOP:IOP=IOPMB-37,OST=ACT;
<CONF IOP:IOP=IOPMB-39,OST=ACT;
/*
<STAT SSP;
<STAT MB;
<STAT SN;
/*
<RESET CFOPT;
//******************************************************
//* PLEASE CHECK FOR FAULTS AND IF MB-0,1, SN-0,1 *
//* AND IOPMBS ARE IN ACT *
//******************************************************
<ENDFILE;
/*
.ERR<STEP;
<SET CFOPT: ON=16, SCOPE=GLOBAL;
//*******************************************************
//* C O M M A N D N O T E X E C U T E D *
//*******************************************************
//* ELIMINATE FAULT AND ENTER NOT EXECUTED COMMANDS *
//*******************************************************
<ENDFILE;
13-56 P30305-X1118-G499-01-7618
13.5.6. Command File CF.17.DIUSTATG499
<CMDFILE;
/* CF.17.DIUSTATG499 */
/*
/***************************************************/
/* CF-NAME : CF.17.DIUSTATG499 */
/* */
/* PURPOSE : INQUIRY DIU AND CR STATUS */
/* */
/* COPYRIGHT (C) SIEMENS AG 2005 */
/* */
/* SSP-TYPE : CP113 */
/* */
/* AUTHOR : Com CD NC CC UP */
/* */
/* REMARKS : */
/***************************************************/
/*
//***************************************************
//* COMMAND FILE CF.17.DIUSTATG499 STARTED *
//***************************************************
//* INQUIRY OF DIU AND CR STATUS *
//***************************************************
/*
<SET CFOPT: ACKCFS=ALL,DANCMD=EXEC,ACKREQ=POS, OFF=16;
/*
//********************************************/
//* INQUIRY OF DIU IN ACT */
//********************************************/
<STAT DIU: LTG=X-X, OST=ACT;
/*
//********************************************/
//* INQUIRY OF DIU IN CBL */
//********************************************/
<STAT DIU: LTG=X-X, OST=CBL;
/*
//********************************************/
//* INQUIRY OF DIU IN MBL */
//********************************************/
<STAT DIU: LTG=X-X, OST=MBL;
/*
//********************************************/
//* INQUIRY OF DIU IN PLA */
//********************************************/
<STAT DIU: LTG=X-X, OST=PLA;
/*
//********************************************/
//* INQUIRY OF CR IN ACT */
//********************************************/
<STAT CR: LTG=X-X, OST=ACT;
/*
//********************************************/
//* INQUIRY OF CR IN MBL */
//********************************************/
<STAT CR: LTG=X-X, OST=MBL;
/*
//********************************************/
//* INQUIRY OF CR IN PLA */
//********************************************/
<STAT CR: LTG=X-X, OST=PLA;
/*
<RESET CFOPT;
<ENDFILE;
P30305-X1118-G499-01-7618 13-57
13.5.7. Command File CF.17.MBSNPLAG499
<CMDFILE;
/* CF.17.MBSNPLAG499 */
/*
/***************************************************/
/* CF-NAME : CF.17.MBSNPLAG499 */
/* */
/* PURPOSE : CONFIGURATION OF MB AND SN */
/* TO PLA,SIDE 0 */
/* */
/* COPYRIGHT (C) SIEMENS AG 2005 */
/* */
/* SSP-TYPE : CP113 */
/* */
/* AUTHOR : Com CD NC CC UP */
/* */
/* REMARKS : CAPACITY STAGE IS UP TO SN:504LTG*/
/***************************************************/
/*
//***************************************************
//* COMMAND FILE CF.17.MBSNPLAG499 STARTED *
//***************************************************
//* CONFIGURATION OF MB AND SN TO PLA *
//* CAPACITY STAGE IS UP TO SN:504LTG *
//***************************************************
/*
<SET CFOPT: ACKCFS=ALL,DANCMD=EXEC,ACKREQ=POS;
/*
<DISP EXDDAT;
/*
//***************************************************
//* CONFIGURATION OF SN TO MBL *
//***************************************************
//***************************************************
//* IGNORE ERROR MESSAGE FOR UNITS NOT AVAILABLE *
//***************************************************
/*
<STAT SN;
/*
<CONF TSG: SN=0, TSG=0, OST=MBL;
<CONF TSG: SN=0, TSG=1, OST=MBL;
