Professional Documents
Culture Documents
Questions of Oil Companies
Questions of Oil Companies
NAME : -------------------------------------------
NUMBER: -------------------------------------------
DATE : -------------------------------------------
RIG : -------------------------------------------
JOB : -------------------------------------------
For more exam visit this site:
www.petroleumbook.com
[1]
1- What are factors affect the penetration rates?
a) ………………………………………………
b) ………………………………………………
c) ………………………………………………
d) ………………………………………………
3- What is the maximum weight that can be used from the BHA for WOB? Why?
……………………………………………………………………………………
……………………………………………………………………………………
[2]
c) While pulling out of hole (tripping out) you got 50 bbl. gain
…………………………………………………………………………………………………
…………………………………………………………………………………………………
d) If you have stuck in salt formation
…………………………………………………………………………………………………
…………………………………………………………………………………………………
6- What is the maximum allowable over pull while POOH in vertical and horizontal well?
…………………………………………………………………………………………………
…………………………………………………………………………………………………
7- We can use separator while drilling instead of vacuum degassed? Why?
a- True b- false
Why? ………………………………………………………………………………………………
………………………………………………………………………………………………………
8- In the following table, write the effect (Increase, Decrease, Gradually increase, Gradually
decrease or No change) of each problem in each monitoring drilling parameters:
Indicator
Torque Pump pressure ROP
Problem
Poor hole cleaning
High overbalance &
permeable sands
Mobil formations
Fractured /Faulted
formations
Geo-pressured formations
Reactive formations
Unconsolidated
formations
Junk
Cement blocks
9- Top drive:
a) Type ………………… number of motors …………….. HP……………..
b) Weight of top drive ……………….. height ………………………………
c) Maximum RPM ………………………
d) Continuous torque ………………………
e) Function of wash pipe ………………………………………………………………
f) Function of IBOP & different types
…………………………………………………………………………………………
…………………………………………………………………………………………
[3]
10- How to use top drive function to make a connection?
………………………………………………………………………………………………………
……………………………………………………………………………………………………..
11- Draw-work
a) Type ……………………… HP……………………..
b) Weight …………………………….
c) Cooling system methods? And coolant fluid types?
…………………………………………………………………………………………………
………………………………………………………………………………………………....
d) Different types of brake?
………………………………………………………………………………….
………………………………………………………………………………….
………………………………………………………………………………….
………………………………………………………………………………….
12- Determine the number of barrels of cuttings drilled for one foot of 12 ¼” inch hole drilled
with 20% porosity …………………………………………………………………………………….
13- What is the idea behind drill line slip & cut program? List all steps for making slip and
cut?
………………………………………………………………………………………………
………………………………………………………………………………………………
………………………………………………………………………………………………
………………………………………………………………………………………………
………………………………………………………………………………………………
………………………………………………………………………………………………
14- 1f connection gas is noticed while drilling, what would be considered to be a good drilling
practices if an increase in mud weight is not an option at this time?
a. Flow check for longer during connection.
b. Increase drilling rate to get through zone quicker.
c. Control drilling rate to ensure only one slug of gas in annulus at any time.
d. Minimize connection time.
e. C & D.
15- Why should the well be closed in quickly after a kick has been detected?
Choose three
[4]
b. Minimize the SICP.
c. Minimize the SIDP.
d. Minimize the bottom hole press.
e. Minimize the casing shoe pressure.
