Professional Documents
Culture Documents
Barista Training Basics: Understanding How The Coffee Bean Begins
Barista Training Basics: Understanding How The Coffee Bean Begins
Decaffination Methods
To avoid certain effects of caffeine, there are three methods designed to remove up to 97% of the caffei ne from the
bean.
Conventional Method - this process removes caffeine by soaking the beans in a chemical solvent. This method is no
longer used due to health concerns.
Swiss Water Method - this process begins by soaking the beans in hot water. The hot water, after drawing out the flavor
of the beans, is run through a carbon filter, which traps and removes the caffeine. New beans are then added to this
water, because the water is already saturated in coffee, the caffeine is drawn out while the flavor of th e coffee is
preserved.
Co2 Method - This process decaffeinates the bean with liquid carbon dioxide, which can be pressurized and chilled
acting like a gas and a liquid combined. The equipment needed for this process is so large it is difficult to accommodate
smaller bean batches. This is generally used for volume not for taste.
Espresso Machines
Manual Espresso Machines - these machines require a lever, which the Barista controls. The lever is pushed down to
force the water through the grounds.
Semi-Automatic Espresso Machines - an espresso machine that is manually controlled by the Barista. The Barista
must start and stop the shot using an electronic switch, requiring careful watch and timing during the extraction process.
Automatic Espresso Machines - these machines are programmed to regulate the amount of water dispersed for each
shot. The Barista must set up shots correctly and then push a programmed button to begin the extraction process.
Careful watch is still required to ensure the pour is running correctly and the program stops extracting at the correct
amount of time.
All espresso machines must produce 130 pounds of pressure and be able to reach between 192- 203 degrees.
Espresso Machine Group or Group Head - the group head is the part of the machine where all the magic takes place.
Sometimes referred to as the brew group or brew head. This component is more commonly known simply as the group.
This part is where you insert the portafilter when preparing to extract espresso. The group showers pressurized hot
water through the diffusion plate over the bed of freshly ground and tamped espresso.
Portafilter - the portafilter is the device you grind coffee into and then place in the group to brew coffee. The name is
easy to remember as long as you think of it as a portable filter (porta-filter) Also known as a filter handle, and that thingy
you put the coffee into.
Portafilter Basket - the portafilter basket is the filter screen located in the portafilter. These come in both double and
single sizes, and are held in place by a spring.
Group Gasket - The group gasket is a large rubber o-ring that seals the portafilter to the group. It is inserted into a
groove machined into the group. Usually if the portafilter is leaking this is the part you need to replace.
Group Screen - the group screen is also located in the group. The group screen is sometimes referred to as a
dispersion screen, shower screen or simply shower.
It is considered best practice to replace the Portafilter Basket, Group Gasket and Group Screen on a quartery basis or
every three months or so.
Steam Wand - the steam wand is the part of the machine that you steam milk with. The steam wand is also known as a
steam pipe. The steam wand is activated by the steam valve and steam valve knob or lever.
Steam Tip - The steam tip is located on the end of the steam wand. This is the part that disperses the steam from the
wand into a splayed pattern allowing you to steam milk.
Hot Water Tap - Some call this the Americano wand or tap. It is simply a hot water tap. Call it what you will, this is where
you dispense hot water.
Group Dosing Keypad - Dosing keypads are found on automatic and super automatic espresso machines. These are
the buttons that you depress to activate the group head on the machine. The keypads show a legend of various dispense
times and quantities as well as programming and continuous flow.
Group Dispense Switch - The dispense switch acts much the same as the dosing key pads, but is usually a simple on
off switch located over the top of the group it actuates. Some automatic function machines also include a dispense
button as an additional means of group operation.
Power Switch - The power switch on most espresso equipment is located on the backsplash of the machine. It is often
indicated by a faceplate showing the numbers 1-0-2. The general position for full operation is the number 2 position.
Pressure Gauge - The pressure gauge is located on the front of the machine. It usually has two needles indicating both
boiler pressure and pump operating pressure. This is an import part to be aware of as it monitors the health of your
machine as well as the parameters of your coffee brewing temps and pressures.
