Professional Documents
Culture Documents
Manual of Desk Model
Manual of Desk Model
1 / 10
Introduction:
Ticket eater is a automatic machine for counting and cutting redemption tickets;
There is dot matrix LED display to show the quantity of counted tickets;
it can also connect card reader system to work smoothly;
the slim body will save shipping cost and won’t take up much space in amusement center.
Kind note:Please clear dust for machine both inside and outside in regular.
Technical Specification:
Voltage range: 110V~240V adjustable
Power: 600W
Counting speed: 720 tickets per minute
Dimension:(D)380mm*(W)340mm*(H)300mm
Weight:8.5KGS
Installation Guide:
Please install this machine indoor and place it on the flat counter which has enough space
to contain counted tickets.Be far away from anything of excessive heat/humidity .Be sure
of the connection to “earth” is valid.Any repaired or maintained measures must be
operated by qualified and trained staff or under the guidance of our engineers. Thanks for
your cooperation!
Inner Structure:
2 / 10
Advantage of ticket eater:
2. Main board
All-chip production, regulator control, software stability, more practical for user.
If you want to connect this ticket eater with card reader system,please connect
wires as the following diagram:
3 / 10
4 / 10
Reprinting Function Setting on main board:(only for ticket eater with printer)
K2:reprinting
5 / 10
3.Imported Original Japanese Motor
Original imported from Japan. 5 years warranty. It can be used continuously and won’t
hot.it is safe for user.
6 / 10
4.Imported original counting sensor
Inducing sensor:to start the motor when induce the ticket in
Counting sensor:count the quantity of ticket in. Counting accuracy, high precision, fast
response, non-contact.Durable and strong anti-interference.The unique appearance
increases the width of the collected beam to achieve better results.
7 / 10
Packing
Safe package: Plastic + Shockproof nylon+ carton
Package Contents:
1 x ticket entrance
1 x a set of gears
1 x Brush
1 x Knife
1x Manual
8 / 10
How to solve the problem?
A、when turn on machine,the screen display nothing,How to solve the problem?
1. please check power cord if connecting is good.
2. please check door switch if working well
3. please check the fuse beside of door switch if working well.
4. please check the power supply and transformer if working well.
5. if all are working well, please send back main board to examine and repair.
B、When turn on machine,the screen can display,but motor can not be working,How to
solve the problem?
1. Please clean the eye sensor in the front of entering ticket’s set.
2. Please check the fuse on the main board if fuse is fault
3. Please check eye sensor if it connects with main board well
4. Please change a new main board to test if it is main board’s problem
C 、 When turn on machine,screen and motor are in good situation,but do not count
ticket,How to solve the problem?
1. Please clean the eye sensor in the back of entering ticket’s set.
2. Please Check Eye Sensor If It Connects With Main board Well
3. please check the bulbe under the entering ticket’s set if it is good
4. please change a new main board to test if it is main board’s problem
E、The motor goes on working all the time, don’t stop,How to solve the problem?
1. Please clean the eye sensor in the front of entering ticket’s set.
2.Moc 3022 or bta 08 is fault,please change new one
3. Please Change A New Main board To Test If It Is Main board’s problem
9 / 10
I、Entering ticket position is jammed,How to solve the problem?
1. please check the entering ticket position if anything is locked
2. please clean the ticket position by electronic fan.
3. please check if the cutting knife is broken.
Daily Maintenance
1、Keep ticket eater cleaning,please use cleanser to clean the ticket entrance.
2 、 Please clean the cutter kit and e-eye in regular,in order to keep machine working
normally and counting exactly(Don't break up the e-eye to clean!)
3、When machine is working for a long time,there is much dust and wastepaper inner of
cabinet,then please clean them by brush in fixed time.
4、Keep the cutter kit dry,and avoid to oil lube or cleanser on it,or the cutter's use life will
be shortened .
10 / 10