Professional Documents
Culture Documents
Alarmas EX ALL MoriSeiki
Alarmas EX ALL MoriSeiki
5, Any wrong
combination M-commands have been mistakenly given at the same time.
EX0018, NEED ZERO-RETURN, ALM0018, A0.2, A cycle start has been activated
without executing the X-axis and Z-axis zero returns after a machine lock cancel.
EX0020, EDITING SWITCH KEY IS ON, ALM0020, A0.4, A cycle start has been
activated with the Editing Key Switch on.
EX0024, CHUCK UMCLAMPED, ALM0023, A0.6, A cycle start has been activated
with the chuck unclamped.
EX0026, DOOR NOT CLOSED, ALM0026, A0.7, The cycle operation has mistakenly
been started without door closed.
EX0029, TAILSTOCK INCHING/ QUILL NOT OUT, ALM0029, A1.0, A cycle start
has been activated during tailstock inching or with the tailstock quill not OUT.
EX0033, ONLY HANDLE MODE, ALM0033, A7.6, The jog push button has been
pressed together with the O.T. release button after the hard O.T. limit switch has been
tripped.
EX0068, SET UP MODE TIME OVER, ALM0068, A10.2, Door interlock cancel
time has been over.
EX0069, DOOR LOCK CHECK TIME OVER, ALM0069, A10.3, Door lock
complete signal has not been turned ON after elapsing the time set in timer.
EX0334, TURRET PARAM. MUST BE 8, 10, 12, ALM0344, A2.1, A value other
[8], [10], or [12] was input to the paramter as a setting for the number of turret station.
Reset the parameter.
EX0350, PHASE-B SIGNAL NOT ON (#2), ALM0350, A12.1, The turret indexing
phase-B count signal has not been activated. This error is caused when a phase-A signal
is output twice in a row. Either the proximity switch for the phase-B counter is defective
or it is improperly adjusted. (Head2).
EX0351, PHASE-A SIGNAL NOT ON, ALM0351, A14.0, The turret indexing phase-
A count signal has not been activated. This error is caused when a phase-B signal is
output twice in a row. Either the proximity switch for the phase-A counter is defective
or it is improperly adjusted. (Head2)
EX0352, PHASE-B SIGNAL NOT ON (#1), ALM00352, A10.7, The turret indexing
phase-B count signal has not been activated. This error is caused when a phase-A
signal is output twice in a row. Either the proximity switch for the phase-B counter is
defective or it is improperly adjusted. (Head1)
EX0353, PHASE-A SIGNAL NOT ON (#1), ALM0353, A11.0, The turret phase-A
count signal has not been activated. This error is caused when a phase-B signal is output
twice in a row. Either the proximity switch for the phase-A counter is defective or it is
improperly adjusted. (Head1).
EX0355, PHASE-A NOT AGREE WITH PHASE-B (#1), ALM0355, A11.1, Current-
position data in the phase-A signal counter and the phase-B signal counter do not agree.
Either the proximity switch for the counter is defective or it is improperly adjusted.
(Head1)
EX0356, TURRET INDEX TIME UP (#2), ALM0356, A17.0, Turret indexing has not
been completed within the specified time. (Head2)
EX0357, TURRET INDEX TIME UP (#1), ALM0357, A11.2, Turret indexing has not
been completed within the specified.
EX0374, TOOL LIFE UP (#1), ALM0374, A11.3, Tool life up. (Head1)
EX0375, TOOL LIFE UP (#2), ALM0374, A17.1, Tool life up. (Head2)
EX0386, NEED TURRET ZERO RETURN (#1), ALM0386, A12.0, The turret clamp
check limit has been deactivated during cycle start. (Head1)
EX0393, NEED TURRET ZERO RETURN, ALM0393, A17.4, The turret clamp
check limit switch has been deactivated during cycle start.
EX0405, M41, M42, M43, M44 COMMAND MISSING, ALM0405, A2.4, An M3,
M4 or M19 command has been given without giving either an M41, M42, M43, 0r M44
command.