Sight Glass - Most machines have a site glass. This part is located on the front of the machine and its purpose is to
indicate the boilers water level. The site glass is typicall y a glass tube with water in it. It is marked with Maximum and
Minimum markings.
Top of Machine - The vented top of the espresso machine was designed to keep ceramic cups warm prior to serving.
Drain Grate or Trough - Used with drip pan and drain, area where liquid drains.
Espresso Grinders
Burr grinders shave the coffee bean into precise microscopic flakes.
Espresso grinders also have a few specific part names. These names are important to know and you should have an
understanding of each part's function.
Adjustment Ring or Knob - This is the part where you make changes to the grind size with reference to course or fine.
The adjustment ring or knob is usually found it the area around the bean hopper.
Bean Hopper - This is the large clear plastic container located on top of the grinder.
Doser - The doser is the part of the grinder that holds the ground coffee. A lever is pulled to dispense the grounds into
the portafilter.
Adjusting the grind - The grind is one of the essential components in creating the ultimate espresso beverage. You
must only grind to order, as once coffee is ground it immediately starts to lose its flavor and aroma. You will need to
monitor your grind constantly; you want to grind to a powder like consistency, with a slightly g ritty feeling. If the grind is
too coarse (fast) it will result in a sour, weak, watery taste, too fine (slow) will result in bitterness. Acid is the first thing
extracted from the coffee, followed by sugar and eventually caffeine. The thickness of the cre ma determines the
perfection of an espresso.
Water Purity
Being that Espresso is 90% water, water becomes a key essential ingredient in espresso preparation. Having a water
filtration system becomes a must, especially in areas with hard water. Not having a filter will affect the taste of your
espresso as well as the lifespan of your equipment.
Beginning of Day/Opening Shift Espresso Machine Set-Up
At the beginning of your day when setting up your machine, it is necessary to run shots through each portafil ter. These
shots are called "seasoning shots"¥. This is done to ensure that any debris, cleaning detergent, etc. that may have
settled overnight in your machine is flushed out prior to making your first customers drink. At this time you will also be
able to see where your grind is and make adjustments accordingly.
Espresso Extraction
The portafilter needs to remain in the machine at all times so as to retain the correct temperature when shots are to be
pulled. Purging the machine gets residue out from the group head and helps the machine stay at the right temperature
for extraction. Start by drying the portafilter basket with a dry towel, this helps remove old excess coffee, but more
importantly it helps the packed coffee stick to the sides of the basket fo rming a water tight seal. Water likes to go where
water already is so drying the portafilter ensures a good seal.
Fill portafilter so that the basket is overflowing with coffee. With the lid of the grinder doser, scrape the overflowing
grounds leaving a slightly dipped, smooth look. Place the lid back on the doser and proceed with tamping procedures as
follows.
Tamping
With elbow up in the air at a 90 degree angle, firmly pack grounds with hand tamp using 30 pounds of pressure. (Not
having at least 30 pounds of pressure packing the grounds in the basket will create a loose pack, which will cause the
water pressure to blow a hole into the grounds.) Use a downward twisting motion when coming up out of the tamp. Your
goal is to have an even, level surface, which will force the water to go through the grounds evenly. If too much coffee is
put in the basket, it doesn't leave enough room for expansion, which occurs before brewing. A gap is needed for the
water to spread evenly over the surface of the grounds. Wipe off any excess grounds that sit loosely on top of and
around edges of the basket. This will ensure a snug fit and will prevent damage to the rubber gasket located inside the
group head. Purge the machine again before inserting portafilter into the group h ead, this helps machine regulate correct
temperature for extraction. Judge your shots by the color and the crema. Your goal is to extract a rust colored crema that
lasts for a long time. Extraction of shots should start out as a drip, drip then continue po uring in a syrup-like consistency
about the width of angel hair pasta, lasting anywhere from 20-26 seconds.