Professional Documents
Culture Documents
LT PDF
LT PDF
LT
A
B
SECTION
LIGHTING SYSTEM C
E
CONTENTS
SERVICE INFORMATION ............................ 2 COMBINATION SWITCH .................................. 20 F
Replacement ...........................................................20
PRECAUTIONS ................................................... 2
Precaution for Supplemental Restraint System SIDE TURN SIGNAL LAMP .............................. 21 G
(SRS) "AIR BAG" and "SEAT BELT PRE-TEN- Bulb Replacement ...................................................21
SIONER" ................................................................... 2 Removal and Installation .........................................21
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. Information necessary to service the system safely is included in the SRS and SB section of
this Service Manual.
WARNING:
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the SRS section.
• Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-
ness connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
• When working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors with the Igni-
tion ON or engine running, DO NOT use air or electric power tools or strike near the sensor(s) with a
hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers, always switch the Ignition OFF, disconnect the
battery, and wait at least 3 minutes before performing any service.
ALLIA0868ZZ
E
1. Combination switch (lighting switch) M29, M30 2. Combination meter M206 (with tachometer),
M207
F
System Description INFOID:0000000008944690
AALWA0012GB
LT
AALWA0647GB
(+)
(−) Voltage
Headlamp connector Terminal
RH E1
1 Ground Battery voltage
LH E7 AWLIA1569ZZ
OK or NG
OK >> GO TO 4.
NG >> GO TO 5.
4.CHECK HEADLAMP GROUND CIRCUIT
Check continuity between headlamp harness connector and ground.
A B
Circuit Continuity
Connector Terminal Connector Terminal
RH 6 E1
M30 1 Yes
LH 9 E7
OK or NG
OK >> Replace combination switch. Refer to LT-20, "Replace- AWLIA1568ZZ
ment" .
NG >> Repair harness or connector.
Headlamp High Beam Does Not Illuminate (One Side) INFOID:0000000008944693
RH E1 Ground
2 Yes
LH E7 J
OK or NG
OK >> Check headlamp connector for damage or poor connec-
tion. Repair as necessary. LT
NG >> Repair harness or connector.
AWLIA1567ZZ
A B
Circuit Continuity
Connector Terminal Connector Terminal N
RH 6 E1
M30 1 Yes
LH 9 E7
O
OK or NG
OK >> Replace combination switch. Refer to LT-20, "Replace- AWLIA1568ZZ
ment" .
NG >> Repair harness or connector. P
(+)
(−) Voltage
Headlamp connector Terminal
RH E1
3 Ground Battery voltage
LH E7 AWLIA1572ZZ
OK or NG
OK >> GO TO 4.
NG >> GO TO 5.
4.CHECK HEADLAMP GROUND CIRCUIT
Check continuity between headlamp harness connector and ground.
A B
Circuit Continuity
Connector Terminal Connector Terminal B
RH M30 7 E1
3 Yes
LH M29 10 E7
C
OK or NG
OK >> Replace combination switch. Refer to LT-20, "Replace-
ment" . D
NG >> Repair harness or connector.
G
AWLIA1571ZZ
H
1.HEADLAMP LOW BEAM FUSE INSPECTION
Inspect 15A fuse [No. 38 (LH) and No. 37 (RH) located in fusible link and fuse box].
OK or NG I
OK >> GO TO 2.
NG >> Repair harness.
J
2.CHECK BULB
Check bulb of inoperative headlamp.
OK or NG LT
OK >> GO TO 3.
NG >> Replace bulb. Refer to LT-11, "Bulb Replacement" .
3.CHECK HEADLAMP INPUT SIGNAL L
A B
Circuit Continuity
Connector Terminal Connector Terminal
RH M30 7 E1
3 Yes
LH M29 10 E7
OK or NG
OK >> Replace combination switch. Refer to LT-20, "Replace-
ment" .
NG >> Repair harness or connector.
AWLIA1571ZZ
LEL378A
LT
WEL536A
If the vehicle front body has been repaired and/or the headlamp assembly has been replaced, check aiming.
Use the aiming chart shown in the figure. L
• Basic illuminating area (shaded) for adjustment should be within the range shown on the aiming
chart. Adjust headlamps accordingly.
Removal and Installation INFOID:0000000008944697
M
REMOVAL
N
1. Remove the radiator grille. Refer to EI-17, "Removal and Installation".
2. Disconnect the harness connectors from the back side of the headlamp assembly.
3. Remove the bolts and the headlamp assembly. O
INSTALLATION
Installation is in the reverse order of removal.
P
Bulb Replacement INFOID:0000000008944696
WARNING:
Do not touch bulb by hand while it is lit or right after being turned off. Burning may result.