<CONF TSG: SN=0, TSG=2, OST=MBL;
<CONF TSG: SN=0, TSG=3, OST=MBL;
<CONF TSG: SN=0, TSG=4, OST=MBL;
<CONF TSG: SN=0, TSG=5, OST=MBL;
<CONF TSG: SN=0, TSG=6, OST=MBL;
<CONF TSG: SN=0, TSG=7, OST=MBL;
/*
<CONF SSG: SN=0, SSG=0, OST=MBL;
<CONF SSG: SN=0, SSG=1, OST=MBL;
<CONF SSG: SN=0, SSG=2, OST=MBL;
<CONF SSG: SN=0, SSG=3, OST=MBL;
/*
//***************************************************
//* CONFIGURATION OF MB TO MBL *
//***************************************************
//***************************************************
//* IGNORE ERROR MESSAGE FOR UNITS NOT AVAILABLE *
//***************************************************
/*
<STAT MB;
/*
<CONF MBUL: MB=0, MBUL=0, OST=MBL;
<CONF MBUL: MB=0, MBUL=1, OST=MBL;
13-58 P30305-X1118-G499-01-7618
<CONF MBUL: MB=0, MBUL=2, OST=MBL;
<CONF MBUL: MB=0, MBUL=3, OST=MBL;
<CONF MBUL: MB=0, MBUL=4, OST=MBL;
<CONF MBUL: MB=0, MBUL=5, OST=MBL;
<CONF MBUL: MB=0, MBUL=6, OST=MBL;
<CONF MBUL: MB=0, MBUL=7, OST=MBL;
/*
<CONF MBUS: MB=0, MBUS=0, OST=MBL;
<CONF MBUS: MB=0, MBUS=1, OST=MBL;
<CONF MBUS: MB=0, MBUS=2, OST=MBL;
<CONF MBUS: MB=0, MBUS=3, OST=MBL;
/*
//***************************************************
//* CONFIGURATION OF SN TO PLA *
//***************************************************
//***************************************************
//* IGNORE ERROR MESSAGE FOR UNITS NOT AVAILABLE *
//***************************************************
/*
<CONF TSG: SN=0, TSG=0, OST=PLA;
<CONF TSG: SN=0, TSG=1, OST=PLA;
<CONF TSG: SN=0, TSG=2, OST=PLA;
<CONF TSG: SN=0, TSG=3, OST=PLA;
<CONF TSG: SN=0, TSG=4, OST=PLA;
<CONF TSG: SN=0, TSG=5, OST=PLA;
<CONF TSG: SN=0, TSG=6, OST=PLA;
<CONF TSG: SN=0, TSG=7, OST=PLA;
/*
<CONF SSG: SN=0, SSG=0, OST=PLA;
<CONF SSG: SN=0, SSG=1, OST=PLA;
<CONF SSG: SN=0, SSG=2, OST=PLA;
<CONF SSG: SN=0, SSG=3, OST=PLA;
/*
//***************************************************
//* CONFIGURATION OF MB TO PLA *
//***************************************************
//***************************************************
//* IGNORE ERROR MESSAGE FOR UNITS NOT AVAILABLE *
//***************************************************
/*
<CONF MBUL: MB=0, MBUL=0, OST=PLA;
<CONF MBUL: MB=0, MBUL=1, OST=PLA;
<CONF MBUL: MB=0, MBUL=2, OST=PLA;
<CONF MBUL: MB=0, MBUL=3, OST=PLA;
<CONF MBUL: MB=0, MBUL=4, OST=PLA;
<CONF MBUL: MB=0, MBUL=5, OST=PLA;
<CONF MBUL: MB=0, MBUL=6, OST=PLA;
<CONF MBUL: MB=0, MBUL=7, OST=PLA;
/*
<CONF MBUS: MB=0, MBUS=0, OST=PLA;
<CONF MBUS: MB=0, MBUS=1, OST=PLA;
<CONF MBUS: MB=0, MBUS=2, OST=PLA;
<CONF MBUS: MB=0, MBUS=3, OST=PLA;
/*
<STAT MB;
/*
//***************************************************
//* CHECK MB STATUS *
//* ALL AVAILABLE MB-UNITS MUST HAVE STATUS PLA *
//***************************************************
/*
<STAT SN;
/*
//***************************************************
//* CHECK SN STATUS *
//* ALL AVAILABLE SN-UNITS MUST HAVE STATUS PLA *
P30305-X1118-G499-01-7618 13-59
//***************************************************
/*
<RESET CFOPT;
<ENDFILE;
13-60 P30305-X1118-G499-01-7618
13.5.8. Command File CF.17.HEXIOCAG499
<CMDFILE;
/* CF.17.HEXIOCAG499 */
/*
/***************************************************/
/* CF-NAME : CF.17.HEXIOCAG499 */
/* */
/* PURPOSE : INQUIRY OF SEMIPERMANENT STATUS */
/* TABLE OF IOC-2,3 AND CAPS V17 */
/* */
/* COPYRIGHT (C) SIEMENS AG 2005 */
/* */
/* SSP-TYPE : CP113 */
/* */
/* AUTHOR : Com CD NC CC UP */
/* */
/* REMARKS : */
/***************************************************/
/*
//***************************************************
//* COMMAND FILE CF.17.HEXIOCAG499 STARTED *
//***************************************************
//* INQUIRY OF SEMIP.STATUS TABLE IOC-2,3,CAPS V17 *
//***************************************************
