Professional Documents
Culture Documents
Annex-III List of Experiments
Annex-III List of Experiments
E2. To determine the Young’s modulus of the material of a rectangular beam by bending method
E3. To determine the specific rotation of sugar solution and hence determine the unknown concentration
of solution
E4. To determine the wavelength of a monochromatic light using diffraction grating
E5. To study the I-V characteristics of a rectifier diode and use it as a full wave rectifier
E6. To study the I-V characteristics of a Zener diode and use it as a voltage regulator
E7. To study the output characteristics of common emitter (CE) transistor configuration
E8. To design a common emitter (CE) amplifier and study its frequency response
Annex-III List of experiments 2
5. To design and construct a monostable multivibrator and determine its pulse width.
7. TO design and construct an astable multivibrator and to determine its frequency of oscillation.
1. To study the characteristics of a single phase transformer and determine the following:
i) voltage and current ratios of transformer
ii) Voltage regulation of the transformer with varying load
2. To study the operation of the following logic gate using DL & DTL:
i) AND Gate ii) OR gate, iii) NOT gate, iv) NAND gate,
v) NOR gate
3. To study the function of a Half-adder and Full-adder.
4. To construct and study the characteristics of J-K flip flop using NAND gate only.
5. To construct a law pass filter and find the following:
i) Cut-off frequency, ii) characteristic impedance
ii) Attenuation constant iv) Phase constant
1. Study the characteristics of an Emitter follower and its use in voltage stabilizer.
2. Construct a Radio transmitter and study its operation.
3. Construct a TRF receiver and study its operation.
4. Study the electrical characteristics of a solar cell and find its efficiency.
5. Study the characteristics of reflex klystron.
6. Study the Hall-effect in Semiconductors.
7. Electronic Workshop
3. Study the following characteristics of an Operational Amplifier, (a) Input bias current, (b) Input offset
voltage, (c) Common mode refection ratio & (d) Slew rate.
4. Study the characteristics of a UJT and construct a relaxation oscillator using it.
5. Study the Operational amplifier as (a) Inverting amplifier, (b) Non-inverting amplifier & (c) Difference
amplifier.
6. Study the characteristics of a SCR and use it as a power controller.
7. Use Operational amplifier to construct (a) Differentiator &(b) Integrator.
8. Construct a Phase shift oscillator and determine its frequency of oscillation.
9. Construct a Colpitts oscillator and determine is frequency of oscillation.
10. Design and construct an Astable multivibrator and determine its frequency of oscillation.
11. Design and construct a one shot multi vibrator and determine its pulse width.
12. Computer Lab : ( C ++)
A1. Construct and study the characteristics of the following Active Filters –
(i) Low-pass filter, (ii) High-pass filter, (iii) Band-pass filter and (iv) Notch/Band-stop filter.
A2. Construct and study the following circuits using NAND gates only.
Annex-III List of experiments 4
(i) S-R flip-flop, J-K master-slave flip-flop, D-type flip-flop and T-type flip-flop
(ii) Oscillator of different frequecies
(iii) Monostable multi-vibrator.
(i) Summer
(ii) Sine wave generator
(iii) Square-wave generator
(iv) High-precision rectifier
A4. Using 555-timer, construct and study - (i) Astable multi-vibrator, (ii) Monostable multi-vibrator, (iii) Bistable
multi-vibrator and (iv) Schmitt-trigger circuit.
A5. Study the electrical characteristics of a solar cell and find its efficiency.
B2. Solve the given arithmetic and logical problems by programming an 8085 microprocessor.
(N.B. values for (ii) and (iii) will be given by Lab Instructors)
Simulate the following circuits using VHDL and implement onto an FPGA.
And-Or-Inverter (AOI)
Or-And-Inverter (OAI)
D-Latch
Multiplexers
Demultiplexers
Counters (4-15 bits, Up)
Counters (4-15 bits, Down)
Even/Odd Parity Checker
“01” String Detector
Full-Adder (2-4 bit)