CAUTION:
• Do not touch glass surface of the bulb with bare hands or allow oil or grease to get on it to prevent
damage to bulb.
LEL376A
INSTALLATION
Installation is in the reverse order of removal.
AWLIA1839ZZ
E
1. Combination switch (lighting switch) 2. Combination meter M206, M207 3. Combination flasher unit M21
M30
4. Hazard switch M59 (early production) 5. Hazard switch M59 (late production) F
G
TURN SIGNAL OPERATION
With the ignition switch in the ON or START position, power is supplied
• through 10A fuse (No. 10, located in fuse block) H
• to hazard switch terminal 2.
With the hazard switch in the OFF position and a turn signal activated, power is supplied
• through hazard switch terminal 1
• to combination flasher unit terminal 1 I
• through combination flasher unit terminal 3
• to combination switch terminal 1.
Ground is supplied J
• to combination flasher unit terminal 2
• through grounds M57 and M61.
LH Turn Signal Lamp LT
When the combination switch (turn signal switch) is moved to the left turn position, power is supplied
• through combination switch terminal 3
• to combination meter terminal 18 (without tachometer) or terminal 11 (with tachometer),
• to front combination lamp LH terminal 2, L
• to side turn signal lamp LH terminal 1 and
• to rear combination lamp LH terminal 2.
Ground is supplied M
• to front combination lamp LH terminal 1 and
• to side turn signal lamp LH terminal 2
• through grounds E15 and E24, and
N
• to combination meter terminal 40 (without tachometer) or terminals 24 and 36 (with tachometer),
• to rear combination lamp LH terminal 8 (with 8-way combination lamp connector) or terminal 6 (with 6-way
combination lamp connector)
• through grounds M57 and M61. O
With power and ground supplied, the left turn signal lamps and indicator flash.
RH Turn Signal Lamp
When the combination switch (turn signal switch) is moved to the right turn position, power is supplied P
• through combination switch terminal 2
• to combination meter terminal 44 (without tachometer) or terminal 28 (with tachometer),
• to front combination lamp RH terminal 2,
• to side turn signal lamp RH terminal 1 and
• to rear combination lamp RH terminal 2.
Ground is supplied
• to front combination lamp RH terminal 1 and
LT
AALWA0648GB
P
AALWA0637GB
1.CHECK BULB
Verify the bulb standard of each turn signal lamp is correct. Refer to LT-35, "Bulb Specification" .
OK or NG
OK >> GO TO 2.
NG >> Replace turn signal lamp bulb. Refer to LT-21, "Bulb Replacement" .
1.CHECK BULB
Verify the bulb standard of each turn signal lamp is correct. Refer to LT-35, "Bulb Specification".
OK or NG
OK >> GO TO 2.
NG >> Replace turn signal lamp bulb. Refer to LT-30, "Bulb Replacement".
2.CHECK REAR TURN SIGNAL LAMP CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect combination switch connector and rear combination
lamp LH or RH connector.
3. Check continuity between combination switch harness connec-
tor M30 (A) terminal 3 and rear combination lamp LH harness
connector T1 (B) terminal 2 (with 8-way combination lamp con-
nector) or connector T1 (C) terminal 2 (with 6-way combination
lamp connector).
A: M30 3 Yes
C: T1 (with 6-way combination lamp
2
connector)
4. Check continuity between combination switch harness connector M30 (A) terminal 2 and rear combination
lamp RH harness connector T7 (B) terminal 2 (with 8-way combination lamp connector) or connector T7
(C) terminal 2 (with 6-way combination lamp connector).
LT
L
AWLIA1579ZZ
SEL865L
MEL205B
• Before installing the steering wheel, align the turn signal cancel tab
with the notch of the combination switch. Refer to SRS-30.
ARS152
REMOVAL B
1. Remove the side turn signal lamp. Refer to LT-21, "Removal and Installation".
2. Remove the bulb and socket.
C
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
After installing bulb, be sure to install the bulb socket securely to ensure watertightness. D
E
REMOVAL
1. Slide the lamp towards the rear of the vehicle and remove the assembly from the front fender, front edge
first. F
2. Disconnect the harness connector.
INSTALLATION
Installation is in the reverse order of removal. G
LT
AALWA0638GB
LT
P
AALWA0639GB
ALLIA0871ZZ
The control of the parking, license plate and tail lamp operation is dependent upon the position of combination
switch (lighting switch). When the combination switch is placed in the 1st or 2nd position power is directed to
parking, license plate and tail lamps, which then illuminate.
Power is supplied at all times
• through 10A fuse (No. 4, located in the fuse block)
• to combination switch terminal 11.