/*
<SET CFOPT: ACKCFS=ALL,DANCMD=EXEC,ACKREQ=POS;
/*
<DMP CPIMDMP: PLF=BAPM, ADDR="APSCMY00.BBSCPA0C.ZCDA2A0P"
#&&"+H'20";
/*
<RESET CFOPT;
<ENDFILE;
P30305-X1118-G499-01-7618 13-61
13.5.9. Command File CF.17.HEXLTGG499
<CMDFILE;
/* CF.17.HEXLTGG499 */
/*
/***************************************************/
/* CF-NAME : CF.17.HEXLTGG499 */
/* */
/* PURPOSE : INQUIRY OF SEMIPERMANENT STATUS */
/* TABLE OF LTG V17 */
/* */
/* COPYRIGHT (C) SIEMENS AG 2005 */
/* */
/* SSP-TYPE : CP113 */
/* */
/* AUTHOR : Com CD NC CC UP */
/* */
/* REMARKS : FOR SN STAGE DE4 UP TO DE54 */
/***************************************************/
/*
//***************************************************
//* COMMAND FILE CF.17.HEXLTGG499 STARTED *
//***************************************************
//* INQUIRY OF SEMIPERMANENT STATUS TABLE LTG V17 *
//***************************************************
/*
<SET CFOPT: ACKCFS=ALL,DANCMD=EXEC,ACKREQ=POS;
/*
//***************************************************
//* INQUIRY OF CREATED LTGS *
//***************************************************
<DISP LTG: LTG=X-X;
/*
/*
//***************************************************
//* INQUIRY OF STATUS TABLE LTG *
//***************************************************
<DMP CPIMDMP: PLF=BAPM, ADDR="APSCMY00.BBSCPA0C.LTGDAA3P
#+H'27140"&&"+H'180";
/*
<RESET CFOPT;
<ENDFILE;
13-62 P30305-X1118-G499-01-7618
13.5.10. Command File CF.17.HEXMBBG499
<CMDFILE;
/* CF.17.HEXMBBG499 */
/*
/***************************************************/
/* CF-NAME : CF.17.HEXMBBG499 */
/* LONG-NAME : INQUIRY OF SEMIPERMANENT STATUS */
/* TABLE OF MBB IN V17 */
/* */
/* COPYRIGHT (C) SIEMENS AG 2005 */
/* */
/* SSP-TYPE : CP113 */
/* */
/* AUTHOR : Com CD NC CC UP */
/* */
/* PURPOSE : INQUIRY SEMIPERMANENT STATUS */
/* TABLE OF MBB IN V17 */
/***************************************************/
//***************************************************
//* COMMAND FILE CF.17.HEXMBBG499 STARTED *
//* *
//* INQUIRY OF SEMIPER. STATUS TABLE MB IN V17 *
//***************************************************
/*
<SET CFOPT: ACKCFS=ALL,DANCMD=EXEC,ACKREQ=POS, OFF=16;
/*
/*
//********************************************/
//* INQUIRY OF STATUS TABLE MBB */
//********************************************/
<DMP CPIMDMP: PLF=BAPM, ADDR="APSCMY00.BBSCPA0C.MEBDAA3P"
#&&"+H'180";
/*
/*
<RESET CFOPT;
<ENDFILE;
P30305-X1118-G499-01-7618 13-63
13.5.11. Command File CF.17.HEXMBDG499
<CMDFILE;
/* CF.16.HEXMBDG499 */
/*
/***************************************************/
/* CF-NAME : CF.16.HEXMBDG499 */
/* LONG-NAME : INQUIRY OF SEMIPERMANENT STATUS */
/* TABLE OF MBD IN V17 */
/* */
/* COPYRIGHT (C) SIEMENS AG 2005 */
/* */
/* SSP-TYPE : CP113 */
/* */
/* AUTHOR : Com CD NC CC UP */
/* */
/* PURPOSE : INQUIRY SEMIPERMANENT STATUS */
/* TABLE OF MBD IN V17 */
/***************************************************/
//***************************************************
//* COMMAND FILE CF.16.HEXMBDG499 STARTED *
//* *
//*INQUIRY OF SEMIPERMANENT STATUS TABLE MBD IN V17 *
//***************************************************
/*
<SET CFOPT: ACKCFS=ALL,DANCMD=EXEC,ACKREQ=POS, OFF=16;
/*
//********************************************/
//* INQUIRY OF STATUS TABLE MBD */
//********************************************/
<DMP CPIMDMP: PLF=BAPM, ADDR="APSCMY00.BBSCPA0C.MEBDAA3P"
#&&"+H'100";
/*
<RESET CFOPT;
<ENDFILE;
13-64 P30305-X1118-G499-01-7618
13.5.12. Command File CF.17.HEXSNBG499
<CMDFILE;
/* CF.16.HEXSNBG499 */
/*
/***************************************************/
/* CF-NAME : CF.16.HEXSNBG499 */
/* LONG-NAME : INQUIRY OF SEMIPERMANENT STATUS */
/* TABLE OF SN IN V17 */
/* */
/* COPYRIGHT (C) SIEMENS AG 2005 */
/* */
/* SSP-TYPE : CP113 */