EX0407, BAD SPINDLE DIRECTION, ALM407, A2.6, The direction of spindle (or
milling) rotation has been changed or while shifting the operation mode from automatic
to manual, or from manual to automatic.
EX0411, M3/M4-COM WITH SPINDLE JOG ON, ALM0411, A3.0, A M3, M4, or
M39 command has been given during spindle jogging.
EX0429, M13/M14/M39 BUT MILLING JOG ON, ALM0429, A3.3, A M13, M14,
or M39 command has been given during milling jogging.
EX0448, M-COM BUT NOT AT MILL STATION, ALM0448, A3.4, With the rotary
tool station not indexed, either anM13, M14, M39 or M3, M4 during M90 command
mode, command has been given.
EX0449, NOT MILLING STATION, ALM0449, A3.5, A G251 (polygon) command
has been given at the position other than the milling stations.
EX0451, SPINDLE DRIVE UNIT ALARM, ALM0451, A12.1, The spindle drive unit
alarm has been activated.
EX0453, MILL SPINDLE ALARM, ALM0453, A12.3, A milling amplifier alarm has
been activated.
EX0456, SPINDLE INDEX TIME UP, ALM0456, A12.4, Spindle indexing has not
been completed within the specified time.
EX0461, TAILSTOCK OUT SWITCH NOT ON, ALM0461, A12.5, The tailstock out
check signal has been deactivated with the tailstock quill out.
EX0470, GEAR CHANGE TIME UP, ALM0470, A12.6, Gear change has not been
completed within the specified time.
EX0471, GEAR CHECK LIMIT SWITCH NOT ON, ALM0471, A12.7, The gear
check limit switch has been deactivated during spindle rotation.
EX0554, OIL AIR PRESSURE STILL DOWN, ALM0554, A10.4, No increase in oil
air pressure. Possible cause is broken piping or motor failure.
EX0560, AIR PRESSURE DROP, ALM0560, A13.2, Air pressure has dropped.
EX0563, NO DROP IN LUBR. OIL PRESSURE, ALM0563, A13.5, Pressure has not
decreased within the specified time after turning the cycle pump OFF. Possible cause is
failure in the pressure switch or the magnet.
EX05564, NO DROP IN OIL AIR PRESSURE, ALM0564, A10.5, Pressure has not
decreased within the specified time after turning the oil air pump OFF. Possible cause is
failure in the pressure switch or the magnet.
EX0590, THERMAL TRIP, ALM0590, A10.1, One of the thermal relays in the
auxiliary motor has been tripped.
EX0905, PRESETTER ARM DOWN, ALM0905, A8.2, The parts catcher OUT
command has been given with the presetter arm rise check switch deactivated.
EX0907, PRESETTER ARM DOWN, ALM0907, A8.4, The presetter arm rise check
switch has been deactivated while the parts catcher is out.
EX0911, NO MORE BAR STOCK, ALM0911, A3.7, Bar stock has run out.
EX0923, SENSOR ON, ALM0923, A7.2, An M72 command has been given while
sensor is turned on.
EX0946, ROBOT ARM IN, ALM0946, A4.5, The following commands have been
given while the ROBOT arm is moving IN. (M8, M3/4, M13/14, M38, M39, M71,
M86, T-command)
EX0951, CONTACT BUT NO PRESET MODE, ALM0951, A14.2, The sensor has
been activated without setting the presetter mode.
EX0952, CONTACT AS ARM RISES, ALM0952, A14.3, The sensor has been
activated with the presetter ascending.
EX0953, ARM UP SIGNAL OFF IN AUTO MODE, ALM0953, A14.4, The presetter
arm UP detection signal has been deactivated during automatic mode.
EX0956, TWO OR MORE SENSORS ARM ON, ALM0956, A14.5, Two sensors or
more have been activated during presetter mode.
EX0957, PARTS CATCHER TIME UP, ALM0957, A14.6, The parts catcher
operation has not been completed within the specified time.