OPERATION BY LIGHTING SWITCH
With the lighting switch in the 1ST or 2ND position power is directed
• through combination switch terminal 12
• to front combination lamp LH and RH terminal 3
• to rear combination lamp LH and RH terminal 1 and
• to license plate lamp LH and RH terminal 2.
Ground is supplied
• to front combination lamp LH and RH terminal 1
• through grounds E15 and E24,
• to rear combination lamp LH and RH terminal 3
• to license plate lamp LH and RH terminal 1
• through grounds M57 and M61.
With power and ground supplied, parking, license plate and tail lamps illuminate.
LT
AALWA0640GB
P
AALWA0187GB
(+)
C
(−) Voltage
Front combination lamp connector Terminal
RH E19 Battery D
3 Ground
LH E13 voltage
E
AWLIA1580ZZ
(+)
F
(−) Voltage
License plate lamp connector Terminal
RH B: T5 G
A: T4 (without step bumper) 2 Ground Battery voltage
LH
B: T4 (with step bumper)
H
AWLIA1581ZZ
I
(+)
(−) Voltage J
Rear combination lamp connector Terminal
A: T7 (with 8-way combination lamp con-
nector)
RH LT
B: T7 (with 6-way combination lamp con-
nector) Battery
1 Ground
A: T1 (with 8-way combination lamp con- voltage
nector) L
LH
B: T1 (with 6-way combination lamp con-
nector) AWLIA1582ZZ
OK or NG M
OK >> GO TO 4.
NG >> GO TO 3.
3.CHECK PARKING, LICENSE PLATE AND TAIL LAMP CIRCUIT N
1. Disconnect combination switch connector.
2. Check continuity between combination switch harness connec-
tor (A) and front combination lamp harness connector (B) or (C). O
AWLIA1583ZZ
AWLIA1584ZZ
Con- Termi-
Connector Terminal Continuity
nector nal
B: T7 (with 8-way combination
lamp connector)
RH
C: T7 (with 6-way combination
lamp connector)
A: M29 12 1 Yes
B: T1 (with 8-way combination
lamp connector) AWLIA1585ZZ
LH
C: T1 (with 6-way combination
lamp connector)
OK or NG
OK >> Replace combination switch. Refer to LT-20, "Replacement".
NG >> Repair harness or connector.
4.CHECK PARKING, LICENSE PLATE AND TAIL LAMPS GROUND CIRCUIT
1. Check continuity between front combination lamp harness con-
nector and ground.
AWLIA1586ZZ
AWLIA1587ZZ
LT
REMOVAL
1. Remove the rear combination lamp. Refer to LT-30, "Removal
and Installation".
2. Turn the bulb socket counterclockwise to remove the bulb and
socket.
3. Pull bulb straight out away from the socket to release.
WKIA3780E
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
After installing bulb, be sure to install the bulb socket securely to ensure watertightness.
Removal and Installation INFOID:0000000008944725
REMOVAL
1. Open the tailgate and remove the rear combination lamp bolts.
2. Pull the rear combination lamp rearward.
3. Rotate each bulb socket counterclockwise to unlock it from the
lamp assembly housing and remove the assembly from the
vehicle.
WKIA3781E
INSTALLATION
Installation is in the reverse order of removal.
ALLIA0872ZZ
E
1. Interior room lamp 2. Interior room lamp 3. Front door switch (driver side) M41
R4 (single cab) R5, R6 (double cab)
F
System Description INFOID:0000000008944727
When room lamp switch is in DOOR position, room lamp ON/OFF is controlled by front door switch driver’s
side. G
AALWA0641GB
The control of the illumination lamps is dependent upon the position of the lighting switch. When the lighting B
switch is placed in the 1ST or 2ND position, power is directed to the illumination lamps.
Power is supplied at all times
• through 10A fuse (No. 4, located in the fuse block)
• to combination switch terminal 11. C
LT
AALWA0642GB
HEADLAMP B
Wattage (W)*
High/Low (Semi-sealed beam) 60/55 C
*: Always check with the Parts Department for the latest parts information.
EXTERIOR LAMP D
Wattage (W)*
Turn signal (4WD) 27 E
Front combination lamp Turn signal (2WD) 21
Parking 5
Side turn signal 5 F
Turn signal 21
Rear combination lamp (Chassis) Stop/Tail 21/5
G
Back-up 21
License plate lamp 10
*: Always check with the Parts Department for the latest parts information. H
INTERIOR LAMP
I
Wattage (W)*
Room lamp (Dome lamp) 10
Map lamp 8 J
*: Always check with the Parts Department for the latest parts information.
LT