/* */
/* AUTHOR : Com CD NC CC UP */
/* */
/* PURPOSE : INQUIRY SEMIPERMANENT STATUS */
/* TABLE OF SN IN V17 */
/***************************************************/
//***************************************************
//* COMMAND FILE CF.16.HEXSNBG499 STARTED *
//* *
//* INQUIRY OF SEMIPERMANENT STATUS TABLE SN V17 *
//***************************************************
/*
<SET CFOPT: ACKCFS=ALL,DANCMD=EXEC,ACKREQ=POS, OFF=16;
/*
//********************************************/
//* INQUIRY OF STATUS TABLE SNB */
//********************************************/
<DMP CPIMDMP: PLF=BAPM, ADDR="APSCMY00.BBSCPA0C.SINDAA3P
#+H'0804"&&"+H'180";
/*
<RESET CFOPT;
<ENDFILE;
P30305-X1118-G499-01-7618 13-65
13.5.13. Command File CF.17.OPERMAXG499
<CMDFILE;
/* CF.17.OPERMAXG499 */
/*
/***************************************************/
/* CF-NAME : CF.17.OPERMAXG499 */
/* */
/* PURPOSE : EXPANSION OF FILE SG.OPER */
/* */
/* COPYRIGHT (C) SIEMENS AG 2005 */
/* */
/* SSP-TYPE : CP113 */
/* */
/* AUTHOR : Com CD NC CC UP */
/* */
/* REMARKS : */
/***************************************************/
/*
//***************************************************
//* COMMAND FILE CF.17.OPERMAXG499 STARTED *
//***************************************************
//* EXPANSION OF FILE SG.OPER *
//***************************************************
/*
<SET CFOPT: ACKCFS=ALL,DANCMD=EXEC,ACKREQ=POS;
/*
<DMP SGMSG;
<CAN AFILE: AFILE=SG.OPER;
<CR AFILE: AFILE=SG.OPER, SIZE=1800, TYPE=DOUBLE,
#THRU=50-75-100,
#THRD=50-75-100,
#THRF=NOALARM-NOALARM-NOALARM;
<DISP AFILE: AFILE=SG.OPER;
<DISP FILE: FILE=SG.OPER;
<DISP FILE: FILE=SG.OPER, ALL;
/*
<RESET CFOPT;
<ENDFILE;
13-66 P30305-X1118-G499-01-7618
13.5.14. Command File CF.17.OPERMING499
<CMDFILE;
/* CF.17.OPERMING499 */
/*
/***************************************************/
/* CF-NAME : CF.17.OPERMING499 */
/* */
/* PURPOSE : REDUCTION OF FILE SG.OPER */
/* */
/* COPYRIGHT (C) SIEMENS AG 2005 */
/* */
/* SSP-TYPE : CP113 */
/* */
/* AUTHOR : Com CD NC CC UP */
/* */
/* REMARKS : */
/***************************************************/
/*
//***************************************************
//* COMMAND FILE CF.17.OPERMING499 STARTED *
//***************************************************
//* REDUCTION OF FILE SG.OPER *
//***************************************************
/*
<SET CFOPT: ACKCFS=ALL,DANCMD=EXEC,ACKREQ=POS;
/*
<CAN AFILE: AFILE=SG.OPER;
<CR AFILE: AFILE=SG.OPER, SIZE=900, TYPE=DOUBLE,
#THRU=50-75-100,
#THRD=50-75-100,
#THRF=NOALARM-NOALARM-NOALARM;
<DMP SGMSG;
<DISP AFILE: AFILE=SG.OPER;
<DISP FILE: FILE=SG.OPER;
<DISP FILE: FILE=SG.OPER, ALL;
/*
<RESET CFOPT;
<ENDFILE;
P30305-X1118-G499-01-7618 13-67
13.5.15. Command File CF.17.PLACSCG499
<CMDFILE;
/* CF.17.PLACSCG499 */
/*
/***************************************************/
/* CF-NAME : CF.17.PLACSCG499 */
/* */
/* LONG-NAME : CONFIGURATION OF CSC-LINKS */
/* TO PLA */
/* */
/* COPYRIGHT (C) SIEMENS AG 2005 */
/* */
/* SSP-TYPE : CP113 */
/* */
/* AUTHOR : Com CD NC CC UP */
/* */
/* PURPOSE : CONFIGURATION OF CSC-LINKS */
/* TO PLA: */
/* CSC-0 UP TO CSC-3 */
/***************************************************/
/*
<SET CFOPT: ACKCFS=ALL,DANCMD=EXEC,ACKREQ=POS;
/*
//***************************************************
//* COMMANDFILE CF.17.PLACSCG499 STARTED *
//***************************************************
//***************************************************
//* CONFIGURATION OF CSC-LINKS TO PLA: *
//* CSC-0 UP TO 3 *
//***************************************************
//***************************************************
//* IGNORE ERROR MESSAGE FOR NOT AVAILABLE *
//* CSC-LINKS *
//***************************************************
/*