EX0962, ROBOT CYCLE TIME UP, ALM0962, A15.0, ROBOT cycle has not been
completed in the specified time.
EX0966, ROBOT ALARM, ALM0966, A15.3, The ROBOT alarm has been output.
EX0967, LOADER EMG STOP, ALM0967, A20.4, The loader state is in emergency
stop state.
EX0968, NO MORE BAR STOCK, ALM0968, A15.4, Bar stock has run out.
EX0979, CHUCK CLAMP TIME UP, ALM0979, A17.6, The chuck clamp operation
has not been completed within the specified time when work seating check spec.
EX1005, PUT IN THE NEW MATERIAL, ALM1005, A4.6, Please supply new work
piece.
EX1024, DOOR MUST BE OPENED ONCE, ALM1024, A4.7, Open and close the
door before starting new cycle.
EX1036, TEACHING ALARM (#1), PER1036, A18.1, Alarm occurs during teaching
mode. (#1)
EX1045, TEACHING ALARM (#2), PER1045, A19.1, Alarm occurs during teaching
mode. (#2)
EX1053, Z-AXIS LOAD WARNING (#1), MER1053, A18.4, Z-axis overload warning
level. (#1)
EX1067, DOOR CLOSE SIGNAL OFF, ALM1067, A2o.1, Auto-door close detection
signal turns off.
EX1068, DOOR OPEN/CLOSE TIME OVER, ALM1068, A20.2, Auto door open or
close detect single was not turned on within allowable time.
EX1069, DOOR SENSOR TEST ERROR, ALM1069, A20.3, Area sensor input
signal (X1009.5) does not turn off.
EX1303, M25/M26 BUT SPINDLE ON, ALM1303, A5.3, An M25 or M26 command
has been given during spindle rotation.
EX1416, M3/M4/M19 BUT SPINDLE BRAKE ON, ALM1416, A5.6, An M3, M4, or
M19 command has been given with the spindle brake activated.
EX1421, M13/M14 BUT SPINDLE BRAKE OFF, ALM1421, A6.1, An M13 or M14
command has been given with the spindle brake not activated.
EX1422, PRESETTER ARM NOT FULLY RAISED, ALM1422, A6.2, An M3, M4,
M13, M14, or M39 command has been given with the presetter arm not fully raised.
EX1424, M-COMMAND BUT SPINDLE ON, ALM1424, A6.3, An M39, M40, M45,
M68, M90, M91 or M312 command has been given during spindle rotation.
EX1426, M-COMMAND BUT MILL ON, ALM1426, A6.4, An M39, M46, M69,
M90, or M91 command has been given during milling rotation.
EX1457, OIL COOLER ALARM, ALM1457, A16.1, Oil cooler is overloaded or oil
temperature is abnormal.
EX1458, MILLING HOLDER JOIN TIME UP, ALM1458, A16.2, Milling holder
has not joined to the drive within the specified time.
EX1921, M/S/T CODE IN SAME BLOCK, ALM1921, A7.1, M85/86 command and
T/S-code command have been given in the same block. Specify M85/86 in a single
block.
EX1928, DOOR NOT CLOSED, ALM1928, A3.6, Shutter open/close command has
been given while the front door is not closed.
EX1937, SPINDLE ON, ALM1937, A08.1, An forkardt chuck index command has
been given during spindle rotation.
EX1958, ROBOT POWER NOT TURNED ON, ALM1958, A17.7, Robot power is
not turned ON.
EX2028, PUSH SINGLE BLOCK SW. ON, ALM2028, A08.7, Cycle start button was
pressed at single block OFF status.
EX2029, CYCLE START NOT PERMITTED, ALM2029, A09.0, Single block was
turned off or door was opened during automatic cycle.
EX2033, DOOR SENSOR DETECT, ALM2033, A09.7, Area sensor detects obstacles
after specifying auto-door close command.
Check out www.pinpointcnc.com for machine repair information, procedures and other
products.