16- What is the most important step in blowout prevention once a warning sign has been
detected?
a. Start circulation with pre calculated rate and kill the well with barite.
b. Shut the blowout preventer
c. Pull to the shoe quickly.
d. Call the tool pusher and company man.
e. Close the well in properly
17- 16 - If the formation pressure gradient increases from 0.60 psi/ft at 12000 ft to 0.62 psi/ft
at 12700 ft, and the mud weight is 12 ppg through the interval, the
a. Overbalance increases by about 288 psi
b. Overbalance remains constant since mud weight not changed.
c. c- Overbalance is reduced by 51 psi
d. Overbalance is reduced by 237 psi
18- If the negative pressure loss is 100 psi while pulling pipe, and if the formation pressure
gradient 0.75 psi/ft at 9000 ft , and the mud gradient 0.764 psi/ft the well would:
19- Pump stroke counter is the accurate to measure the mud to keep the hole full when
P.O.O.H.
a )true b )false
20- On mud pump, oil level for both gear box and chains should be checked
a- Weekly b- Daily c- Each Tour
[5]
23- The sand trap compartment below the shale shaker is a very important part of the mud
/solids separation.
a- False b- True
26- What are the causes of shale to sloughs into the hole?
28- The driller’s decision to pull a worn drill bit should be based on :
a- Other bit records in the area. b- The rotary torque requirements.
c- The drilling rate d- All of the above.
29- If the mud checked with V-G meter and the following numbers recorded, at 600 RPM is
85 & at 300 RPM is 50 .What would the yield value be ?
a. 25 LB.F/100 FT2 c- 35 LB.F/100 FT2
b. 5 LB.F/100 FT2 d- 15 LB.F/100 FT2
31- When gas is percolating the correct gauge to monitor / to maintain constant BHP during the
weighting up period is:
[6]
32- When a kick is detected while pulling out of the hole :
a. The well secured, pressures and gain recorded, back pressure valve
b. installed , and if bop condition and arrangement permits, strip back to bottom.
c. The well should be shut in and killed at this depth based on closedin pressure.
d. The well-secured safety valve installed & pipe stripped to bottom.
e. If over half way out of hole , finish trip and pick up new bit and Back to bottom quickly.
33- Surface inside BOP equipment (Kelly safety valve) should not be tested when BOP’s are
tested.
a- False b- True
34- If the annulus and drill pipes are in communication, a choke adjustment on the annulus
will reflect a change on the drill pipe side.
a- False b- True
35- If the viscosity is low and if the drilling assembly is not balled up there is no negative
pressure loss.
a- False b- True
36- Vacuum pump on the degasser compresses gas inside the vacuum tank.
a- False b- True
37- When the three way valve is fully open, the vacuum in the vacuum tank is broken and
less mud pulled in.
a- False b- True
38- The main purpose of the discharge jet is to remove gas from the mud.
a- True b- False
39- The main purpose of the baffle plate in vacuum degasser is to allow the mud to form as a
thin layer so the vacuum can pull gas out of the mud.
a- False b- True
40- Use an “S” to indicate which of the following statements apply to soft formation bits or
“H” to indicate statements applies to hard formation bits.
[7]
41- How do you know if you are getting good hole cleaning?
a. -
b. -
c. -
42- What effect on mud properties while drilling in shaly formations?
a. -
b. -
c. -
43- Why should pump pressure be limited on surface hole drilling?
a. -
b. -
c. -
44- How can you check the annular volume if the hole is washed out?
a. -
b. -
c. -
45- How can you control deviation in surface hole?
a. -
b. -
c. -
46- How can you control sand content while drilling surface hole?
a. -
b. -
c. -
47- What drilling functions tell the driller a twist-off has occurred?
a. -
b. -
c. -
48- Describe briefly how to make up a new D/C for the first time to run in the hole ?
a. -
b. -
c. -
49- How can you decrease the differential pressure?
[8]
a- Lighten the mud.
b- Increase the hydraulic power.
c- Decrease the viscosity of the mud.
d- All of the above.
50- Which of the following mud additives improve filter cake quality and help prevent
differential sticking?
a- Oil b- Starch c- Bentonite
51- The bottom pipe rams on the BOP stack should be used to:
a- Test other stack components.
b- Run casing with.
c- Secure well and make repairs on upper stack under emergency conditions
e- Circulate kicks up.
a- False b- True
57- Hydrogen sulphide is lighter than air and will float up from the B.O.P to the rig floor.
a- False b- True
[9]
With our best wishes
www.petroleumbook.
com
[10]