<STAT SSP;
/*
<CONF CSC:CSC=0,OST=MBL;
<CONF CSC:CSC=0,OST=PLA;
<CONF CSC:CSC=1,OST=MBL;
<CONF CSC:CSC=1,OST=PLA;
<CONF CSC:CSC=2,OST=MBL;
<CONF CSC:CSC=2,OST=PLA;
<CONF CSC:CSC=3,OST=MBL;
<CONF CSC:CSC=3,OST=PLA;
/*
<STAT SSP;
/*
//***************************************************
//* COMMANDFILE FINISHED *
//***************************************************
//***************************************************
//* CHECK STATUS OF CSC-LINKS: *
//* ALL AVAILABLE CSC-LINKS IN PLA *
//***************************************************
//***************************************************
//* IF NECESSARY CONFIGURE CSC-LINKS MANUALLY *
//***************************************************
/*
<RESET CFOPT;
<ENDFILE;
13-68 P30305-X1118-G499-01-7618
13.5.16. Command File CF.17.PLAX25G499
<CMDFILE;
/* CF.17.PLAX25G499 */
/*
/***************************************************/
/* CF-NAME : CF.17.PLAX25G499 */
/* */
/* PURPOSE : CONFIGURATION OF X25-LINKS */
/* TO PLA */
/* */
/* COPYRIGHT (C) SIEMENS AG 2005 */
/* */
/* SSP-TYPE : CP113 */
/* */
/* AUTHOR : Com CD NC CC UP */
/* */
/* REMARKS : X25-LINK 0...7 */
/***************************************************/
/*
//***************************************************
//* COMMAND FILE CF.17.PLAX25G499 STARTED *
//***************************************************
//* CONFIGURATION OF X25-LINK 0..7 TO PLA *
//***************************************************
//***************************************************
//* IGNORE ERROR MESSAGES IF X25-LINK *
//* IS NOT AVAILABLE *
//***************************************************
/*
<SET CFOPT: ACKCFS=ALL,DANCMD=EXEC,ACKREQ=POS;
/*
<CONF X25LINK:X25LINK=0,OST=MBL;
<CONF X25LINK:X25LINK=0,OST=PLA;
<CONF X25LINK:X25LINK=1,OST=MBL;
<CONF X25LINK:X25LINK=1,OST=PLA;
<CONF X25LINK:X25LINK=2,OST=MBL;
<CONF X25LINK:X25LINK=2,OST=PLA;
<CONF X25LINK:X25LINK=3,OST=MBL;
<CONF X25LINK:X25LINK=3,OST=PLA;
<CONF X25LINK:X25LINK=4,OST=MBL;
<CONF X25LINK:X25LINK=4,OST=PLA;
<CONF X25LINK:X25LINK=5,OST=MBL;
<CONF X25LINK:X25LINK=5,OST=PLA;
<CONF X25LINK:X25LINK=6,OST=MBL;
<CONF X25LINK:X25LINK=6,OST=PLA;
<CONF X25LINK:X25LINK=7,OST=MBL;
<CONF X25LINK:X25LINK=7,OST=PLA;
/*
<STAT SSP;
/*
//***************************************************
//* CHECK STATUS OF X25-LINKS *
//* X25-LINK 0...7 MUST BE IN PLA *
//***************************************************
/*
<RESET CFOPT;
<ENDFILE;
P30305-X1118-G499-01-7618 13-69
13.5.17. Command File CF.17.PROG499
<CMDFILE;
/* CF.17.PROG499*/
/*
/***************************************************/
/* CF-NAME : CF.17.PROG499 */
/* */
/* PURPOSE : START OF PROCESSES IN */
/* INSTALLATION RECOVERY V17 */
/* */
/* COPYRIGHT (C) SIEMENS AG 2005 */
/* */
/* SSP-TYPE : CP113 */
/* */
/* AUTHOR : Com CD NC CC UP */
/* */
/* REMARKS : */
/***************************************************/
/*
//***************************************************
//* COMMAND FILE CF.17.PROG499 STARTED *
//***************************************************
//* STARTING PROCESSES IN INSTALLATION RECOVERY V17 *
//***************************************************
/*
<SET CFOPT: ACKCFS=ALL, DANCMD=EXEC, ACKREQ=POS;
<START OM: APPL=Q3IF;
<START DB;
<START PROCESS: NAME=ICSRV;
/*
<START PROCESS: NAME=CLTLM;
/*
<START PROCESS: NAME=QACEN;
/*
<START PROCESS: NAME=GAILS;
/*
<START PROCESS: NAME=JIAUP;
/*
<START PROCESS: NAME=ASCEX;
/*
<START PROCESS: NAME=MMILF;
/*
<START PROCESS: NAME=MEINI;
/*
//***********************************************/
//* O K A Y */
//***********************************************/
/*
<RESET CFOPT;
<ENDFILE;
13-70 P30305-X1118-G499-01-7618
13.5.18. Command File CF.17.SYSTATG499
<CMDFILE;
/* CF.17.SYSTATG499 */
/*
/***************************************************/
/* CF-NAME : CF.17.SYSTATG499 */
/* */
/* PURPOSE : INQUIRY OF SYSTEM STATUS */
/* */
/* COPYRIGHT (C) SIEMENS AG 2005 */
/* */
/* SSP-TYPE : CP113 */
/* */
/* AUTHOR : Com CD NC CC UP */
/* */
/* REMARKS : */
/***************************************************/
/*
//***************************************************
//* COMMAND FILE CF.17.SYSTATG499 STARTED *
//***************************************************
//* INQUIRY OF SYSTEM STATUS *
//***************************************************
/*
<SET CFOPT: ACKCFS=ALL,DANCMD=EXEC,ACKREQ=POS;
/*
//********************************************
//* INQUIRY OF UPDATE STATUS *
//********************************************
<DISP SPLITOPT;
<DISP UPDATE;
<STAT LOG;
/*
//********************************************
//* INQUIRY OF DISK CONTENTS *
//********************************************
<DISP FILE;
<DISP MD;
<DISP GEN;
/*
/*
//********************************************
//* INQUIRY OF SYSTEM REDUNDANCY *
//********************************************
<STAT SSP;
<STAT MB;
<STAT SN;
<DISP SNDAT;
<STAT CCG;
<DISP CCG;
<STAT SYP;
<DISP LTG: LTG=X-X;
<STAT LTG: LTG=X-X;
<DISP DLU: DLU=X;
<STAT DLU: DLU=X;
<STAT DIU: LTG=X-X, OST=UNA;
<STAT CR: LTG=X-X, OST=UNA;
/*
/*
P30305-X1118-G499-01-7618 13-71
//********************************************
//* INQUIRY OF CCNC STATUS *
//********************************************
<STAT CCNC: UNIT=CCNP-X;
<STAT CCNC: UNIT=SIPA-X;
<STAT CCNC: UNIT=SILTC-X;
<STAT CCNC: UNIT=MUXM-X;
<STAT CCNC: UNIT=SILT-X;
/*
<DISP C7LINK: LSNAM=X;
<DISP C7LSET: LSNAM=X;
<DISP C7DP: DPC=X, NETIND=NAT0;
<DISP NUC;
/*
//********************************************
//* INQUIRY OF EXCHANGE DATA *
//********************************************
<DISP EXDDAT;
<STAT V5LINK: V5IFID=X, OST=ACT;
<DISP OUTSUP;
<DISP IAFEAT;
<DISP IAOPT;
<DISP METSAV;
<DISP SSPRT;
/*
//**********************************************
//* CHECK INTERROGATION RESULTS *
//**********************************************
//* IF NECESSARY CREATE REQUIRED CONFIGURATION *
//**********************************************
/*
<RESET CFOPT;
<ENDFILE;
13-72 P30305-X1118-G499-01-7618
13.5.19. Command File CF.17.UPDFILEG499
<CMDFILE;
/* CF.17.UPDFILEG499 */
/*
/***************************************************/
/* CF-NAME : CF.17.UPDFILEG499 */
/* */
/* LONG-NAME : UPDATING CHARGE FILES ON MDD */
/* */
/* COPYRIGHT (C) SIEMENS AG 2005 */
/* */
/* SSP-TYPE : CP113 */
/* */
/* AUTHOR : Com CD NC CC UP */
/* */
/* PURPOSE : UPDATING CHARGE FILES ON MDD: */
/* CA-,IA- AND IACHASTA */
/***************************************************/
/*
<SET CFOPT: ACKCFS=ALL,DANCMD=EXEC,ACKREQ=POS;
/*
//***************************************************
//* COMMANDFILE CF.17.UPDFILEG499 STARTED *
//***************************************************
//***************************************************
//* UPDATING CHARGE FILES ON MDD *
//***************************************************
/*
//************************************************
//* SAVING CA-CHARGING DATA *
//************************************************
/*
<DISP EXDDAT;
/*
<SAVE MET;
/*
//************************************************
//* SAVING IA-CHARGING DATA *
//************************************************
//* IGNORE ERROR MESSAGE FOR NOT AVAILABLE *
//* IA-TYPE *
//************************************************
/*
<DISP IAFEAT;
/*
<TRANS BUFFER:TYPE=AMA;
<TRANS BUFFER:TYPE=DNOB;
<TRANS BUFFER:TYPE=FIR;
<TRANS BUFFER:TYPE=IARA;
<TRANS BUFFER:TYPE=INA;
<TRANS BUFFER:TYPE=MAL;
<TRANS BUFFER:TYPE=MCR;
<TRANS BUFFER:TYPE=MOB;
<TRANS BUFFER:TYPE=PMOB;
<TRANS BUFFER:TYPE=TOB;
<TRANS BUFFER:TYPE=TST;
<TRANS BUFFER:TYPE=UAM;
/*
//************************************************
//* SAVING IACHASTA-CHARGING DATA *
//************************************************
//* IGNORE ERROR MESSAGE FOR NOT AVAILABLE *
//* IACHASTA-TYPE *
//************************************************
P30305-X1118-G499-01-7618 13-73
/*
//************************************************
//* SAVING IACHASTA-CHARGING DATA *
//************************************************
//* IGNORE ERROR MESSAGE FOR NOT AVAILABLE *
//* IACHASTA-TYPE *
//************************************************
/*
<DISP IACRG;
/*
<EDIT MET:TYPE=IACMET;
/*
//*************************************************
//* COMMANDFILE FINISHED *
//*************************************************
//*************************************************
//* CHECK IF ALL CREATED CHARGE FILES HAVE *
//* BEEN UPDATED ON MDD *
//*************************************************
//*************************************************
//* IF NECESSSARY UPDATE FILES MANUALLY *
//*************************************************
/*
<RESET CFOPT;
<ENDFILE;
13-74 P30305-X1118-G499-01-7618
13.6. Patch Command Files V11
<STEP;
<SET CFOPT: ACKCFS=ERROR;
P30305-X1118-G499-01-7618 13-75
/*
.ERRORC <STEP;
// **********************************************************
// ** **
// ** ERROR DURING ENTR-,ACT- OR UPD- CPPRPCH **
// ** PATCH-ID APSLMY00.B2925L2Z.I2A1.0 WILL BE REMOVED **
// ** **
// **********************************************************
<CAN CPPRPCH: ID="APSLMY00.B2925L2Z.I2A1.0";
<STEP;
<SKIP CMD: LABEL=ERRORA, ON=32;
/*
<SET CFOPT: SCOPE=GLOBAL, ON=16;
// **********************************************************
// ** **
// ** COMMANDFILE ABORTED **
// ** PATCH-ID APSLMY00.B2925L2Z.I2A1.0 **
// ** **
// **********************************************************
<ENDFILE;
.ERRORA <STEP;
// **********************************************************
// ** **
// ** ERROR DURING CANCEL CPPRPCH **
// ** PATCH-ID APSLMY00.B2925L2Z.I2A1.0 **
// ** **
// **********************************************************
<SET CFOPT: ACKCFS=ALL;
<DISP CPPRPCH: ID="APSLMY00.B2925L2Z.I2A1.0";
<STEP;
<SET CFOPT: ACKCFS=ERROR, SCOPE=GLOBAL, ON=16;
// **********************************************************
// ** **
// ** COMMANDFILE ABORTED **
// ** PATCH-ID APSLMY00.B2925L2Z.I2A1.0 **
// ** **
// **********************************************************
<ENDFILE;
13-76 P30305-X1118-G499-01-7618
13.6.2. Patch Command File PA.11.B2925L2J
<CMDFILE;
/* PA.11.B2925L2J */
/*
/*******************************************************/
/* CF-NAME : PA.11.B2925L2J */
/* */
/* COPYRIGHT (C) SIEMENS AG 2005 */
/* */
/* SSP-TYPE : CP113 */
/* */
/* AUTHOR : Com CD NC CC UP */
/* */
/* PURPOSE : BACKOUT PATCH FOR PATCH B2925L2Z.I2A1*/
/*******************************************************/
/*
//************************************************************
//** COMMANDFILE FOR PATCH B2925L2J.I2A1 STARTED **
//************************************************************
/*
<SET CFOPT:DANCMD=EXEC,ACKREQ=POS,ACKCFS=ERROR,OFF=16;
<CAN CPPRPCH: ID="APSLMY00.B2925L2Z.I2A1.0";
<RESET CFOPT;
<ENDFILE;
P30305-X1118-G499-01-7618 13-77
13.6.3. Patch Command File PA.11.SPLITCPZ
<CMDFILE;
/* PA.11.SPLITCPZ */
/*
/*****************************************************************/
/* CF-NAME : PA.11.SPLITCPZ */
/* */
/* COPYRIGHT (C) SIEMENS AG 2005 */
/* */
/* SSP-TYPE : CP113 */
/* */
/* AUTHOR : Com CD NC CC UP */
/* */
/* PURPOSE : PATCH ENABLES SPLITSSP WITHOUT DOUBLE MDDS V11 */
/*****************************************************************/
/*
//************************************************************
//** COMMANDFILE FOR PATCH SPLITCPZ STARTED **
//************************************************************
/*
<SET CFOPT: DANCMD=EXEC, ACKREQ=POS, ACKCFS=ERROR, OFF=16;
/*
<ENTR CPPRPCH:
#ID="APSLMY00.SPLITCPZ",
#REPADDR="BBSCPA0C.PICEXS0C+H'7954",
#NEWCNT="600001E6",
#OLDCNT="0C2E0012";
<STEP;
<SKIP CMD: LABEL=ERROR0, ON=32;
/*
<ENTR CPPRPCH:
#ID="APSLMY00.SPLITCPZ",
#SUBPCHNO=1;
<STEP;
<SKIP CMD: LABEL=ERROR, ON=32;
/*
<UPD CPPRPCH: ID="APSLMY00.SPLITCPZ";
<STEP;
<SKIP CMD: LABEL=ERRORC, ON=32;
/*
<RESET CFOPT;
<ENDFILE;
/*
.ERROR0 <STEP;
//***********************************************************
//** PATCH-ID "APSLMY00.SPLITCPZ" ALREADY EXISTING OR **
//** ERROR DURING FIRST ENTR-CPPRPCH (SEE DISPLAY OUTPUT) **
//***********************************************************
<SET CFOPT: ACKCFS=ALL;
<DISP CPPRPCH: ID="APSLMY00.SPLITCPZ";
<STEP;
<SET CFOPT: ACKCFS=ERROR, SCOPE=GLOBAL, ON=16;
<ENDFILE;
/*
.ERROR <STEP;
<SET CFOPT: ACKCFS=ALL;
<DISP CPPRPCH: ID="APSLMY00.SPLITCPZ";
<STEP;
<SET CFOPT: ACKCFS=ERROR;
/*
.ERRORC <STEP;
//**********************************************************
//** ERROR DURING ENTR-,ACT- OR UPD- CPPRPCH **
//** PATCH-ID "APSLMY00.SPLITCPZ" WILL BE REMOVED **
13-78 P30305-X1118-G499-01-7618
//**********************************************************
<CAN CPPRPCH: ID="APSLMY00.SPLITCPZ";
<STEP;
<SKIP CMD: LABEL=ERRORA, ON=32;
/*
<SET CFOPT: SCOPE=GLOBAL, ON=16;
//**********************************************************
//** COMMANDFILE ABORTED **
//** PATCH-ID "APSLMY00.SPLITCPZ" **
//**********************************************************
<ENDFILE;
.ERRORA <STEP;
//**********************************************************
//** ERROR DURING CANCEL CPPRPCH **
//** PATCH-ID "APSLMY00.SPLITCPZ" **
//**********************************************************
<SET CFOPT: ACKCFS=ALL;
<DISP CPPRPCH: ID="APSLMY00.SPLITCPZ";
<STEP;
<SET CFOPT: ACKCFS=ERROR, SCOPE=GLOBAL, ON=16;
//**********************************************************
//** COMMANDFILE ABORTED **
//** PATCH-ID "APSLMY00.SPLITCPZ" **
//**********************************************************
<ENDFILE;
P30305-X1118-G499-01-7618 13-79
13.6.4. Patch Command File PA.11.SPLITCPJ
<CMDFILE;
/* PA.11.SPLITCPJ */
/*
/*****************************************************************/
/* CF-NAME : PA.11.SPLITCPJ */
/* */
/* COPYRIGHT (C) SIEMENS AG 2005 */
/* */
/* SSP-TYPE : CP113 */
/* */
/* AUTHOR : Com CD NC CC UP */
/* */
/* PURPOSE : BACKOUT PATCH FOR PATCH SPLITCPZ V11 */
/*****************************************************************/
/*
//************************************************************
//** COMMANDFILE FOR PATCH SPLITCPJ STARTED **
//************************************************************
/*
<SET CFOPT:DANCMD=EXEC,ACKREQ=POS,ACKCFS=ERROR,OFF=16;
/*
<DISP CPPRPCH: ID="APSLMY00.SPLITCPZ";
<SKIP CMD : ON=32,LABEL=PAOK;
<CAN CPPRPCH: ID="APSLMY00.SPLITCPZ";
<SKIP CMD:LABEL=ERROR,ON=32;
/*
<RESET CFOPT;
<ENDFILE;
.PAOK <STEP;
<RESET CFOPT;
//*************************************************************
//** PATCH-ID "APSLMY00.SPLITCPZ" NOT EXISTENT **
//*************************************************************
<ENDFILE;
.ERROR <STEP;
<SET CFOPT:SCOPE=GLOBAL,ON=16;
//*************************************************************
//** ERROR DURING COMMAND CAN CPPRPCH **
//** PATCH-ID "APSLMY00.SPLITCPZ" **
//*************************************************************
<ENDFILE;
13-80 P30305-X1118-G499-01-7618
13.7. Patch Command Files V17/CCNC
None
P30305-X1118-G499-01-7618 13-81
This page was left intentionally blank !
13-82 P30305-X1118-G499-01-7618
14. CHANGE REQUESTS TO THE SYSTEM UPGRADE PROCEDURE
From Name :
Project :
Date :
P30305-X1118-G499-01-7618 14-1
No. Page Line Suggested Change(s)
14-2 P30305-X1118-G499-01-7618